Related
Hello,
I have this rom : RUU_Trinity_LVSW_WWE_1.25.0.8_GPS (AKU 3.5.2)
from http://forum.xda-developers.com/showthread.php?t=302198
I wanted to test the new WM6 roms, unfortunately, my trin doesn't update with any rom I tried (Orange, HTC, LVSW Wm6, Mun_Rus Wm6, ...)
It tells me : "ERROR 262 : UPDATE ERROR
... communication error during the process"
I'm stuck on LVSW Wm5 rom :'(
Not sure if Des SPPL is causing this problem... anyway, I tried to update it from Bootloader or synched, on XP and Vista, 5 differents roms... no luck.
I would really appreciate some help, thanks
can you list the steps of what happened, in order?
also, just to make sure i understand, have you already tried to manually enter the bootloader and THEN run the RUU? *edit* one last question, have you tried this.. after the error, leave your device connected and in bootloader, then restart the RUU.. can you give me your device details too?
Well, when I run the update with normal step (connect AS, then launch update...) when the update is ready to be started (progress bar appears), phone have to switch to bootloader, which it does. However, it seems that the RUU is waiting for that since it return me this error:
ERROR 246 : Device not responding
And I have to exit. I don't understand ?
Progress bar didn't even appear on the phone.
At this time boot loader shows
IPL-SSPL by Des
SPL-1.07.ds
So since I'm already in Bootloader mode, i try to launch RUU again. Here is the error I get when the progress bar appears on both phone and PC :
ERROR 262 : Update Error
And it offer me to recover the device, which I don't need as the current rom has been left untouched and is still functionning after the error.
Then I reset the device to enter bootloader this time:
IPL-0.50
SPL-1.06.0000
same error : ERROR 262 : Update Error
I'm kinda out of option, thanks a lot for your help !
well, it's been a pretty common thing for the RUU to give an error when the device goes in to bootloader (can't detect it for some reason). Most times, simply running the RUU again while the device is still in bootloader works fine.
Why don't you put hard-spl on just in case, manually enter bootloader (which will then be hard-spl) and run the RUU again. You shouldn't enter the bootloader manually unless you've loaded hard-spl or sspl on to your device. From what i understand you won't be successful from what you did after the hard reset. When your phone went in to bootloader the first time, it was with SSPL pushed to your device by the updater program to enable you to update safely. After resetting, you're back to your normal bootloader which won't help anything.
I know one time it did this to me, and wouldn't connect to my device. I started the RUU about 3 times in a row with my device on bootloader, and for some reason after the 3rd time it suddenly worked.. weird, i know.
anyway, hard-spl will make the whole process safer.. let me know if it connects or not, i'll see if i can help you troubleshoot
I wanted to install hard-spl, but it runs as a normal RUU and give me exactly the same errors as a normal run update (error stated above).
So I don't see how I could install it
Another thing weird, when I run a official HTC rom update, when the udpdate should start (device enter in boot loader, progress bar appear in bot PC an device), the Trin reset itself and boot as normal... of course the RUU gives an error due to this reboot ...
Same weird behavior with an official Orange rom...
Now I'll try with SSPL...
Oh and thanks a lot for your help
simply try to run twice ROMUpdateUtility.exe after error
Please read carefully what I have posted (and the steps I ran into)...
Already launched again RUU, it gives me an Update Error and the device is stuck on the screen that show the progress bar.
Need to soft reset... I can't launch again the RUU after that since the device is no longer recognised as connected on PC.
I confirm I can't manage to install the Hard SPL, even after laoding Des sspl from the device...
Defintly blocked
At last I have succeeded in upgrading the device. Seems like my bootloader was somehow corrupted or something... after doing another Hard Reset it have installed hard spl succesfully...
I had already done a hard reset before, so I don't understand what happened.
Nevermind, at last i can try wm6
thanks a lot for your help racerx_ anyway
hey no problem.. not sure that i actually helped haha.. but i'm glad you sorted it out. happy flashing!
Might it have been the USB driver on the desktopside ?
Did you see XP recognize and install HTC USB device again, after device disconnecting from AS and going into bootloadermode for first time ?...
Just a thought...
