Going back to original Rom - P3600 Software Upgrading

Hi,
it's my first post and I need help from the forum.
I own a Trinity for about 2 months. Since I upgrade the Rom (original from site HTC Europe) for the Gps Enabled I started with the problem related in this post
http://forum.xda-developers.com/showthread.php?t=295043
The screen after a few minutes of use starts blinking and anywhere I use the stylus he does "Start". After some more minutes the screen freezes and I can only use the buttons. I installed TaskManager and the CPU is always at 42%-43% when it haves this problem.
My girlfriend owns another Trinity with the original Rom. (with GPS Disabled)
My question is:
Can you help me and tell me what I must do to extract the original Rom from her Trinity in order to use it on mine?
Note: I upgrade it last night to the new Rom from LVSW and the problem happens again.
Thanks in advance.
Nice forum... top of the art.

read wiki, how to dump & how to reconstruct.

nunod said:
Can you help me and tell me what I must do to extract the original Rom from her Trinity in order to use it on mine?
Note: I upgrade it last night to the new Rom from LVSW and the problem happens again.
Thanks in advance.
Nice forum... top of the art.
Click to expand...
Click to collapse
Since you said that you have an HTC euro Trinity, you should be able to find an original rom here http://wiki.xda-developers.com/index.php?pagename=Trinity_Upgrades. However, I'm not sure changing the rom will fix it, check in the wiki for known problems, you could have a hardware issue.

Related

Going back to an older ROM

Okay I am a newbie and I installed the Mr Clean rom which is fine but how would I install the previous rom I had witch was the one from the HTC website? Basically all I am tring to do is change my splash screen and I have no idea how but I want the old rom but it doesn't seem to want to let me roll it back.
OK newbie, try searching the forum for your solutions first - you will be surprised what you might find. :wink: This took me less than a minute to locate.
http://forum.xda-developers.com/viewtopic.php?t=52768
Basicly Faria has put together a bunch of different splash screens which will install in exactly the same fashion as a new ROM would. As it only loads a new slpash screen you will not lose any data. You will also be able to keep the Mr. Clean ROM but have a different splash screen. There are at least 2 HTC splashes listed and the one that I had a quick look at has a preview so you can see which one you prefare before you do the install.
Enjoy...
But is it possible to go back to an older/different rom once you install Mr Clean rom? I currently have a K-jam running the lattest rom, and was thinking about trying Mr Clean rom just to see how it behaves. The only think stopping me is what if I don't like it! Would it be possible to revert back to my current rom?
Can't see any reason why it shouldn't work. As far as I know none of the home cooked ROMs available on the forum have a function that does a compare between the existing and intended ROM versions and prevents any downgrading.
As to whether you will like the newer version, it is hard to see why you wouldn't. Mr Clean's version is spot on if you want the latest OS, the best Radio ROM and a very light extended ROM and with you changing your splash screen to one you like you should be sorted. All you need is to install whatever cab files you need for performance tweaks or network settings.
jt_armstrong said:
Can't see any reason why it shouldn't work. As far as I know none of the home cooked ROMs available on the forum have a function that does a compare between the existing and intended ROM versions and prevents any downgrading.
As to whether you will like the newer version, it is hard to see why you wouldn't. Mr Clean's version is spot on if you want the latest OS, the best Radio ROM and a very light extended ROM and with you changing your splash screen to one you like you should be sorted. All you need is to install whatever cab files you need for performance tweaks or network settings.
Click to expand...
Click to collapse
Well it doesn't! :S Once you use Mr Clean rom you can not go back to the official Kjam rom! My only problem with the Mr Clean rom is that there is somewhat increased consumption compared to the rom I had before! Oh well! I guess I'll just have to get used to it!
petrosk73 said:
jt_armstrong said:
Can't see any reason why it shouldn't work. As far as I know none of the home cooked ROMs available on the forum have a function that does a compare between the existing and intended ROM versions and prevents any downgrading.
As to whether you will like the newer version, it is hard to see why you wouldn't. Mr Clean's version is spot on if you want the latest OS, the best Radio ROM and a very light extended ROM and with you changing your splash screen to one you like you should be sorted. All you need is to install whatever cab files you need for performance tweaks or network settings.
Click to expand...
Click to collapse
Well it doesn't! :S Once you use Mr Clean rom you can not go back to the official Kjam rom! My only problem with the Mr Clean rom is that there is somewhat increased consumption compared to the rom I had before! Oh well! I guess I'll just have to get used to it!
Click to expand...
Click to collapse
Why can't you go back? I've run every ROM sumitter has released. Over the weekend I installed the Mr. Clean ROM . Put on the PDA Mobiz version yesterday. I just went back to the original Cingular 1.08 successfully this morning to double-check this response. IPL, SPL, GSM and OS reflecting changes each time. Now I'm going "back" to sumitter's test2. If you unlocked you SID/sim initially you shouldn't have any problems regarding this. faria documented the procedure back in April.
(yes I love flashing my phone)
I can't believe that the Kjam is that different.....
Steven
chow
Well I must have done something wrong then as my SPL is stack at 2.24! I can use the downgrade rom but then can not upgrage to anything but mr clean!
Well I must have done something wrong then as my SPL is stack at 2.24! I can use the downgrade rom but then can not upgrage to anything but mr clean!
First you need to download and install Button's 1.05 at ftp://xda:[email protected]__RUU_Wizard_1050412_WWE_101_11210_WWE.exe . Make sure to allow the extended ROM's to execute. All problems solved as Pinhead said.
Original thread is at http://forum.xda-developers.com/vie...&start=0&sid=07fe38f7fd43a39238c55d01410a0940
Good luck!
Steven
chow

