Related
Hello All,
I have problem with my XDA Mini s,
I upgraded the wizard with WM6 with undercover version from this site.
my wizard starts unable to catch the signal.
I thought of go bck to WM5 but my pc is not detecting my wizard.
I loaded MS active sync 4.5 still it is unable to detect the wizard.
I request you all pls guide me how to restore my wizard
thanks in advance
regards
saju
NOTE: The following is for an Unlocked G3 Wizard...
Try getting to the boot loader and you can probably flash your phone:
* Turn off your phone (pull the battery if you have to)
* Plug in your USB cord
* Hold down the Camera button and then turn on your phone
You should get to the "Rainbow" screen and it will say USB in the bottom left. If so, now flash the TMobile Ship ROM (2.26) onto your phone (or some official 2.x ROM, but I like to go to the TMobile one now). When the phone reboots, make sure both your IPL and SPL show 2.26 (or the same version for the ROM you flashed).
Thanks a lot.
solution worked out.
Excellent. Works perfect. Thanks a lot
This guide was written a long time ago. I recommend people to use this more up to date guide:
Wizard Windows Mobile 6 for newbies
I've got a lot of post behind my name, but most of my posts are answers to the same questions over and over again. It seems very hard for "noobs" to find the answer to their question quickly on the forum. I quickly wrote a little step by step tutorial for them. Hope it helps!
Suggestions or corrections are always welcome.
You want to flash your wizard, but don't know where to start. Try this:
0. First determine if you got a G3 or a G4 device. When you turn on your device from can can see you're IPL and SPL version on the screen. If you got IPL/SPL 1.xx or 2.xx you've got a G3 device. If the IPL/SPL shows 2.xx.xxx1 you've got a G4. Go to step G3.1 if you got a G3 and G4.1 if G4.
G3.1 Does you're device start normally (yes) or is it stuck on the three-colored bootloader screen (no)? YES... go to step G3.5, NO go to step G3.2
G3.2 Turn off you're device totaly. Remove the SD card and disconnect the USB cable from you're device. Turn on the device while holding the camera button. You will get into bootloader mode (3 colored screen). Connect the USB cable to the computer and you will see USB at the bottom of your screen above the left softkey (Activesync will not connect in bootloader mode, but you can flash from this screen!). If you got IPL/SPL 1.xx go to G3.3. If you got 2.xx go to G3.4
G3.3 Download button rom and flash it to your device. Your device should startup again after doing this. Go to G3.5.
G3.4 Download wizard_love rom and flash it to your device. Your device should startup again after doing this. Go to G3.5.
G3.5 Is your device CID-unlocked (note: it's not the same as SIM-unlocked!)? YES... go to step G3.7, NO OR DON'T KNOW go to step G3.6.
G3.6 Follow this great thread by Dr Puttingham: The Definitive Guide to Unlocking & Rom Upgrading G3 Wizards. Don't skip step 17! Flash the T-Mobile 2.26 Rom! Go to step G3.8 if you got the T-Mobile rom with IPL/SPL 2.26 on your device after doing this.
NOTE: Some people seem to have problem with flashing the button rom in this step (stops at 98% with error 302). Replace button_rom with Xda_MiniS_LaunchROM_v154102 and follow the rest of the steps normally when this happens!
G3.7 Download T-Mobile 2.26 rom and flash it to your device! Done? Go to step G3.8.
G3.8 You're reade to flash the AKU2, AKU3, WM6 rom of you're choise! It wasn't that hard, was it? If you still got an older OS version after flashing then you're not CID-unlocked! Go back to start!
------------------------------------
G4.1 Does you're device start normally (yes) or is it stuck on the three-colored bootloader screen (no)? YES... go to step G4.4, NO go to step G4.2
G4.2 Turn off you're device totaly. Remove the SD card and disconnect the USB cable from you're device. Turn on the device while holding the camera button. You will get into bootloader mode (3 colored screen). Connect the USB cable to the computer and you will see USB at the bottom of your screen above the left softkey (Activesync will not connect in bootloader mode, but you can flash from this screen!). go to G4.3
G4.3 Download wizard_love rom and flash it to your device. Your device should startup again after doing this. Go to G4.4.
G4.4 Is your device CID-unlocked (note: it's not the same as SIM-unlocked!)? YES... go to step G4.7, NO OR DON'T KNOW go to step G4.5. (note: CID-unlocking a G4 is only possible by paying for it at imei-check!)
