Related
I know there are others experiencing the 28% death wall while trying to flash WM6, but there doent seem to be any specific solutions to this.
I have a Dopod D810 and has already installed 1.30 olipro. Just trying to flash to the official WM6 ANZ Rom. No luck.
Any suggestions guys?
Should just be a very straight forward procedure. Flashing a Dopod with an official Rom.
should be, but it's not... mine is Dopod asia, and stuck at 28% when flashing. Not too sure, but really seemed to me that it was something related to hard-spl. After the 28% error, i reflashed an unofficial rom and tried the official again.
eventually it worked for me.
i guess you don't technically need to manually enter hard-spl first before flashing official ROM.. if anything went wrong i guess you could send it back to them..
safest is to use a modified RUU so it just flashes ROM without IPL + SPL.. i thiiiiiink problem is something to do with SPL
which unofficial rom did u reflash it to? I've been going back and forth with AX3L_OS v3.0.0.2 and the official ANZ dopod rom.
tried about 5 times now. still trying. each time it fails at 28% it's another 10 minutes to flash backto the unofficial rom.
maybe if i try to trce ur steps exactly it might work.
i was flashing to some pdaviet ROM, but i don't think that would make any difference from ax3l's...
have you tried flashing the official ROM with a modified RUU, or you really want the whole package...
If you're just trying to keep everything official i guess you could try to flash the official rom without manually entering bootloader and take your chances. Being that its an official ROM i guess it's safer, or at least covered in warranty..
One question, why don't you try to flash to official WM5 ROM, then to official WM6.. since technically it's supposed to work that way
seriously, i'm not sure why you'd want the official one though.. it's nothing special
Yeah I've tried flashing back to the official WM5 and then WM6, same story.
Tho I havent tried flashing the official WM6 through modified RUU, mainly coz i dont know how to.
Also, In the AX3L version of WM6, there doesnt seem to be a phonepad input method. only keyboard and block recongniser and one other one. Is that coz it's a modified rom, or does WM6 not have the phone pad input. if that's the case i can forget about flashing to WM6 all together.
can't remember if official wm6 has phonepad, but you can just install a cab for it, so it's not a big deal.
look on my site for a link to modified RUU official ROM... instructions are here
i had a lot of problems being stuck at 28%
what eventually i got it to flash to the aus rom was i used SPL 1.20 then it seemed to flash fine.
for some reason my phone doesnt like any other version of SPL besides the one on the latest aus rom either, i flashed to a cooked rom and couldnt flash back until i had put spl 1.20 back in then flashed back to the aus rom.
I have the same problem with 28% stucking
I try to reflash but I still have the same
do you have hard-spl? if so, which version? If you do, flash back a cooked ROM..
if not, you need to try to flash official ROM..
if neither is working, use splxploit. I think all links you need are in this thread already
I have a same problem.
I was upgraded from WM5 to Hong Kong Official WM6 chinese ROM, then I want to change to Official English ROM, I did the Hard-SPL 1.3 and get the SuperCID, but when upgrading the WM6 English officeial ROM, this was stuck at 28%.
Now I was able to flash back to WM5 rom, but I world like to Upgrade to WM6 official ROM, anyone help?
I had this problem when upgrading to the Australian WM6 official HTC Release. The way around it is to run the Trinity Service Provider & CID unlock program from the link below. Dont know why but to use either release, Dopod or HTC WM6 you must run this tool first.
ftp://xda:[email protected]/Trinity/Tools_and_Programs/HTC_Trinity_SIM_CID_Unlock_v1.zip
Hope this helps
you don't *have* to CID unlock your device to use these upgrades..
again, sometimes it gets stuck, sometimes it seems to work.. you can just keep trying.. mine magically worked after a while. the most sure method is to use a modified RUU, of which there's a few on the forums and a few threads regarding these issues..
racerx_ said:
you don't *have* to CID unlock your device to use these upgrades..
again, sometimes it gets stuck, sometimes it seems to work.. you can just keep trying.. mine magically worked after a while. the most sure method is to use a modified RUU, of which there's a few on the forums and a few threads regarding these issues..
