Related
Hei all.
After reading through the forums hour after hour I finally give up
I got my german O2 XDA Mini s here
IPL 2.21
SPL 2.21
GSM 02.19.11
OS 2.21.4.2
I want to up/downgrade to the Qtek 2.18 NOR ROM. But the big Problem is that if I connect to PDA to my laptop via USB it is not recognized?! Also on a other laptop it didn't work, although it worked earlier. Even a hard reset couldn't help it.
Second thin I read is that Wizards with SPL/IPL 2.21 or higher can't be flashed with a other ROM then a Provider update.
But now I found this thread: http://forum.xda-developers.com/showthread.php?t=271043 were it is made possible. I made my new ROM image. Now I only need to bring it on my miniSD Card und make the XDA load it from there. And that's my problem. How do I make a "bootable" SD Card und make the XDA a boot from there? I only found I manual for the Magician....
Would be great if someone could help me!!!
Good morning
New Day, new chance. Anybody with an idea?
press and hold down the Camera button then jab the Reset hole will bring the device into Bootloader mode, connect to your Laptop and have a try.
for reflash from a SD card containing rom image, press and hold down the Camera and VoiceDial key simultaneously, jab once the Reset hole, then, release the Camera key FIRST, keep VoiceDial pressed until sth like below showing on the PPC screen:
[FONT=宋体]Restore ALL image from SD[/FONT]
[FONT=宋体]Press Voice Dial Key[/FONT]
[FONT=宋体]to Start Download[/FONT][FONT=宋体] [/FONT]
[FONT=宋体]Download SD image?[/FONT]
[FONT=宋体][/FONT]
[FONT=宋体]then, press VoiceDial key.[/FONT]
[FONT=宋体][/FONT]
[FONT=宋体]this procedure is worked for my qtek9100, although both qtek9100 and o2xdaminis are both "Wizard", i have no idea whether it should work, just give a try and god bless.[/FONT]
what files need to be on the SD card? Do they need to named something special for the wizard?
there's no "files" on the SD card, i said, it's only "rom-image".
huangyz said:
press and hold down the Camera button then jab the Reset hole will bring the device into Bootloader mode, connect to your Laptop and have a try.
for reflash from a SD card containing rom image, press and hold down the Camera and VoiceDial key simultaneously, jab once the Reset hole, then, release the Camera key FIRST, keep VoiceDial pressed until sth like below showing on the PPC screen:
[FONT=宋体]Restore ALL image from SD[/FONT]
[FONT=宋体]Press Voice Dial Key[/FONT]
[FONT=宋体]to Start Download[/FONT][FONT=宋体] [/FONT]
[FONT=宋体]Download SD image?[/FONT]
[FONT=宋体][/FONT]
[FONT=宋体]then, press VoiceDial key.[/FONT]
[FONT=宋体][/FONT]
[FONT=宋体]this procedure is worked for my qtek9100, although both qtek9100 and o2xdaminis are both "Wizard", i have no idea whether it should work, just give a try and god bless.[/FONT]
Click to expand...
Click to collapse
Thanks Huang!
I'm nearly there
No the only problem left is to prepare the bootable SD-Card. If wanted to use the XDAtools http://forum.xda-developers.com/showthread.php?t=219261&page=7&highlight=create+rom+image
If I didn't missunderstand it, this should solve my problem. But when I give my nk.nbf made in the first thread as a input file the XDA OS Image Tool tells me that it is an unsupported file format and it doesn't know how to open it
I just unpacked the Tools and registered them. Is there anything mor I have to do to make me a SD-image?
Ok, nex step. When I go into the Bootloader, i get an USB connection. Hell knows we not in normal mode :-/
But this forum is just too big I couldn't find a way to get a new ROM to my Wizard in this way...
dfc-neo said:
Ok, nex step. When I go into the Bootloader, i get an USB connection. Hell knows we not in normal mode :-/
But this forum is just too big I couldn't find a way to get a new ROM to my Wizard in this way...
Click to expand...
Click to collapse
From here you can run the Rom Update Utility on your PC and it will flash your device.
Ok, that easy? But it doesn't work :-(
I get the connection, tested it with a terminal, it is realy connected.
- When I use the RUU from risidoro (see my first post up here) I get ERROR [300] STRUMENTO DI AGGIORNAMENTO NON VALIDO. I'd guess that means something me device is not valid???
- If I want to flash with RUU_Prodigy_2180704_21807104_20710_QTEK_NOR_Ship.exe it also connects and all that stuff, but then it told me my nbf file is too old. (I got SPL/IPL 2.21 ) ERROR [296]
- If I extract this RUU manually and replace the nbf with the one handmade, and start ROMUpdateUtility.exe I get ERROR [238], can't open the file.
