Database Develop

Phone will not turn on.

I've done a fairly comprehensive search here to try to solve this problem but not one post I've found expresses the exact characteristics of my problem AND contains a solution that has worked. I.E. please don't flame me as if a were some lazy idiot. Thank you.
I have a G4 8125 and was able to flash the stock 2.24.001 IPL/SPL to 2.25.001 before I knew that was bad. Applying flawed logic like "I stuck my head in the lion's mouth once and didn't die, lemme try that again!" I thought that the procedure I went through before would work as well. I thought wrong.
I flashed with a ROM that had the 2.26.001 IPL/SPL (I think) and only one of them appeared to "take" upon the first reboot after an apparently successful flash. That is, the boot screen showed only IPL and not SPL. I though, OK, I sometimes see that my GSM version is missing too. No big deal.
Upon the next reboot, the device is bricked. I mean it won't even turn on. I had well over half battery when I did this and now I don't even get a amber charging LED to light up when I plug it in to charge it. I've tried the hardware cold boot (hold comm and voice buttons then soft reset). No dice. I'm afraid that one of the posts I read might explain it -- if the bootloader is updated somehow it "loses" the power button.
My question is this -- is there anyway I can jump start this thing? I've seen some posts about using a 9v battery and others about using an image of a good ROM on an SD card, etc. Can anyone give any feedback here, all in the same place, about whether any of these have worked for you if the phone would not turn on.
Thanks!

same problem here plz help !

I had kind of a similar problem where the phone would not turn on. The only thing I could think of was the phone somehow self discharged the battery to such a low state that the USB charger would/could not charge it. Last ditch effort and not knowing what was going on I pluged it in using the wall charger and after a day it did turn on. You just cant assume the battery is good just because it was.

Thanks for the help. I'll try the wall charger thing out of pure desperation. BTW if any of you guru's out there want to chime in I promise to post a "bricked" FAQ. I think it's sorely needed. Like I said, I did a thorough search of this forum and there are far more questions than answers.
My first question -- how the hell does the ROM get loaded in the first place? That is, obviously the Wizard contains EPROM or flash or whatever -- something non-volatile -- does anyone know how it gets on the device at the factory? Is it burned into the chip before it gets installed on the device or is it somehow flashed later? My guess it that it gets burned by the carrier and if so I'll bet it's not a bunch of lab monkeys with USB cables. Is there a way to completely reload the Wizard from, say, a SIM card? I mean the bootloader too...

Well I gave up and ordered a replacement from Cingular. They were pretty nice about it. Should be here Friday. Next step: in depth research into bootloaders and ROM backups before the next try at flashing my new 8125. By the time I get this figured out the 8525 will be out and I'll have to switch to that

Phone is here. Swapped out the SIM battery and cover. Still won't turn on. Maybe it's the battery?

Most probably it is the battery. Have you tried direct-charging? Here's a procedure I sent to someone else a while ago:
Here's one trick I've used with my boss PDA which did the same thing, the battery drained and it would not recharge with the stock charger.
You'll need to take out the Wizard's battery.
1. Take a DC adapter that puts out 5-6 VDC.
2. Make a note where the positive and negative terminals are. Usually the center/tip is positive and the barrel/ring is negative but this is not a defacto standard. Check the adapter casing to be sure. DO NOT USE AC OR MORE THAN 6 VOLTS! THE BATTERY PACK COULD BE DAMAGED!
3. Attach a wire to the adapter's positive and another wire to the negative. How you hook it up is left to your imagination
4. Now, with the negative wire coming from the adapter touch the negative terminal on the battery. Touch the positive battery terminal with the positive wire. The battery polarity is printed on the label.
5. Charge the battery like this for 15-30 seconds.
6. Now plug the battery back into the phone and attach the charger.
The battery should start charging now. If it doesn't, it means it is deeply discharged and you'll have to repeat the procedure, this time for 30 seconds tops. Again, remember by doing this procedure you're bypassing the charging/conditioning circuits and the battery could be damaged!
Good luck!