G4.5 Download enable-rapi.zip. Transfer Cert_SPCS.cab and EnableRapi.cab to your phone. Run Cert_SPCS.cab FIRST and EnableRapi.cab SECOND. Turn your device off and on or wait 5 minutes before soft resetting. Done? Go to G4.6.
G4.6 Follow this great thread by the-equinoxe: [solution] G4 SoftSPL Flash any ROM to CID locked G4 [UPDATED] and load the softSPL on your device using his method. Make sure you take a G4 safe rom (see the thread for details). After the steps you'll have the rom of your choise on your device!
G4.7 You're reade to flash the AKU2, AKU3, WM6 rom of you're choise IF the rom DOESN'T contain IPL/SPL. AKU3 and WM6 roms normally don't contain IPL/SPL. If you want to flash an AKU2 rom, make sure you take the G4 version. If you get an error 300 (invalid update tool) while trying to flash your device look at this thread!
NOTE: If you tried to flash a G3 rom with IPL/SPL in the rom on a G4 you probably will have a bricked device! DON'T flash the new 3.08 and 3.09 IPL/SPL to your G4!
NOTE2: If you got problems flashing with softSPL: Follow this great thread by mun_rus: Solutuion found: how to flash any rom to CIDLOCKED DEVICE. If your device won't start after flashing you can use step G4.2 and G4.3 and try again. Also look at this thread by eddieitman: Faria G4 Step by step installer with instructions to make sure you did all the necessary steps!
Nice one.
One thing I've found is since the Mods split the WM6 stuff to a seperate forum a lot of noobs are in that forum and they don't see the stickies over here now (I've had a couple PM me directly asking where this Wizard Upgrading forum is at that I refer to in my posts ). So I think we need some stickies like this or something in the WM6 forum (or a sticky at the top of that forum with a pointer to this forum and maybe certain posts over here).
Nice. Maybe we should add a link in the Wiki to this...
--M
Corrected the links to wizard_love.... they didn't work.
I found this solution much better than shelltool for flashing my G4 CID-locked Wizard:
http://forum.xda-developers.com/showthread.php?t=271043
Shelltool can only flash the OS while using this modified RUU you can task the OS, splash screen, and the radio. Plus this modified RUU will also flash Wizards that do not bootup normally.
You can't flash a touched OS that way in a CID-locked G4.... only some 2.26 roms will work. Trying this with WM6 will go to 100%, but you're "old" OS will startup again.
Say i downgrade my phone to the T-mobile ROM but have a cingular phone...do i need to have my phone SIM unlocked to use it or since i changed ROMS it doesn't matter...
JBLaze407 said:
Say i downgrade my phone to the T-mobile ROM but have a cingular phone...do i need to have my phone SIM unlocked to use it or since i changed ROMS it doesn't matter...
Click to expand...
Click to collapse
SIM Unlocking only allows you to use SIMs from a different carrier on your phone.
CID Unlocking allows you to flash different Carrier / Country roms on your phone.
If you are only CID Unlocked, you can flash Tmobile, Cingular, Qtek, etc on your phone, but your device will still connect to the same carrier that your SIM is setup for. So for me, I'm on Cingular. I flashed the TMobile 2.26 ROM and I have the complete TMobile look and feel, but my carrier and phone connection was still Cingular since thats what the SIM is for.
I always flash the TMobile 2.26 rom on my phone now before upgrading to a new custom ROM. Its more stable (IMO) than the CIngular 2.25 (at least numerous issues I used to have went away by doing this, but then the custom ROM may be really fixing that, but I like having the latest IPL/SPL for my base).
As always... YMMV
mfrazzz said:
SIM Unlocking only allows you to use SIMs from a different carrier on your phone.
CID Unlocking allows you to flash different Carrier / Country roms on your phone.
If you are only CID Unlocked, you can flash Tmobile, Cingular, Qtek, etc on your phone, but your device will still connect to the same carrier that your SIM is setup for. So for me, I'm on Cingular. I flashed the TMobile 2.26 ROM and I have the complete TMobile look and feel, but my carrier and phone connection was still Cingular since thats what the SIM is for.
I always flash the TMobile 2.26 rom on my phone now before upgrading to a new custom ROM. Its more stable (IMO) than the CIngular 2.25 (at least numerous issues I used to have went away by doing this, but then the custom ROM may be really fixing that, but I like having the latest IPL/SPL for my base).
As always... YMMV
Click to expand...
Click to collapse
Thany you very much for the info...
nice work....stiky.....
could someone post the above info in wiki..... so we can redirect questions to wiki.