Search for this file 'ROMUpdateUtility_Wizard_NoID.exe'
It will think that your phone has Rom version 1.2 on it and thus will allow you to flash any Rom image.
yeah, thats what I tried first and got ERROR [300] and this Italian Error message
I would be very interested in this since my USB connector broke. Hope you find the answer for this. Anyways, I was able to do an upgrade of OS and downgrade it using awizard via BT connection in my CID locked phone.
How did you do that?? Because if I try to update via Bluetooth I always get Errors :-/
BT update
Well, actually I did a backup of everything using Awizard (via USB when my connector was working) and then I updated just the OS using some tools. Here is the link http://forum.xda-developers.com/viewtopic.php?t=56088&start=0. Then I rename the extension to nba so awizard can read it and then used awizard to update only the OS. This was all with USB cable. Then my toddler got a hold of my phone while charging and broke the USB connector.
Got sick of the 3.2 rom then took the risk of downgrading to my old OS via awizard using BLUETOOTH. It took some time to update and have to make sure my phone don't turn off during update. Anyways, now I have the 2.26 OS back.
ionutzu said:
Hi there,
I installed a bunch of stuff on the AKU3.2 Rom H-tec innov / O2 ROM which i found on the ftp and now when i soft-reset the phone, it either gets stuck (in windows) on Today, where it only loads like half of it and is consequently stuck or it resets again...
How would I be able to solve this issue having that it doesn't connect to ActiveSync?
Thanks a bunch,
John
Click to expand...
Click to collapse
ionutzu said:
OK let me clarify.... phone is totally unresponsive. I turn it on, HTC Innovation screen pops then the O2 with all the version, it loads windows and you can't really do anything but turn it off... or hard reset which doesn't help because the next time it loads, it just does the same thing...
What can I do
Click to expand...
Click to collapse
Thought it might've been in the wrong section!
Try to put it in bootloader mode and reflash. Goodluck!
clemsyn said:
Try to put it in bootloader mode and reflash. Goodluck!
Click to expand...
Click to collapse
Thanks for your reply, could you direct me please to somewhere where i can read of how to put it in bootloader mode? I have no idea and I can't find it in the manual. Thanks
If you want, you can IM me on YIM: ionutz_ceo
Thanks a lot
I've achieved putting it into bootloader mode, how would I go about reflashing now?
lol, ok!
So basically this is the result of my 2 hour research::
If you're Wizard is frozen, you do this:
1. Turn off USB in ActiveSync
2. Download mtty
3. While phone is off, press Camera button then holding it press Power button on phone and it will load in bootloader mode
4. Connect mtty to the phone via usb
5. <<< Here is when my research parts ways
6a. You can use a sd card and put an image on it, using mtty reflash the phone (don't know how to do that or where to get the image)
6b. There's another way of reflashing the phone...
Can anyone fill me in on that?
ionutzu said:
lol, ok!
So basically this is the result of my 2 hour research::
If you're Wizard is frozen, you do this:
1. Turn off USB in ActiveSync
2. Download mtty
3. While phone is off, press Camera button then holding it press Power button on phone and it will load in bootloader mode
4. Connect mtty to the phone via usb
5. <<< Here is when my research parts ways
6a. You can use a sd card and put an image on it, using mtty reflash the phone (don't know how to do that or where to get the image)
6b. There's another way of reflashing the phone...
Can anyone fill me in on that?
Click to expand...
Click to collapse
That seems a bit more complicated than what is really needed.
Assuming that your device was a G3 before you started, you are CID unlocked and you didn't overwrite incompatible bootloaders on a G4 device by using a G3 only ROM:
Once you are in bootloader, connect your USB cable. You should see the letters USB in the lower corner of your device.
Reflash with an official AKU2 ROM (latest available from your carrier's website.)
to do this once you are in bootloader mode and see USB in the lower corner execute the rom installer.
Don't flash an AKU3 Rom until you read all the threads completely on them. Several programs that work with AKU2 do not work with AKU3 and will freeze your device - Which appears to be what you are experiencing. There is still work being done on AKU3 and they aren't for mainstream use yet. There are driver incompatibilities, database restructures and such that haven't been accounted for in some software. The most common issues are documented repeatedly in every AKU3 ROM thread.
Zzan said:
That seems a bit more complicated than what is really needed.
Assuming that your device was a G3 before you started, you are CID unlocked and you didn't overwrite incompatible bootloaders on a G4 device by using a G3 only ROM:
Once you are in bootloader, connect your USB cable. You should see the letters USB in the lower corner of your device.
Reflash with an official AKU2 ROM (latest available from your carrier's website.)
to do this once you are in bootloader mode and see USB in the lower corner execute the rom installer.
