This guide was written a long time ago. I recommend people to use this more up to date guide:
Wizard Windows Mobile 6 for newbies
I've got a lot of post behind my name, but most of my posts are answers to the same questions over and over again. It seems very hard for "noobs" to find the answer to their question quickly on the forum. I quickly wrote a little step by step tutorial for them. Hope it helps!
Suggestions or corrections are always welcome.
You want to flash your wizard, but don't know where to start. Try this:
0. First determine if you got a G3 or a G4 device. When you turn on your device from can can see you're IPL and SPL version on the screen. If you got IPL/SPL 1.xx or 2.xx you've got a G3 device. If the IPL/SPL shows 2.xx.xxx1 you've got a G4. Go to step G3.1 if you got a G3 and G4.1 if G4.
G3.1 Does you're device start normally (yes) or is it stuck on the three-colored bootloader screen (no)? YES... go to step G3.5, NO go to step G3.2
G3.2 Turn off you're device totaly. Remove the SD card and disconnect the USB cable from you're device. Turn on the device while holding the camera button. You will get into bootloader mode (3 colored screen). Connect the USB cable to the computer and you will see USB at the bottom of your screen above the left softkey (Activesync will not connect in bootloader mode, but you can flash from this screen!). If you got IPL/SPL 1.xx go to G3.3. If you got 2.xx go to G3.4
G3.3 Download button rom and flash it to your device. Your device should startup again after doing this. Go to G3.5.
G3.4 Download wizard_love rom and flash it to your device. Your device should startup again after doing this. Go to G3.5.
G3.5 Is your device CID-unlocked (note: it's not the same as SIM-unlocked!)? YES... go to step G3.7, NO OR DON'T KNOW go to step G3.6.
G3.6 Follow this great thread by Dr Puttingham: The Definitive Guide to Unlocking & Rom Upgrading G3 Wizards. Don't skip step 17! Flash the T-Mobile 2.26 Rom! Go to step G3.8 if you got the T-Mobile rom with IPL/SPL 2.26 on your device after doing this.
NOTE: Some people seem to have problem with flashing the button rom in this step (stops at 98% with error 302). Replace button_rom with Xda_MiniS_LaunchROM_v154102 and follow the rest of the steps normally when this happens!
G3.7 Download T-Mobile 2.26 rom and flash it to your device! Done? Go to step G3.8.
G3.8 You're reade to flash the AKU2, AKU3, WM6 rom of you're choise! It wasn't that hard, was it? If you still got an older OS version after flashing then you're not CID-unlocked! Go back to start!
------------------------------------
G4.1 Does you're device start normally (yes) or is it stuck on the three-colored bootloader screen (no)? YES... go to step G4.4, NO go to step G4.2
G4.2 Turn off you're device totaly. Remove the SD card and disconnect the USB cable from you're device. Turn on the device while holding the camera button. You will get into bootloader mode (3 colored screen). Connect the USB cable to the computer and you will see USB at the bottom of your screen above the left softkey (Activesync will not connect in bootloader mode, but you can flash from this screen!). go to G4.3
G4.3 Download wizard_love rom and flash it to your device. Your device should startup again after doing this. Go to G4.4.
G4.4 Is your device CID-unlocked (note: it's not the same as SIM-unlocked!)? YES... go to step G4.7, NO OR DON'T KNOW go to step G4.5. (note: CID-unlocking a G4 is only possible by paying for it at imei-check!)
G4.5 Download enable-rapi.zip. Transfer Cert_SPCS.cab and EnableRapi.cab to your phone. Run Cert_SPCS.cab FIRST and EnableRapi.cab SECOND. Turn your device off and on or wait 5 minutes before soft resetting. Done? Go to G4.6.
G4.6 Follow this great thread by the-equinoxe: [solution] G4 SoftSPL Flash any ROM to CID locked G4 [UPDATED] and load the softSPL on your device using his method. Make sure you take a G4 safe rom (see the thread for details). After the steps you'll have the rom of your choise on your device!
G4.7 You're reade to flash the AKU2, AKU3, WM6 rom of you're choise IF the rom DOESN'T contain IPL/SPL. AKU3 and WM6 roms normally don't contain IPL/SPL. If you want to flash an AKU2 rom, make sure you take the G4 version. If you get an error 300 (invalid update tool) while trying to flash your device look at this thread!
NOTE: If you tried to flash a G3 rom with IPL/SPL in the rom on a G4 you probably will have a bricked device! DON'T flash the new 3.08 and 3.09 IPL/SPL to your G4!
NOTE2: If you got problems flashing with softSPL: Follow this great thread by mun_rus: Solutuion found: how to flash any rom to CIDLOCKED DEVICE. If your device won't start after flashing you can use step G4.2 and G4.3 and try again. Also look at this thread by eddieitman: Faria G4 Step by step installer with instructions to make sure you did all the necessary steps!