If I have CID-unlocked G3 T-Mobile Wizard with custom WM5 ROM installed .... why do I need to downgrade to T-Mobile 2.26 ROM before going to WM6 ?
bogdatov said:
If I have CID-unlocked G3 T-Mobile Wizard with custom WM5 ROM installed .... why do I need to downgrade to T-Mobile 2.26 ROM before going to WM6 ?
Click to expand...
Click to collapse
Good question.... have you flashed T-Mobile rom before? If you haven't you will get the strong 2.26 IPL/SPL. It prevents many problems! This step is to prevent people to upgrade to WM6 with other IPL/SPL!
bogdatov said:
If I have CID-unlocked G3 T-Mobile Wizard with custom WM5 ROM installed .... why do I need to downgrade to T-Mobile 2.26 ROM before going to WM6 ?
Click to expand...
Click to collapse
You want to downgrade so that it cleans up things that are possibly left from a previous install. The Official ROMs have everything (IPL / SPL / OS / Radio / Extended ROM / etc). If you go straight from a custom rom to another custom rom you may find you have stuff left over because the new custom rom doesn't clean up everything. I've seen where things are left in the message queue, so you start getting pop errors about not finding something when that was on the previous ROM.
While it takes extra time, flashing back to an official rom gives you a clean base for the custom rom to work off of. Well worth it for me so I always do this. Takes an extra 15 mins or so, which is better than wasting a day chasing some issue that wouldn't have been there.
BTW: Congrats on getting your post promoted to a Sticky!
mfrazzz said:
You want to downgrade so that it cleans up things that are possibly left from a previous install. The Official ROMs have everything (IPL / SPL / OS / Radio / Extended ROM / etc). If you go straight from a custom rom to another custom rom you may find you have stuff left over because the new custom rom doesn't clean up everything. I've seen where things are left in the message queue, so you start getting pop errors about not finding something when that was on the previous ROM.
While it takes extra time, flashing back to an official rom gives you a clean base for the custom rom to work off of. Well worth it for me so I always do this. Takes an extra 15 mins or so, which is better than wasting a day chasing some issue that wouldn't have been there.
BTW: Congrats on getting your post promoted to a Sticky!
Click to expand...
Click to collapse
Is it also recommended that a downgrade to T-Mobile 2.26 is followed for unlocked G4 phones?
pdagenius said:
Is it also recommended that a downgrade to T-Mobile 2.26 is followed for unlocked G4 phones?
Click to expand...
Click to collapse
Good question. I don't have a G4, but I'd think the same would hold true to get a stable / clean base for the new custom rom.
pdagenius said:
Is it also recommended that a downgrade to T-Mobile 2.26 is followed for unlocked G4 phones?
Click to expand...
Click to collapse
NO! that rom has IPL/SPL in it. Don't try flashing this rom onto a G4! It could brick your device!
thanx a lot !
Great job vippie!
I've updated my thread to reference this.
Please update the first post
Hi Vippie,
Can you please update the first post so that when you tell people to get to the bootloader screen that Activesync will NOT connect, but if it says USB above the left softkey that it is connected? This is something I've had to tell people over and over. People see that activesync doesn't connect so they stop and don't go any further.
Thanks! And again, excellent work on this guide. I'm pointing people to this now as I like how its laid out and gives G3 and G4 info in one place (since so many newbies don't think its important to tell us what they have or anything)
BTW: Has this been put into the Wiki?
mfrazzz said:
Hi Vippie,
Can you please update the first post so that when you tell people to get to the bootloader screen that Activesync will NOT connect, but if it says USB above the left softkey that it is connected? This is something I've had to tell people over and over. People see that activesync doesn't connect so they stop and don't go any further.
Thanks! And again, excellent work on this guide. I'm pointing people to this now as I like how its laid out and gives G3 and G4 info in one place (since so many newbies don't think its important to tell us what they have or anything)
BTW: Has this been put into the Wiki?
Click to expand...
Click to collapse
Good one.... updated the starting post! Thnx!
Uhh......yea......I was trying to upgrade my Rom to Dutty's Diamond V1 Build 19588. I was using the instructions from Flash-Your-Tilt . I got to Step 4 CID-Unlock it installed 100% rebooted and then nothing. Now the phone will only play the intro with no sound, then go black. It shows in the lower right hand R 1.70.02iNex, G25.65.30, D1.62.00.00. The phone will allow me to do a hard reset but after it it goes through the intro with screen alignment and installs the extra apps, it reboots and then goes black. I did a ton of reading through the wiki's if someone could point me in the right direction or tell me if its toast, it would be much appreciated.