Some questions

Hi!
After installing the HTC Toupad on my Kaiser, I have experienced big problems. Letters on the Keyboard (QWASYX) didn't work and even the onscreen keyboard didn't recognized these letters. So I decided to uninstall the application. But now I have other problems with my Kaiser and so I decided to Hardreset my device. But before I do this, I want to upgrade my Kaiser to WM6.1 and update it to the newest ROM/Radio.
Now I have some questions relating to that.
As a result that I am a Super Moderator in another forum I know that it is bugging if people don't read the Wiki/FAQs. I have read them, but I don't understand many things :-|
I have handled it to unlock my device, but when I was reading about updating to WM6.1, I saw only things like: "... works only with 6.1", update this, update that, and I don't know in which order.
First of all: Could anyone explain me how to update my Kaiser to WM6.1 and the newest Radio?
Secondly: What is this Duty FW? Is it a modified Rom with added apps?
Finally: I have a normal Kaiser. Not a Vario III, AT&T or something like that. Just the austrian version of the Kaiser with no brandings and so it would be good to have a Firmware without any brandings.
Thx in advance.
BTW:
ROM version: 1.56.405.5
Radio version: 1.27.12.11
Oh, I have forgotten one thing: Is it possible to change the LED blinking in the Phone Mode? To change it from green to blue?
The letter problem you were having was a simple fix with a cab that can be found all across this forum. All the ROM's can be found in the ROM Development forum and as far as what has been changed, modified, added, programs list, can all be found in the FIRST or SECOND post of each of the ROM's. So you will just have to read through them and find one that suits you best as they all have something different. Most of the radio's that can only be used on 6.1 ROM's will say "Will only work on 6.1 ROM's". And I would like to add even though you don't have at&t DON'T FLASH THE 1.65.17.10 RADIO.
KDKobes said:
The letter problem you were having was a simple fix with a cab that can be found all across this forum. All the ROM's can be found in the ROM Development forum and as far as what has been changed, modified, added, programs list, can all be found in the FIRST or SECOND post of each of the ROM's. So you will just have to read through them and find one that suits you best as they all have something different. Most of the radio's that can only be used on 6.1 ROM's will say "Will only work on 6.1 ROM's". And I would like to add even though you don't have at&t DON'T FLASH THE 1.65.17.10 RADIO.
Click to expand...
Click to collapse
Ok, thx first of all. Dutys rom sounds nice. What do I have to do first? It is still a little mystery for me ^^
alcbottle said:
Ok, thx first of all. Dutys rom sounds nice. What do I have to do first? It is still a little mystery for me ^^
Click to expand...
Click to collapse
You need to make sure before you flash a rom on to your kaiser that you flash hardspl - http://forum.xda-developers.com/showthread.php?t=334679, and than after successfully installing that you can flash the rom of your choice. Please read the first sticky thread under the kiaser rom development form - http://forum.xda-developers.com/showthread.php?t=369282; it has all the info you need pretaining to everything involved when it comes to flashing your kaiser. I strongly recommend you go through it and read the posts it points to that are relevant to flashing.
Once you have done that it is pretty simple process; just do yourself the huge favor and don't flash until you have flashed hardspl or you will brick your phone.
If its still a mystery I would start here http://wiki.xda-developers.com/index.php?pagename=HTC_Kaiser#ROMx20.Upgrading
No pun intended.
@thesire
I have already installed HardSPL. Otherwise I couldn't have unlocked my device with this method: http://forum.xda-developers.com/showthread.php?t=361039
I have used just the Sim Unlocker Method. Not the Kaiser SIM/CID Unlocker & Changer
That's the reason, why my mobile phone is now with an english language
Just one important question: Do I have to change my current radio for the new Duty Release?
@KDKobes
Why shouldn't I flash THE 1.65.17.10 RADIO?
Some ROM's come with radio's some don't. Most of Dutty's ROM's come with radio's, but if you want to keep your radio then I would suggest finding a ROM without a radio in it or making sure yours is compatible with the WM 6.1 and reflash it back. The 1.65.17.10 radio will lock your phone to that radio only and you will not be able to change it until somebody can fix it. Alot of people are stuck with that radio now and can't change.