Not sure what it is, but it's happening again, can't update anything as the bootloader seems somehow corrupted.
When i enter bootloader it briefly display the 3 color, then grey screen with "loading" and then the hard spl screen from Olimpo... the only problem I see is that it does no longer display TRIN100, but only little dots (like if it was corrupted)...
Very annoying situation, and I have already done some hard reset, but nothing
So more exactly, where I start DES SSPL or when I enter Olipro Hard SPL (that I installed before WM6), it shows the good infos like :
TRIN100
xxxx
TRIN100
SPL-
But after 1/4 of second, it start loading for a very short moment
and display again the RGB screen with the infos except the "TRIN100" parts are like this ':':':':':':
Anyone has seen this before ???
@cedrick: You have a SD card inserted on this device, right? if so, remove the SD card and try again.
If the SD card is not the problem, then you might have overwriten the memory region where the ModelID is stored. I can help you to recover it if that is the case.
pof said:
@cedrick: You have a SD card inserted on this device, right? if so, remove the SD card and try again.
If the SD card is not the problem, then you might have overwriten the memory region where the ModelID is stored. I can help you to recover it if that is the case.
Click to expand...
Click to collapse
...... well well, that was simple hahaha (and I feel stupid lol).
yes I had my SD inserted (and I remember only now that the last time it worked I had indeed removed the mini-SD).
So, thanks to you I have understood this issue at last !
Muchisimas gracias por tu gran ayuda pof
Now the question is, wtf do u have on this SD card? LOL
Errr that's a good question... maybe it is time to clean those 4go of things (which most of those come from the SD I had on my Prophet, in the top of that)
Anyway, it's a rare specimen indeed... want a copy to play with heh ?
At 56%, the desktop went to a blue screen and said an error had occurred and the system must be restarted. The screen asked if I had installed any new programs, check with the adminstrator, etc. The only program recently installed is the program for this ROM revision. When it crashed, the phone had a completion bar in the top 1/3rd, showing 56% completion. The rest of the screen was white. I restarted the desktop and was unable to establish a sync connection. I then preformed a hard reset on the phone. When it restarted, it showed 4 color bars, red on top, green, blue and white at the bottom. Since I cannot restablish a sync connection, how do I finish the modification. I am now concerned that I have "bricked" the phone. I am reluctant to try this mod on another phone until I can determine what went wrong.
Adding additional info
My phone is a G3, CID and SIM are unlocked, desktop is using Windows XP, SP2 and ActiveSync is Ver. 4.5.0
phone isnt bricked, your getting into bootloader fine. you need to turn it on, get it into bootloader i mean. if needbe press camera and soft reset (power button) then plug it in USB. You then need to flash your phone with the operator ROM, or the ROM you want to flash it with. Your phone is by far bricked, G3 ones are really difficult to ruin. I learnt that first hand
http://forum.xda-developers.com/showthread.php?p=1560272#post1560272
Think I may have done just that...bricked my phone. G3 wiza200, IPL/SPL 2.26
Cannot get it to read a usb connection at all. Help please?? Thanks in advance
jphuffs said:
At 56%, the desktop went to a blue screen and said an error had occurred and the system must be restarted. The screen asked if I had installed any new programs, check with the adminstrator, etc. The only program recently installed is the program for this ROM revision. When it crashed, the phone had a completion bar in the top 1/3rd, showing 56% completion. The rest of the screen was white. I restarted the desktop and was unable to establish a sync connection. I then preformed a hard reset on the phone. When it restarted, it showed 4 color bars, red on top, green, blue and white at the bottom. Since I cannot restablish a sync connection, how do I finish the modification. I am now concerned that I have "bricked" the phone. I am reluctant to try this mod on another phone until I can determine what went wrong.
Click to expand...
Click to collapse
hi
ur phone is certainly not bricked,cuz ur desktop crashed therefore the phone upgrade cudn't be completed,nothing to worry as long u can get to bootloader mode(Tricolor Screen)
Ok,listen, u do not require active sync connection,to flash a rom,do as I say and it'll be working fine,follow these steps to complete ur upgrade:-
1.Switch on,go to bootloader mode (Tri colored screen).