Thanks
Be strong. I think it's only bricked when you can't power it on.
I have a poor net connection and not time atm. So a suggestion if you haven't already, search the forum for the word bricked. I'm sure this has happened before..
There are several tricks that people know so you might be ok. good luck.
Calihoe said:
Uhh......yea......I was trying to upgrade my Rom to Dutty's Diamond V1 Build 19588. I was using the instructions from Flash-Your-Tilt . I got to Step 4 CID-Unlock it installed 100% rebooted and then nothing. Now the phone will only play the intro with no sound, then go black. It shows in the lower right hand R 1.70.02iNex, G25.65.30, D1.62.00.00. The phone will allow me to do a hard reset but after it it goes through the intro with screen alignment and installs the extra apps, it reboots and then goes black. I did a ton of reading through the wiki's if someone could point me in the right direction or tell me if its toast, it would be much appreciated.
Thanks
Click to expand...
Click to collapse
Flash an OEM Rom/Radio Combo. Also it wont hurt if you already CID unlocked to to go ahead and flash a new SPL to it. Should fix any and all issues as your phone is still actually booting and Not bricked
Installing windows the 6.1 ROM from HTC's site worked. Thank you very much for the great advice. If I wanted to now put Dutty's ROM on my phone can I go straight to that, or do I need to restart the whole ROM flashing process(installing Jump SPL, Hard SPL and CID) ?
If you have unlocked it, just put duttys onto the SD card and rename the .nbh to KAISIMG.nbh
Put the phone into bootloader and install Its the fastest most successful method. No worry about a data cable coming out mid flash ( happened once to me....not fun )
Shouldnt have to install hardspl again ( or use JumpSPL )
Just make sure that if you are installing a WM6.0 rom that you have a WM6.0 radio. If not, the flashing process for the radio is the same ( rename to KAISIMG.nbh )
Is there a way to see if I the hard SPL install and CID unlock worked ? Can I just restart the whole process regardless. Sorry for the noob questions.
Calihoe said:
Is there a way to see if I the hard SPL install and CID unlock worked ? Can I just restart the whole process regardless. Sorry for the noob questions.
Click to expand...
Click to collapse
Go into bootloader. If your screen says hardspl somewhere near the top then you're good to go. Check which version because you can have radio problems if you use a WM6.0 spl with a WM6.1 rom. Most recent roms are WM6.1 so try HardSPL 3.29 or higher.
If you don't have hardspl, get it here for wm6.0 roms or here for wm6.1 roms.
many thanks, your advice with the links were invaluable. I read and read and read, but i guess i did not read enough. This site rocks.
To all,
I had the 1.14 spl olinex and installed the new 1.56.00.00 release of original italian rom.
I had the green screen as everyone knows, so I installed again the spl from original htc (not the unsigned).
Than my phone always starts with the bootloader and doesn't go on. Giving upgrade rom error.
Please help me!!!!!!!!!!
Pietrona said:
To all,
I had the 1.14 spl olinex and installed the new 1.56.00.00 release of original italian rom.
I had the green screen as everyone knows, so I installed again the spl from original htc (not the unsigned).
Than my phone always starts with the bootloader and doesn't go on. Giving upgrade rom error.
Please help me!!!!!!!!!!
Click to expand...
Click to collapse
Flash your stock ROM via the bootloader.
upgrade your rom using BLACIMG.nbh <-- stock ROM.
make sure you choose a MicroSD that you know it works for sure (like sandisk).
that's no brick yet.
copy your ROM file and rename to BLACIMG.nbh and save it in the root directory of your storage card. Plug it in to the phone again and hold VolDn + press Power button to start the flashing process.
If it's really bricked you wouldn't even able to see the SPL splash screen...
THANKS
Dear all,
great persons......you are.
Thanks for answers, but after 3 hours getting crazy I downloaded the original rom and everything goes right............
Thanks all
hehe you wana sell that brick?
This is my first post
Ok i want to flash my phone for the first time and want to know if all my info is correct.
I want to flash my phone from the stock rom to the WM6.5 pure rom because my battery sucks and so does my signal, any idea if this will work for me???
heres the info i have:
" *** Flash X1 without PC - Micro SD Method ***
This is useful if you load a bad image and cannot make an activesync connection for RUU flashing method.
This method works for any 6.1 and 6.5, and even radio rom.