Click to expand...
Click to collapse
HI, Thank for your reply, how can I do the modified RUU?
Hi all,
I have success to flash the WM6 official ROM.
this is my experience:
To flash the Radio ROM first, I has flash the 1.50.08.11 Radio ROM.
Then to download the Dutty NBH Tool to take off the Radio DOM of WM6 official ROM.
Then to flash the modify ROM.
Now, my phone is running WM6.
racerx_ said:
you don't *have* to CID unlock your device to use these upgrades..
again, sometimes it gets stuck, sometimes it seems to work.. you can just keep trying.. mine magically worked after a while. the most sure method is to use a modified RUU, of which there's a few on the forums and a few threads regarding these issues..
Click to expand...
Click to collapse
Learn something new everyday. Never knew that simply modifying the RUU would itself allow the updates. Just tried it, and yes it works also.
racerx_ said:
you don't *have* to CID unlock your device to use these upgrades..
again, sometimes it gets stuck, sometimes it seems to work.. you can just keep trying.. mine magically worked after a while. the most sure method is to use a modified RUU, of which there's a few on the forums and a few threads regarding these issues..
Click to expand...
Click to collapse
how do mofify the RUU? and what do I modify it to?
thanx walterjm
Can you share HK-CHT rom for noSPL noIPL noRadio ? Thanks!
WildsideUK said:
I had this problem when upgrading to the Australian WM6 official HTC Release. The way around it is to run the Trinity Service Provider & CID unlock program from the link below. Dont know why but to use either release, Dopod or HTC WM6 you must run this tool first.
ftp://xda:[email protected]/Trinity/Tools_and_Programs/HTC_Trinity_SIM_CID_Unlock_v1.zip
Hope this helps
Click to expand...
Click to collapse
Can you share HK-CHT rom for noSPL noIPL noRadio ? Thanks!
I had the same problem and I resolve it by extract the rom and re-build it ... look at the thread http://forum.xda-developers.com/showthread.php?t=327667
Good luck
Aloha everyone,
I have tried to not post for about 3 weeks but I just can't move forward. I have read and tried to follow everything on the site but I am just confused. I know this is a developers site and I am very intimiated to be castigated by you guys but...it's the internet so what the hell.
I have found numberous instruction threads pertaining to updating ROMS on the Wizard. It seems that up until recently there was only one way to do things but now there are many. As I try to answer questions I come into conflict over which way I shoudl be heading.
I currently have a working WIZ100 that boots with IPL 2.21.0001 SPL 2.21.0lip with GSM 2.25.11 and OS 2.25.11.1. I somehow got to this point, I think by following the instructions to get hardSPL on my device and booting on startup. I did not know if I next needed to find a ROM and if so then how to get that ROM activated on my device or what programs to do this with. I know that the threads spell it out but the threads pertain only to direct assumptions; the assumption that my head is not in my ass.
I wanted to attempt to put a new rom on here, for fun and to play around with something new. Perhaps increase reliability or to get WM6 going. I am stuck now though. Part of me wants to turn back and load the original ROM from the HTC site and the other part of me wants to try a new ROM as I already have this thing booting to the 0lip SPL.
Is anyone out there willing to help me either via this thread, personal message or IM?
Since you have already installed Hard SPL you should be safe to go ahead and pick virtually any ROM you choose on there. I don't have a lot of experience with Hard SPL yet, except for installing it on my kaiser, but the one thing I would guess that you should make sure that the ROM you want to flash doesn't have would be an IPL/SPL update included. As far as I know, I don't think any of the public ones that you find on here have them but make sure you read the chef of the ROM's entire post to make sure. And, if you magically happen to find my ROM somewhere, which you shouldn't since I only gave it to 2 people to try, don't flash it because mine does include an IPL/SPL update.
From my best understanding you have already loaded HardSPL and now are CID unlocked. If this is the case then I would recommend going forward and flashing a new rom to your device. Just go to the Wizard Mobile 6 thread and find one you like, and flash it.