2.Connect usb cable to the phone and PC
3. After connecting usb cable,u will notice small 'usb' showing on the corner at the bottom of the bootloader screen of ur phone,if it shows,ur r ready to flash and upgrade
4.start the upgrade RUU_ rom u want the to upgrade with
5. complete the flash,let it reboot
let me tell u,u dont need active sync connection to upgrade
cheers
akashastrega said:
http://forum.xda-developers.com/showthread.php?p=1560272#post1560272
Think I may have done just that...bricked my phone. G3 wiza200, IPL/SPL 2.26
Cannot get it to read a usb connection at all. Help please?? Thanks in advance
Click to expand...
Click to collapse
hi
i have read ur situation at thread u have mentioned here,well i can assure u it's not bricked,cuz as sometimes it's able to go to bootloader mode.
The only problem to me seems the usb connectivety problem.
does it charge ?,if not then clearly it' a usb connectivity,if u can manage to get another usb cable and check out,hope it wud clear this doubt
zabardast_1 said:
hi
ur phone is certainly not bricked,cuz ur desktop crashed therefore the phone upgrade cudn't be completed,nothing to worry as long u can get to bootloader mode(Tricolor Screen)
Ok,listen, u do not require active sync connection,to flash a rom,do as I say and it'll be working fine,follow these steps to complete ur upgrade:-
1.Switch on,go to bootloader mode (Tri colored screen).
2.Connect usb cable to the phone and PC
3. After connecting usb cable,u will notice small 'usb' showing on the corner at the bottom of the bootloader screen of ur phone,if it shows,ur r ready to flash and upgrade
4.start the upgrade RUU_ rom u want the to upgrade with
5. complete the flash,let it reboot
let me tell u,u dont need active sync connection to upgrade
cheers
Click to expand...
Click to collapse
I just had this happen to me as well, I got stuck a 29%
Now when I get to bootloader it shows the IPL 2.26 and SPL 2.26 and also a RUU in the top right hand corner. Plug in USB and I get USB at the bottom left but then when I try to launch the RUU with the rom I want to flash I Invalid update tool, download new tool... It wont "Verify information on the device"
**EDIT
Nevermind, I just got Titanium to take... I may be ok... I think the RUU in the vanilla download I got is messed up or something...
Currently ripping through the rom update now. Damn I just got this phone yesterday I was gonna be pissed if I killed it.
Okay, I have the tricolor screen with IPL 2.25 on the left top of the red bar, SPL 2.25 on the left bottom of the red bar, RUU on the right top of the red bar and USB on the bottom left of the screen.
I push the camers button, do a soft reset and launch the ROM update. First window says "Verifying information on your PDA phone. Please wait." After a few moments I get a window that says "ERROR (300) This update utility cannot be used for your phone. Please get newer update utility."
If I try again, I get a window with "ERROR (264) CONNECTION" And an additional message about the USB connection not working. I am using a USB charge/sync cable and not a cradle.
What now?
jphuffs said:
Okay, I have the tricolor screen with IPL 2.25 on the left top of the red bar, SPL 2.25 on the left bottom of the red bar, RUU on the right top of the red bar and USB on the bottom left of the screen.
I push the camers button, do a soft reset and launch the ROM update. First window says "Verifying information on your PDA phone. Please wait." After a few moments I get a window that says "ERROR (300) This update utility cannot be used for your phone. Please get newer update utility."
If I try again, I get a window with "ERROR (264) CONNECTION" And an additional message about the USB connection not working. I am using a USB charge/sync cable and not a cradle.
What now?
Click to expand...
Click to collapse
ok when u swith on the phone what happens ?
does it go to bootloader mood ? or u force it to go bootloader by keeping camera button pressed and doing soft reset ?
well,after geting to bootloader mode,don't reset again just establish usb connectivity and when it show usb in the lower part of the bootloader screen launch ruu and start the flash.if it still stops with an error,post that error,then it means u had a bad flash or no flash at all.are you pretty sure you got it CID unlocked ?
tell you what you do,go to this link download WST tool and apply it,than post the data info it gives here,this will give the present status of your phone,ok
http://forum.xda-developers.com/showthread.php?t=329170
read this sticky:http://forum.xda-developers.com/showthread.php?t=298613
jphuffs said:
Okay, I have the tricolor screen with IPL 2.25 on the left top of the red bar, SPL 2.25 on the left bottom of the red bar, RUU on the right top of the red bar and USB on the bottom left of the screen.