Nice one.
One thing I've found is since the Mods split the WM6 stuff to a seperate forum a lot of noobs are in that forum and they don't see the stickies over here now (I've had a couple PM me directly asking where this Wizard Upgrading forum is at that I refer to in my posts ). So I think we need some stickies like this or something in the WM6 forum (or a sticky at the top of that forum with a pointer to this forum and maybe certain posts over here).
Nice. Maybe we should add a link in the Wiki to this...
--M
Corrected the links to wizard_love.... they didn't work.
I found this solution much better than shelltool for flashing my G4 CID-locked Wizard:
http://forum.xda-developers.com/showthread.php?t=271043
Shelltool can only flash the OS while using this modified RUU you can task the OS, splash screen, and the radio. Plus this modified RUU will also flash Wizards that do not bootup normally.
You can't flash a touched OS that way in a CID-locked G4.... only some 2.26 roms will work. Trying this with WM6 will go to 100%, but you're "old" OS will startup again.
Say i downgrade my phone to the T-mobile ROM but have a cingular phone...do i need to have my phone SIM unlocked to use it or since i changed ROMS it doesn't matter...
JBLaze407 said:
Say i downgrade my phone to the T-mobile ROM but have a cingular phone...do i need to have my phone SIM unlocked to use it or since i changed ROMS it doesn't matter...
Click to expand...
Click to collapse
SIM Unlocking only allows you to use SIMs from a different carrier on your phone.
CID Unlocking allows you to flash different Carrier / Country roms on your phone.
If you are only CID Unlocked, you can flash Tmobile, Cingular, Qtek, etc on your phone, but your device will still connect to the same carrier that your SIM is setup for. So for me, I'm on Cingular. I flashed the TMobile 2.26 ROM and I have the complete TMobile look and feel, but my carrier and phone connection was still Cingular since thats what the SIM is for.
I always flash the TMobile 2.26 rom on my phone now before upgrading to a new custom ROM. Its more stable (IMO) than the CIngular 2.25 (at least numerous issues I used to have went away by doing this, but then the custom ROM may be really fixing that, but I like having the latest IPL/SPL for my base).
As always... YMMV
mfrazzz said:
SIM Unlocking only allows you to use SIMs from a different carrier on your phone.
CID Unlocking allows you to flash different Carrier / Country roms on your phone.
If you are only CID Unlocked, you can flash Tmobile, Cingular, Qtek, etc on your phone, but your device will still connect to the same carrier that your SIM is setup for. So for me, I'm on Cingular. I flashed the TMobile 2.26 ROM and I have the complete TMobile look and feel, but my carrier and phone connection was still Cingular since thats what the SIM is for.
I always flash the TMobile 2.26 rom on my phone now before upgrading to a new custom ROM. Its more stable (IMO) than the CIngular 2.25 (at least numerous issues I used to have went away by doing this, but then the custom ROM may be really fixing that, but I like having the latest IPL/SPL for my base).
As always... YMMV
Click to expand...
Click to collapse
Thany you very much for the info...
nice work....stiky.....
could someone post the above info in wiki..... so we can redirect questions to wiki.
If I have CID-unlocked G3 T-Mobile Wizard with custom WM5 ROM installed .... why do I need to downgrade to T-Mobile 2.26 ROM before going to WM6 ?
bogdatov said:
If I have CID-unlocked G3 T-Mobile Wizard with custom WM5 ROM installed .... why do I need to downgrade to T-Mobile 2.26 ROM before going to WM6 ?
Click to expand...
Click to collapse
Good question.... have you flashed T-Mobile rom before? If you haven't you will get the strong 2.26 IPL/SPL. It prevents many problems! This step is to prevent people to upgrade to WM6 with other IPL/SPL!
bogdatov said:
If I have CID-unlocked G3 T-Mobile Wizard with custom WM5 ROM installed .... why do I need to downgrade to T-Mobile 2.26 ROM before going to WM6 ?
Click to expand...
Click to collapse
You want to downgrade so that it cleans up things that are possibly left from a previous install. The Official ROMs have everything (IPL / SPL / OS / Radio / Extended ROM / etc). If you go straight from a custom rom to another custom rom you may find you have stuff left over because the new custom rom doesn't clean up everything. I've seen where things are left in the message queue, so you start getting pop errors about not finding something when that was on the previous ROM.
While it takes extra time, flashing back to an official rom gives you a clean base for the custom rom to work off of. Well worth it for me so I always do this. Takes an extra 15 mins or so, which is better than wasting a day chasing some issue that wouldn't have been there.