Simple as that.
I appreciate your replies.
1) I am clarified like butter! What program do I download and use to flash the ROM to the Wiz, this has been a source of confusion for me.
2) If I download and install the HTC Cingular ROM from HTC, will that overwrite the HardSPL and return my phone to Factory Default, including the radio areas? In other words do I rid myself of 2.21.0lip?
Thanks for not beating my head in...very polite you devs are...
I like beating people's heads in, and you are far too polite, that I am actually having a very slight guilty twinge! Damn you. I have a G3 myself so I cannot help much, however, I found this sticky which may help.
http://forum.xda-developers.com/showthread.php?t=332320
I do know that once you choose your rom, you open the folder and run the item marked as ruu.
Now if you only had a G3, then I could fry you like the noob you are.
I suppose at some point, I should make a point of reading/learning about G4's. I know they are a far different animal from my G3.
That's the reason I said not to flash a ROM that contained an IPL/SPL upgrade since there is the possibility that it may overwrite Hard SPL, although I'm not positive of that, but better safe than sorry especially if it it's not an official ROM that carries the correct IPL/SPL format for a G4. If it doesn't contain the correct format for a G4 it could ruin your phone. If you flash an official ROM though and it overwrites it you can always just reinstall Hard SPL again and keep flashing. I hope this makes sense.
As for the files you need to flash a new ROM, they're usually included with the ROM. If they're not then just let me know and I'll upload them for you.
Good that you asked before damaging your (expensive) device...
Every Flash version comes with a RUU (Rom Update Utility) you just run that proggy and it does the rest.
To make it easier, look for a rom that states it's G4 safe (no IPL/SPL included), so you don't have to mess around with the inner files. If you want to, begin your tests with the TNT series, the latest build, stated in my sig is G4 safe, after that you'll be able to know the initial procedure.
Good Luck.
Thanks for the info.
Do I execute the ruu from Windows XP or from the SD card ont he device?
Why am I have a hard time searching for and finding TNT 5.2.1921 TouchFlo ROM?
The rom update utlity gives me an error when I try to update. Should I try to do all this from the sd card?
Well, I am plugging along. I rebooted after an error 300 came up on the rom utility. Any suggestions for me?
I found this thread, back in business, thanks for your help guys.
I guess my only unanswered question is...if I use the HTC ATT exe from htc.com will it kill the hardSPL and restore the computer back to normal?
If you have ROM on your desktop, Connect your phone to your computer via USB, open up Activesync, uncheck the check box in settings that allows USB connections. Make sure you have at least 50% battery, then put your phone into bootloader mode. (soft reset while holding down the camera button- keep holding the button for 5 sec.) a tri-color RGB screen should come up. This is boot loader mode. Then run the rom update utility program, and everything is automatic from there on. once it is done flashing the phone will restart itself.
Thresher said:
I found this thread, back in business, thanks for your help guys.
I guess my only unanswered question is...if I use the HTC ATT exe from htc.com will it kill the hardSPL and restore the computer back to normal?
Click to expand...
Click to collapse
Try it and find out. I'd kind of like to know the answer to that one too, although my phones a G3 and already CID unlocked anyway. You can always reinstall Hard SPL over again if it does.
So this worked out well for me overall. Installing HardSPL to my G4, and then using a correct bootloader with the right ROM (to review).
I am having one issue.
I have the OEM ROM, however the RUU gives me an error. Is there a documented way to restore the phone to an original status? Is it even necessary?
I ask due to problems since my upgrade to the TNT rom. I am noticing a lot of missed calls and people have complained. Is this an issue with the 8125 and the particular ROM?
I don't know what to ask, or how to search for this. Thanks for any input you can offer.
Otherwise the TNT rom is awesome. I do miss the voice dialing though. Thats another search.
Actually, that's usually an issue with your radio version. Try using either version 2.19 or farias 2.69 and see if that fixes your problem. You should be able to find both of them in the wiki and you may want to try both of them and see which one gives you the better reception because sometime one will work much better than the other for you depending on your location.