I'll be damned...
I used a 9v battery and a twist tie from a bread bag. Three 15 sec charges later, Windows Vista RC1 recognizes the device on USB, loads the driver and starts charging it. I can't resist booting it up -- bonus 2.25.11.1 OS, 2.25.11 GSM and 2.25 IPL/SPL. It's not a G4!

hi to all!
I am suffering the same trouble described few post below...
After an upgrading rom My Qteck 9100 don´t turn on.
I´ve tried charging battery in a cradle during all night, change for another charged battery (from another pda) and it's impossible to turn on.
Anybody have a suggestion or trip?
Many thanks

Re: I'll be damned...
Didn't thought of the 9v and the twist tie... Glad to know your phone is on its way to recovery!
baarod said:
I used a 9v battery and a twist tie from a bread bag. Three 15 sec charges later, Windows Vista RC1 recognizes the device on USB, loads the driver and starts charging it. I can't resist booting it up -- bonus 2.25.11.1 OS, 2.25.11 GSM and 2.25 IPL/SPL. It's not a G4!
Click to expand...
Click to collapse

Does anybody can explain the "how to" using 9v battery?
Thanks

Guess what baarod did was touching his phone battery with the 9v battery negative contact (the one that looks like a little crown) and used a bare twist tie from the 9v positive to the battery positive. He repeated this 3 times for 15 seconds each time.
I have an HT that suffers from the same problem, if I let its battery discharge completely the desktop charger will not activate unless I take the battery off the radio and charge it alone for a few seconds.
LiIon batteries do not like to be discharged completely.
Good luck!
cortezrob said:
Does anybody can explain the "how to" using 9v battery?
Thanks
Click to expand...
Click to collapse

Thank God there's others... not I don't feel so dumb
8125 from Cingular with a G4 chipset. I'm going to go get a 9 volt right now and I'll post again if that little battery blurb works...if not I'll post it while crying and potentialy electrocute myself... (yeah right... more like just short it out forcing me to buy another...but hell I just bricked a $700 phone, what another $60 at cosco huh? :shock: :shock: :twisted: :twisted: :mrgreen: )

One little thing, for a G4 chipset the flashing procedure is different!
You need a firmware without IPL/SPL. Check the forums for the correct firmware to use!
If in doubt, flash the official firmware from Cingular and take notes...
Good luck!

I'm laughing because if I don't, I'm gonna scream
Okay, good advice yellowdragon, except that it's Cingular we're talking about here. Not only did they have absolutely no clue what I was referring to when I referenced the G3 vs G4 chipsets, but the only rom they have posted for firmware upgrades, is the G3 chipset, which of course kills a G4 phone, even though they're sending out G4 phones to the general public to begin with. At work now trying to find the DC adapter with the right specs to try the 9v bypass thing.
Wish me luck people... and if anyone can find Risidoro... I'd love to chat with him... or to see if he has any handy advise on how to fix all this...
peace
... okay it's not working. Tried the 9v battery idea, and nothing. tried with the 9v like 4 times.... each 15 seconds... i get the feeling that the answer is more obvious than it may appear... like it's DEAD! Unless perhaps I read the above wrong and should have done 2 15second charge sessions for the 2nd time of zappint it, each time accumulating more charge time each time I 'jump it". I'm gonna try that...
the battery won't explode... will it?
hope not

I also upgraded a G4 with a G3 IPL ;/ I know it's a stupid mistake, but I was sure that I'm upgrading with G4. I should have used a rom without IPL/SPL ;(
Wizard worked first time after rom upgrading... everything is because power button doesn't work I think. So is there a way to turn a Wizard on without pressing power button?
I don't believe in 9V battery trick... why should it work? My battery was fully charged before upgrading. I'm afraid that I'll destroy my Wizard's battery too :/
If anybody can help, plz help!

install GSM 112 Radio only from ftp

Folks,
Please note that I got a replacement 8125 from Cingular since I could not get my device to power on either. Upon receipt of said device I installed my SIM card, battery and battery cover only to find that the NEW device would STILL not power on. Now THATS a BRICK! ;-)
What I noticed is that when I connected the device to the USB cable, the charging light (right-handside of the earpiece, normally amber when charging) did not come on. I then tried the AC adapter to no avail. I then scoured the forum here and found the 9v trick.
Don't feel bad people -- I got all that working again and tried to flash the new AKU 3.2 ROM from ells. Now I'm stuck at the ROM 2.26 bootloader again :-( I'm just a ROM junkie, no matter how much trouble I get into I gotta go back to the juice!
I'll post how this recovery turns out. If we can keep this thread alive and I keep getting Cingular to send new phones then we might be able to cover every conceivable brick scenario... LOL

Risidoro's 2.26 seems to be flashing my Wizard right now. It's sitting at that pivotal ~96-98% point. Fingernails: chew, chew.
I hope this is not like last time where the updater finished but the Wizard was still at 99%!
Yay! It worked!!!