BTW: Congrats on getting your post promoted to a Sticky!
mfrazzz said:
You want to downgrade so that it cleans up things that are possibly left from a previous install. The Official ROMs have everything (IPL / SPL / OS / Radio / Extended ROM / etc). If you go straight from a custom rom to another custom rom you may find you have stuff left over because the new custom rom doesn't clean up everything. I've seen where things are left in the message queue, so you start getting pop errors about not finding something when that was on the previous ROM.
While it takes extra time, flashing back to an official rom gives you a clean base for the custom rom to work off of. Well worth it for me so I always do this. Takes an extra 15 mins or so, which is better than wasting a day chasing some issue that wouldn't have been there.
BTW: Congrats on getting your post promoted to a Sticky!
Click to expand...
Click to collapse
Is it also recommended that a downgrade to T-Mobile 2.26 is followed for unlocked G4 phones?
pdagenius said:
Is it also recommended that a downgrade to T-Mobile 2.26 is followed for unlocked G4 phones?
Click to expand...
Click to collapse
Good question. I don't have a G4, but I'd think the same would hold true to get a stable / clean base for the new custom rom.
pdagenius said:
Is it also recommended that a downgrade to T-Mobile 2.26 is followed for unlocked G4 phones?
Click to expand...
Click to collapse
NO! that rom has IPL/SPL in it. Don't try flashing this rom onto a G4! It could brick your device!
thanx a lot !
Great job vippie!
I've updated my thread to reference this.
Please update the first post
Hi Vippie,
Can you please update the first post so that when you tell people to get to the bootloader screen that Activesync will NOT connect, but if it says USB above the left softkey that it is connected? This is something I've had to tell people over and over. People see that activesync doesn't connect so they stop and don't go any further.
Thanks! And again, excellent work on this guide. I'm pointing people to this now as I like how its laid out and gives G3 and G4 info in one place (since so many newbies don't think its important to tell us what they have or anything)
BTW: Has this been put into the Wiki?
mfrazzz said:
Hi Vippie,
Can you please update the first post so that when you tell people to get to the bootloader screen that Activesync will NOT connect, but if it says USB above the left softkey that it is connected? This is something I've had to tell people over and over. People see that activesync doesn't connect so they stop and don't go any further.
Thanks! And again, excellent work on this guide. I'm pointing people to this now as I like how its laid out and gives G3 and G4 info in one place (since so many newbies don't think its important to tell us what they have or anything)
BTW: Has this been put into the Wiki?
Click to expand...
Click to collapse
Good one.... updated the starting post! Thnx!
Related
I have a newly bought Cingular 8125 in India. I would love to Upgrade that.
Though the box says it is for UK, I can use with the service providers in India.
I assume it is unlocked already.(is it really?)
This is my device information at boot:-
IPL: 2.25
SPL: 2.25
GSM: 02.25.11
OS: 2.25.11.1
I am planning to use Molsky.Biz ROM available here:-
RUU_Molski.Biz_226102_22610105_022511_WWE (G3 Device. IPL/SPL like: 2.xx)
I hope my device is G3.
Do I need to CIDUnlock my device? What is the FullUnlock?
Molsky.Biz says:-
" Also DO NOT FORGET to CID UNLOCK your Wizard. This is only possible with LokiWiz 0.2b and
IPL/SPL 1.xx, if you have a CID LOCKED Wizard with IPL/SPL 2.xx.0001 flash a G4 Rom !! "
But My IPL/SPL is not 1.xx as you can see above in my details.
What should I do to unlock? Do I need to do that at all?
and what is meant by AKU? Do I need that?
I sold my nokia and communicator to buy this phone. So dont want to brick it because of my ignorance!
Please guide me.
Many Thanks.
Read this thread and follow it
http://forum.xda-developers.com/showthread.php?t=263116
Your phone is a G3. If the IPL and SPL has more than 2 digits after the first decimal (ie: 2.xx.xx) then it's a G4.
As for unlocking, that confuses the bejesus out of me.
I would say download the G3 ROM, figure out how to unlock your phone (if possible) and then you should be good to go.
You SHOULD be scared given all the threads around here from people who trashed their phones. And I'd bet few of them could give a straight answer as to why they wanted to do so in the first place. So before you do anything, define why you want to update the rom. Does it do something specific that you absolutely can't live without and makes it worth the risk of ruining the phone? Maybe a custom rom is a tiny bit faster but in a day's time, will it make any difference? Probably not, and an operator rom that's a tiny bit slower is still a LOT faster than a dead phone. Don't forget that the moment you start flashing with anything but an operator approved rom, you're out of warrantee. if you absolutely MUST update the rom, then start reading the link above. Every question you asked has already been answered here many, many times. Is your phone a G3 or a G4? Better know BEFORE you start. Oops...you're at 55% and your PC crashes...what do you do? Better know BEFORE you start. The phone reboots and won't go past the splash screen, what do you do now? Better know BEFORE you start.