By the way, you don't have to be CID unlocked or have hardspl installed to update your radio so you shouldn't have an issue with the RUU giving you an error. If you do, let me know and I'll upload a different RUU for you to try.
xeno1 said:
Actually, that's usually an issue with your radio version. Try using either version 2.19 or farias 2.69 and see if that fixes your problem. You should be able to find both of them in the wiki and you may want to try both of them and see which one gives you the better reception because sometime one will work much better than the other for you depending on your location.
By the way, you don't have to be CID unlocked or have hardspl installed to update your radio so you shouldn't have an issue with the RUU giving you an error. If you do, let me know and I'll upload a different RUU for you to try.
Click to expand...
Click to collapse
So the Rom is broken up into major parts. Those parts must ineract with one another, so that would be why my radio version may be at cause?
Yep. The ROM can contain the IPL, SPL, OS, Splash Screens, GSM (the radio), and extended ROM, any of which can be changed or upgraded individually without affecting the other parts of the ROM (for all intents and purposes anyway). That means you can change your radio version without it deleting all of your settings or your installed apps in your OS, etc etc.
Since you still upgrade each individual part using a RUU that is able to update any of the parts you still get a warning when you run it that it will delete all of your files, but as long as the update that you're running doesn't include a new OS you can ignore those warnings.
I decided to back out of the entire upgrade and move back to WM5 Official Cingular HTC ROM. I am stoked that I now know the full process of taking a G4 through hardSPL, ROM updates and restoral.
I was too scared to try any radio updates or fixes. Maybe when I upgrade phones I will come back to playing with the 8125 but for now, I just need a good functioning phone for work.
Do these Cingular radio fix cabs apply to a standard phone or only to upgraded ones?
I'm new to all of this, so please bear with me.
I know that the device is G4. I've already played around with flashing to where I've only flashed once and flashed using the Faria G4 step by step...http://forum.xda-developers.com/showthread.php?t=298967
I'd like to try a different ROM, but different things I've read have mentioned flashing back to the original ROM and starting over. However, I don't have the T-Mobile ROM. In the end, I would be using the device on ATT's network. I didn't know if I could "start from scratch" by using the ATT rom (RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1.exe).
I pretty much want to blow away the T-Mobile stuff as I'll never use them.
I'm doing all of this because "something's wrong". It seems that any use of the wi-fi and using IE kills the battery. If I set the power management to anything other than "best performance" I cannot surf the net as everything "times out" and pages don't load.
The reason I started all of this is because I needed the newer version of WM so I could connect to an AP using WPA with AES. The WM5 that was on the MDA didn't have AES.
Any ideas/thoughts/help?
bluesfan77 said:
I'm new to all of this, so please bear with me.
I know that the device is G4. I've already played around with flashing to where I've only flashed once and flashed using the Faria G4 step by step...http://forum.xda-developers.com/showthread.php?t=298967
I'd like to try a different ROM, but different things I've read have mentioned flashing back to the original ROM and starting over. However, I don't have the T-Mobile ROM. In the end, I would be using the device on ATT's network. I didn't know if I could "start from scratch" by using the ATT rom (RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1.exe).
I pretty much want to blow away the T-Mobile stuff as I'll never use them.
I'm doing all of this because "something's wrong". It seems that any use of the wi-fi and using IE kills the battery. If I set the power management to anything other than "best performance" I cannot surf the net as everything "times out" and pages don't load.
The reason I started all of this is because I needed the newer version of WM so I could connect to an AP using WPA with AES. The WM5 that was on the MDA didn't have AES.
Any ideas/thoughts/help?
Click to expand...
Click to collapse
I never flash to an original ROM when trying new ones. I don't believe in the myth that an official ROM provides a strong base for upgrading. It's all a matter of deleting bytes and writing new ones so why bother?