Don't flash an AKU3 Rom until you read all the threads completely on them. Several programs that work with AKU2 do not work with AKU3 and will freeze your device - Which appears to be what you are experiencing. There is still work being done on AKU3 and they aren't for mainstream use yet. There are driver incompatibilities, database restructures and such that haven't been accounted for in some software. The most common issues are documented repeatedly in every AKU3 ROM thread.
Click to expand...
Click to collapse
Yes I agree with this the other option is a bit more complicated. This is much easier
@ ionutzu
Please update how the solutions above worked for ya. Zzan's solution is standard and most used along with being the easiest & should definitely work.
^^ you guys are wonderful!
Pretty much this is how it works, I couldn't find the "easy" solution anywhere, but now I figured it out.
1. Turn on phone holding camera button + power button
2. Connect via USB
3. Make sure USB is written in bottom left corner of PPC screen
4. Run an original ROM update (that is, the ones coming straight from T-Mob, I've tried it with other roms, it doesn't work)
5. It should work, you should have a fresh copy
6. I guess put your customized rom and try again....
Thanks for the help.
ionutzu said:
^^ you guys are wonderful!
Pretty much this is how it works, I couldn't find the "easy" solution anywhere, but now I figured it out.
1. Turn on phone holding camera button + power button
2. Connect via USB
3. Make sure USB is written in bottom left corner of PPC screen
4. Run an original ROM update (that is, the ones coming straight from T-Mob, I've tried it with other roms, it doesn't work)
5. It should work, you should have a fresh copy
6. I guess put your customized rom and try again....
Thanks for the help.
Click to expand...
Click to collapse
Glad it worked out for you.
At 56%, the desktop went to a blue screen and said an error had occurred and the system must be restarted. The screen asked if I had installed any new programs, check with the adminstrator, etc. The only program recently installed is the program for this ROM revision. When it crashed, the phone had a completion bar in the top 1/3rd, showing 56% completion. The rest of the screen was white. I restarted the desktop and was unable to establish a sync connection. I then preformed a hard reset on the phone. When it restarted, it showed 4 color bars, red on top, green, blue and white at the bottom. Since I cannot restablish a sync connection, how do I finish the modification. I am now concerned that I have "bricked" the phone. I am reluctant to try this mod on another phone until I can determine what went wrong.
Adding additional info
My phone is a G3, CID and SIM are unlocked, desktop is using Windows XP, SP2 and ActiveSync is Ver. 4.5.0
phone isnt bricked, your getting into bootloader fine. you need to turn it on, get it into bootloader i mean. if needbe press camera and soft reset (power button) then plug it in USB. You then need to flash your phone with the operator ROM, or the ROM you want to flash it with. Your phone is by far bricked, G3 ones are really difficult to ruin. I learnt that first hand
http://forum.xda-developers.com/showthread.php?p=1560272#post1560272
Think I may have done just that...bricked my phone. G3 wiza200, IPL/SPL 2.26
Cannot get it to read a usb connection at all. Help please?? Thanks in advance
jphuffs said:
At 56%, the desktop went to a blue screen and said an error had occurred and the system must be restarted. The screen asked if I had installed any new programs, check with the adminstrator, etc. The only program recently installed is the program for this ROM revision. When it crashed, the phone had a completion bar in the top 1/3rd, showing 56% completion. The rest of the screen was white. I restarted the desktop and was unable to establish a sync connection. I then preformed a hard reset on the phone. When it restarted, it showed 4 color bars, red on top, green, blue and white at the bottom. Since I cannot restablish a sync connection, how do I finish the modification. I am now concerned that I have "bricked" the phone. I am reluctant to try this mod on another phone until I can determine what went wrong.
Click to expand...
Click to collapse
hi
ur phone is certainly not bricked,cuz ur desktop crashed therefore the phone upgrade cudn't be completed,nothing to worry as long u can get to bootloader mode(Tricolor Screen)
Ok,listen, u do not require active sync connection,to flash a rom,do as I say and it'll be working fine,follow these steps to complete ur upgrade:-
1.Switch on,go to bootloader mode (Tri colored screen).
2.Connect usb cable to the phone and PC
3. After connecting usb cable,u will notice small 'usb' showing on the corner at the bottom of the bootloader screen of ur phone,if it shows,ur r ready to flash and upgrade
4.start the upgrade RUU_ rom u want the to upgrade with
5. complete the flash,let it reboot
let me tell u,u dont need active sync connection to upgrade
cheers
akashastrega said:
http://forum.xda-developers.com/showthread.php?p=1560272#post1560272
Think I may have done just that...bricked my phone. G3 wiza200, IPL/SPL 2.26
Cannot get it to read a usb connection at all. Help please?? Thanks in advance
Click to expand...