Thank you all for the replies.
The main reason for flashing it to the new rom was speed and space considerations.
I was owning an XDA Mini earlier and successfully did the BigStorage and Rom updates.
But seeing many users bricking their wizard here and being not sure about the 'unlocking thing' i've decided to atleast not to venture into the bleeding edge atleast during my warranty period.
I know many questions might have been answered many a times, but the answers too are very contextual, they are different for different versions / models etc.
Hopefully I will do it sometime next year!
i would vote the warranty period is the best time to do it.. then you can tell your provider you tried to update their rom and now your phone dont work and let them send you a replacement...
Flashing isnt all that scary, the first time its a little nerve racking, but then again i like living on the edge...
So if your gonna do it, here is a quick simple explanation...
Downgrade to a 1.xx rom from the FTP site, after the your IPL/SPL should show 1.xx during boot up (mine actually differed, had IPL 1.xx SPL 2.xx and still unlocked just fine, some people claim to have issues though)
after successfully booting run lokwiz 2b (its the one i used) do the sim and supercid unlock.
Then reflash a stock 2.xx rom so that you are sure to get the updated bootloaders, after that has completed successfully then flash any rom you want..
its that simple, just a little time consuming
How to copy the cab file(enable rapi) to your device and run it before running lokiwi
Please disreegard below. Just found it.
Thanks..
I am kind of new in this.
I want to unlock the device but do not know how to
copy the cab file(enable rapi) to your device and run it before running lokiwiz.
I will appreciate your help on this so I can continue with the upgrades.
Thanks in Advance.
1 - Unzip lokiwiz02b.zip to somewhere (extract to c:\lokiwiz) in your computer
2. Connect your phone via ActiveSync to your PC . Browse your phone with File Explorer from your PC.
3 - Copy EnableRapi.cab to your Wizard (My Document)
4 - Execute the EnableRapi.cab in your phone. Wait for it to finish
5 - Guarantee that your phone is connected via activesync with the computer
6 - Execute lokiwiz.bat (from your computer run c:\lokiwiz\lokiwiz.bat, double click on that file) and follow the instructions on your screen...
7 - Select Option U to unlock your Wiz.
Hi, After the soft reset comand, I removed the battery from my Wizard. After that the followin problem was appear: the phone is bringing up to the splash screen and STOP on this position.I have tried to download another Rom but the problem still is the same. My Phone is not CID unlock and before this, I cooked own rom like is writen here http://forum.xda-developers.com/showthread.php?t=271043 . So any idea how to wake-up my phone MDA Vario.
Ok forgive me if I'm wrong here, I don't really want to judge before I know the full story, but seems to me your brain went on strike momentarily. First rule of flashing any unofficial rom CID UNLOCK YOUR DEVICE. Anyways sorry, I just wanted to say something so it doesn't happen to you again, that said, what rom did you try to upgrade to? what rom did you try to downgrade to after that? is your device a G3 or G4?
If your device is a G3 I would recommend downgrading to this rom by xelecin
ftp://xda:[email protected]_RUU_Wizard_1081002_108_10910_ENG_US.exe
it will ask you if you want to CID unlock your device at the start so you shouldn't need to worry about forgetting this time , if you can't connect your device to activesync just go into the bootloader (hold the camera, voice dial buttons while pressing the reset button) and once it connects run the set-up.
Oh another thing before I forget..... do some searching and read up a bit, because this is a pretty common topic on this forum, best of luck and hope everything works out ok. If not, report back.
*edit* I just noticed the thread that you linked to, I actually wasn't aware that this was possible, but anyways I think it's still much safer to CID unlock your device if possible, and another thing you might try replying in that thread if it doesn't work out since they should be more knowledgeable in the matter..... and that would help keep the forums less cluttered *edit*
Thanks, for your help, Unfortunately you are totaly right for my stupid act (again). At first i tried to solve the problem alone , but whole day I roam through this forum to find solution but I can't find the same problem like my. Maybe because of my ..... brain .Anyway I am with G3. NOW I have
IPL 1.0
SPL 2.26
GSM 01.09.11
OS 1.5.4.2
This is after this procedure http://forum.xda-developers.com/showthread.php?t=263116
I tried also to download also and Molski's 2.26.10.2 AKU2.3 Rom a.k.a. 2.26.10.2 Final Edition Rom, but the problem is the same : The splash screen is running and STOP and.... nothing.
I can go to bootloader and can download new rom, but I can't start fhe phone.
Yeah I know these forums aren't the easiest in which to look for info. So you can go into the bootloader, that's good. Don't try to go to a AKU2.x rom or later, keep it under that, so no 2.26 roms at all. 105, or 108 roms should be good.