If you don't want operator customizations then just do a hard-reset (loosing all user data) and soft-reset before the customization process. But i strongly advise to try new 6.1 ROMs out there that you'll have a great system to work with (don't forget to use an overcloking/CPU sacling app to get speed)
cheers
mestrini said:
I never flash to an original ROM when trying new ones. I don't believe in the myth that an official ROM provides a strong base for upgrading. It's all a matter of deleting bytes and writing new ones so why bother?
If you don't want operator customizations then just do a hard-reset (loosing all user data) and soft-reset before the customization process. But i strongly advise to try new 6.1 ROMs out there that you'll have a great system to work with (don't forget to use an overcloking/CPU sacling app to get speed)
cheers
Click to expand...
Click to collapse
YUP! Very well said m8 excellent tip and info,cudn't agree more myself.I have never reflashed to any stock rom before any upgrade and never had any problems.
I'll just add here,as you have a G4 device,don't use 'Shell Tool',just 'HardSPL' it and you'll never feel the need to reflash any official stock rom to have a solid base.
Cheers!
zabardast_1 said:
I'll just add here,as you have a G4 device,don't use 'Shell Tool',just 'HardSPL' it and you'll never feel the need to reflash any official stock rom to have a solid base.
Click to expand...
Click to collapse
That's one other thing I wanted to check. The instructions I've read on this site explain pretty well the step by step of going from the original ROM to a new ROM. I followed the "Wizard Windows Mobile 6 for newbies" on the wiki and then used the files from the Faria how-to. Once I've did the HardSPL install steps, is it always there? Or was it overwritten by the new ROM?
I guess I'm wondering what step I would start at for a new ROM...would I just repeat all the steps?
Also, I guess I'll always have to do the soft reset to stop the T-Mobile stuff from loading? If anything, I'd rather have the ATT stuff as I'd use their network and not T-Mobile or just have nothing.
The last thing I don't want is a brick.
Thanks for all the help! This is quite the learning experience and after my first flash I totally "geeked out".
Also, I've notice that it seems some of the ROMs are unclear as to if they are G4 or not. Unless I missed it, is there, by chance, a running list of all the ROMs? Or is it just a matter of reading all the pages of the forum? It'd be handy if there was a list of all the ROMs and if they were G4 or not.
bluesfan77 said:
That's one other thing I wanted to check. The instructions I've read on this site explain pretty well the step by step of going from the original ROM to a new ROM. I followed the "Wizard Windows Mobile 6 for newbies" on the wiki and then used the files from the Faria how-to. Once I've did the HardSPL install steps, is it always there? Or was it overwritten by the new ROM?
I guess I'm wondering what step I would start at for a new ROM...would I just repeat all the steps?
Also, I guess I'll always have to do the soft reset to stop the T-Mobile stuff from loading? If anything, I'd rather have the ATT stuff as I'd use their network and not T-Mobile or just have nothing.
The last thing I don't want is a brick.
Thanks for all the help! This is quite the learning experience and after my first flash I totally "geeked out".
Also, I've notice that it seems some of the ROMs are unclear as to if they are G4 or not. Unless I missed it, is there, by chance, a running list of all the ROMs? Or is it just a matter of reading all the pages of the forum? It'd be handy if there was a list of all the ROMs and if they were G4 or not.
Click to expand...
Click to collapse
Well,once 'HardSPL' applied will remain 'HardSPL' unless you remove it personally to revert back to official stock wm5 rom .Remember,there's no official wm6 upgrade offered by either T-mobile or At&tt,all the wm6 roms available here in this forum are custom build wm6 roms and they don't have any T-mobile or At&tt stuff included in them.
All the wm6 custom build roms are safe for G4 devices as they don't have any IPL/SPL included in them.Only roms with IPL/SPL in it are not safe for flashing to a G4 phone.Even after the 'HardSPL',the official stock rom cannot be flashed,until and unless,first 'HardSPL' is to be removed and official G4 IPL/SPL are flashed back.
Cheers!
Ok, now I understand!
Thanks!
I'm having a lot of fun with this.
