Related
Hi all,
Just spent a VERY frustrating day - read all i could find and learned much more than I wanted to know about PCs (I use a MAc).
Upgraded to wm5 using Build 14343. Now I cannot load anything into the phone using Activesync OR Missing Sync. Activesync won't recognise the phone at all, and I tried every suggestion on the boards - firewall ports, tcp/ip, reinstalling 4.5 then back to 4.2.
It's interesting that Missing Sync (Mac) will recognise and sync but won't allow me to install - .cabs just vanish into the ether.
Is WM5 actually worth it all? It seems like I've lost a lot of useful capability (buttons, camera, etc) for no great reason.
Any solves greatly appreciated. Now I'm going to bed.
Paul D
Baniaczek's WM5 ROM is great for me. It has tons of things way better than the original Wm2003. Connects to ActiveSync without a problem. Try to put that one on the device.
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel_WM5_Home
Better File Same problem
I've upgraded the ROM.
Still no activesync. Ran the troubleshooter.
Said there's an issue with RNDIS not giving an IP address.
I've checked the LAN connection in Network settings but it won't repair.
I'm not even sure that Activesync created the link as there doesn't seem to be the "Connect using WM device" that it says should be there.
What now?
*&^%$* WinDoze. Roll on iPhone OSX.
Ahh. This is clearly an issue with the PC. If you were able to upgrade the rom - that prooves that your cable and your BA is okay. There must be some Antivirus, or Firewall problem. If you're using BitDefender Antivirus, for example, this is a known issue. You need to update it. Other antiviruses/firewalls may have similar issues.
Try to move to another PC, or reinstall your Windows PC. This problem is not related to your BA.
Another idea:
Unplug device, then
Start > Settings > Connections > USB to PC:
Disable the Advanced network functionality > ok
Plug it back
This will make your PDA connect to the PC via a Serial link (Like Wm2003 used to), rather than a network link (Like WM5 uses to).
It's still a PC problem though.
reflash again your pda.
today i had the same problem after one clean intall.
upgraded again with the same rom (the one you can see in my signature) and now, i am able to use active synch.
Ok Some Progress
I disabled the "advanced network functionality".
Active Sync no luck - it isn't correctly installing the hardware in Virtual PC on the Mac. I don't know why.
However, Missing Sync now actually begins to load activesync on the PPC, and then gives this message:
"Cannot start communications with the desktop computer. The communications port is not available. Another program may be using the port, or it may not be valid.
Quit any programs that may be using the port and reconnect. If the problem persists, restart your device using hte instructions provided by the manufacturer."
I remember reading somewhere that Baniaczek had assigned certain ports to certain things. How do I find out which it wants and change it?
thanks guys, we may lick this yet.
Paul D
Same message in VPC
Hooray,
I now get the same message in Virtual PC, after disabling "Virtual switch networking" and restarting the PC.
This means that the issue is now the port on the PPC.
PaulD
That's great..
I don't think so...
In baniaczek's rom, COM6 is assigned to shared GPS, but that can be easily changed from the settings, by setting it to none.
Go with your BA to a real PC that has only WinXP and ActiveSync installed, and nothing else (especially no Antiviruses). And no virtual PC's, as they depend on the host os! It's normal, because if your host OS can't connect, the virtual OS inside will have the same door closed.
I had the same problem before, and I definitely state that this is a PC problem, not a device problem. Same hardware connected to a different PC, will work, you'll see...
Reflashing the rom may help, as it will be detected as a new harware, that your system will let in. But you say you already did that...
Won't actually solve the problem
If I had a PC, that would be the easy solve. I don't, and really need the &$# thing to work on the machine I have.
For the moment I went back to the original Mamaich 14343. I can get .cabs into the phone via the card reader (the original problem on the Mac is that Missing Sync 3.0.2 has installing issues).
that doesn't allow me to load .exe, for which I need activesync, on my Mac, which runs VPC 7.0.2.
I really need to find out why VPC isn't working with TCP/IP.
Baniaczek's ROM is the best apparently, but has a com issue. It is also much easier to installl than any others I've found. I tried Xplode's ROM kitchen but the exe file wont run.
Paul D
hey, reinstall again the rom!
OK OK
Ok Sandstorm, I'll try it when I get the chance. At the moment the phone works but this ROMisn't as good as Baniaczek's.
Thankx for the tips
PauL D
Device won't install
Ok Internet works. TCP/IP works.
Issue now is that the device won't install properly - keeps giving a #10 error (device won't start).
So I can't reflash the ROM or anything until I get XP recognising the connection.