Did you try the rom from the link I provided or the one on the thread? and afterwards did it go into the phone at all? My friends MDA had a similar problem last week, caused by the same thing, though in your case I see the SPL isn't updating when you install new roms on his it was the os that wasn't updating, but as soon as I installed that rom I recommended it booted up fine, then I updated his device to molski's 2.3.
I'll check back in a few so let me know how's it going.
Here's what you need to know & if you follow these instructions your prob will be solved.
The Definitive Guide to Unlocking & Rom Upgrading G3 Wizards
http://forum.xda-developers.com/showthread.php?t=285435
Wish u best of luck.
DoCtOr_X said:
Here's what you need to know & if you follow these instructions your prob will be solved.
The Definitive Guide to Unlocking & Rom Upgrading G3 Wizards
http://forum.xda-developers.com/showthread.php?t=285435
Wish u best of luck.
Click to expand...
Click to collapse
Ok, but tell me how to solve this :
"qiote"
8. Open ActiveSync, Explore and copy enablerapi.cab from your PC's C:\ (remember that's where you extracted lokiwiz to...) to you device, I don't care where.
9. Pick up your PDA, File Explorer, find the enablerapi.cab and click it.
"quote"
I don't have access to the phone explorer and phone at all.
masr1979 I have tried the rom you give me, but it look like there is some things I don't understand: When I start the exe file i have choice <continue> .Whet I type <c> 2(two) time the soft tell me <no device found> and order me to continue with copy ???. After few seconds tell me that Unlocker ..... Done!, and start HTC wizard Unlocker and NOTHING !!! Stop on this position more then 15 min. and only the led for charging on the phone is active.
Forget all about unlocking. Until you can boot the device completely it'll never work.
Try and install an official 2.x ROM on your device.
My suspicion is that you originally has a G4 device, which is bad because if you DID have a G4 you have a brick now...
Can you remember your phones old ipl/spl? for your sake I hope it wasn't something in this format 2.XX.000X.
masr1979 said:
Can you remember your phones old ipl/spl? for your sake I hope it wasn't something in this format 2.XX.000X.
Click to expand...
Click to collapse
Of course I'm not sure, but I thing it was 2.21. Anyway did you think that is posible to cook my own rom in G4? I'm totally confused.
Every time when I upload new rom I have this:
http://forum.xda-developers.com/attachment.php?attachmentid=32884&stc=1&d=1168184491
IMG_2976.jpg
...and also this is my bootloader screen
http://forum.xda-developers.com/attachment.php?attachmentid=32885&stc=1&d=1168184491
IMG_2977.jpg
Dr Puttingham said:
Forget all about unlocking. Until you can boot the device completely it'll never work.
Try and install an official 2.x ROM on your device.
My suspicion is that you originally has a G4 device, which is bad because if you DID have a G4 you have a brick now...
Click to expand...
Click to collapse
Thanks, but I try to find oficial rom but without success. And very interesting thing I found.. when I start to upload new rom the soft start to check my old rom and after that tell me that i have GE (german) language, but my old was WWE ?
Is it posible some one to give me some link to official 2.x ROM but for T-mobile german language.
Well the other day I tried finding that german rom for a while.... that search was going nowhere, I saw this thread, I don't know if you might want to check into it and maybe try it out. There's mixed results apparently but who knows
http://forum.xda-developers.com/showthread.php?t=276963
I was upgrading my t-mobile 8150(?) the k-jam with the new windows mobile 6 and in the middle of it my comp crashed!! now i am stuck at the bootloader mode (3 colored screen) and when i try to redo it i get to 99% and get a 302 error message. i follow the instructions given but keeps going in circles. its a G3 so is my phone bricked or is there a way to save it? i've been looking at this site all day but am now just more confused. lol thanks for your help!
No your phone isn't bricked. As long as you can get into the bootloader screen you should be ok. What you need to do is flash an official carrier rom either tmobile 2.26 or wizard love rom after you that than you can reflash to wm6. look at the stickies in the wizard forums that is where you can find these roms.
Thanks for the info but seems my techno curse continues. I tried the wizard love rom but it was in a different language and whem i tried the tmobile 2.26 i got "error 274 connection." Any more suggestions? Again thanks soo much for an issue I'm sure has been posted here a thouand times.
This happens to me all the time. I always use the Cingular 2.25 rom, it works perfectly and I have an I-mate K-JAM. Then, do the WM6 upgrade, but ensure all of your Norton and Antivirus and background running apps are shut down. Good luck.
yes also take out your mini sd card if you have one. even though its in another language it will work. "AVANTI means next. so just keep hitting that and you will be fine.
hmm been trying to d/l the Cingular 2.25 rom but the link seems to have stoped working...