At the point I am I need the help of experienced Users from the community.
I flashed a original HTC Wings (S730) with WM 6.1 ROM. It runs perfectly until I got a hardware problem (radio) . This is the reason I have to send it back to the official service.
Therefore I tried to go back to an official ROM from the http://wiki.xda-developers.com/index.php?pagename=WINGS_WM61_Alcaline
At first I flashed the earlier backuped Bootloder via sspl-0.91-wings.exe. This seems to be okay. But as I tried to flash an official ROM from the site mentioned above, during the flashing process I've got the note 'ERROR 294 Invalid vendor ID'. What was wrong? Did I forget any step?
Please, is there anyone who can describe the correct way back to 'warranty' for a newbie?
Thanx a lot.
have you tried all the ROM's? there is one prerelease and two release ROM's.. try both of the release roms, they might be for different production models/locations.
I tried both official released ROM's (signed as 'Ship'), not the prerelease version.
and if you first flash the shiped rom (with hardspl) and when done flash the back-up of the spl
With reference to an earlier statement of bigflavour in the thread http://forum.xda-developers.com/showthread.php?t=383617&page=17
I flashed back the original SPL at first.
Too bad It seems to be that I have a new problem now. Few minutes ago I have tried to reinstall hardSPL on the device via the well known sspl-0.91-wings.exe running on the Wings. But as I started the sspl, the device shows on the display that 'Access denied....is not digitally signed with a trusted certificate'.
Thereupon I thought I had to 'application_unlock' the device. After running the SDA_App...Unlock on my PC the display message shows succesful unlocking process. B U T, the sspl doesn't run as before.
Now, I'm totally confused. What has happened??
It's flavor, and unfortunately, I have no idea how to help you.
Probably tried the European english's spelling hehe.
Also This does seem like an odd problem, have you tried for kicks doing the factory reset to see if it will reset some of the registry and maybe fix your issues? I dont know anything about the spl's since I have no need to upgrade to 6.1, I wouldnt imagine it causing any more damage but again I dont know what all was done. I havnt followed those threads for a long time.
Thanx a lot. Apparently, the hint to make a hard reset hits the mark. Now I flashed back the HardSPL. So I'm back at the starting line . Does anyone knows if the official ROM from the http://wiki.xda-developers.com/index..._WM61_Alcaline is the latest one and can I use it for the warranty return?
Or should I look for an original German HTC ROM?
I was a little bit to fast. I will need a German ROM definitely, because the ROM from the Wiki doesn't include a the german language option.
Is there anyone who can help me with a original HTC S730 ROM for the german market?
Thank you in advance.
Hallo HSN,
if you give me a introduction how I backup my ROM, you can have my one. I own a German HTC S730. But I am confused when I read all threads about flashing etc....
One page introduction how to back up and you can have my one.
But I think that the Repair center here in Germany, doesn't care about the Rom you have installed.
Hi,
I'm trying to upgrade my radio rom. At first everything seems fine but after the upgrade process is at about 30%, I get error no. 114. I think that maybe a part of my rom is broken, so I'd like to change the allocation of my roms. I'd like to have the extented rom part as new radio rom and vice versa.
Is that possible? If yes, how is it done?
thx for your help
PECK
sorry to disappoint you, but no, that is not possible.
start the other way around, do not try to bypass a problem by creating a new one, try solving the problem first. why would the radio rom abort in the middle of the upgrade process?
- do you use the right upgrade tools?
- do you use the right radio rom?
- did you take care of everything else there is about upgrading a rom (bootloader, active sync kill...)?
- are you able to flash another os rom?
...whatever comes to mind when flashing roms, because this problem will not be any different after all.
@ chef_tony:
I've no problem with upgrading the OS or the extented rom! thats why i think that maybe the flash chip is broken!
I tried many different upgrading tools, even one of yours!