Paul D
turn on the upgrade program, "kill" the active synch running processes in your xp taskmanager, set the device in "bootloader" mode, place it in the crade and run the upgrade.
When i do my upgrades, i never do them with active synch enabled.
upgraded ROM again
Upgraded again - still no change
I flashed again to Baniaczek's ROM. Still will not install correctly in VPC. XP says I have a Generic Blue Angel connected via USB, but will NOT install the WM5 device.
Is this a COM port issue? Can I change that (details please)? For some reason, VPC simply won't recognise the WM5.
I have turned off "Advanced network connections" on the XDA. Nothing. Turned it back on.
I have it set to: server-assigned Ip address.
I have tried to change the IP settings manually, but never had a response. I might fiddle with that again.
AAAAAARRRGH!
thanks all,
Paul D
hi guys i have the following problem
i just replaced a new LCD+touchscreen on my 8125 (G3) and i can't connect it on ActiveSync... it simply wont recognize it.. even before i changed it i wasnt able to connect ppc to computer... but when i attach the usb to PC i hear the voice of something connected on USB port, and than the ballon pops out and says me the device was not properly connected...
i've tried changing older and newer ActiveSync's programs, they all function as same... when i press camera+soft reset (bootloader mode) i get the bootload mode and on the bottom i can see when i attach USB... but still it wont update any ROM to PPC... i even tried removing the mark from ActiveSync menu saying ''Allow USB Connection with this desktop computer'' but still it says me device not recognized... wtf?!?! I cant do nothing, upload ROMs neither browse...
please any help appreciated...
and yes, i tried hard reset too and i get the same... tomorrow ill go on 2nd PC to try on it but i have a feeling i'll get the same error there...
HELP!
thx bb
Papcina said:
hi guys i have the following problem
i just replaced a new LCD+touchscreen on my 8125 (G3) and i can't connect it on ActiveSync... it simply wont recognize it.. even before i changed it i wasnt able to connect ppc to computer... but when i attach the usb to PC i hear the voice of something connected on USB port, and than the ballon pops out and says me the device was not properly connected...
i've tried changing older and newer ActiveSync's programs, they all function as same... when i press camera+soft reset (bootloader mode) i get the bootload mode and on the bottom i can see when i attach USB... but still it wont update any ROM to PPC... i even tried removing the mark from ActiveSync menu saying ''Allow USB Connection with this desktop computer'' but still it says me device not recognized... wtf?!?! I cant do nothing, upload ROMs neither browse...
please any help appreciated...
and yes, i tried hard reset too and i get the same... tomorrow ill go on 2nd PC to try on it but i have a feeling i'll get the same error there...
HELP!
thx bb
Click to expand...
Click to collapse
Which Windows are you at ? use winXP SP2,disable anti virus if any installed,also disable any firewall even windows own firewall.Disconnect phone from the usb cable and remove any sdcard if any.
Uninstall Active sync,Reboot Pc,open Windows Task Manager--->Processes Tab--->End wescomm.exe process.Reconnect phone via usb cable,get your phone into boot loader mode,check small usb appear a the bottom of bootloader screen and run the ruu...,hope it'll work out.
For Active sync connectivity,reinstall ,make sure no anti virus or firewall is running,connect phone with usb and let it synchronise.
Is your usb cable compatible,does it charge ?,if not,get a new usb cable. secondly, check if your mini usb port of your phone is working or it might be damaged.
Which Windows are you at ? use winXP SP2,disable anti virus if any installed,also disable any firewall even windows own firewall.Disconnect phone from the usb cable and remove any sdcard if any.
-->yes, win xp sp2, done all that already..
Uninstall Active sync,Reboot Pc,open Windows Task Manager--->Processes Tab--->End wescomm.exe process.Reconnect phone via usb cable,get your phone into boot loader mode,check small usb appear a the bottom of bootloader screen and run the ruu...,hope it'll work out.
-->nope, doesn't work dam...
For Active sync connectivity,reinstall ,make sure no anti virus or firewall is running,connect phone with usb and let it synchronise.
-->it won't crap...
Is your usb cable compatible,does it charge ?,if not,get a new usb cable. secondly, check if your mini usb port of your phone is working or it might be damaged.