Click to collapse
hi
i have read ur situation at thread u have mentioned here,well i can assure u it's not bricked,cuz as sometimes it's able to go to bootloader mode.
The only problem to me seems the usb connectivety problem.
does it charge ?,if not then clearly it' a usb connectivity,if u can manage to get another usb cable and check out,hope it wud clear this doubt
zabardast_1 said:
hi
ur phone is certainly not bricked,cuz ur desktop crashed therefore the phone upgrade cudn't be completed,nothing to worry as long u can get to bootloader mode(Tricolor Screen)
Ok,listen, u do not require active sync connection,to flash a rom,do as I say and it'll be working fine,follow these steps to complete ur upgrade:-
1.Switch on,go to bootloader mode (Tri colored screen).
2.Connect usb cable to the phone and PC
3. After connecting usb cable,u will notice small 'usb' showing on the corner at the bottom of the bootloader screen of ur phone,if it shows,ur r ready to flash and upgrade
4.start the upgrade RUU_ rom u want the to upgrade with
5. complete the flash,let it reboot
let me tell u,u dont need active sync connection to upgrade
cheers
Click to expand...
Click to collapse
I just had this happen to me as well, I got stuck a 29%
Now when I get to bootloader it shows the IPL 2.26 and SPL 2.26 and also a RUU in the top right hand corner. Plug in USB and I get USB at the bottom left but then when I try to launch the RUU with the rom I want to flash I Invalid update tool, download new tool... It wont "Verify information on the device"
**EDIT
Nevermind, I just got Titanium to take... I may be ok... I think the RUU in the vanilla download I got is messed up or something...
Currently ripping through the rom update now. Damn I just got this phone yesterday I was gonna be pissed if I killed it.
Okay, I have the tricolor screen with IPL 2.25 on the left top of the red bar, SPL 2.25 on the left bottom of the red bar, RUU on the right top of the red bar and USB on the bottom left of the screen.
I push the camers button, do a soft reset and launch the ROM update. First window says "Verifying information on your PDA phone. Please wait." After a few moments I get a window that says "ERROR (300) This update utility cannot be used for your phone. Please get newer update utility."
If I try again, I get a window with "ERROR (264) CONNECTION" And an additional message about the USB connection not working. I am using a USB charge/sync cable and not a cradle.
What now?
jphuffs said:
Okay, I have the tricolor screen with IPL 2.25 on the left top of the red bar, SPL 2.25 on the left bottom of the red bar, RUU on the right top of the red bar and USB on the bottom left of the screen.
I push the camers button, do a soft reset and launch the ROM update. First window says "Verifying information on your PDA phone. Please wait." After a few moments I get a window that says "ERROR (300) This update utility cannot be used for your phone. Please get newer update utility."
If I try again, I get a window with "ERROR (264) CONNECTION" And an additional message about the USB connection not working. I am using a USB charge/sync cable and not a cradle.
What now?
Click to expand...
Click to collapse
ok when u swith on the phone what happens ?
does it go to bootloader mood ? or u force it to go bootloader by keeping camera button pressed and doing soft reset ?
well,after geting to bootloader mode,don't reset again just establish usb connectivity and when it show usb in the lower part of the bootloader screen launch ruu and start the flash.if it still stops with an error,post that error,then it means u had a bad flash or no flash at all.are you pretty sure you got it CID unlocked ?
tell you what you do,go to this link download WST tool and apply it,than post the data info it gives here,this will give the present status of your phone,ok
http://forum.xda-developers.com/showthread.php?t=329170
read this sticky:http://forum.xda-developers.com/showthread.php?t=298613
jphuffs said:
Okay, I have the tricolor screen with IPL 2.25 on the left top of the red bar, SPL 2.25 on the left bottom of the red bar, RUU on the right top of the red bar and USB on the bottom left of the screen.
I push the camers button, do a soft reset and launch the ROM update. First window says "Verifying information on your PDA phone. Please wait." After a few moments I get a window that says "ERROR (300) This update utility cannot be used for your phone. Please get newer update utility."
If I try again, I get a window with "ERROR (264) CONNECTION" And an additional message about the USB connection not working. I am using a USB charge/sync cable and not a cradle.
What now?
Click to expand...
Click to collapse
download the wizar-love rom
flash it using the ruu provided..
ftp://xda:[email protected]_Novii+CF2.rar
it should work.....
read this sticky
http://forum.xda-developers.com/showthread.php?t=298613
G4.1 Does you're device start normally (yes) or is it stuck on the three-colored bootloader screen (no)? YES... go to step G4.4, NO go to step G4.2
G4.2 Turn off you're device totaly. Remove the SD card and disconnect the USB cable from you're device. Turn on the device while holding the camera button. You will get into bootloader mode (3 colored screen). Connect the USB cable to the computer and you will see USB at the bottom of your screen above the left softkey (Activesync will not connect in bootloader mode, but you can flash from this screen!). go to G4.3
G4.3 Download wizard_love rom and flash it to your device. Your device should startup again after doing this. Go to G4.4.