I don't know the current language id of my device! Originally it was a german XDA III! How can I check the current language id and how can I change it? is it possible that I have this problem because of a wrong language id?
thx in advance
PECK
i would guess it couldn't have anything to do with the country id, error 114 is radio rom update error.
btw, you get to see the inofficial country id everytime you soft reset the device, and in the bottom right corner it says something like WWE, or GER, for instance. or, when you connect the device and run getdevicedata.exe from the ruu folder, which is done before the upgrade, to show you the "from:" and "to:" numbers.
but: i just got another idea.
do you actually take out the sim card, before trying to upgrade the radio?
is your device sim unlocked?
have you played around with different bluetooth stacks?
have you performed a hard reset before trying to upgrade the radio?
have you tried upgrading the radio from the stock o2 rom wm2003?
ok, that was more than one idea, and downgrading seems like a lot of work, but it is worth a shot. if you spend days flashing (or trying to) over and over again anyways, you might as well try that, would mean 2 extra upgrading sessions, but what is that, like an hour?
oh, and what radio rom does the device have now, stock? or is it a newer one already?
and why do you think you need to upgrade the radio rom anyways? phone not working, maybe the problems lie deeper and that could be why the upgrade process can't work in the first place!
"don't confuse an original symptom with the sickness from the drugs we gave him" as dr. house, would say
hi,
the device is unlocked! there was no sim card inserted during the upgrade; i just tryed with one but I get the same error at 32% progress...
it doesn't work with the original rom, also!
it would be fine if the stock rom was installed, but unfortunately i don't have installed any radio rom whatsoever!
windows mobile device information says that i don't have a radio rom and no protocol installed!
oh, for pete's sake, i'm sorry.
when i asked you about the sim card being inserted, i thought of taking the card out, if you hadn't done before, should have written that. many people have problems when having a sim card or sd card inserted, i didn't want to suggest to put one in! that can never do good, either nothing happens or it gets worse, i really shouldn't have forgotten that.
it doesn't work with the original rom, also!
Click to expand...
Click to collapse
yeah, but does the stock rom itself work? i mean, the stock rom is a so called baked rom, meaning it contains a rom, an extrom and a radio rom, while the cooked roms here only contain the actual rom, so the os. i mean, you could try and extract the radio from the stock rom and try and flash that. it would give you a radio back! or if that doesn't work either, try flashing the entire stock rom, if that works without problems and then you'd have a radio, it means that your issue is too strange to think about, but still you can delete the extrom again and flash another rom without harming the original radio.
wouldn't that be a step forward?
btw. what radio rom are you trying to flash?
if it is just one, you try over and over, are you absolutely certain, this is for the BA? which version is it? what was the original file name of the exe? where did you get it? have you tried re-downloading it, maybe the file is really broken!
hi,
i tryed many different rom versions, and i'm pretty sure they are for the blueangel!
do you know, where i can get a cooked rom for my xda 3?
first, to be clear about that, as mentioned before, cooked roms consist only of the operating system itself and contain neither a radio rom nor an extrom. so about every rom offered here is a cooked rom. but that won't solve your problem, since, as mentioned, there is no radio included. that is why i suggested for you to try the original radio from the shipped rom, and then the entire shipped rom, to determine, whether the radio rom flashes, when it comes after an nk.nbf rom, which would mean, that from now on, you'd have to "bake" roms yourself, by taking cooked roms and adding the radio, so to not lose it. when you can actually flash wm2003 you can also try flashing other radios with the original BAupgradeut, because in contrast to os roms, there should be no limitations to the radio roms, as far as i know.
Change WM german to english or spanish
Hi! I´m new in the forum, please i need some help, i have a qtek 9090 bought in germany so it has a windows mobile in German. Can you help me to change the ROM to an english or spanish version.
The info is:
ROM version: 1.40.01 GER
ROM datum:03/10/05
Radio version: 1.12.00
Protocol version 1337.42
Extended ROM version: 1.40.750 GER
Model: PH20B
Platform: PocketPC
IMEI 353030001525302
Can you explain me step by step or suggest me a page wuere i could find some instructions, i have another problem too, I don´t have a usb cable for it, please help me