-->tried several USB cables, all of them charge normally the unit.. i don't get where the f*** im making the mistake...
ok im really nuts now...
been on a 2nd pc, same problems there...
i can't do nothing with it! i tried even backing up on SD, but mtty won't connect... nothing... i have to cid unlock it, none ROMs work...
what the hell i do now? is there anyone in eastern/middle europe who can reflash the rom? i gave days and days for reading the forums and trying out to lock out this dam phone but i simply can, and i think i'll brick it in the wall
guys, any idea how can i get it over USB????
thx
b b
Papcina said:
ok im really nuts now...
been on a 2nd pc, same problems there...
i can't do nothing with it! i tried even backing up on SD, but mtty won't connect... nothing... i have to cid unlock it, none ROMs work...
what the hell i do now? is there anyone in eastern/middle europe who can reflash the rom? i gave days and days for reading the forums and trying out to lock out this dam phone but i simply can, and i think i'll brick it in the wall
guys, any idea how can i get it over USB????
thx
b b
Click to expand...
Click to collapse
Try this, on the 8125 run activesync, if you have partnerships there (IE. if the screed has "windows PC" on it), then go to "menu" on the lower right, then "Options" then select the "Windows PC" and delete it. Delete all partnerships that you have.
Then close activesync on the 8125 and go to "Start/setings/Connections/" and open your "connections". Do you have connections set-up? Make sure you have at least one connection set-up. Then close that and open your "USB to PC" is "Enable advanced network functionality" is the box checked? if it's not then check it (if it is then uncheck it), then connect your BSB cable and see if activesync on the PC will detect it.
If it does then set-up a new partnership.
Papcina said:
ok im really nuts now...
been on a 2nd pc, same problems there...
i can't do nothing with it! i tried even backing up on SD, but mtty won't connect... nothing... i have to cid unlock it, none ROMs work...
what the hell i do now? is there anyone in eastern/middle europe who can reflash the rom? i gave days and days for reading the forums and trying out to lock out this dam phone but i simply can, and i think i'll brick it in the wall
guys, any idea how can i get it over USB????
thx
b b
Click to expand...
Click to collapse
Well I think you have a damaged mini usb port of your phone,for info read this thread
http://forum.xda-developers.com/showthread.php?t=334440
I have been trying to resolve my AS Not Connected for a long time, over 1 year. I have tried all know recommendation/solutions to no avail.
Have read that FixASRunAT will fix the problem. Go to:
http://www.cs.pitt.edu/~jmisurda/ppc/FixASRunAt.zip
I downloaded it last night and will try reconnect tomorrow as I am out of town and cannot try AS now. iWill report back the results.
If this works for you, let us know. Wish you luck as I need it, too.
calouro said:
Try this, on the 8125 run activesync, if you have partnerships there (IE. if the screed has "windows PC" on it), then go to "menu" on the lower right, then "Options" then select the "Windows PC" and delete it. Delete all partnerships that you have.
Then close activesync on the 8125 and go to "Start/setings/Connections/" and open your "connections". Do you have connections set-up? Make sure you have at least one connection set-up. Then close that and open your "USB to PC" is "Enable advanced network functionality" is the box checked? if it's not then check it (if it is then uncheck it), then connect your BSB cable and see if activesync on the PC will detect it.
If it does then set-up a new partnership.
Click to expand...
Click to collapse
not working crap, i think now i have a damaged miniUSB..
i'll try to solve that by getting an BT dongle.. btw, is it possible to flash new ROM with BT?
@asctony i cant open that link, can u plz send me the file on my mail?
Papcina said:
not working crap, i think now i have a damaged miniUSB..
i'll try to solve that by getting an BT dongle.. btw, is it possible to flash new ROM with BT?
@asctony i cant open that link, can u plz send me the file on my mail?
Click to expand...
Click to collapse
Although it is possible to perform all actions with BT,like you do with normal active sync connectivity via usb,but No,You cannot flash a new rom through BT,you got to have a physical connectivity established between phone and your pc via usb and usb is shown at the bottom of the bootloader screen.Even during active sync connection,while flashing active sync is automatically disabled by the RUU and the flashing is still carried out by usb only.
crap... so the only logical solution that has left me is to give ppc to sum1 who will desolder/resolder the miniUSB connection back again... but still, i dont get it, i opened few times and i dont see any wire in miniUSB connector loosen or bricked... everything is fixed and on its place...
Papcina said:
crap... so the only logical solution that has left me is to give ppc to sum1 who will desolder/resolder the miniUSB connection back again... but still, i dont get it, i opened few times and i dont see any wire in miniUSB connector loosen or bricked... everything is fixed and on its place...
Click to expand...
Click to collapse
That's it !!!
there might be a tiny contact of the mini usb port which needs to solder,these tiny contacts are not sometimes visible to the naked eye,it can only be verified by checking with 'Voltmeter' and this can only be done by a person who has some knowledge about electronics repair and soldering.If you can do it,get a Voltmeter and can check the connectivity of all the five tiny connectors,good luck
dont worry i got this ****ing problem too
bootloader mode works but.....