It;s aaaaaaaaaaaaaaalllllllllliiiiiiiiiiivvvvvvvvvvvvvvvvveeeeeeeeeeeeeeeee!!! for now lol Lets see what happens after i install wm6 I couldn't get the cingular rom but i had already dowbloaded the button rom i found here earlier and it worked like a dream!! quick and easy!! thank you all soooooo much!
hi all. one more little thing. after adding the new rom to get it back to life, now the numbers don't match so i can't upgrade to wm6. i have ipl 1.01 spl 2.26. advice?
flash to the tmo 2.26 or cingular 2.25...that will give you an IPL/SPL of 2.xx
then, you can flash to WM6
i want to delete this message. can't find a way to do it.
there's any other way to flash without usb cable?? sorry to bug in this thread but i lost my usb connection somehow and did a hard reset and still doesn't work. my phone charges. and no is not my computer cuz my wifes phone same as mine does sync i have a tmobile mda also known as the cingular 8125.
fallon75 said:
hi all. one more little thing. after adding the new rom to get it back to life, now the numbers don't match so i can't upgrade to wm6. i have ipl 1.01 spl 2.26. advice?
Click to expand...
Click to collapse
keep reflashing buttons rom until both ipl/spl are the same number. if they are different, then the flash didn't complete correctly. (it happens often, so it's kinda normal). just keep reflashing. after both ipl/spl are the same, then CID unlock and then update to an official carrier...then flash a wm6.
can anyone help me??
Check if "USB" displayed when in bootloader mode (Camera+reset) with Wizard connected to PC.
If so, you may try to flash another ROM through bootloader.
starkwong said:
Check if "USB" displayed when in bootloader mode (Camera+reset) with Wizard connected to PC.
If so, you may try to flash another ROM through bootloader.
Click to expand...
Click to collapse
it does shows but how can i flash?? it still won't connect o my pc. my pc doesn't recognize it. but it does recognize my wifes phone.
Try to run RUU straight with Wizard connected and running in bootloader mode
Hello All Developers,
It's my 1st time yo post a new thread, well thats because i always found the answer in either the subject or the answers. Yet, for problem in hand, I cant find any thread with it included.
I bought a G3 Wizard, and I fell in love with it, this is not new, i fall in love with all my mobiles and PDAs.
I have a Himalaya too which is much more simple than Wizard regarding upgrading. and here we go
I followed the instructions in the sticky thread titled:
[READ FIRST] The Definitive Guide to Unlocking & Rom Upgrading G3 Wizards
I found it very helpful. I followed mainly the FARIA version too, i was reading the 2 threads in parallel to double check my understanding.
it all went great .. till the IPL/SPL upgrade step, i followed my guess that i dont need to go though the 2.26 ROM to update afterwards to 3.08. so i upgraded to 3.08 and all went well.
the next was to upgrade to any WM6.1 versions. and for my sorrow, all of them failed to update.
the failure it self was a piece of art. after the completion of the update taking its 10 mins, it just hard reset my device. no new rom is installed.
my guess was, go back to 1.05 and go to 2.26 instead of 3.08
i did that and found my IPL/SPL changed from 3.08/3.08 to 1.01/3.08 even though the rom is supposed to have both of them equaling 1.05
ignoring this fact "an error i'll regret soon" i tried to upgrade to any WM6.1 ROM and voalla
I BRICKED MY BELOVED WIZARD.
yes thats right, it stuck at 98% and sowed a failure message. allowing me only to follow the recovery steps. and i got this 4 strips screen (i'm counting the white strip too)
any way, after trying with different roms, different uti upgrading file, all reached the point of failure.
so, i kinda lost hope, and removed the batt, the SIM and left the device like this for 4 hours or even more.
i returned from work, and prayed to god to help me. i cant live without my beloved Wizard.
and the only thing i could do was to try to install the button 1.05 rom again. i tried b4 the 4 hours break, and it failed just like the others.
i dont know how but while praying , the mobile continued to flash the rom and booted completely!!!
now, after this story, here is my current status,
IPL/SPL = 1.01/3.08
ROM : button 1.05
additional info: i'm afraid of trying to upgrade to WM6 or WM6.1,may be i get it bricked for life this time!!!!
should i use WST to restore my old IPL/SPL?
what can i do to use WM6 or 6.1?
thanks for taking time to read this thread, i appreciate it
Try to install an official rom from cingular or t-mobile and then try to upgrade to wm6.1
solomhamada said:
Hello All Developers,
It's my 1st time yo post a new thread, well thats because i always found the answer in either the subject or the answers. Yet, for problem in hand, I cant find any thread with it included.
I bought a G3 Wizard, and I fell in love with it, this is not new, i fall in love with all my mobiles and PDAs.