I push the camers button, do a soft reset and launch the ROM update. First window says "Verifying information on your PDA phone. Please wait." After a few moments I get a window that says "ERROR (300) This update utility cannot be used for your phone. Please get newer update utility."
If I try again, I get a window with "ERROR (264) CONNECTION" And an additional message about the USB connection not working. I am using a USB charge/sync cable and not a cradle.
What now?
Click to expand...
Click to collapse
download the wizar-love rom
flash it using the ruu provided..
ftp://xda:[email protected]_Novii+CF2.rar
it should work.....
read this sticky
http://forum.xda-developers.com/showthread.php?t=298613
G4.1 Does you're device start normally (yes) or is it stuck on the three-colored bootloader screen (no)? YES... go to step G4.4, NO go to step G4.2
G4.2 Turn off you're device totaly. Remove the SD card and disconnect the USB cable from you're device. Turn on the device while holding the camera button. You will get into bootloader mode (3 colored screen). Connect the USB cable to the computer and you will see USB at the bottom of your screen above the left softkey (Activesync will not connect in bootloader mode, but you can flash from this screen!). go to G4.3
G4.3 Download wizard_love rom and flash it to your device. Your device should startup again after doing this. Go to G4.4.
G4.4 Is your device CID-unlocked (note: it's not the same as SIM-unlocked!)? YES... go to step G4.7, NO OR DON'T KNOW go to step G4.5. (note: CID-unlocking a G4 is only possible by paying for it at imei-check!)
G4.5 Download enable-rapi.zip. Transfer Cert_SPCS.cab and EnableRapi.cab to your phone. Run Cert_SPCS.cab FIRST and EnableRapi.cab SECOND. Turn your device off and on or wait 5 minutes before soft resetting. Done? Go to G4.6.
G4.6 Follow this great thread by the-equinoxe: [solution] G4 SoftSPL Flash any ROM to CID locked G4 [UPDATED] and load the softSPL on your device using his method. Make sure you take a G4 safe rom (see the thread for details). After the steps you'll have the rom of your choise on your device!
G4.7 You're reade to flash the AKU2, AKU3, WM6 rom of you're choise IF the rom DOESN'T contain IPL/SPL. AKU3 and WM6 roms normally don't contain IPL/SPL. If you want to flash an AKU2 rom, make sure you take the G4 version. If you get an error 300 (invalid update tool) while trying to flash your device look at this thread!
NOTE: If you tried to flash a G3 rom with IPL/SPL in the rom on a G4 you probably will have a bricked device! DON'T flash the new 3.08 and 3.09 IPL/SPL to your G4!
NOTE2: If you got problems flashing with softSPL: Follow this great thread by mun_rus: Solutuion found: how to flash any rom to CIDLOCKED DEVICE. If your device won't start after flashing you can use step G4.2 and G4.3 and try again. Also look at this thread by eddieitman: Faria G4 Step by step installer with instructions to make sure you did all the necessary steps!
Crashed during flash
It has been suggested that I download Wizard Service Tool. OK, I did that. The Wizard Service Tool says to connect to ActiveSync. Can't do that. Phone is locked in Bootloader. It boots up into Bootloader. Any action requiring ActiveSync won't work as long as the phone is locked in Bootloader. Any suggestions as to procedures at this point. Remember, that trying to flash the ROM at this point, I get a message 300 that says I need to get a newer update utility.
Crashed during update
It has been suggested that I flash with wizar-love rom. Did that. Got a message 300, my phone need a newer update utility.
jphuffs said:
It has been suggested that I flash with wizar-love rom. Did that. Got a message 300, my phone need a newer update utility.
Click to expand...