I CANT CHARGE or CONNECT ON ACTIVE SYNC
BS!!!!!!
Mine will charge No Prob with both PC/USB Cable and Standard charger,PC takes FOREVER,It recongnizes a Smart Phone on both XP and Windows 7 but then says Not Installed correctly,No Drivers,ect. It has to be a Hardware issue with the Port or something,In "Comm Manager" there is always a "Check" Mark through the Activesync Selection,no way to get it to "enable" on the Phone Screen....Phone is not worth enough to hassle fixing it,it works fine,I have to use another phone to put stuff on my storage card,can I load windows 6.5 and unlock with the SD Card method?Thanks,Vegas
Happy New year to everybody...
Mine has started off bad, I just returned from my X-mas/New year break and I can no longer sync, install or uninstall programs ?
when I connect my PDA to the PC it sees it, but it can't sync, if I go to remove/add programs it shows empty nothing installed.
I can even brows the PDA but I can't copy files to or from it?
I'm lost, can anyone help me out on this I really don't want to do a hard reset.
Thanks.
Anyone.........?
tryed to reinstall active-sync?
did you installed some program has to do with network (kind of ftp-server or something else that uses some ports in you network-config)
i had the problem with filezilla ftp-server, using port 990 for ssl-authentification.
the problem was, active-sync also uses this port, but filezilla starting as service was bound to this, so AS could not work.
edi said:
tryed to reinstall active-sync?
did you installed some program has to do with network (kind of ftp-server or something else that uses some ports in you network-config)
i had the problem with filezilla ftp-server, using port 990 for ssl-authentification.
the problem was, active-sync also uses this port, but filezilla starting as service was bound to this, so AS could not work.
Click to expand...
Click to collapse
Hi Edi, No I haven't installed anything, but I think my problem might be something else (worse), I just realised that I can no longer copy move or delete files from either the PDA or the MC, I get an "access is denied" error.
Anyone have any idea what might have caused this? and better still, is there a fix.
I seem to be repeating myself lately with this answer, so I apologise if it seems down-right obvious, but have you ensured you have the latest version of ActiveSync/Windows Mobile Device Centre?
The reason I ask this is because I too was experiencing Sync problems using WMDV, but realised I didn't have the latest version (it doesn't automatically update with Windows Update, WTF?). Windows Mobile 6 is obviously programmed slightly different from revious versions, so updating Sync software is a simple step that's often missed...
Audio said:
I seem to be repeating myself lately with this answer, so I apologise if it seems down-right obvious, but have you ensured you have the latest version of ActiveSync/Windows Mobile Device Centre?
The reason I ask this is because I too was experiencing Sync problems using WMDV, but realised I didn't have the latest version (it doesn't automatically update with Windows Update, WTF?). Windows Mobile 6 is obviously programmed slightly different from revious versions, so updating Sync software is a simple step that's often missed...
Click to expand...
Click to collapse
Hi Audio,
Thanks for the reply, but I do have the latest version and I never had a problem with it until this week.
Just so i can try and help, what is it you are using Dave? AS or WMDV?
Audio said:
Just so i can try and help, what is it you are using Dave? AS or WMDV?
Click to expand...
Click to collapse
Hi Audio, I use both, AS at work and WMDV at home, both used to work fine.
And do you experience the issue on both?
EDIT: Apparently, there may be a problem with ActiveSync 4.5. Just take a look at this list of complaints about it lol.
One user stated:
"I was using AS4.2 with my ETen M700, everything was fine. I wanted to upgrade to WM6 and teh instructions said I needed to use AS4.5 I installed it and tried to connect my device - disaster! The rapimgr.exe process runs at 99% and slows the computer to a crawl.
After 3 attempts, I uninstalled it, and re-installed AS4.2 (available from www.microsoft.com) and now things are working again. "
This may be worth doing to see if this soilves your problem...
Audio said:
And do you experience the issue on both?
Click to expand...
Click to collapse
Yes I have tried it on three different machines, I can see the PDA but it won't sync or let me move or copy files.
It look like I might have to do a hard reset, but I'm hoping not
Also, a chap on a premium (you have to pay for support!) site said the following, which seems slightly similar:
"I've been using ActiveSync for a while now to sync outlook up to my motorola q. For some strange reason it's stopped working. The connection takes place, you get the little signal saying that ActiveSync picks up on it, the "Connecting" message, followed by the "Synchronizing" message... and nothing. It just hangs there. I've reinstalled ActiveSync and Outlook and did a hard reset on the phone. I'm convinced the issue is with the desktop, if I take the same PDA home, I'm able to sync up with my PC there. Does anyone know what happens during the Synchronizing phase and what could be possibly causing it to hang? ActiveSync 4.5 is a new beast, solutions to the older versions don't seem to apply.