baarod said:
Folks,
I'll post how this recovery turns out. If we can keep this thread alive and I keep getting Cingular to send new phones then we might be able to cover every conceivable brick scenario... LOL[/QU
Hi Baarod, can you post wich is the method of the 9v battery trick?
Click to expand...
Click to collapse

8125 Bricked HELP !!!

I was trying to update my WM5 to WM6 I have the G4 8125 , now it wont turn on I plugged it in to the charger port and the light that shows it's charging doesn’t even come on. Last night after I was trying to update it went completely blank, I tried to run the Official AT&T RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1 and it wont even connect to my phone it gives me the connect error, every now and then last night it would show the boot loader screen but now its doing nothing someone HELP ME!!!!!!!!!!!! PLZZZ Does this mean my phone is bricked ???

Sounds like the battery is dead at a guess. As you have already seen the bootloader screen that is a good sign. You need to charge the battery away from the phone either in a cradle battery charger or another persons phone. If after charging the battery the phone is still dead I am afraid it maybe RIP.
I am sure others may help you far better than me though

Shew , i hope it is just the battery if its not the battery is thier anything else i can do for the phone ?

I am now in the same boat with my K JAM

What was you trying to do to your phone ? the same thing i was ?

emmanuel_harris32 said:
What was you trying to do to your phone ? the same thing i was ?
Click to expand...
Click to collapse
Basically but I have left the battery out for 30 mins and it has restarted
You can buy A charger which will charge the battery out of the phone on E bay

emmanuel_harris32 said:
I was trying to update my WM5 to WM6 I have the G4 8125 , now it wont turn on I plugged it in to the charger port and the light that shows it's charging doesn’t even come on. Last night after I was trying to update it went completely blank, I tried to run the Official AT&T RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1 and it wont even connect to my phone it gives me the connect error, every now and then last night it would show the boot loader screen but now its doing nothing someone HELP ME!!!!!!!!!!!! PLZZZ Does this mean my phone is bricked ???
Click to expand...
Click to collapse
Most important is to get your battery fully charged atleast, I think it has gone flat,how are you trying to charge the battery ?,it won't get charged through usb cable, cuz usb cable will not charge in bootloaders,it got have a working OS on the phone and only provides 0.5 amp(500 amp power),where as now it'll only start charging if you connect it to a 'Wall Charger' which provides 1 Amp (1000 Amp power), or get a charged battery from a friend and check if your phone gets into bootloaders,if it gets than my friend your saved.WELL,IF NOT,.....I'm afraid you gotta shinny expensive paper weight on ya desk.
which Upgrade Rom were you trying to flash and as you have a G4 device,what method did you adopt to flash the Rom ? a G4 device can only be upgraded through SoftSPL or HardSPL method in case upgrading to a custom build wm6 Rom and or can only be flashed with an official Rom.
Secondly ,if you flashed a G3 specific Rom which includes IPL/SPL in it,will definitely "BRICK" the phone

I just wanted to thank everyone for your help , i got my new battery in yesterday and my phone booted up flashed back to at&t orginal rom. Thank So Much.....

Same battery problem not 50% for upgrade

Hi,
I see loads of people with this problem, did ROM upgrade with no luck. Have a USB / Charger cable.
Now phone wont charge.
Comes on when connected to mains charger.
Will boot in Bootloader mode (no usb) when on charger.
Will talk in USB (Activesync) mode when on charger.
Wont do USB in Bootloader mode (turns off even when on charger)
Carnt do ROM load in Boot loader mode cos turns off
Carnt do ROM through Active Sync cos less than 50% battery.
Is there a ROM that will run through ActiveSync without the battery check ?
I am yet another person asking for a copy of a SD image for download (or even where one can be purchased)
Any other ideas ?
Thanks
TBW

Or is it possible to create a SD card ROM from the ones that can be downloaded from the site ?
Thanks
TBW

Anybody got ideas on this ? It looks like its a common problem, have looked through alot of the posts about this and there's been no fixes.
Cheers
TBW

Any links to a SD Card ROM ?
Hi,
Is there any links to a SD card ROM anywhere ? Its the only method I can think of to get this phone working again, There's still solution posted anywhere !!
Cheers
TBW

Any ideas anyone ?
Any ideas anyone ?

My Charmer, is defintely a paperweight now. It doesn't even turn on, or do a hard reboot. The battery only measures 0.22V with a multimeter.

Use an universal Charger with 5 Volt to charge the battery out of the Charmer.
This may work. Or it will damage the battery, but I think it will work.

Hi, i have read about a BATFIX.cab. Try this one.................