I have a Himalaya too which is much more simple than Wizard regarding upgrading. and here we go
I followed the instructions in the sticky thread titled:
[READ FIRST] The Definitive Guide to Unlocking & Rom Upgrading G3 Wizards
I found it very helpful. I followed mainly the FARIA version too, i was reading the 2 threads in parallel to double check my understanding.
it all went great .. till the IPL/SPL upgrade step, i followed my guess that i dont need to go though the 2.26 ROM to update afterwards to 3.08. so i upgraded to 3.08 and all went well.
the next was to upgrade to any WM6.1 versions. and for my sorrow, all of them failed to update.
the failure it self was a piece of art. after the completion of the update taking its 10 mins, it just hard reset my device. no new rom is installed.
my guess was, go back to 1.05 and go to 2.26 instead of 3.08
i did that and found my IPL/SPL changed from 3.08/3.08 to 1.01/3.08 even though the rom is supposed to have both of them equaling 1.05
ignoring this fact "an error i'll regret soon" i tried to upgrade to any WM6.1 ROM and voalla
I BRICKED MY BELOVED WIZARD.
yes thats right, it stuck at 98% and sowed a failure message. allowing me only to follow the recovery steps. and i got this 4 strips screen (i'm counting the white strip too)
any way, after trying with different roms, different uti upgrading file, all reached the point of failure.
so, i kinda lost hope, and removed the batt, the SIM and left the device like this for 4 hours or even more.
i returned from work, and prayed to god to help me. i cant live without my beloved Wizard.
and the only thing i could do was to try to install the button 1.05 rom again. i tried b4 the 4 hours break, and it failed just like the others.
i dont know how but while praying , the mobile continued to flash the rom and booted completely!!!
now, after this story, here is my current status,
IPL/SPL = 1.01/3.08
ROM : button 1.05
additional info: i'm afraid of trying to upgrade to WM6 or WM6.1,may be i get it bricked for life this time!!!!
should i use WST to restore my old IPL/SPL?
what can i do to use WM6 or 6.1?
thanks for taking time to read this thread, i appreciate it
Click to expand...
Click to collapse
Perhaps! your phone is still CID locked and you upgraded to 3.08,sometimes,while downgrading from 3.08 to 1.xx,spl freezes at 3.08,now try to upgrade back to 3.08 and downgrade first to 2.xx by flashing the official rom and then downgrade to 1.xx.
or,download the latest version of WST 4.2.2 and check the CID lock/unlock status,if its still locked,you can try to CID unlock with WST 4.2.2,its seen,it sometimes performs the CID unlock with different SPL other then 1.xx,atleast one user did report this successful.
ok, im inbetween a newb and a full out destructive force to any type of moddable device and im having a little bit of trouble with my cingular 8125. ive had this phone for a few months and i am having the hardest time dealing with the rom on the phone now. ill give a quick breifing on it:
got it with original cingular rom, not sure what spl or ipl on it but the first thing i did was unlock it by myself, cid and sim unlocked, and then updated to a jaguar wm 6.1 rom which worked fine. decided i was going to unfortunately sell this phone so i decided to upgrade it one more time to see if i really wanted to sell it, i then bought the upgrade to go past my 2.21 ipl and spl. i got my unlocker and followed my instructions and got a brick. but not a full brick. its stuck in the bootloader screen. after reading countless threads, i learned that i should be able to just still update a rom to the phone with no problems which actually works, but as soon as a rom completes it goes right back to my bootloader screen so help me! please cuz now thats its a challenge again, i want the phone! plus all my info is on the phone still back up
Flash the official stock ROM first, then use Button's ROM to downgrade your IPL and SPL before unlocking CID.
post the present IPL/SPL it displays now.Which rom you are trying to flash now ?
ok when i try to put the most current 8125 rom on my phone (2.25.blah) it tells me that its not the same phone which is weird but thats preventing me from putting the original rom on the phone. however if i try and put the buton rom on the phone now, it will go through completely and say it put it on the phone, but when it restart, its right back to the bootload screen...
and im running IPL 2.21.0001 and SPL 2.21 with a previous installation of a jaguar rom, dont know exactly which one, but i know it was a jaguar rom. but right before i tried to upgrade the updater, i went back to my default WM5 rom so i guess it was te basic 2.21 rom on the phone with WM5
dimedash12 said:
ok when i try to put the most current 8125 rom on my phone (2.25.blah) it tells me that its not the same phone which is weird but thats preventing me from putting the original rom on the phone. however if i try and put the buton rom on the phone now, it will go through completely and say it put it on the phone, but when it restart, its right back to the bootload screen...
and im running IPL 2.21.0001 and SPL 2.21 with a previous installation of a jaguar rom, dont know exactly which one, but i know it was a jaguar rom. but right before i tried to upgrade the updater, i went back to my default WM5 rom so i guess it was te basic 2.21 rom on the phone with WM5
Click to expand...