G4.4 Is your device CID-unlocked (note: it's not the same as SIM-unlocked!)? YES... go to step G4.7, NO OR DON'T KNOW go to step G4.5. (note: CID-unlocking a G4 is only possible by paying for it at imei-check!)
G4.5 Download enable-rapi.zip. Transfer Cert_SPCS.cab and EnableRapi.cab to your phone. Run Cert_SPCS.cab FIRST and EnableRapi.cab SECOND. Turn your device off and on or wait 5 minutes before soft resetting. Done? Go to G4.6.
G4.6 Follow this great thread by the-equinoxe: [solution] G4 SoftSPL Flash any ROM to CID locked G4 [UPDATED] and load the softSPL on your device using his method. Make sure you take a G4 safe rom (see the thread for details). After the steps you'll have the rom of your choise on your device!
G4.7 You're reade to flash the AKU2, AKU3, WM6 rom of you're choise IF the rom DOESN'T contain IPL/SPL. AKU3 and WM6 roms normally don't contain IPL/SPL. If you want to flash an AKU2 rom, make sure you take the G4 version. If you get an error 300 (invalid update tool) while trying to flash your device look at this thread!
NOTE: If you tried to flash a G3 rom with IPL/SPL in the rom on a G4 you probably will have a bricked device! DON'T flash the new 3.08 and 3.09 IPL/SPL to your G4!
NOTE2: If you got problems flashing with softSPL: Follow this great thread by mun_rus: Solutuion found: how to flash any rom to CIDLOCKED DEVICE. If your device won't start after flashing you can use step G4.2 and G4.3 and try again. Also look at this thread by eddieitman: Faria G4 Step by step installer with instructions to make sure you did all the necessary steps!
Crashed during flash
It has been suggested that I download Wizard Service Tool. OK, I did that. The Wizard Service Tool says to connect to ActiveSync. Can't do that. Phone is locked in Bootloader. It boots up into Bootloader. Any action requiring ActiveSync won't work as long as the phone is locked in Bootloader. Any suggestions as to procedures at this point. Remember, that trying to flash the ROM at this point, I get a message 300 that says I need to get a newer update utility.
Crashed during update
It has been suggested that I flash with wizar-love rom. Did that. Got a message 300, my phone need a newer update utility.
jphuffs said:
It has been suggested that I flash with wizar-love rom. Did that. Got a message 300, my phone need a newer update utility.
Click to expand...
Click to collapse
go to the G4 section and look for the HardSPL thread. Once there get the MUNRUU file from first post and use it with the ROM you wish to flash as it might do the trick of the ERROR 300
crashed during flash
It was suggested that I go to G4, first thread, HardSpl and down load file, munruu. Didn't find any such file. Went to second thread, by mun_rus, but was unable to download file.
My 8125 is locked in bootloader and I don' know what to do.
I still need help!!
jphuffs said:
It was suggested that I go to G4, first thread, HardSpl and down load file, munruu. Didn't find any such file. Went to second thread, by mun_rus, but was unable to download file.
My 8125 is locked in bootloader and I don' know what to do.
I still need help!!
Click to expand...
Click to collapse
this is the thread. and the link is there......
http://forum.xda-developers.com/showthread.php?t=332320
or another thread with link...
http://forum.xda-developers.com/showthread.php?t=334796
jphuffs said:
It was suggested that I go to G4, first thread, HardSpl and down load file, munruu. Didn't find any such file. Went to second thread, by mun_rus, but was unable to download file.
My 8125 is locked in bootloader and I don' know what to do.
I still need help!!
Click to expand...
Click to collapse
download latest Official Rom from carrier official site, establish usb connection while in bootloader flash,it will start working,after that follow the procedure of unlocking and upgrade
or if you have put in Sdcard,remove it and then switch on the device,it might get ok.It's seen in many cases that some Sdcards create problem while upgrade and bootloader screen gets stuck,by removing it,it starts to work fine
good luck
(mestrini;1565518]this is the thread. and the link is there......
http://forum.xda-developers.com/showthread.php?t=332320
or another thread with link...
http://forum.xda-developers.com/showthread.php?t=334796)
My phone is a G3. These links are pretty adamant about being for G4 only
jphuffs said:
My phone is a G3. These links are pretty adamant about being for G4 only
Click to expand...