If I hit the Stop button, ActiveSync hangs on the "Stopping" message and ActiveSync on the phone becomes unresponsive until I unplug the cable."
So even a Hard reset didn't solve this guys problems...
I would recommend uninstalling AS 4.5 from your machine, and installing 4.2. Reason being, i believe you need your phone connected to the computer when you install syncing software, so it more than likely "fiddles" with some very well hidden settings on the device. If this is the case, 4.5 may have [email protected] it up, but 4.2 may be your savior.
If you decide to give it a go, let us know how it goes...
Audio said:
Also, a chap on a premium (you have to pay for support!) site said the following, which seems slightly similar:
"I've been using ActiveSync for a while now to sync outlook up to my motorola q. For some strange reason it's stopped working. The connection takes place, you get the little signal saying that ActiveSync picks up on it, the "Connecting" message, followed by the "Synchronizing" message... and nothing. It just hangs there. I've reinstalled ActiveSync and Outlook and did a hard reset on the phone. I'm convinced the issue is with the desktop, if I take the same PDA home, I'm able to sync up with my PC there. Does anyone know what happens during the Synchronizing phase and what could be possibly causing it to hang? ActiveSync 4.5 is a new beast, solutions to the older versions don't seem to apply.
If I hit the Stop button, ActiveSync hangs on the "Stopping" message and ActiveSync on the phone becomes unresponsive until I unplug the cable."
So even a Hard reset didn't solve this guys problems...
I would recommend uninstalling AS 4.5 from your machine, and installing 4.2. Reason being, i believe you need your phone connected to the computer when you install syncing software, so it more than likely "fiddles" with some very well hidden settings on the device. If this is the case, 4.5 may have [email protected] it up, but 4.2 may be your savior.
If you decide to give it a go, let us know how it goes...
Click to expand...
Click to collapse
Hi Audio, I don't know what to do, I started another thread about no longer being able to either copy, move, delete, install or uninstall anything, I really don't think it's a sync problem anymore. I will wait another day or so and then I'm going clear storage and start again.
what really pisses me off is my wife has no problems at all? perhaps my PDA is ******.
Exactly the same has just happened to me - I tried to connect to ActiveSync this morning to copy a file across via bluetooth, but it refused to connect. I plugged in the USB cable, nothing - the phone charges but ActiveSync does not want to know.
I deleted the device in AS, tried to add a new one - nothing found.
I last sync'd up fine 4 days ago.
I am using Dutty's DualTouch v1.1 release.
I am using AS 4.5.0 build 5096
If I discover services via BT from the kaiser to the computer it finds the ActiveSync service.
I have done a soft reset, no difference, restarted the PC, same. I haven't applied any Windows Updates or made any changes since it stopped working.
I might try rolling back to AS 4.2
Edit: Same with AS4.2
Think it might be clear storage time
Cleared storage and then it worked fine...will take the opportunity to upgrade to dualtouch v2
Hi Blaze, damn it's annoying isn't it, my next move is clear storage as well.
Hope mine works again.
It's bloody happened again I reflashed the rom with Duty's Dual Touch V2. Much better rom, but activesync has just given up again via BT and usb. Maybe it's some inherent problem with WM, or with Duty's roms - which are you using Dave?
I've tried it on a fresh build of XP Pro on an old machine with nothing than AS & Outlook 2k3 on - same, AS sees the device, but wont sink. Problem seems with the device...
Dave... said:
perhaps my PDA is ******.
Click to expand...
Click to collapse
Sorry I cant help other than to say my dutty rom is working fine on WMDC.
But I had to post and ask why you asterisked out the "ed" and left the lrest of the word in?
Brilliant! Lmao! :d:d:d
unwired4 said:
Sorry I cant help other than to say my dutty rom is working fine on WMDC.
But I had to post and ask why you asterisked out the "ed" and left the lrest of the word in?
Click to expand...
Click to collapse
Good Point I didn't even notice, put it down to stress...
PS: For anyone who's interested, I ended up doing a hard reset, reinstalled my apps, restored my backups and it's working fine now.
Did you have F-secure Mobile installed? If not, I could take that away from possibilities that's causing this problem
hey guys,
im new here and its also my first ppc.
ive got the following problem:
me (or my ppc) is not able to connect with activesync...
wtf can i do??
plz help me, thx,
LuFo
Install AS 4.5
Then connect your phone. Windows will first detect it as a new USB device and then AS will kick in and ask to set up a partnership.