Click to collapse
WEIRD !
You got mixed Bootloaders of G3 And G4,IPL 2.21.0001 is G4 and SPL 2.21 is G3,as you posted,well,can't say which was original,only you can tell,but some how its mixed Bootloaders,in this situation no Rom will flash,its a 'Brick'.
If as Zabardast says its bricked then you have three options:
1. Get a new Wizard
2. Get a new Wizard Motherboard
3. Get a Wizard with broken LCD from eBay and replace its LCD with your current one and Enjoy!!! (Cheapest)
lol this is tough! but no worries, ill be back with some other pda at some point and time and then ill try and take this phone apart! but the weird thing about my wizard is that this only happened when i tried to update the phone with the CID unlock program that you have to pay for!
lol it was perfectly fine until i tried to do it! oh well, back to my crappy p168!
May be that CID Unlock program was not meant to be for a G3 and you were updating a G3 so it mixed you IPL/SPL and caused a kinda BRICK. So please be careful before doing flashing things because if you dont be carefull then your PPC may become a heavy paper weight, and a costy one too. LOL. TC
kitty4uhig said:
Farming for eq2 plat isn't easy, but you can buy eq2 plat, guides, accounts & items on sale. We have revolutionized the exchange of money to eq2 plat. Purchase eq2 plat& power up your character ot the next level. Our world class customer service will make sure you are more than satisfied with every purchase. Feel free to contact our 24 hour live support with any questions you may have. Shop now and play as a VIP!
Click to expand...
Click to collapse
Stop this nonsense immediately,otherwise it'll be reported and you'll be banned.Its spam !!!
try this: http://forum.xda-developers.com/showthread.php?t=276963
Cingular 8125 problems
Ok guys i am really pissed i have been looking for three days and cant find it, first off my IPL is at 1.01 and the SPL is at 2.25 and i cant fix it i wanted to install the original 2.25 again and start from scratch but can not find the damn thing so if anyone has it can u just upload it fo me and give me a link that i can get it at please i am sick and tired of waitnin i really like this phone and i dont want to risk bricking it thanks.
Ok, grimgod, aggression is reaaaallly ugly and no freakin one will help with that sh!t attitude (pardon the language, mods). The senior members do everything they can to help the noobs. Have you tried reading the flashing guide, wiki, or tutorial? I'd bet even money you haven't. Have you CID unlocked? Did you flash the button rom twice ( as the guide suggested to get ipl/spl both 2.xx)? Did you flash the official tmo rom (found im the flashing guide)? Have you done anything other than sit on your hands and wait for it to be handed to you? READ AND SEARCH!!!!!!!!!!!!!!!!
http://forum.xda-developers.com/showthread.php?t=310831 <HERE!!!!!!!!!! Should I flash your device, too?
Similar issue... need some Wizard Expertise
I picked up a coworkers old Cingular 8125 that he'd had in a drawer for about a year. Battery was right dead so the phone wouldn't boot. I charged the battery on an external charger for a few minutes, put it back into the phone, and plugged it in to the charger until the LED went green indicating a full charge.
When I power up I see the T-Mobile splash screen (light gray background, some square dots, and the "T-Mobile" logo). And there it stays indefinitely.
Tried a hard reset (Comm Mgr + Voice Cmd + Soft Reset), and it said "Press Send to restore factory default". Pressed the green dialer key (I assume that's send), and it says Format FAT partition, FAT partition complete, and then returns to the same T-Mobile splash screen and hangs there.
So then I tried putting it into Boot Loader manually (Power On + Camera). No problem, shows IPL 2.26 and SPL 2.26. Plug it into the computer USB port (running XP Pro), and then the USB connection shows on the phone. Attempted to flash the Wizard Love ROM to get this thing back to square-one. Error 260. Attempted to flash the T-Mobile stock ROM. Error 260.
Between each flash attempt, I'm pulling the battery out and starting fresh. I think I've followed all the steps I'm finding in multiple threads. But for some reason I'm not able to get this thing to communicate via USB. All RUU's give an Error 260. Am I missing something?
Forgot to mention I'm following the steps outlined in this thread from Dr P. To the letter!
Also did a little reading up on using the MTTY method in this thread by Drug_Store. Thought maybe the existing ROM might be intact, and I might be able get it to a 256MB MiniSD, then write the backup ROM from SD in boot loader. Well, for some reason I don't even see the USB connection option when I use the MTTY - can't ever get to a point where I can issue commands. Again, I think I'm following the instruction. But still no juice.
Nudge, nudge. I'd donate for a solution that works... otherwise I have to keep letting my 10 year old play The Quest on my phone.