Related
Hi,
I have a used qtek 9090 With the Italian version.
When i try to upgrade the rom to a english one, ou upgrade with a original italian version it always get stuck on the bootloader screen.
On the PDA i get a screen only saying usb 2.07.
On the PC it get's trying to retriev information.
If I cancel the operatio after a while I have to run a litle program to get out from bootloader.
So I need your help with this.
My guess is the pda it's locked or something is wrong with the bootloader.
Regards
kruzpt said:
Hi,
I have a used qtek 9090 With the Italian version.
When i try to upgrade the rom to a english one, ou upgrade with a original italian version it always get stuck on the bootloader screen.
On the PDA i get a screen only saying usb 2.07.
On the PC it get's trying to retriev information.
If I cancel the operatio after a while I have to run a litle program to get out from bootloader.
So I need your help with this.
My guess is the pda it's locked or something is wrong with the bootloader.
Regards
Click to expand...
Click to collapse
use Mitty, when stuck on bootscreen
which instruction pass to multi-port tty with device stuck on bl?
I've tried your solution but it doesen't work on my device.
I See again:
- Serial v2. 08 (outside of cradle)
- USB v2. 08 (inside cradle)
My device:
Vodafone VPX 1620
Model PH2OB2
Thanks to all
I also have a Qtek 9090 and am stuck on the "serial v2.08" screen. I've searched all over the internet for the last hour and while this site is (by FAR) the best resource I still haven't been able to get past that screen. I've tried hard and soft resets by holding down the power key, voice record key, and pushing the stylus in the reset button on the bottom with no luck. I've tried just the power and reset buttons and even all four buttons (reset, power, record, camera) - which was a little hard to manage But now I can't figure anything out and could REALLY use some help as I'd hate to have an expensive paperweight after only owning this unit for four days.
Btw, I've gotten to this point while (rather stupidly, in hindsight) clicking on EnterBL.exe during an attempt to upgrade to WM6
Success! I got it after all!
Was updating my dads SPV M700 to WM6 and have hit a problem ....
The rom image updated ok, and I used AX3L's 2.0.8.
Unfortunately during the GSM update the software crashed, and froze at 51%. I had to re-boot and now I can't use the phone.
When I re-set the phone it says No GSM at the HTC screen and then stops loading at the WM6 front page.
I can get into the Bootloader by pressing the Power/Camera/Reset buttons, but when I try to re-flash GSM is says error 270, corrupt image. I have tried several files with no luck.
I would appreciate a hand ..... My dad is going to kill me
Thanks
gaz_az
try press
power button + camera + reset
to enter usb mode
then reflash the radio again.
hope this works
You can try 2 other things!
Download the Radio ROM again- you may have had a downlaod glitch in the 1st one. V1.38 is the best one to try.
Download and install the offical HTC WM5 ROM- this should be a full ROM including Radio, so sometimes completes more effectively. If you are brave, you can them retry the WM6 flash!
since bricking a hermes i stopped taking chances doing rom upgrades via usb..
the method that is most reliable ad safe is... via SD card
extract RUU_signed file from the upgrade pack (use winrar) and then copy it to the root of a blank sd (mini or micro etc) and rename to TRINIMG.nbh ..enter bootloader and follow the steps.. its fast and most reliable
Ok - Thanks for the help, but no luck so far. I have tried the suggestions above !
Heres what I have done ...
Hard reset - no change
Tried to re-flash with WM6 and WM5 cooked roms, but an error comes up saying the images are corrupt. This happens with any image I try.
I have also tried a legit HTC WM5 rom upgrade image, but it doesn't work either. It gives an error at 1% saying invalid device ID.
What I can do it get into the standard bootloader screen, which shows I have a USB connection when plugged in. If I allow the phone to boot up it stops at the WM6.0 picture. It won't go far enough to allow me to get an activesync connection.
ANy more adivice would be greatly appreciated !
gaz_az
Next thing then, is to try and obtain a downloaded Orange M700 ROM- there are a few links hereabouts.
For some reason, your device seems to want only its home ROM. If that fails there are other methods before sending back to Orange!
I downloaded an Orange rom, but still no luck. It gets to 1% again, then says there is a error/corrupt image file. Same as any of other cooked images !
What next ??
well if you were my son, i would advice you,to buy a plane ticket for somewhere very far,leave the house while i sleep,and pray every day you have left in your life,for not find you on my way
uhm, question about boot loader and flash on boot loader mode.