Blackberry Connect - bbconnect - on Touch Diamond

Hi All.
So here we go again - trying to get Blackberry Connect to work on a new device..... so we've succeeded on the Kaiser and Touch Dual with both original and cooked rom's but I can't get any version to work on the new Diamond - received mine yesterday after frying the mini usb port on my Touch Dual and its one of the 1st things I installed? I've tried all the current fixes (I think) most of them summarized here in Elec.Two's post:
http://forum.xda-developers.com/showthread.php?t=371652
I'm hoping there will be a few others out there working on the same problem - I've just changed my aku back to .1.1.4 - I can get the device to sync when connected using activesync as a pass-through connection but get the "old" data tunnel available message and then it flips to "not connected" .....
I'll keep trying and keep this thread updated but could really use some help!
Hi, Im trying to change the name of this. I would like to change it to HTC-Herm200 or someting else. But I dont know what the build number have to be there. Anyone know ?
this has NOTHING to do with rom development... use some sense people! moving thread!
ROM Development????
Not sure what usap 's post is all about but my question is very much about ROM development? I'm looking for a registry change that will fix the problem that the CURRENT STOCK ROM has that means that bbconnect will not work?
I currently have WWE_1.34.831.1_52.24.25.08_0.93.25 loaded and have tried the standard "Tweaks" from past "ROM Development" but none have worked so far? I'm on constant watch for another ROM release (Cooked or Stock) or a Registry fix to help solve the problem?
ShogunMark - do you really think the thread was in the wrong place???? If its not ROM development then I'm in need of some guidance?
Im tying to change in HEX Editor the Signatures. For example there are DIAM100 (or DIAM10000) and build 19588. I changed it to HERM200 and 19588->17745. I can change it without changing the size of .nbh. But thre are "Diamont" Signatures too and by changing Diamong->Hermes wir have one less character (7->6). It changed the size of the .nbh.
So im trying to flash it to the Diamond nad about 96% OK, but then ROM flash error.
A meaning of it all is that it have to work, because RIM asks the Number and NAME and then when its in the list->OK, NO->pending.
I need some tools like SSPL 1.34 and ROMUpdate Utility that dont asks of CRC or something else.
Please Help
I've seen a few members reporting that they have a later ROM version > 1.35.707.3 - See thread http://forum.xda-developers.com/showthread.php?t=394985&page=12 I have not been able to find this as an officially released ROM and I'm not aware that its been dumped as yet? This slightly newer ROM may help solve the problems and may help usap with his question on the version number?
If there's anyone out there who know's the AKU and the version number for ROM 1.35.707.3 can you let us know???
Thanks
Blob8me said:
Not sure what usap 's post is all about but my question is very much about ROM development? I'm looking for a registry change that will fix the problem that the CURRENT STOCK ROM has that means that bbconnect will not work?
I currently have WWE_1.34.831.1_52.24.25.08_0.93.25 loaded and have tried the standard "Tweaks" from past "ROM Development" but none have worked so far? I'm on constant watch for another ROM release (Cooked or Stock) or a Registry fix to help solve the problem?
ShogunMark - do you really think the thread was in the wrong place???? If its not ROM development then I'm in need of some guidance?
Click to expand...
Click to collapse
he moved the thread as it WAS in the wrong place, blackberry connect isnt related to Diamond ROM Development.
Yes you have to Hex edit the ROM to get it to work, but it doesnt belong in that forum, and to your other question the newer build of ROM is not a newer AKU or build.
walshieau said:
he moved the thread as it WAS in the wrong place, blackberry connect isnt related to Diamond ROM Development.
Yes you have to Hex edit the ROM to get it to work, but it doesnt belong in that forum, and to your other question the newer build of ROM is not a newer AKU or build.
Click to expand...
Click to collapse
I disagree - for most every other device - getting bbconnect to work has been the result of ROM Development - if your familiar with the other device forums - you'll see that Blackberry discussion is often linked with and found in the ROM development forum?
HOWEVER - I dont really care which thread it sits in as long as "we" can work on a solution if there is one available?
FINALLY - Thank you for the information on the Malaysian ROM
Blob8me said:
I disagree - for most every other device - getting bbconnect to work has been the result of ROM Development - if your familiar with the other device forums - you'll see that Blackberry discussion is often linked with and found in the ROM development forum?
HOWEVER - I dont really care which thread it sits in as long as "we" can work on a solution if there is one available?
FINALLY - Thank you for the information on the Malaysian ROM
Click to expand...
Click to collapse
yes the ROM needs to be HEX edited but it has nothing really to do with the "development" of a ROM .