The batteryfix.cab, does not work for me. All of the universal chargers I'm seeing here, are limited at 3.7V. This isn't even enough to turn on the phone.

No Battery, stuck at tri-color screen

I was flashing my phone repeatedly last night. I've read the forums and have done about 4 successful flashes already. The problem is, I've found a WM6 rom for the Wizard that I wanted better than the ROM already inside my phone, and I proceeded to flash it. But I left the computer and phone by itself so that I could rest a bit (I've spent hours in front of the computer flashing my phone), and fell asleep. When I woke up, I noticed that the flashing failed, and it was at the tri-color screen. Then, it died on me. No battery, obviously, being stuck at the tri-color screen the whole night. Now, it doesn't charge or turn on. I know I just need a battery to run the phone. But where I'm from, batteries for the Cingular 8125 are rare, and I'm one of the few that has an 8125.
I don't know anyone who has a battery for the 8125, and there's nowhere to buy from here. Any recommendations?

First of all be sure that you haven't flashed a G4 ROM in a G3 device (or vice-versa) which would have made it a brick.
In case you haven't screwed up the bootloaders then look for the battery jump start thread that teaches how to revive a dead battery
good luck

ianestradalives said:
I was flashing my phone repeatedly last night. I've read the forums and have done about 4 successful flashes already. The problem is, I've found a WM6 rom for the Wizard that I wanted better than the ROM already inside my phone, and I proceeded to flash it. But I left the computer and phone by itself so that I could rest a bit (I've spent hours in front of the computer flashing my phone), and fell asleep. When I woke up, I noticed that the flashing failed, and it was at the tri-color screen. Then, it died on me. No battery, obviously, being stuck at the tri-color screen the whole night. Now, it doesn't charge or turn on. I know I just need a battery to run the phone. But where I'm from, batteries for the Cingular 8125 are rare, and I'm one of the few that has an 8125.
I don't know anyone who has a battery for the 8125, and there's nowhere to buy from here. Any recommendations?
Click to expand...
Click to collapse
First os all your Wizard is not a brick. To revive your battery try using a wall charger to charge you battery, or you can leave it attahed to a wall charger for some time and it should start charging after 10-15 mins (becoz one i got a dead battery and did the same) Once the battery is revived then flash it to a Official ROM, afterwards any custom ROMs or what so ever. I hope i helped. TC

i've the same problem!!! i leave the phone attached the whole night to the charger...but it was in bootmode, so it doesn't charge!!! it hasn't the power to flash my phone...when it arrives to the 85% (when the phone write into the flash memory) it reboots.....what must i do? i tried to jump start...with a 12v adapter...but nothing....

It won't charge in Bootloaders,as it doesn't provide any charging circuit .The phone must have and boot up to a working OS (Windows) to start charging,only then it has a charging circuit.
Try to get a fully charged batter ,may be borrow it from a friend or try to charge your battery with friends phone,flash a rom and only it'll start to charge.

i know....but...i have not a friend with a ppc like mine!!!! and even if i'll buy a new battery....how can i charge it????? a friend of mine has a qtek 9000....but the battery is different from mine.......

F0ll3 said:
i know....but...i have not a friend with a ppc like mine!!!! and even if i'll buy a new battery....how can i charge it????? a friend of mine has a qtek 9000....but the battery is different from mine.......
Click to expand...
Click to collapse
No need to buy a battery i say you use a External Battery Charger. Because even buying it would be cheaper then the battery itself and would help you in future too. I hope i helped. TC

Thanks
xda2_haseeb said:
First os all your Wizard is not a brick. To revive your battery try using a wall charger to charge you battery, or you can leave it attahed to a wall charger for some time and it should start charging after 10-15 mins (becoz one i got a dead battery and did the same) Once the battery is revived then flash it to a Official ROM, afterwards any custom ROMs or what so ever. I hope i helped. TC
Click to expand...
Click to collapse
Thanks, dude. I never even tried charging it with the wall charger. There seems to be other people that have the same problem as I do. Now my phone is up at the tri-color screen, and I'm charging it, then Ill start flashing again. Thanks again!