I copy file TRINIMG.nbh to root card mini SD, and i can't go as you say...
always Tri colors screen....
gaz_az said:
I downloaded an Orange rom, but still no luck. It gets to 1% again, then says there is a error/corrupt image file. Same as any of other cooked images !
What next ??
Click to expand...
Click to collapse
You are running out of options
Your choices now are to go further down the 'fiddling' route, or give up and return the phone to Orange for repair. At least if its is stuck in bootloader, they may not spot that you have been meddling
If you want to play more, there are very few Trinity specific fixes, but possibly some of the questions/answers in the Hermes WiKi may help, though the Bootloader versions etc won't be relevant.
[Edit: When you are in Bootloader mode, what version numbers are showing on the screen?]
is it so wrong i was smiling when i read this.
does make me wonder if u told ur dad what u were going to do or whether u were trying to be cocky by giving him a better phone without him knowing.
all i can say is, UNLUCKY !
I must say things are looking bad - I think it would take an original orange SPV rom if I could get one. Been to the orange website, but no luck !! Anyone know if orange released one ??
Been looking at the Hermes unbrick thread. Is there a way to enter KITL debug mode in the trinity ??
G
P.S. Dad knew I was upgrading the phone, already did it once for him and it went ok. No sure he knew I could acutually kill it
No Orange haven't released an official rom.
Well Orange UK haven't Orange FR have, so unless he speaks and reads french that's not an option.
Well, French or not, you've probably got nothing to lose by trying to load the official French ROM
Go Here and click the Mise-a-jour link (which is French for ROM) and it will open a zip file download without the need to verify the IMEI number.
If that doesn't work, nothing will! If it does load, you will at least have a working phone, even if it is in French, and you can go back over the ROM update again, remembering to apply the SPL Bootloader first!
Still "not allow", i don't know what the hell Orange was doing with P3600?
Lock everything?........it's suck !!!
No luck with the French ROM. Same thing gives an error message about wrong device ID.
I am one step from chucking it in the bin. Any more last minute ideas ??
erh, bizzard,i can't use "wtty.exe" to view my CID ...
i tape "info 2"and it always appear
Cmd>info 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
Cmd>
...............................
Someone have issue for that?
If i can view CID code,i think i can find the right ROM to re-vivre...all suck !!!
erh, hey guy, your boot loader is english or french? sorry if it's the most stupid question of the day......i think french device use french boot loader,right?
i mean, when screen tri-color appear, use mini SD card to flash ROM, the language it apprear itself is english or french.
p/s : i was telephone to the HTC center, and they say as usual, send it to the center repair.
For french user address is : be sure u have enough garanty which required.
send them and make them crazy.....
CIRMA ELECTRONIQUE
9A14 CHEMIN DE BARATEAU
ZONE INDUSTRIEL DE LA LANDE
33451 SAINT Loubès
If you can figure out how to compile splxploit, you can fix this, see
http://forum.xda-developers.com/showthread.php?t=308691
thank anyway,i will try it before tomorrow,cause i will send them my device for repair.
I have a stuck image on my 8125. The phone "boots" but only shows a white screen, and is unusable.
The "a2sd all" restore option mentioned in the forums doesnt work for me. I have read on several forums that I should be able to reflash the OS from the bootloader, though I cant find any instructions on how to do this
Could someone point me in the right direction for how to flash an OS VIA bootloader?
Thx
1. Get the phone to bootloader (tree color mode) - I think by soft resetting and pressing the camera button at the same time
2. Connect it to the computer (Windows XP) with a USB cable
3. You will notice "USB" written in a lower corner of the phone (this means it is connected)
4. Now you can flash your provider's ROM without any problems
I am not sure whether the bootloader flashing is possible from Windows Vista.
You must flash normally (in bootloader you cannot use either shelltools or SoftSPL - so use your provider's ROM).
Mirek
Mirek - not to be totally ignorant, but the step 4 is what I'm having problems with .... where can I find either a providers ROM, or something that I can actually use while in bootloader mode?
Thanks!
NM ... Found it!
For anyone reading this .... You can get the provider ROM for the 8125 from HTCAmerica here: http://www.htcamerica.net/support/8125/software-downloads.html
Thanks for your help!
mirekluza said:
1. Get the phone to bootloader (tree color mode) - I think by soft resetting and pressing the camera button at the same time
2. Connect it to the computer (Windows XP) with a USB cable
3. You will notice "USB" written in a lower corner of the phone (this means it is connected)
4. Now you can flash your provider's ROM without any problems
I am not sure whether the bootloader flashing is possible from Windows Vista.
