None functioning comm and phone on a dopod 838 - 8125, K-JAM, P4300, MDA Vario Software Upgrading

Hi I know this is abit off topic but is there anybody who can help me with my dopod 838 or HTC Wizard? The pda side of the unit is working great but the connectivity is no working. The phone feature is not working(e.g. can not find any network signal on different providers ) the IR, Wifi, Bluetooth and the GPRS is not working. Worst i can not re flash it becasue the computer only says "Unknown Device" when i connect it via USB. I am using activesync 4.5 on windows xp. It would be a great deal if anyone could help. thank you.
the details are as follows :
ipl : 2.21
spl : 2.21
gsm : 02.19.11
os : 2.21.13.1

Try to upgrade Radio ROM with Wizard connected in Bootloader mode (Camera + reset)

Related

BA / WM5 / Radio 1.06 upgrade

Any advice on how to achieve the upgrade. I have attempted with BAUpgradeUT and and MAUpgradnoid without sucess. My Rom version is 5.03.02 WWE (3/2/05) Radio Ver - 1.06.00, Protocol Ver 1337.38, ExtRom Ver - is blank. Getdeviceid recognises as a PH20B.
Using BAUpg is don't recognise device
Using MAUpg it correctly identifies CE image ver5. it goes to check information on device, Activesync shuts down, then Error 101 connection error
Any ideas ?
Connection error....
Have you tried putting the device into bootloader mode before cradling it?
I initially had the same problem upgrading my BA.
Press camera (media), record, power all at once while you reset. The screen should display "Serial" until you cradle the device, then switch to "USB."
Make sure you run the upgrade program twice, it often fails the first time.
Hope this helps, post again if this doesn't work.
Mick...

HTC Wizard100 not responding after 2_47_11_radio installation

Hi,
I am using HTC wizard 100 with following setup
IPL 1.01
SPL 1.08
GSM 01.12.10
ROM 1.5.4.2 WWE
Radio 01.12.10
Today I tried to install 'radio only' - 2_47_11_radio.
After this my pocket PC is not responding at all.
When I start my cell - it's getting stuck on windows mobile screen, with passowrd on top left corner of task bar and network, speaker and clock displayed in the task bar.
I have goodlink installed in my phone which prompts for the password when I start the phone.However as because it's stuck on the windows mobile screen I am not able to enter the goodlink password also.
And when I reboot GSM information is missing from the initial screen. I am not able to connect my phone using USB cable also.
Can anyone please let me know what I did wrong because of that my phone stopped working. And is there anything that can be done to get it working again.
Thank you for your help and support!
I would say go back to 02.19.11, its so much better then the ones after!!!!
Does anyone know why the sound is gone after increasing the volume up to its maximum?
I'm Using the 12 mb version ,anyone with the same problem?
Hi funman!
Thank you for your reply. Could you please help me out how to get the 02.19.11 installed, as I am not able to connect my phone through USB/ActiveSync. It's stuck on windows mobile screen.
Thank You!
Ok hold the voice button and re-set your phone. Still holding the voice button press the power button till the phone comes back on! Now you should get the boot screen now you just have to connect your usb and there you go run the update prgramm on your computer with the new rom and let it do its stuff!
I had the same problem, and i thought to my self crap. But i was able to down grade my radio rom!!! So dont worry you are able to save your phone!
prince007 said:
Hi,
I am using HTC wizard 100 with following setup
IPL 1.01
SPL 1.08
GSM 01.12.10
ROM 1.5.4.2 WWE
Radio 01.12.10
Today I tried to install 'radio only' - 2_47_11_radio.
After this my pocket PC is not responding at all.
When I start my cell - it's getting stuck on windows mobile screen, with passowrd on top left corner of task bar and network, speaker and clock displayed in the task bar.
I have goodlink installed in my phone which prompts for the password when I start the phone.However as because it's stuck on the windows mobile screen I am not able to enter the goodlink password also.
And when I reboot GSM information is missing from the initial screen. I am not able to connect my phone using USB cable also.
Can anyone please let me know what I did wrong because of that my phone stopped working. And is there anything that can be done to get it working again.
Thank you for your help and support!
Click to expand...
Click to collapse
It's known that 2.xx radios won't work with 1.xx IPL/SPL. Make sure you have unlocked your phone properly, then upgrade to a AKU 2.xx ROm before you upgrade your radio to 2.47.11
vseehua said:
It's known that 2.xx radios won't work with 1.xx IPL/SPL. Make sure you have unlocked your phone properly, then upgrade to a AKU 2.xx ROm before you upgrade your radio to 2.47.11
Click to expand...
Click to collapse
you can get the newest version of youre carriers ROM from www.HTC.com you just have too lok around to find it... should be something like "support by carrier" or something and then in the "downloads" section. good luck
P.S. i dont believe that the phone has to be unlocked to do the carriers shipped roms... my cingular 8125 was NOT CID or SIM unlocked and it worked just fine.

