P3600 connector pinout - P3600 Software Upgrading

Hi Guy,
I'm loocking for a usb/audio pinnout of the P3600, because I made a small circuit for connecting my ex pocket device qtek 9090 to car stereo. Now I have a P3600 and nedd to change the connector.
bye,
dormone

I hope that pinouts are the same for Trinity and Hermes.
So You can find: http://www.tracyandmatt.co.uk/blogs/index.php/2006/09/10/htc_hermes_usb_connector_pin_config

It seems to be the correct connector. I will do some tests. Thanks a lot
bye

Related

Connecter difference MDA <-> MDA II ??!!

I found following problem: I am using now for quit a while a TomTom Navigator. On a MDA there is absolutely no problem, but if I connect the GPS Mouse to a MDA II or XDA II the PDA starts do beep an a MMS or WAP session will be started. Therefore I guess there is a difference in the Connector, probably only a very minor one. Founs somebody something comparable ??
There is NO difference, execpt for the Audio-out, it will only work with Pin19 shortened to ground for audio output.
Chargers, cables headsets etc. shopuld all work....
Hi !
I have the same problem with royaltek GPS.
Any help ?
DIFFERENT
On XDA2 pin2 is NOT GND !!!
Re: DIFFERENT
Sebi said:
On XDA2 pin2 is NOT GND !!!
Click to expand...
Click to collapse
Right, on BOTH it is Audio-ground.
If you think it is not on the XDA II, why does audio work with an XDA I carkit ?
make sure you have incoming beams turned off in the connections tab in systems
my old xda 1 used to do it when i plugged my gps into it ysed to dial up wap or connect to gprs lol when u turn that off it shoudl work fine

HBH-600 and Qtek 9090

Help, I bought a hbh-600 bluetooth headset but am not be able to connect it to my Qtek 9090. I can find the device and authorise it, but I am not able to connect to the device. Everytim I will connect to the device my Qtek 9090 says: Connection failed...
Help what can I do...
Had this problem yesterday with my step uncle's Harrier, and the HBH-600.. Just took a lot of fiddling around by turning bluetooth on/off, re-pairing, and it eventually worked.
I haven't seen this with my Harrier/HBH-600.. but I have had some general bluetooth issues.. About to try an upgrade to the 3500 build.
Can you tell me specific what you have done? Because I have tried that repairing and Bluetooth on and off also a few times...
Is it the authentification? Or is it something else.
Tnx!
:wink:
Well, no, not really sorry.. I was just mucking around, because he was in a hurry to leave... It just worked in the end. It may well not be the same problem anyway.. sorry.
the range on HBH600 sucks - mount it on the ear, and put 9090 in your trousers pocket or extend your arm while holding PPC - you will have very poor sound instantly.
Tnx all for the info. I have found the BT-PPC build 3500 patch and my bluetooth headset is working!!!
what's your radio firmware version now ?
Radio: 1.06.00
Bluetooth: BT-PPC build 3500

Belkin irda keyboard problems with imate pda2 and xda II

Hello, i have problems with belkin irda keyboard, don t work all the buttom........only 8-9 button work........
somebody can help me?
thank
mike

A2DP Patch for XDAIIi and Radio

Hi,
Have installed BT A2DP patch and seams to work for my keyboard (Thinkoutside) and ActiveSync plus my GPS (Navman BT). I will now think about getting a stereo headphone set something like Motorola H820 or Blueant X5.
However it seams I can only connect BT devices if the radio is on. There are times when I want the phone off but still be able to use BT.
Is there a setting I am missing or is this how the driver works.
Thanking in advance.
Gordon
Gordon,
it's just one of those interesting quirks - you need the phone on for BT (or wireless LAN) to be on.
Phil
You still may leave screen off. :lol: A2DP does not work again after power off. Usual handsfree profile works ok, when incoming call has been made.
where can I find BT A2DP for my alpine?
is there a link somewhere I can't see?, and, then, anyone know some installer/upgrade to go from 1.11.162 WWE to v1.11.171 WWE? I'm going mad to pair the Fortuna clip-on with my Alpine, and seems it doesn't work 'cause BT version on the fortuna is 1.1, on the Alpine is 1.0.0.3900. Is this correct?
thanx everyone, cya
Toobalz;
I'm having the same problem with my O2 BT clip on. I can't pair it with XDAIIi, but it works fine with XDAmini and XDAII.
Does anyone know why???
Cheers;
pc
ROM version: 1.11.00 WWE
ROM date : 01/27/05
Radio Version: 1.04.00
Protocol : 1337.42
ExtRom : 1.11.162 WWE
hey, everyone...I've solved my problems buying a tomtom...I know, it's a defeat, but I've to work faster....
And, for everyone who has an Alpine, I've discovered the TomTomOne car charger is identical, for voltage, polarity and amperage to a its normal AC adapter:
5V . 2A . (+)-o)(-); naturally, you've to unplug the plug from the Ac adapter and to plug it to the car charger.
In sintesi, if you've an Alpine, and buy a TomTomOne,don't you buy the car charger for the Alpine.
Hope so find this usefull, cya

gns tmc (mio) and htc tytn ii

Hello,
At the time, I bought a GNS TMC receiver for my Mio P550. For more info about the GNS TMC receiver, please have a look at http://www.gns-gmbh.com/catalog/product_info.php?cPath=28&products_id=117.
Since this receiver has a mini-usb connection I'm wondering if it could work on my Tytn II. I found that it does charge my Tytn, the only question is how to get TMC working on my device. Does anybody know this? Can anybody help? Does anyone have some suggestions to try?
The software I'm working with is MioMap v3.2 or Route 66 navigate 7. This used to work on my mio p550, off course i prefer it on my Tytn II
Thanks for all help!!
Dennis
A response from GNS:
"thank you for your inquiry. Sorry the PDA HTC Tytn II has only a USB-Client connector. in this case the HTC Tytn II canĀ“t use TMC-receiver with cable."
Is this true; don't they react like this to palm me off?
tnx

Categories

Resources