Click to collapse
go to the G4 section and look for the HardSPL thread. Once there get the MUNRUU file from first post and use it with the ROM you wish to flash as it might do the trick of the ERROR 300
crashed during flash
It was suggested that I go to G4, first thread, HardSpl and down load file, munruu. Didn't find any such file. Went to second thread, by mun_rus, but was unable to download file.
My 8125 is locked in bootloader and I don' know what to do.
I still need help!!
jphuffs said:
It was suggested that I go to G4, first thread, HardSpl and down load file, munruu. Didn't find any such file. Went to second thread, by mun_rus, but was unable to download file.
My 8125 is locked in bootloader and I don' know what to do.
I still need help!!
Click to expand...
Click to collapse
this is the thread. and the link is there......
http://forum.xda-developers.com/showthread.php?t=332320
or another thread with link...
http://forum.xda-developers.com/showthread.php?t=334796
jphuffs said:
It was suggested that I go to G4, first thread, HardSpl and down load file, munruu. Didn't find any such file. Went to second thread, by mun_rus, but was unable to download file.
My 8125 is locked in bootloader and I don' know what to do.
I still need help!!
Click to expand...
Click to collapse
download latest Official Rom from carrier official site, establish usb connection while in bootloader flash,it will start working,after that follow the procedure of unlocking and upgrade
or if you have put in Sdcard,remove it and then switch on the device,it might get ok.It's seen in many cases that some Sdcards create problem while upgrade and bootloader screen gets stuck,by removing it,it starts to work fine
good luck
(mestrini;1565518]this is the thread. and the link is there......
http://forum.xda-developers.com/showthread.php?t=332320
or another thread with link...
http://forum.xda-developers.com/showthread.php?t=334796)
My phone is a G3. These links are pretty adamant about being for G4 only
jphuffs said:
My phone is a G3. These links are pretty adamant about being for G4 only
Click to expand...
Click to collapse
I'm talking about the, so called, 'MUN RUU' which are the files used to upload the nk.nbf. You just have to replace those for the ones you're using now; NOT THE nk.nbf, just the others...
zabardast_1 said:
download latest Official Rom from carrier official site, establish usb connection while in bootloader flash,it will start working,after that follow the procedure of unlocking and upgrade
or if you have put in Sdcard,remove it and then switch on the device,it might get ok.It's seen in many cases that some Sdcards create problem while upgrade and bootloader screen gets stuck,by removing it,it starts to work fine
good luck
Click to expand...
Click to collapse
What is "Official Rom from carrier official site"?
The SIM card was removed.
Hope this helps
jphuffs said:
What is "Official Rom from carrier official site"?
The SIM card was removed.
Click to expand...
Click to collapse
For instance, if you are (like me) with TmobileUS, go to the Tmo site and go to the page that gives you the download to rom 2.26. I have that rom, if you are with Tmo, but won't be able to upload it until later...
http://tmobile.infospace.com/tmweb/...wnloadCenter/DeviceDownloads.aspx?deviceID=24
THAT^^^ is for TMOUSA...it is the official Tmo rom. If you are with cingular/att, you need to access their website and download their official rom, etc.
First off, anyone on this forum who has contributed anything, I am have the deepest respect for, and my favorites will get donations as soon as I have money. Ok enough a$$ kissing.
So here is my problem:
I flashed it's right's TNT 6.1 19919 after hardspling. After many problems, like pseudo-hard resetting (turning off, losing all but 6% battery, and changing the date back to what it was originally i.e. 1/27/06) while in a phone call and doing the same while using the wifi, i hard reset and still the same problems occurred. so I undid the hardspl, so now i am back to 2.25.001 in the bootloader but when i connect it to the computer (winxp) to flash the original rom (cingular 2.25) it freezes at 91%. If anyone has had this problem occur or knows the solution as to get ANY rom back on it, IT would be greatly appreciated.
Also after doing some reading I tried to flash wizard love 2.26 to it and that freezes at about 50-60%. so I am stuck and it is really annoying.
Full 8 hour charge, restart computer, different usb port. Same happens: Error 302 Update Error
Hum... maybe when you reCID locked it, you put a CID that's not for that official ROM you're trying to flash. The misbehavior of the phone is due to the ROM you had, not the CID Unlock. If I'm not mistaken, you can hardSPL it again, from bootloader. Then you can try and flash any other ROM you wish. Give my ROM (WM5SE rev5 - if your phone can handle 240MHz - or rev4) a go, after you have CID Unlocked your phone.