You must flash normally (in bootloader you cannot use either shelltools or SoftSPL - so use your provider's ROM).
Mirek
Click to expand...
Click to collapse
Dear Readers,
I'm having problem with my Dopod 900(,Qtek 9000,HTC Universal,O2 Xda Exec,Jasjar ). Can somebody please tell me what to do?
Before this, every time somebody called, the PDA lost the network bar and start to search or network and reject the calls automatically and also i wasn't able to send SMS. Now, i tried to install WM6 crossbow, the phone even cannot be on !!! even when i connect it to the charger, even the light will not be on. the only page that i can see is a white page asks Press 0 to Restore factory default or press X to exit. either perss 0 or X, the phone will be off and i cant turn it on with power key....
Please tell me what can i do ?? I really need your help.
PLEASE REPLY, PLEASE.
[email protected]
Warm Regards to All
G-Jorji
brick?
hey guys, i need a little help. i downgraded my phone to buttons rom and then i was gonna attempt to upgrade the ipl/slp to 2.xx. so i downloaded the wizard ipl/spl 208 from the ftp site. i had a successful flash but when it went to reboot, my wizard never turn on again. ive searched the forums but it seems to me i have a brick found nothing. has anyone had the same situation happen to them? and find a solution?
it wont turn on at all anymore
acuraholic said:
hey guys, i need a little help. i downgraded my phone to buttons rom and then i was gonna attempt to upgrade the ipl/slp to 2.xx. so i downloaded the wizard ipl/spl 208 from the ftp site. i had a successful flash but when it went to reboot, my wizard never turn on again. ive searched the forums but it seems to me i have a brick found nothing. has anyone had the same situation happen to them? and find a solution?
it wont turn on at all anymore
Click to expand...
Click to collapse
WHAT did you downgrade from?
Did you re-unlock your G3?
How's your battery?
acuraholic said:
hey guys, i need a little help. i downgraded my phone to buttons rom and then i was gonna attempt to upgrade the ipl/slp to 2.xx. so i downloaded the wizard ipl/spl 208 from the ftp site. i had a successful flash but when it went to reboot, my wizard never turn on again. ive searched the forums but it seems to me i have a brick found nothing. has anyone had the same situation happen to them? and find a solution?
it wont turn on at all anymore
Click to expand...
Click to collapse
IPL/SPL 2.08? Does that exist? Do you mean 3.08?
Are you sure your device is a G3? Or you killed it when flashing Button's ROM?
i posted this in another thread but no one replied so thought this one mite be more busy. forgive me if this is the wrong place to have posted this.
i am new to all this and i stupidly went running into things and tryed to ROM upgrade my t-mobile MDA Vario II (HERM300), not knowing i had to CID unlock first, it has broke! when i boot it up i can not get passed the t-mobile splash screen and it also flashes "no-gsm". i have read many suggestions on fixing this but i have had no luck. i can get into the boot screen however and get the red green and blue stripes.
i have IPL 1.01 and SPL 1.04.
it will allow me to connect to my PC with USB but active-sync does not recognize i have connected the phone.
please help someone. i just need a way i can get this thing working again. if i could just get the phone into a state of use again that would be good.
RockGod117 said:
i posted this in another thread but no one replied so thought this one mite be more busy. forgive me if this is the wrong place to have posted this.
i am new to all this and i stupidly went running into things and tryed to ROM upgrade my t-mobile MDA Vario II (HERM300), not knowing i had to CID unlock first, it has broke! when i boot it up i can not get passed the t-mobile splash screen and it also flashes "no-gsm". i have read many suggestions on fixing this but i have had no luck. i can get into the boot screen however and get the red green and blue stripes.
i have IPL 1.01 and SPL 1.04.
it will allow me to connect to my PC with USB but active-sync does not recognize i have connected the phone.
please help someone. i just need a way i can get this thing working again. if i could just get the phone into a state of use again that would be good.
Click to expand...
Click to collapse
I don't think you'll get much help here as this is the WIZA100 & WIZA200 forum, not the HERM300...