Click to collapse
I'm talking about the, so called, 'MUN RUU' which are the files used to upload the nk.nbf. You just have to replace those for the ones you're using now; NOT THE nk.nbf, just the others...
zabardast_1 said:
download latest Official Rom from carrier official site, establish usb connection while in bootloader flash,it will start working,after that follow the procedure of unlocking and upgrade
or if you have put in Sdcard,remove it and then switch on the device,it might get ok.It's seen in many cases that some Sdcards create problem while upgrade and bootloader screen gets stuck,by removing it,it starts to work fine
good luck
Click to expand...
Click to collapse
What is "Official Rom from carrier official site"?
The SIM card was removed.
Hope this helps
jphuffs said:
What is "Official Rom from carrier official site"?
The SIM card was removed.
Click to expand...
Click to collapse
For instance, if you are (like me) with TmobileUS, go to the Tmo site and go to the page that gives you the download to rom 2.26. I have that rom, if you are with Tmo, but won't be able to upload it until later...
http://tmobile.infospace.com/tmweb/...wnloadCenter/DeviceDownloads.aspx?deviceID=24
THAT^^^ is for TMOUSA...it is the official Tmo rom. If you are with cingular/att, you need to access their website and download their official rom, etc.
DESPERATELY NEED HELP.
Every time i connect my wizard to my machine using the USB cable, i get the following message in baloon.
"One of the USB Devices attached to this computer has malfunctioned, and windows does not recognize it."
It appears as "Unknonw Device" on windows device manager.
This started happening when i changed my ROM to AMP.v2.Vanilla. Prior to that my wizard was connecting fine. I have been trying to resolve this for days now but no luck.
Following are the things i have tried.
1. Un-installed Activesync & re-installed.
2. Soft & Hard Reset the device.
3. Tried going in bootloader so that i can install my preivous rom, but the machine still doesnt recognize the device and gives the same message as mentioned above.
4. Removed all the USB controllers and re-installed in the machine.
5. Tried on different machines but same results, so its not machine specific.
6. Tried with a new cable to so its not the cable, it has to be the device.
Anyone who can help with this. I am sure i am not the only one having this trouble.
Any kind of help is appreciated. Just need to connect and go back to my preivous rom.
FYI: I am running WINXP SP2 on my machine.
ROM: 10.0.0.10
Radio: 02.69.11
Protocal: 1.1.13.30
Thanks in advance.
Nick.
You can flash in bootloaders mode,its not necessary to activesync.Get you phone in Bootloaders (tri color screen) by holding down Camers button and either Soft Reset or push Power On button,it'll go into bootloaders,hook up the phone with pc via usb cable,watch small usb appear at the bottom of the bootloaders,its good to go and run the RUU in the Rom,it'll start to flash and upgrade.Solve the activesync problem afterwards.
Thanks for the reply mate but i have already tried that.
I went into the booloader and connected the usb. It does show USB at the screen, however my PC doesnt recognize it and the RUU doesnt run. It says to connect the device.
I am not at all worried abt the activesync. Syncing is the last thing i'll think. I just want to connect and go back to my previous rom.
Any other suggestions.
Please see attached screen shots.
This sounds like a hardware issue on your phone. I doubt this works but go to start -> settings -> connections -> usb-pc and either check or uncheck the box then close that app.
If that doesn't work Search for the thread on flashing from the miniSD card. But again, this sounds like the usb on your phone has failed.
I have tried checking the USB to PC and unchecking it. No help with that.
One more interesting thing is the phone does get charged with the USB cable, just doesnt connect.
Will check the thread for flashing from minisd.
Thanks bunches.
hmm,
Hard reset your phone and uncheck the option 'allow network connections' or something in the phone settings...> connections...> usb to pc
This error occurs when there is an “open port error” before upgrading ,You can reset the device and run RUU again. If you still encounter an “OPEN PORT ERROR” again, reset your computer and try again. disable or stop any antivirus/firewall running or any other such program which might be hindering the flash,don't surf the net.
Kill 'WCESCOM' altogether,in the Task Manager,stopping activesync.
nick_shire said:
I have tried checking the USB to PC and unchecking it. No help with that.
One more interesting thing is the phone does get charged with the USB cable, just doesnt connect.
Will check the thread for flashing from minisd.
Thanks bunches.
Click to expand...
Click to collapse
hmmm,you got a connection problem buddy,the mini usb port of the phone is broken or damaged,you cannot flash with sdcard method,untill you already had made a backup of the rom earlier and saved it on the sdcard.
Get the mini usb port of the phone repaired or you can try to wriggle it a bit and check if it works and try to hold it there in that possition till the flash completes.
IS there a place i can get step by step process of flashing through SD card?
For all the forums, i am not able to understand anything./
Even the mtty doesnt work, it doesnt open the usb port.