My phone can take up to 273 but, all the roms i flashed were g4 safe.... because the ipl spl never changed and i checked them in shell tool . it gives me a update error 302 which wizard love documentation says that the "phone needs a new rom code" which implies that it needs to be taken to cingular, and i dont think i can lie that well. how would one "accidentally" put their phone into bootloader?
theblackhandx said:
First off, anyone on this forum who has contributed anything, I am have the deepest respect for, and my favorites will get donations as soon as I have money. Ok enough a$$ kissing.
So here is my problem:
I flashed it's right's TNT 6.1 19919 after hardspling. After many problems, like pseudo-hard resetting (turning off, losing all but 6% battery, and changing the date back to what it was originally i.e. 1/27/06) while in a phone call and doing the same while using the wifi, i hard reset and still the same problems occurred. so I undid the hardspl, so now i am back to 2.25.001 in the bootloader but when i connect it to the computer (winxp) to flash the original rom (cingular 2.25) it freezes at 91%. If anyone has had this problem occur or knows the solution as to get ANY rom back on it, IT would be greatly appreciated.
Also after doing some reading I tried to flash wizard love 2.26 to it and that freezes at about 50-60%. so I am stuck and it is really annoying.
Full 8 hour charge, restart computer, different usb port. Same happens: Error 302 Update Error
Click to expand...
Click to collapse
You have posted present IPL/SPL 2.25.001,is it 2.25.001 or .0001 ?
As you removed 'HardSPL',did you reflash the appropriate IPL/SPL regarding your phones official bootloader IPL/SPL...?
You shud do the 'HardSPL' again and either do the removal of HardSPL again correctly as instructed in the sticky ' How to remove HardSPL' or Flash any other Rom to recover.
Cheers!
no it was 2.25.001 just a typo. i think i will try these suggestions when i get home and i will post my findings.
A while ago I tried to Flash a version of WM6 from mfrazzz on my wizard. The installation seemed to go ok, but when I boot it up i coudn't get past the second splash screen. I thought the phone was a gonner until last night, when I gave it another shot putting on Button ROM. I followed these instructions and it worked. The instructions also had me unlock the phone, and that worked fine too. after that I tried updating my IPL and SPL, Right now my IPL is 1.05 and SPL is 3.08
After this I tried unsuccessfully to get WM6, I think I started off trying Faria.
(So here is the actual problem)
After I tried installing Faria unsuccessfully, I couldn't get Button ROM back up. I'm stuck on the second splash screen (picture of a mug of beer in front of the Colosseum). I've tried flashing my phone w/ everything i've got, including button ROM and Love, and nothing works. most of the WM6 Update Utilities won't even connect. Button Rom connects, stalls at 98%, finished and says it was a success, but I'm still hung up on the Splash.
(I'm running WinXP w/ SP2)
I really just want something running on this phone, don't care what it is.
Thank you for your time
Download official stock rom to recover back and download WST_4.2.2 to verify the CID lock/unlock status,most probably its still CID locked.or you can even reflash 'Button's Rom' again.
No, I've tried to reflash button rom many times. It says it works but it gets hung up on the splash. Since I can't get anything to run on it WST won't work (I think)
Yes! WST only works on a working OS,have you tried to flash the official stock rom ?
Don't activesync or establish partnership,better if you altogether disable & close activesync and end process 'WCESCOMM.EXE' in the Task Manager and try to end as many applications running at the background.Don't surf the net,disable all anti virus and firewall.
Simply get the phone into Bootloaders mode,hook up with pc via usb cable,watch small usb appear at the bottom of Bootloader screen and run the Rom,hope it'll work.
hEY ZABARDAST
zabardast_1 said:
Yes! WST only works on a working OS,have you tried to flash the official stock rom ?
Don't activesync or establish partnership,better if you altogether disable & close activesync and end process 'WCESCOMM.EXE' in the Task Manager and try to end as many applications running at the background.Don't surf the net,disable all anti virus and firewall.