Exactly what is going wrong with yours?
so, here we go:
ive got as 4.5 on my pc and ive recognized also that some other guys (even with older as) could connect to my ppc...
so, what is thie fckn prob??
again: plz help, what should i do?
greetz
PaulusUK said:
Install AS 4.5
Then connect your phone. Windows will first detect it as a new USB device and then AS will kick in and ask to set up a partnership.
Exactly what is going wrong with yours?
Click to expand...
Click to collapse
ok, i connest my ppc to the pc, its asking:
harddrive
or
as,
im typing as and its saying there isnt installed as 4.5
and the pc sais: no connection do u want to start the fixing??
(everythings translated by myself from german, plz ignore the faults)
grtz
i read that if you're using a usb hub it would not connect. you must have the usb cable connect straight to your pc's usb port.
and if nothing works the last solution is to hard reset your pocket pc for a frest start and see if it can connect then.
LuFo Diamond said:
ok, i connest my ppc to the pc, its asking:
harddrive
or
as,
im typing as and its saying there isnt installed as 4.5
and the pc sais: no connection do u want to start the fixing??
(everythings translated by myself from german, plz ignore the faults)
grtz
Click to expand...
Click to collapse
untick the advanced network functionality in the connection settings USB to PC and try again ...
swampy said:
i read that if you're using a usb hub it would not connect. you must have the usb cable connect straight to your pc's usb port.
and if nothing works the last solution is to hard reset your pocket pc for a frest start and see if it can connect then.
Click to expand...
Click to collapse
2nd that. Try another USB port on your PC. Sounds like there's either the driver missing (which should only be the case if you do not have Active Sync installed)
OR
try to disable the "Advanced network functionality". Can be found at 'Settings > Connections > USB to PC'. (Einstellungen, Verbindungen, USB zu PC oder so).
Do you have some sort of firewall software?
like, ZoneAlarm or antivirus with firewall?
disable them or allow the port as trusted and you should be fine
jeah,
thanks for this many posts, but ive got all these probs outa my way, these are all the things ive thought they may disturb the connection... but (im sorry) theyre no solution for my fckn prob, as told, my ppc connects to other pcs(with older as)but not to mine with the newest as ...
so, lets think how to manage it...
try rebooting the host PC or just kill mobsync.exe, wmdc.exe and WmdHost.exe in taskmanger. Then open Sync software again. Works for me.
thats an answer
thx a lot, ill try tomorrow...
all the wa<y, sometimes, when i stay the ppc connected and reboot my pc it works, but dont sync anything, its just "connected"...
ill try and post my answer soon.
LuFo Diamond said:
jeah,
thanks for this many posts, but ive got all these probs outa my way, these are all the things ive thought they may disturb the connection... but (im sorry) theyre no solution for my fckn prob, as told, my ppc connects to other pcs(with older as)but not to mine with the newest as ...
so, lets think how to manage it...
Click to expand...
Click to collapse
what OS do u have on your PC?
Did you download the newest WMDC also,
just checking http://www.microsoft.com/windowsmobile/en-us/downloads/microsoft/device-center.mspx
here it is
LuFo Diamond said:
thats an answer
thx a lot, ill try tomorrow...
all the wa<y, sometimes, when i stay the ppc connected and reboot my pc it works, but dont sync anything, its just "connected"...
ill try and post my answer soon.
Click to expand...
Click to collapse
I think i have found a solution for you.
Follow:
Start Menu > Configuration > Connections > Click on the icon called "USB à ordinateur" (my phone is in french so i think it will be for you " USB" or "USB to PC")
It's written: Choose the connection type to PC
Select active Sync and uncheck the case just under (it is " activate the feature advanced networking")
And that is !!
TRY and say me..
Hi the diamond is my first PPC as well. I connected it in my PC and was able to use it as a HD. however i am having doubts of just unplugging it afterwards but i did just unplugged it after use.
On my second attempt. Diamond notified me if i will sync or use the HD i accidentally hit sync. but it required a password. I unplugged it and the problem beginned.
There is no Start Menu. so i did the soft reset on the red button below the stylus. It worked now, however the home screen does not have the Large Digital Clock now.
Can someone help me to display it back i have tried to check it in the Today menu. however it is still not appearing.
Pls.. help a new PPC user. Thank you.
cJosephaq said:
Hi the diamond is my first PPC as well. I connected it in my PC and was able to use it as a HD. however i am having doubts of just unplugging it afterwards but i did just unplugged it after use.
On my second attempt. Diamond notified me if i will sync or use the HD i accidentally hit sync. but it required a password. I unplugged it and the problem beginned.