No Luck as of now.....Am very desperately waiting for any Saviour....PLEASE
No other way out,except to get the freakin mini usb port repaired or replaced.
zabardast_1 said:
hmmm,you got a connection problem buddy,the mini usb port of the phone is broken or damaged,you cannot flash with sdcard method,untill you already had made a backup of the rom earlier and saved it on the sdcard.
Get the mini usb port of the phone repaired or you can try to wriggle it a bit and check if it works and try to hold it there in that possition till the flash completes.
Click to expand...
Click to collapse
Dang, thats right. I forgot that on the Wizard you can only flash a previously saved rom image. Can't just flash roms like you can on the Tilt.
Yep, basically, you have to get the USB port fixed as you are stuck where you are currently at on the Wizard I'm afraid.
Thanks guys. Have given my Wizard to get the Mini USB Port changed. I have my fingers crossed. Hope it works.
What exactly happens to the mini usb port?
I am having the same problem syncing.
The phone hooks up, charges, and makes the "connected" sound when I plug it into the usb port, but NO activesync...DOH!!!
Honestly, i couldn't figure it out.....no one seems to know whats the cause. The phone is bricked. It wont even start now... and its lying....
I am using an LG KS20 these days.....
Let me know if somebody happens to find a solution for that.
nick_shire said:
Honestly, i couldn't figure it out.....no one seems to know whats the cause. The phone is bricked. It wont even start now... and its lying....
I am using an LG KS20 these days.....
Let me know if somebody happens to find a solution for that.
Click to expand...
Click to collapse
Dear NIce_shire,
i am having the same problem and i got it resolved just by holding and tightly pressing the mini usb in my device. Its basically the problem with mini usb port of pda (Hardware) not a software one. Get it reparied from market or do it by urself. Good Luck!
USB link?
Hi mfrazzz
I have the same problem - USB link stopped working after a Radio upgrade. Definitively not a h/w USB miniport problem. Even when I get the Wizard G3 phone into bootloader and the USB word is at the bottom in the white line, flashing ROMs does not work as the RUU reports Error message stating no USB link (BTW, ActiveSync also reports no mobile device present and doesn't connect).
Is this a bricked phone then?
Thanks.
DesperateDan
PS The set is an MDA Vario and I had successfully installed S.V.I.s Manila 4.5 Beta (IPL 1.01, SPL 1.01 shows now, but was IPL 1.01, SPL 1.06 prior to installing Manila and Radio was 1.12.10 and I upgraded it to 2.69.11 and then the bloody thing stopped working and the USB link can't be enabled again)
Dear all,
I was facing the same issue of "USB device malfunctioned" and got it resolved yesterday. Its not because of software neither coz of cable (i did changed lots of cables but faced the same issue), its just because of mini USB in device. Its working perfectly alright now, it may not be replaced even dont need replacement at all. It needs minor soldering, even you can do it by urself. Just open 4 screws at its back (two under the camera cap one is below stylus placement and 4th is on opposite side) and open it. No need to be worried about......
Regards,
Barjees
Hi every one ! i have a HTC HD7 from T-mobile and i did the Mango beta update on it and i did not make a backup file, i have been trying to go back to the previous OS settings but all of the programs or ROM that i try running, can not see the phone connected to the computer. I get error 260, not one of ansar ROM can see my cell as been connected even though i check that it is and that active sync sees the phone as been plugged in and the drivers are installed. Can any one help me to do this down grade, please
you'll need to d/l a rom from ansthar, based on who your cell phone provider is.
Please, give some more info about your phone (OS version,Radio software version etc...).
You can find them on your phone (settings - about htc hd7 - more info).
Thanx
the phone is a T-mobile HTC HD7
OS 7661.WP7_5_Trial
(mojobld).20110607-1657 what is this?
Radio software version:5.51.09.11axxxxxxx09U
Firmwear revision number xxxxxxxxxxxx.531
you see i did use the windows phone support tool and i run the tool to its completion but the mango update did not install, than i downloaded a program called "provision" than i downloaded the zune 4.8 than the update started automatically and smoothly . i soon after deleted the window phone support tool thinking that i would not need it again, until i read that i need a back up to restore my phone if i wanted to install the mango update later. will i have downloaded just about every tool out there to restore my phone but when i run the tool it does not see the phone as been connected , i checked and i see the phone plug in my activesync so i was wondering that since mango is installed this programs do not see it since they where made for nodo. your help will be greatly appretiated , thanks in advance
Are you using the new Zune for Mango? cause the old zune won't recognise your phone
try this link Here
See if you can go back with zune... ALWays BAck Up!!
Ok. To what tfn wrote I say YES you should always make a backup and you can do it as it's explained on the link he provided.