so when we get HardSPL ready and installed i will show everyone how to hex edit the ROM NBH files and then reflash it so bb connect can be used.
Blob8me said:
Not sure what usap 's post is all about but my question is very much about ROM development? I'm looking for a registry change that will fix the problem that the CURRENT STOCK ROM has that means that bbconnect will not work?
Click to expand...
Click to collapse
I'm not sure who to agree with...it really shouldn't matter so much to people.
Dark Fire said:
I'm not sure who to agree with...it really shouldn't matter so much to people.
Click to expand...
Click to collapse
Agreed - It shouldn't matter and here it will stay
I'm hoping for a tweak to the stock ROM (or even a "fixed" stock ROM to be released as I've heard that a next build Rom is due soon - and this has neen the main reason behind the delay in the UK and EU formal release??? Apparently - despite the popularity of "our" site less than 5% of device owners actually change anything on their phone never mind update firmware - official or otherwise? HTC are trying to minimise "support" issues by ironing out as many bugs before the next release - I know for a FACT that they use this site as a major test ground for any new device - so maybe the expansys release was intended after all???)
Thanks again.....
Blob8me said:
I'm hoping for a tweak to the stock ROM (or even a "fixed" stock ROM to be released as I've heard that a next build Rom is due soon - and this has neen the main reason behind the delay in the UK and EU formal release??? ... I know for a FACT that they use this site as a major test ground for any new device - so maybe the expansys release was intended after all???)
Click to expand...
Click to collapse
Yep, all of the evidence suggests that that's the reason behind the delayed release in Europe. New ROM. Hopefully with none of the bugs we've found so far (but I doubt it).
And that's a really interesting fact. It would be both nice and worrying to know that we influence them. (Nice when good devices like the Touch Diamond are announced, but worrying when there are major problems, such as that big driver problem).
Offtop (maybe)
I was playing yesterday with another phone and became the ROM extracted. So Registry and some of the files have the name of it in it. And I changed it to another name (Herm200 and HTC-HERMES) so that after the recreating and flashing the ROM it was everywhere Hermes. But PHONE ROM was dead (No signal, no phone). There were some imei*.pfg and some *.rgu and *.dsm where I changed all to HTC-HERMES and HERM200. So I had to flashing it to normal ROM.
And by the Diamond i worked with not extracted ROM. So i think there are 2 roads to change it: in extracted and not extracted ROM.
What do you think about it?
UPDATE on 1.34.831.1 and bbconnect?
Have just tried all the usual routes with the new EU Rom (details below) having used OliNex's SPL to Flash:
ROM: 1.34.831.1 WWE
Date: 5/25/08
WM6.1 CE OS 5.2.19588 (Build 19588.1.1.4)
Radio: 0.93.25.NS16
Protocol version: 52.24.25.08H
Still no success..... I've seen that there are other Roms also out there such as 1.35.871.5 but not yet available?
I was hoping that the Stock EU Rom would be OK as in the past the Stock "Official" Roms have run bbconnect with no changes and no problems???
If anyone has any other suggestions then your help would be greatly appreciated?
UPDATE ON Elite 1.0 and bbconnect....
Still nothings working - Sigh.....
I've got a specific request in the main Elite 1.0 Rom thread for walshieau to add bbconnect support now that HSPL is released - so hoping it wont be too long now!
walshieau said:
yes the ROM needs to be HEX edited but it has nothing really to do with the "development" of a ROM .
so when we get HardSPL ready and installed i will show everyone how to hex edit the ROM NBH files and then reflash it so bb connect can be used.
Click to expand...
Click to collapse
walshieau - any news on working on a solution now that we have HSPL out???? Can you add bbconnect compatability to the next Elite release????
UPDATE on 1.37.405 and bbconnect
Just added a comment on the main thread for this, the latest WWE EU Rom Release...... still not playing....
USAP - Any more thoughts??
walshieau - come on - you promised to help with a solution.....??? Help me out here????
Refresh......
Just refreshing as I'm getting desperate for a solution as I use the blackberry function for work and really don't want to switch back to my touch dual - has ANYONE had any success on the diamond with bbconnect?
Another "post" refresh.....
I'm still struggling to find a solution for this....???? In fact, I'm starting to wonder if there is a solution at all? Has anyone had any success at all with installing blackberry connect on any of the diamond Roms?
Blob8me said:
I'm still struggling to find a solution for this....???? In fact, I'm starting to wonder if there is a solution at all? Has anyone had any success at all with installing blackberry connect on any of the diamond Roms?
Click to expand...
Click to collapse
me waiting for a solution also. from what i notice, we just need 1 carrier to support bb on the diamond n we r all set. currently this is what i hav experience with the touch n touch dual which i have been able to connect despite local carrier not supporting it.
give a shout out if u do come across a solution though.