*** Some Kingston brand may have problem to use SD method, no solution other than use RUU method ***
0. Make sure x1 is hard-spl first
1. Make sure yr micro-sd is formatted w/ fat-32
2. rename the image file (normally "ruu_signed.nbh") to Kovsimg.nbh, copy that to the micro-sd,
and put that it yr X1
3. Make sure X1 is disconnect to your PC to avoid goes to serial mode (AC power source is OK)
4. Bring x1 to boot-loader mode by turning off the x1 completely. Hold the "volume down" button on the right,
and hold the power on button until you see the tri-color screen.
5. Then follow the on-screen instruction
-------------------------------------------------------------------------------------------------------------------
WM 6.5 ---> http://aerohornet.com/xperia/SEX1-R5.04_PURE.rar
BUG FIXING SUPPORT
*Voice Command is included, but disabled by default. To enable it, download and install
THIS CAB (ROM SEX1 R5.07 VoiceCommand).
This will enable the bluetooth audio gateway too (thanks to a1234567 for posting the registry settings)
*Common WM6.5 glitches: a) Tapping taskbar battery icon does nothing b) scrolling dialer with keypad hidden
causes display corruption
add ons ----> http://forum.xda-developers.com/showpost.php?p=3701695&postcount=2 "
Am i on the right track and is it recommendend i do this ?
First of all, update to official R3-rom via SE update service.
There you will get a new radio (signal strength).
After that, Hard-SPL your phone.
When that's done, yes, you can use the Micro SD method.
thanks a milllion so if u upgrade to this rom first like this is it ok ???
"1. download this: http://rapidshare.com/files/238466530/APP_SW_X1i_GENERIC_UK_CDF1215-1832_KOV_R3AA010.exe then
2. rename the image file (normally "ruu_signed.nbh") to Kovsimg.nbh, copy that to the micro-sd,
and put that it yr X1
3. Make sure X1 is disconnect to your PC to avoid goes to serial mode (AC power source is OK)
4. Bring x1 to boot-loader mode by turning off the x1 completely. Hold the "volume down" button on the right,
and hold the power on button until you see the tri-color screen.
5. Then follow the on-screen instruction"
because that is the R3 rom right ?
Just follow your instructions and flash to gtrab ROM first. then if your reception or battery doesnt increase, you can flash to a different radio version. The way to flash to a different radio version is the same method as ROM but u need to find the radio file. The radio file is also in the ROM developement section, all you need to do is search. I think the lastest radio file is 1.16 or 1.17. Good luck. Just post any questions and people will gladly help you.
PS: Once u start to flash different rom, it is addicting to try to different rom. Dont ask which rom is the best, every ROM has it positive and negative. YOu just got to try them all to see which one fit you the best.
so i downloaded the 1.16 radio and...
"Just extracted from new Korean R3BA015 Rom
http://rapidshare.com/files/25077333...1_16_25_48.zip"
did it this method!
"1. just copy the file *.nbh into the root directory of SD card and rename into kovsimg.nbh
2. Do the ordinary flashing (hold the bottom volume button and the power button until the flash screen appear)
3. Follow the next instruction"
its saying loading for 5 mins now , is this normal???
ok i never hard spl it first i think that might be the problem
im having a huge problem hard spl my phone can someone please guide me step by step thanks
1. State problem
2. Follow this for HardSPL'ing http://forum.xda-developers.com/showthread.php?t=431218
dogans said:
First of all, update to official R3-rom via SE update service.
There you will get a new radio (signal strength).
After that, Hard-SPL your phone.
When that's done, yes, you can use the Micro SD method.
Click to expand...
Click to collapse
Havent you read the posts???He clearly mentioned you to Hard SPL first...It is the most important step in ROM flashing...You can even brick your phone if you dont do this step...
Contact me if you want assistance: Y!MSgr id: [email protected]
oh yes it did it this things tricky cos it gave me connection errors like 10 times before it worked now to install the radio n then the 6.5 pure rom i will install tomorrow thanks a million guys will let u know if i get stuck again lol
thanks a million my radio rom works 100% will be back tomorrow btw did anyone experience a rom with great battery life if you have please post the link
this is also a great rom with no hick ups.
borg28 said:
this is also a great rom with no hick ups.
Click to expand...
Click to collapse
which rom are u refering to and please provide a link thanks
SEX1-R5.04_PURE is working 100% and its gr8 , i wanna thank everyone for helpine me n if u even need application recommendations please let me know i am also here to help and now so can i help with flashing THANKS A MILLION
i cant c my sms's on SEX1-R5.04_PURE and it has no fixes help someone
seems like it was a unfixed bug in the roms of most 6.5's so i then flashed to the UnOff rom n it seems to be working gr8 so far thanks everyone!