Please HELP ME

hi...
After i tried to update my T-Mobile Vario to high version of WM5, my device worked with out Radio ROM( GSM ROM), not connected by USB with active syn. , when i entered to color screen my computer make beep means conected but when i wana upgrade SPL & WM6 or downgrade to WM5 connection failed..
thnx
Which is your device,G3 or G4 ? First post the vital data of the phone,like IPL/SPL ? which rom were you exactly trying to flash and how you were trying to flash ? only then its possible to help you out.

UpGrade ROM

Hello everybody !
I have a G4 Wizard (Qtek A9100) and I'm trying to update its ROM after read a lot of topics on XDA-Developers (Wizard Windows Mobile 6 for newbies), GFórum and PlusGMS fórum.
IPL: 2.22.0001
SPL: 2.22.0001
GSM: 02.46.11
OS: 2.22.17.1
I already used two diferent chips from two diferent telephone companies which means SIM is unlocked (is that right ?)
After sometime reading I concluded that CIM was locked.
I downloaded HardSPL software and run yesterday.
Now, after HardSPL
IPL: 2.21.0001
SPL: 2.21.Olip
I believe that now CID is unlocked. (Is that right ?)
Then I used RUU from three different ROMs and the same error appears:
ERROR 300: Invalid Update Tool.
"This Update utility cannot be used for your PDA Phone.Please get newer Update Utility"
What does it means ?
What is wrong ?
Tks for your help,
Cássio
Replace the RUU in the Rom with the Mun's RUU provided in the HardSPL thread and run that RUU,it'll work.
ROM UpGrade
Thanks for your help !
Everything works well !
Now it time to learn about WM 6.1 and the new ROM features.
I flashed with Diamond Edition. I know there were a lot of ROMs to be used but this one has info safe for G4...
Does CID unlocked even after the flash I made or if I intent to flash another ROM I need to CID unlock again ? As I used HardSPL I understand it is unlocked.
Tks again for your unique help !!!
Best regards,
Cássio
Thanks! you are most welcome.Yes! it'll will remain semi-permanent Cid unlocked,untill you remove HardSPL,you do not have to apply HardSPL everytime you flash a new rom,just flash as many roms as you wish straight away
Is there any new rom version available for O2 MINI S may be relaeased in 2008.
Zabardast_1,
Now with the new WM 6.1 several questions come up...
1. When I start the Smartphone, a number appears on left upper corner (72410). What does it means ?
2. Wizard doesn't has internat GPS. I have a Deluo GPS antena and I use Destinator software.
Bluetooth is working once Deluo blue light is not flashing (if it is flashing means bluetooth is not connected), but I couldn't until now start using GPS because antena can't find much satellites. There is a set up on Destinator software to configure the GPS but on WM6.1 there is a GPS icon too. Do you know if I need to configure something on WM 6.1 ?
3. Some softwares I had installed on my Storage Card doesn't appears (ShortCut) but they are running when I run using file manager. How can I add these shortcuts on Programs area ?
4. The Wheater tab brings me temperatures in F. Is is possible to configure it to bring in C ?
I noted that battery goes down faster than when I was using WM 5.0 Is it normal ? Is it related to the version of the ROM ?
What differs one ROM from another ROM (considering WM 6.1) ?
I'm sorry for the questions but I'm trying to learn...
Best regards,
Cássio
Sync
Hello,
Some of the problems above I solved, but now I'm facing a serious problem with sync.
I use a Notebook (XP) @ work and another (Vista) @ home.
Everytime I sync with one of them, the other doesn't sync and vice-versa.
What is happening ?
Tks in advance.
Regards,
Cássio
Synch problem
Hello everybody,
I'm still facing synch problems.
Now one more problem come up: Fail to synch due to a register on calendar.
I deleted it on Wizard and on Notebook. Still happening.
Removed and instaled ActiveSync.
Still happening, but this register doesn't exist anymore !
What is happening ? What can I do to fix it and sync with Vista and XP on both Notebooks ?
Thks in advance.
Best regards,
Cássio

Solution to flash ROM from memory card

I need to remote troubleshoot a friend. He put a wrong ROM, i think, and now OS is moving very slowly, does not have GSM, WiFi and neither can connect USB to a Windows 7. Bluetooth works.
Qtek 9100 G3
The boot is:
IPL 1.01
SPL 2.17
OS 1.5.4.2
(no radio)
I do not know if the USB problem is related to ROM or is a communication problem / driver with Win7.
What am I after, and here I need your advice, if is possible to do a ROM flash from the memory card?
Also ANY suggestion is more than welcome.

Categories

Resources