RockGod117 said:
i posted this in another thread but no one replied so thought this one mite be more busy. forgive me if this is the wrong place to have posted this.
i am new to all this and i stupidly went running into things and tryed to ROM upgrade my t-mobile MDA Vario II (HERM300), not knowing i had to CID unlock first, it has broke! when i boot it up i can not get passed the t-mobile splash screen and it also flashes "no-gsm". i have read many suggestions on fixing this but i have had no luck. i can get into the boot screen however and get the red green and blue stripes.
i have IPL 1.01 and SPL 1.04.
it will allow me to connect to my PC with USB but active-sync does not recognize i have connected the phone.
please help someone. i just need a way i can get this thing working again. if i could just get the phone into a state of use again that would be good.
Click to expand...
Click to collapse
You say that your device is still able to enter bootloader...? If this is correct then you do not have a brick. I understand that you do not have a Wizard, but a Hermes.
This is what you need to do:
Download the Hermes Official WM5 T-Mobile Rom
Put your Hermes in bootloader mode
Connect to your PC via USB
Run the ruu_hermes_tmhu_1.21.116.4_1.05.02.00_wwe_ship.exe that you just downloaded and you should have a working Hermes again.
Next time you want to upgrade your phone, you will want to read into what you are doing VERY extensively. You will find volumes of information under the Hermes sub-forum or in the WIKI under Hermes.
Good luck. Post back here if this was helpful just so I know I didn't waste my time.(thanks)
Non-Free Way to Unbrick
I bought one of these that was bricked one time. (for super cheap). After hours of trying stuff I broke down and paid $30 at imei-check.co.uk They sim unlock and CID unlock all at once. The result was an UNBRICKED phone. I still sold it and made about $100 profit. I think an HTC employee with insider info runs the site. Good luck.
Hey Chaps,
Just thought earlier today i'd have a go at upgrading my phone with the new HTC firmware for my Vodafone Kaiser. First i tried it on it's own only to find the 'vendor' had blocked the upgrade, then i ran the HARDSPL software, when it rebooted my phone to the tri-colour screen i stopped pressing enter on the batch file and ran the HTC upgrade again! ... success - sort of; the upgrade got to 15% and stopped with a connection error (my usb's dodgy i think), then when the phone rebooted to the tri-colour boot loader it'd a) no longer accept the HTC Rom (vendor thing again) and b) become irritatingly broken.
Is it possible to flash an older vodafone rom to the device? if so, where can i find such a beast. Or does anyone know of any devilish ways to put the new rom on using the bog standard bootloader?
Thanks in advance big time to any clever phone experts who can de-brick my... er... brick
Dan.
your supposed to install hardspl before upgrading it if you try it on its own it will brick it at least thats what i heard from the stickies
azazelx, he has hardSPL installed, anyway.
@JimmyJangle: flash via microSD card. [url="http://wiki.xda-developers.com/index.php?pagename=KaiserSDFlash" URL]Read here.[/url]
You need winrar to extract file nbh from the shipped ROM.exe.
Hmm, i don't think i do have HardSPL actually installed,
When i saw the tricolour screen come up with different version information I stopped that batch file that was installing HARDSPL (impatiently) and started the HTC one (which failed at 15%). So now i (think) i have a phone with no firmware and the bootloader says:
KAIS130
SPL-1.56.0000
CPLD=8
I reckon if i can find a vodafone made rom the bootloader'll let me install it.
Any idea where i could find one?
What is ur orginal shipped ROM?
Your solution now is flash back the orginal ROM by using microSD card method I mentioned above, install HardSPL succesfully, then flash whatever ROM you prefer.
Hey Nghiem,
Thanks for the help, that link doesn't go anywhere though.
Also, wouldn't i need the original rom from somewhere in order to do that?
Thanks,
Dan
where did you buy the phone e.g vodafone, orange, etc...so I can tell you the original ROM? Because you phone CID is not unlock, hence you must flash the back the shippied one.
Get the WM 6.1 Vodaphone official here http://forum.xda-developers.com/showthread.php?t=365058
Hi,
I got the phone from Vodafone in the UK.
It had WM5 on it... erm, that's it.
I've just beem trying to load original voda roms back on to it but it's not happy - i don't know if they really are the originals though, one says 'reconstructed'.
Dan
Actually, that was the rom i tried and it came up with the Vendor ID error.
Dan.
Link on post #6 is the official not reconstructed. How about download directly from Vodafone website? It's strange when you have carrier ID block even with its ROM. Also, try reconstructed ROM listed here http://forum.xda-developers.com/showpost.php?p=1586817&postcount=2
Search for mtty, see if it can help you out.
MTTY saved the day!
Only 3 hours of my life lost!
Thanks,
Dan
Cheers. Don't forget to flash HardSPL and read the wiki before doing anything.