There is no Start Menu. so i did the soft reset on the red button below the stylus. It worked now, however the home screen does not have the Large Digital Clock now.
Can someone help me to display it back i have tried to check it in the Today menu. however it is still not appearing.
Pls.. help a new PPC user. Thank you.
Click to expand...
Click to collapse
Try the search engine before you post, recently there where alot of topics on ActiveSync not working. Anyway, the way your PPC will act when you connect it to a USB port can be setup in setting, connections, usb to pc. Mark Diskdrive or ActiveSync.
There you should also unmark the advanced network functionality. Check it off and try again.
Rgds,
Thanks, by the way do you know how to display the Large Digital Clock again in Home. It was lost after i tried to soft reset my hanging Diamond.
Do you think it will appear again if i do a Hard Reset? Thanks.
cJosephaq said:
Thanks, by the way do you know how to display the Large Digital Clock again in Home. It was lost after i tried to soft reset my hanging Diamond.
Do you think it will appear again if i do a Hard Reset? Thanks.
Click to expand...
Click to collapse
A Hard Reset should bring it back to it's default value so yes I see no problem there ...
Blazeitup123 said:
try rebooting the host PC or just kill mobsync.exe, wmdc.exe and WmdHost.exe in taskmanger. Then open Sync software again. Works for me.
Click to expand...
Click to collapse
THX a lot, but all these programs are NOT running, ive tryed to run them and its juts possible tu run mobsync.exe mannually...
so this way would not work for me,
im sorry
on6hp said:
what OS do u have on your PC?
Did you download the newest WMDC also,
just checking http://www.microsoft.com/windowsmobile/en-us/downloads/microsoft/device-center.mspx
Click to expand...
Click to collapse
my pc works with xp prof sp3
abinan said:
I think i have found a solution for you.
Follow:
Start Menu > Configuration > Connections > Click on the icon called "USB à ordinateur" (my phone is in french so i think it will be for you " USB" or "USB to PC")
It's written: Choose the connection type to PC
Select active Sync and uncheck the case just under (it is " activate the feature advanced networking")
And that is !!
TRY and say me..
Click to expand...
Click to collapse
jeah, this possibility is also told as the first option but , im sad, not the solution...
greetz
Hi,
I am getting a bit frustrated over this.
When I connect my X1 to my Vista x86 nothing happens (well the USB task tray icon show for about a second and vanishes again).
When I disable the "advanced option" in the USB/PC connection settings in the X1 I at least get a USB connection with something identified as "PocketPC USB Sync".
Any idea why this is happening and how I can get a real connection with the win mobile device center?
Thanks for helping me out!
Cheers,
Tillman
maybe give this a try:
http://modernnomads.info/wiki/index.php?page=Windows+Mobile+Device+Center+Troubleshooting
I've once had the issues of not able to connect my Windows Mobile device with vista too, and it can get very annoying.. good luck with it.
You might want to try and disable the firewall and then connect the device. I had this problem with Sygate Personal Firewall (sygate was bought by symantec and personal firewall is now terminated and no longer available)
Thanks for the quick response guys!
I already tried disabling the firewall (nod32) but that did not help.
Also checked all services - everything is peachy in that department.
But still - no connection.
When I switch back to "legacy mode" (disabling the advanced option in usb/pc settings on the device) then the device will tell me that I need to install active sync 4.5 or higher and wmdc still does not connect.
This is really strange...and annoying and the same time.
Any more ideas or any way for me to debug what's going on?
Thanks for you help!
Have you intalled "Windows Mobile Device Center 6.1" on your Vista-PC?
The MobileDeviceCenter should be standard without the need to install...
At my Vista Home the X1 had no problems to connect.
Open the Mobile Device Center and delete all old connections of other PPC. Then start your PC again, Softreset your X1 and try again. This should help. I had the problems too, when first connecting, because he didn't liked my G900-connection which was first
After this I too could install my G900 again and no problems since yet (2 weeks).
pf said:
The MobileDeviceCenter should be standard without the need to install...
At my Vista Home the X1 had no problems to connect.
Open the Mobile Device Center and delete all old connections of other PPC. Then start your PC again, Softreset your X1 and try again. This should help. I had the problems too, when first connecting, because he didn't liked my G900-connection which was first
After this I too could install my G900 again and no problems since yet (2 weeks).
Click to expand...
Click to collapse
Well sometimes the Mobile Device center could stuff up or not work due to some issues such as installation of Mobile Device Center 6.1 went wrong. I have experienced that I think I didn't follow the procedures correctly and things just wouldn't work. Eventually I had to do some uninstall and reinstall many times to finally get it working.