For Your phone, since you dont have backup go to http://forum.xda-developers.com/showthread.php?t=876451 and find RUU_Schubert_TMOUS_1.20.531.01_Radio_5.51.09.11a_2 2.31.50.09U_by_ansar.
Download it - this is original ROM for flashing your phone - it will take you back to 7004 version. Follow the instructions in ansars post.
This one worked for me.
http://forum.xda-developers.com/showthread.php?t=1101344 - here you can follow instructions for updating to NoDo and Mango.
Now some important thing...
1. When you are taking beckup you have to have Zune 4.7 installed (not 4.8)
2. You can also see my thread (it could be helpfull) - http://forum.xda-developers.com/showthread.php?t=1179095
I hope you will make it!
i will give this a try and thanks for the help
i guess i'm **** out of luck, i did everything as written on the post and I did manage to get the ChevronWP7. ChevronWP7 does not see the phone as been connected , i try the steps with zune4.7 and 4.8 and i get the same message the chevronwp7 can not connect to the phone, also when i run the Application Deployment throws an error stating that the phone is developer locked and i need to contact Microsoft for steps on how to unlock it .
I need some help..can someone with a T-Mobile US phone please list all regedit keys for the HD7. After screwing around with the regedit settings to enable the HD7 read as a storage device, this happened and is the cause for Zune or any other program to not read the phone.. thanks in advance. i need all regedit keys with values and exact name.
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\U SB\VID_045E&PID_04EC&MI_00\6&27ffd631&0&0000\Device Parameters\WUDF
DiMatador said:
i guess i'm **** out of luck, i did everything as written on the post and I did manage to get the ChevronWP7. ChevronWP7 does not see the phone as been connected , i try the steps with zune4.7 and 4.8 and i get the same message the chevronwp7 can not connect to the phone, also when i run the Application Deployment throws an error stating that the phone is developer locked and i need to contact Microsoft for steps on how to unlock it .
Click to expand...
Click to collapse
Did you get your phone to 7004 version with flashing?
If yes then:
1. send to your e-mail (which you have configured on your phone) chevron.cer in attachment
2. open that mail on your phone and tap on attacment
3. install cetificate
4. in settings on the phone turn on FLIGHT MODE
5. connect the phone to a computer and start Zune
6. run Chevronwp7.exe as administrator
7. check those 2 boxes and press unlock
DONE.
I just did it on mine hd7 (just to be sure).
No i could not do a thing, no one of the steps that you have recommended have work, all i get is an error message from every single software that the device is not connected so i cant do a thing . is like my phone is not connected and i get error. i get the same error weather i have zune 4.7 installed or 4.8 . i also get a message from Application Deployment : the device is pin locked or the device is developer locked , contact microsoft on how to unlock the device or go to a web address . I mite be missing some drivers or something
To downgrade, you need to boot into the bootloader first.
1) Power off the phone (while disconnected from USB)
2) Hold volume up and press the power button
3) Continue to hold volume up until you see the RGB screen
At this point it will say something like "Serial Mode"
4) Plug in USB
5) Wait until it says something like "USB Mode" (you may need to install drivers on your PC, they're available via windows update, so you don't need to go searching for them)
At this point, you can run ROMUpdateUtility.exe, and it should succeed.
EDIT:
You only need to do this if downgrading via the RUU. To restore a backup via Zune, this is unnecessary.
The only program that seems to see the hd7 connected to the computer is zune4.8 if I install 4.7 it just does not see the phone connected. I got a windows XP tower hat I'm thinking to try all this steps and see if I can do it, actually do all the software I downloaded would work in windows XP?
Try the steps that I mentioned. If Zune opens, close it.
I had the exact same issue that you are, and this is how I was able to revert to a earlier version.
unsined said:
To downgrade, you need to boot into the bootloader first.
1) Power off the phone (while disconnected from USB)
2) Hold volume up and press the power button
3) Continue to hold volume up until you see the RGB screen
At this point it will say something like "Serial Mode"
4) Plug in USB
5) Wait until it says something like "USB Mode" (you may need to install drivers on your PC, they're available via windows update, so you don't need to go searching for them)
At this point, you can run ROMUpdateUtility.exe, and it should succeed.
EDIT:
You only need to do this if downgrading via the RUU. To restore a backup via Zune, this is unnecessary.
Click to expand...
Click to collapse
This guy nailed it. Hope it works out for you man.
re install your opp system that's what i did and it worked zune does somethin to chev so just re install and u should be good
I just want to post that finally I got my HTC HD7 Flushed to the its original ROM and i have been trying other ROM's as well and the phone is performing just fine, except of the fact that i'm connected to Rogers and i cant find a ROM that would enable the right antenna settings so i can connect 3g . if any body know witch ROM to use please let me know . Thanks every one that spent time helping me out .