Simply get the phone into Bootloaders mode,hook up with pc via usb cable,watch small usb appear at the bottom of Bootloader screen and run the Rom,hope it'll work.
Click to expand...
Click to collapse
I did this when my Wizard stucks on the splash...
Get mtty 1.04 i thin i dont remember exactly but the higher i ever saw.
kill process wcesscom in PC
conect the ppc on Bootloader
click on conection it shows USB if not... start up again the process
then a white screen appears
I type: task 28
then it works a little on some memory directions
I type: task 28 55aa [or something] (its better get the info on wiki cause it works on chip directly)
without unplug the PDA starts the RUU again...
It works for me...
This is a process for HTC Universal but it works on Blue angel and Wizard for sure!
wait a little i will confirm the steps and the exactly words to type in.
you might need clean the ROM or your flash ROM is overcooked.
I can repair your phone !
+ Que PPC said:
I did this when my Wizard stucks on the splash...
...
wait a little i will confirm the steps and the exactly words to type in.
Click to expand...
Click to collapse
Hey + Que PPC!
Have you confiirmed those values? And is your Wizard CID unlocked?
This would be great to confirm working so that all those with CID locked devices could get their phones back - without paying IMEI-check.co.suckourmoney.uk
@ twig2256
If your phone is CID unlocked try Drugstore's method of recovering Splash Screen frozen phones
cheers
YES
The values are the same for every DOC CHIP
When the MTTY conects to USB type exactly this...
task 28
(then it will work formating and cleaning the DOC
then it says succesfully clean
and now type...
task 28 55aa
it again works on the same process you can close the mtty without unplug your device... update your device with a Stock rom.
Actualy I have issues with mtty i dont know why i can acces to USB it say CMD GOD Damn can anybody helps...
This is the link that mestrini said for drug gsm store metod to unfreeze
http://forum.xda-developers.com/showthread.php?t=276963
Hey mestrini see this...
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader
even if it is universal it work for Wizard i did it once it works for me. but now it wont why????
zabardast_1 said:
Yes! WST only works on a working OS,have you tried to flash the official stock rom ?
Don't activesync or establish partnership,better if you altogether disable & close activesync and end process 'WCESCOMM.EXE' in the Task Manager and try to end as many applications running at the background.Don't surf the net,disable all anti virus and firewall.
Simply get the phone into Bootloaders mode,hook up with pc via usb cable,watch small usb appear at the bottom of Bootloader screen and run the Rom,hope it'll work.
Click to expand...
Click to collapse
can't solve my t-mobile mda
Dear all,
i am having problem with fist time flash.
Thats what i do:
usb sync the device with vista (wmdc upadated)
run on pc Rhodium-HardSPL_V2_00R3 in automatic mode - nothing happen
run on pc Rhodium-HardSPL_V2_00R3 in manual mode - the device restarts and after three color screen (bootmode) goes to grey screen with with bar and stop at 0% same on the pc after a while on pc i got error 262.
I have tried all the suggestion exsplaned on Hard spl forums
but i am still stuck on it.
Please can you help me
On boot screen i see Rhod10032M spl-0.87.0000
Thanks in advance
same here...
I'm having the same issue. Trying to change the HSPL, get to that gray screen and it sits on 0%, nothing happens. I have an HTC tilt 2 with At&t
Also, not having any luck with the SSPL Manual instal on the device. I copy it over to the device, attempt to run it and the whole thing freezes.
same here, conencted, synced, and tried running the hspl file, get an error, d/led enablerapinew.cab, cant install it, winrar opens it up. havent tried manual mode yet, and i dont plan on it much yet.
Looks like you are having problems.....I would hard Reset it, then go here, http://rhodium.htc-unlocks.com/
Takes you step by step and if you get into a jam, he will help you out.
http://forum.xda-developers.com/showpost.php?p=5084595&postcount=1132
This has been the bible to flashing hardspl. Be sure to follow all the steps provided.
Which roms, radios are currently installed on the devices? Some additional info on the devices might be useful to aide in troubleshooting.
If all else fails do as Pumpiron has suggested.
Please post in the existing thread instead of creating a new one.
Dave