When I first plugged mine it it installed some drivers but didn't show up in the Mobile Device Center; unplugging and replugging in caused it to work...did you change settings in between plugging in for the second time?
What I have tried so far (and nothing worked):
Uninstall / reinstall WMDC
Uninstall / reinstall Win Mobile Remote Adapter (yes, this does show up once I am connected with "advanced" USB mode)
Uninstall / reinstall "PocketPC USB Sync" (shows when X1 is set to legacy USB mode)
When in "advanced" mode I can also see a new LAN connection showing up in network overview.
The same X1 on a different Vista 32bit right next to this one will connect just fine. So it's definitely about a driver or config thing with this Vista.
This is driving me...well you know what.
btw, you did try restarting your comp when performing some of those steps, and you did try different USB ports right?
I know that you had to ask.
Yes I did. I have rebooted the system several times in between all those reinstallation tasks.
By the way. When I am in USB legacy mode and reconnect the USB cable then the X1 will show a messagebox telling me that it's connecting with the host and that the user credentials / user account (having to translate here) are correct.
But still NO connection visible in WMDC.
I had the same problem with my X1. I assumed that because my HTC Diamond worked the X1 would as well.
I finally installed WMDC from the SE install cd, and bingo!! al good. Hope it works for you...
Wow!
Even though it does not work (yet) it's showing some new signs.
Installing WMDC from SE disc fails at 99% progress and then rolls back.
There's gotta be some installation error log this, right?
Thanks for coming up with that suggestion. Really, I should try installing from vendor CDs more often instead of hunting down the latest version on the net.
TillmanZ said:
Wow!
Even though it does not work (yet) it's showing some new signs.
Installing WMDC from SE disc fails at 99% progress and then rolls back.
There's gotta be some installation error log this, right?
Thanks for coming up with that suggestion. Really, I should try installing from vendor CDs more often instead of hunting down the latest version on the net.
Click to expand...
Click to collapse
maybe give event viewer a try and check under Windows Logs (not sure if it will be application or system tho)
just in case you aren't sure, in vista either type in "Event Viewer" in the start menu search bar, or type in "eventvwr"
Don't you just like vista?
That helped (to install SE's WMDC). The issue was that my HTC Universal was still connected to one USB port (for testing purposes since that device is not recognized either).
As soon as I unplugged the HTC I was able to complete the WMDC installation.
Unfortunately though it still won't connect to my X1.
Any more ideas?
what is your settings in Windows Mobile Device Center connection Settings?
Well here is my settings that is working with my x1:
Allow USB connections checked
Allow connections to "DMA"
This computer is connected to "Automatic" (this shouldn't matter)
Allow automatic device authentication checked
Allow data connection on device when connected to PC (this shouldn't matter either)
also, while this link was in the first link that I have posted for trouble shooting, just want to make sure you actually tried The offical Windows Mobile Device Center troubleshooting guide?
http://www.microsoft.com/windowsmobile/en-us/help/synchronize/device-center-troubleshooting.mspx
namely these steps:
Quote"
If Windows Live OneCare is installed on your machine, it may be blocking the device connectivity. Please click here for the steps to configure Windows Live OneCare to allow the device to connect.
My device wasn’t connected during this installation.
While it is not a strict requirement that you have a device connected during the installation process of Windows Mobile Device Center, we highly recommend that you do.
"
I didn't have the DMA set (changed that now). Everything else already was like you described and it does not work.
This really freaks me out. I always hated my iTunes/iPhone connectivity but that honestly works much smoother. Of course I do understand that this behavior is non standard as I have experienced myself that the phone works with my other Vista machine but that does not really help me here.
Any update on this? I am having the same problem.
I'm having the _exact_ same problem too, but in Vista x64. I don't know why WMDC can be such a c**t sometimes, as I have never been able to 'sync' with my Media Center PC.
My only saving grace is that my laptop has Bluetooth, and syncing works great on it. I have never had success connecting the USB cable (with many options changed around of course) to either of these computers. Only Bluetooth syncing works for me...
Hopefully we can find the answer!
What USB cable are you using??? the one that came with Xperia??? Cos the one that came with my Xperia never worked out of the box, it could only charge...
I also got another extra cord which came in another box, that worked fine for both syncing and transferring data until today, now it says USB device not recognized, maybe I was trying the flash X1 with new ROM through SEUS, did the whole lower volume key and power button to get the 3 strips.
Now I am using the USB cable that came with my external HDD, that's currently working, hopefully it won't fail me.
so any ideas??? I don't want to keep changing cables...