No Problem but now remember if you find ppl with same problem (on the forum) dont forget to guide them to this Thread. And no need for the thanks. TC

zabardast_1 said:
It won't charge in Bootloaders,as it doesn't provide any charging circuit .The phone must have and boot up to a working OS (Windows) to start charging,only then it has a charging circuit.
Try to get a fully charged batter ,may be borrow it from a friend or try to charge your battery with friends phone,flash a rom and only it'll start to charge.
Click to expand...
Click to collapse
Thanks, dude. I never even tried charging it with the wall charger. There seems to be other people that have the same problem as I do. Now my phone is up at the tri-color screen, and I'm charging it, then Ill start flashing again. Thanks again!
Click to expand...
Click to collapse
@ianestradalives's as zabardast_1's has said, your phone WILL NOT CHARGE unless windows Boots. Either buy a new battery or find someone with the same phone or an Orbit(as they use the same battery) also if you buy a new battery it generally arrives with enough charge to use for flashing(It did for me anyway). The only other way to do it would be to buy a dock with a second battery charging slot. Using the wall charger wont do anything except stop it from restarting ,while its plugged in.
@XDA2_haseeb why point people who have the same problem to this thread, if the answer you have given is incorrect?

scousemartin said:
@ianestradalives's as zabardast_1's has said, your phone WILL NOT CHARGE unless windows Boots. Either buy a new battery or find someone with the same phone or an Orbit(as they use the same battery) also if you buy a new battery it generally arrives with enough charge to use for flashing(It did for me anyway). The only other way to do it would be to buy a dock with a second battery charging slot. Using the wall charger wont do anything except stop it from restarting ,while its plugged in.
@XDA2_haseeb why point people who have the same problem to this thread, if the answer you have given is incorrect?
Click to expand...
Click to collapse
Dude, sorry to disappoint you, but his advice was correct. My phone is now up and running, and it has NBD 9.2. The advice he has given is correct. It works.

Ok,was your phone in Bootloaders (muliticolor screen) or with a working OS installed on it when you charged with a wall charger ?

That's exactly what was i was about to ask Zabardast_1
As there is no way he could charge his phone while it is in bootloader mode. He either had battery power already in it and messed up the flash or you have just been lucky when you took the battery out of the unit and reinserted it and there was enough power left to flash

zabardast_1 said:
Ok,was your phone in Bootloaders (muliticolor screen) or with a working OS installed on it when you charged with a wall charger ?
Click to expand...
Click to collapse
In bootloader screen. If you were flashing a rom and it failed, you usually end up in the tri-color (aka "Bootloader") screen. Do what haseeb said (like I did) and plug your wizard to a wall charger and wait for a few minutes. When I plugged mine, it immediately lit up. Good hunting!

scousemartin said:
That's exactly what was i was about to ask Zabardast_1
As there is no way he could charge his phone while it is in bootloader mode. He either had battery power already in it and messed up the flash or you have just been lucky when you took the battery out of the unit and reinserted it and there was enough power left to flash
Click to expand...
Click to collapse
Nope. I'm sure the battery was drained. The other night, my phone was in the bootloader screen THE WHOLE NIGHT. And yesterday, I tried reflashing, but it won't start anymore because of - obviously - no battery power.
IF you don't believe me, fail a flash and drain the battery. Then plug it into the wall. It really works.

scousemartin
YUP! thats very true.
The question here is 'How did he charge in Bootloaders with a wall charger',it has to have a working OS on it to start the charging circuit,which isn't present while in Bootloaders.
Flashing is a separate issue.

it will light up as it has power but it WONT CHARGE IT. You were LUCKY that's all and you had power in your battery. You just never realised it. If you want to prove us wrong let the battery go low and then try your revival attempt again. I guarantee you will be buying another battery or charging it somewhere else

also i have been through this personally with my xda mini-s and the only remedy was to buy another battery (or recharge it). You could leave your phone connected to the wall charger for a week and it wont make a blind bit of difference to the battery level. I know because i tried.
Anyway glad you got it sorted ,but the solution to your problem was not charging the phone. Thats all i have to say on this matter now

scousemartin said:
also i have been through this personally with my xda mini-s and the only remedy was to buy another battery (or recharge it). You could leave your phone connected to the wall charger for a week and it wont make a blind bit of difference to the battery level. I know because i tried.
Anyway glad you got it sorted ,but the solution to your problem was not charging the phone. Thats all i have to say on this matter now
Click to expand...
Click to collapse
It did get sorted. But I am really sure about the battery thing. I guess this is an anomaly. Besides, the XDA is different from a Wizard.

lol the xda mini-s is exactly the same device a 8125 is, they re both wizards

[Q] G1 unbale to charge battery

my G1 can't charge ,when i pluged it , it get warm at the bottom. And it also can't be charged when i use usb cable to connect to my PC.if i charged with the desktop standing charger,and put the battery into G1,itcan work well,but after one hour or more,it get warm at the bottom either,even sometime it close by itself,Anybody know what's wrong with my G1?
who can help me!!!!!!!!!