Dumping standard shipped ROM

Is there anyone who has succesfully dumped the Official Shipped ROM that comes with the European models ?
I'm sure that apart from me, there are other members who would like to revert to the offical ROM just in case something happens with the device. (need to send it back for a reparation)
I'm going to flash just right now anyway, as I'm positive that there will be someone in the future dumping the offical ROM.
\cheers, now pressing start
EDIT : After flashing I keep the high pitched noise that almost everyone is Reporting. I can't get rid of it. Be aware with this ROM,. you might get stuck with a hissing device that won't stop I'll wait for some solution and then flash again, can't use Winmo anymore
me too...please help us - i cannot use my device due to constant noising...
up0grading the EC chip drivers
I saw some remarks about the EC Chip driver update from HTC - will try that now, see if it helps anything at all.. For now, the device always hisses like a snake when Vista is active.
Without Vista active, it's mostly quiet, but gives no sound in WinMo, however, if you try to make a sound in WinMo, sometimes, after a few seconds, it will hiss and pitch for the duration of the sample played...
This is really annoying
hi,
i did a backup pof's way, so i have now part00.raw - part04.raw and SPL.nbh.
Rebuild Part02.raw and uploaded again. Working like a charm. Problem is: my original ROM is in German. anyone interested?
german but quiet is much better than english with noise.
please provide links.
Thanks
GERMAN..?
That sounds wonderful: need the the german ROM very urgent, can`t work with my beloved shifty...
Please share the ROM, thanks so much!
Me too!
I installed the GPS Bios pack - Easy BUT:
The noise only appears while staring after reinstalling the battery - just restart SnapVue after Vista is up and the noise is gone.
Also gone is the German keyboard under SnapVue - Regional settings don't change that!
GPS work in SnapVue and Vista (using ActiveSync & GPSgate - after test period ~30€).
Overnight SnapVue need app. double the energy than before!!!
Using GPS in Vista means NO internet/mail!
Wrong keyboard layout and battery drain tempt me to reinstall an original German ROM and to continue using my dear old eTrex with USB together with my Vista progs.
So, how and where2 can I find the German ROM?
Thanks,
Axel
Send the Rom-Link to a victim already. Waiting for an OK before i publish.
Victim report Nr. 1:
@tece: Thanks a lot, man, good job, it works fine..!
Regards and thanks a lot.
Alex
great!!
i noticed that pocketie is already installed and that \Windows\StartUp\PKG.exe and BlockTitleBar.exe are already removed.(like i did as described in this: http://forum.xda-developers.com/showthread.php?t=377441 thread before backing up the original ROM). Now I'm looking to get the registry preconfigured to not start Snapvue. Liberated German ROM will get released this weekend. If you can't stand waiting for that ROM send me or traumrakel a PM for the rapidshare link.
If you could include the liberation into the new ROM I would prise your name... ;-)
and here it is: http://forum.xda-developers.com/showthread.php?t=417901
I have rom dumps of:
- 1.30 WWE
- and whatever rom the CDMA shifts have.
does anyone need either?
cmonex said:
I have rom dumps of:
- 1.30 WWE
- and whatever rom the CDMA shifts have.
does anyone need either?
Click to expand...
Click to collapse
hello cmonex,
i m running the german rom as i do not have my original french dump, i would be very happy to install 1.30 WWE!!
even if tece rom is great in order to learn some german word
cmonex said:
I have rom dumps of:
- 1.30 WWE
- and whatever rom the CDMA shifts have.
does anyone need either?
Click to expand...
Click to collapse
Do you have the reconstructed ROM of version (original UK Shift): 1.30.405.0 WWE ? Can u post it/send it? Then I don't have to rebuild it myself, because I'm not that experienced it rebuilding myself. Also in case my rebuilded rom fails to work.
Many thanks!
cmonex
Could you please share the 1.30WWE
Thanks
Ram
You have it, it's the one having gps and sound bugs with european radios.
I'm using 1.22 because it's a stable base. Later version doesn't give you much, as graphic drivers are disabled anyway.
thaihugo
Cool. I followed pof's suggested way of dumping the original rom. Now I got all the raw files with correct start addresses. I am wondering whether I did correctly or not for SPL.NB. because the file size is 256 KB since I passed the same length 262114 as read in pof's post. When I used KaiserKitchen to reconstruct, I don't have baseRom and if I ignore that, I am not gettting the NBF file. I want to backup my CHT ROM and install your's (1.22 with GPS and sound). Could you please shed some light?
Thanks
Ram
Hi Cmonex ;
I need the non-touched 1.30 WWE rom for shift ; can you share please ?
Safak
Thaihugo , Saiweb
Do you have 130 WWE non-touched original rom ? I ve downloaded one from the forum but it is the "telenav"ed orig one , which i can not use at all...
Can you share if you have ?