if its getting warm it seems as if it is getting something but not charging. Try plugging in headset. This will eliminate the dodgy connector theory if it works

Hello
I have the same problem, no charging status when os running, no charging light and no connection with pc. G1 is charging only when off. Anybody have idea ?

do this belongs ins the devs threads?
uh, for the one with no led while charging - are you using JACHero ROM by any chance? That may be why.
...its normal for that one

Call tmobile... get new one.. tell em u tied different outlets andwhen u tried diferent batery it works

Hettfield said:
Hello
I have the same problem, no charging status when os running, no charging light and no connection with pc. G1 is charging only when off. Anybody have idea ?
Click to expand...
Click to collapse
Can we say, Warranty exchange?
or buy a new battery

I have new battery, 2 chargers, and jf 1.5 rc 33.
I'm from poland and I have problem with downgrade to basic "era" software, Idont know why. Now I install rc 29 and have default spl.

i believe your battery charger port aka usb port is damaged so you must need a replacement.

maybe its damaged but, headset work perfect. I cant get warranty exchange because I dont know how to install oryginal era software.
here is the link with era software http://megafileupload.com/en/file/104629/signed-TMPL-RC9-from-TMPL-RC6-f5759790-zip.html

Hettfield said:
maybe its damaged but, headset work perfect. I cant get warranty exchange because I dont know how to install oryginal era software.
here is the link with era software http://megafileupload.com/en/file/104629/signed-TMPL-RC9-from-TMPL-RC6-f5759790-zip.html
Click to expand...
Click to collapse
All you have to do is rename the file you linked to "update.zip" put it on the root of your sdcard, restart, wipe and flash it as an update.

bqwd36 said:
my G1 can't charge ,when i pluged it , it get warm at the bottom. And it also can't be charged when i use usb cable to connect to my PC.if i charged with the desktop standing charger,and put the battery into G1,itcan work well,but after one hour or more,it get warm at the bottom either,even sometime it close by itself,Anybody know what's wrong with my G1?
who can help me!!!!!!!!!
Click to expand...
Click to collapse
I had the exact same thing happen to me it is apparently a device problem that seems to be spreading. You can't charge the battery but if you put another battery in it you'll be alright. They let me take the one in the display at T-Mobile in excahnge because the battery is in fact completely fine its the main board itself. You're gonna have to unroot the system and get it back to at least stock and mail it in to HTC (they charge you a $29 triage fee if they determine it was due to something you did ie water damage or software modification). Anyway get your hands on a charged batery unroot send it in and they'll replace the board and send it back.

Diceman4 said:
All you have to do is rename the file you linked to "update.zip" put it on the root of your sdcard, restart, wipe and flash it as an update.
Click to expand...
Click to collapse
I have E:Failure at line 1
i have radio 1.22.12.29
cpld 4 and hboot 0.95.0000

Hettfield said:
I have E:Failure at line 1
i have radio 1.22.12.29
cpld 4 and hboot 0.95.0000
Click to expand...
Click to collapse
Try this one
www.4shared.com/file/118807172/edd2dda2/ERAFirmware.html
If this doesn't work I can change something else that should work.

now i have E:wrong digest android info.txt
E:Veryfication failed
Maybe i need Android RC6 ?
Diceman4 look at the size of zip file its only 15MB (?!)

Hettfield said:
now i have E:wrong digest android info.txt
E:Veryfication failed
Maybe i need Android RC6 ?
Diceman4 look at the size of zip file its only 15MB (?!)
Click to expand...
Click to collapse
I agree it is weird. That is the size of the file that you linked to...

because this file is to manual update firmware (sorry I dont read carefully).
it is possible to get orygilnal era firmware ?

Hettfield said:
because this file is to manual update firmware (sorry I dont read carefully).
it is possible to get orygilnal era firmware ?
Click to expand...
Click to collapse
I have no idea, I've never seen it. Try seeing if there is an android board geared told poland. That would be your best bet.

in my opinion i need only rc6 firmware, but i try to find it with no results.
signed-TMPL-RC9-from-TMPL-RC6.f5759790.zip

more charging problems
hey guys, im having a similar problem, but slightly different. my device will boot up if i have it plugged in and hold the power button a coupld of secons after the initial single red blink of the led, but when it boots up it says there is 0% charge in the battery and even though it says that it is charging, the battery never appears to gain any charge. i've had the phone for over a year. how long does htc's warranty last?