Some questions

hi guys out there
i'm new to this forum and I like it a lot,
some many files and informations that are useful...
I already have touchflo 3d on my xperia, but now I'd like to flash a new rom.
Now my questions
1) when I do hard spl, do i have to connect the phone in tri.color screen or normal
2) how do i exit the tri color screen, did that by doing soft reset, any other possibility ??
3) Which 6.5 sense rom ??? I'm german so i'd liked to have a fast and stable rom which should be in german . I only would use a english rom if the difference is big
4)Equal which radio I have or do I have to upgrade it too
5) can i use all the programmes i downloaded so far for my xperia with stock rom??
cheers
MR. D - S
1. follow instructions provided with hard spl program.
2. soft reset the phone or take out the battery.
3. depends on what you want in the rom, every rom has its pros and cons you need to experiment to find the one you like. Not everyone does german language rom, there is no real difference except language and what is included. Most roms are very similiar as chefs use standard packages with their own tweaks.
4. you should keep the radio that comes with the stock rom if it works in your part of the country without problems.
5. yes, you can use all the programs you have downloaded, depending on the rom you may have to download a framework program to get the best usage out of your program.
cool , thank you !
I'm now between x826 rom and xkans rom
could someone compare them and tell me whether xkans rom is as fast as x826 rom (i read that its one of the fastest and bugless roms)
anothher question by me
i want to get rid of the qwerty keyboard, I just downloaded PM reg editor but I cant find hklm/harware... to set CurrLan to german
could someone post a link to an regeditor which is easy
again a question can I use the xperia tweak v2 on 826x rm .?
EDIT
can anyone tell me how i can enable sim contacts to be in my contact list, xperia tweak doesnt work on 826x
THX
now i need urgtent help,
i dont now what to do,
my phone is stuck into flashing , the bar is nearly at the end but now its showing update in progress since half an hour,
my first flash ysterday only took 5 min.
plz help !!
Mr.D - S said:
now i need urgtent help,
i dont now what to do,
my phone is stuck into flashing , the bar is nearly at the end but now its showing update in progress since half an hour,
my first flash ysterday only took 5 min.
plz help !!
Click to expand...
Click to collapse
It's difficult to help as you didn't mention current and new ROM versions...
Maybe a task29 will help (search the forum for the corresponding thread).
I finally got it working agaun over usb, so I'm happy again.
But thx for trying to help me...

Categories

Resources