Related
I have an 8125 that I can't seem to get off of the RUU screen. It shows IPL 2.25.0001 and SPL 2.25.0001. Every time I try to use the HTC software update it reaches 95% and then errors out. Any idea how I can get this phone working again?
Thanks,
T
you have a G4 wizard, you need to install the wizard love rom. I believe if you read around, you may be able to find out where to find it. Also read some info about unlocking your CID and SIM for a G4 Wizard.
t_matheus said:
I have an 8125 that I can't seem to get off of the RUU screen. It shows IPL 2.25.0001 and SPL 2.25.0001. Every time I try to use the HTC software update it reaches 95% and then errors out. Any idea how I can get this phone working again?
Thanks,
T
Click to expand...
Click to collapse
I found this in another thread, try it.
--------------------------------------------------------------------------------
Hi there,
If you ever happen to get stuck in the IPL / SPL screen, try the following (it happened to me and I almost got a heart attack...):
"If your device doen't boot after flash procedure with my shelltool you should
1) Hold "Camera" while short pressing the "reset" button. Your device will enter in bootloader mode. You will se 3 stripes.
2) You should connect your usb cable to your device and pc and run RUU and flash this rom.
http://rapidshare.com/files/17792050/Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar
3) read my instruction once more and repeat all step by step. its very important!!"
[I've edited the download link for the love rar, the original one on the ftp server was deleted]
t_matheus said:
I have an 8125 that I can't seem to get off of the RUU screen. It shows IPL 2.25.0001 and SPL 2.25.0001. Every time I try to use the HTC software update it reaches 95% and then errors out. Any idea how I can get this phone working again?
Thanks,
T
Click to expand...
Click to collapse
Suggestion.
Go to IMEI Check, buy the unlock and have fun upgrading and downgrading your ROM.
It cost you some money but you can restore your device without to much trouble.
Best regards.
golfernutnflorida said:
I found this in another thread, try it.
--------------------------------------------------------------------------------
Hi there,
If you ever happen to get stuck in the IPL / SPL screen, try the following (it happened to me and I almost got a heart attack...):
"If your device doen't boot after flash procedure with my shelltool you should
1) Hold "Camera" while short pressing the "reset" button. Your device will enter in bootloader mode. You will se 3 stripes.
2) You should connect your usb cable to your device and pc and run RUU and flash this rom.
http://rapidshare.com/files/17792050/Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar
3) read my instruction once more and repeat all step by step. its very important!!"
[I've edited the download link for the love rar, the original one on the ftp server was deleted]
Click to expand...
Click to collapse
I have a 8125 as well and just run the wizard love as above and you will be back in business. As for unlocking you can use latest lokiwiz for free as posted in the forums.
cybercub said:
I have a 8125 as well and just run the wizard love as above and you will be back in business. As for unlocking you can use latest lokiwiz for free as posted in the forums.
Click to expand...
Click to collapse
You can only unlock a G3 Wizard like that. G4's are different and have to be unlocked via imei check. The OP has a G4 based on their IPL/SPL they posted.
I can't seem to get my hands on this file. I've tried several places but no joy. Any thoughts on where I can lay my hands on the Wizard_Love ROM?
Thanks,
T
golfernutnflorida said:
I found this in another thread, try it.
--------------------------------------------------------------------------------
Hi there,
If you ever happen to get stuck in the IPL / SPL screen, try the following (it happened to me and I almost got a heart attack...):
"If your device doen't boot after flash procedure with my shelltool you should
1) Hold "Camera" while short pressing the "reset" button. Your device will enter in bootloader mode. You will se 3 stripes.
2) You should connect your usb cable to your device and pc and run RUU and flash this rom.
http://rapidshare.com/files/17792050/Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar
3) read my instruction once more and repeat all step by step. its very important!!"
[I've edited the download link for the love rar, the original one on the ftp server was deleted]
Click to expand...
Click to collapse
t_matheus said:
I can't seem to get my hands on this file. I've tried several places but no joy. Any thoughts on where I can lay my hands on the Wizard_Love ROM?
Thanks,
T
Click to expand...
Click to collapse
I was able to pull it from RapidShare in the link that you provided. Its also seeded on PirateBay if you prefer the Torrent method...
mfrazzz said:
I was able to pull it from RapidShare in the link that you provided. Its also seeded on PirateBay if you prefer the Torrent method...
Click to expand...
Click to collapse
Got it and now the phone is working again!
So do I need to unlock the phone and install another ROM or will it work fine with this ROM?
Thanks, again for all your help!
T
Based on your original post, you have a G4 Wizard. You can't do the standard unlock like the stickies from Dr. P and Faria describe. You have to use the other sticky for installing roms with a CID locked phone. Your other option is to go to Imei Check and do their unlock (will cost about USD 40). Its all online (you give them your IMEI and some other info with your payment and then they send you the files to do the unlock). But even then, you still have to use G4 roms (so you need to be careful or you'll be back in this situation or worse).
BTW:I've never messed with a G4 Wizard so I'm only stating what I've read. Go read and re-read the CID Locked install procedure in the stickies to learn more.
Hello,
I`m trying to get latest lvsw wm6 to the device.
I own the phone since today.
I made the following steps:
Execute ROMUpdateUltility (Hard-SPL)
->Next->Next->Update
From: Image Version 1.16.407.2
to: Image Version 1.20
->Next -> Next
On the phone:
Enterbotloader.exe
"blabla"
YES
On the computer:
ERROR[246]: Device not responding
On the phone:
IPL-SSPL by Des
SPL-1.07.ds
ok,
trying to run ROMUPdateUltility again...
next next next... he shows me the progress bar --> finished! YES!
Rebooting the phone --> same software version as before the update?
trying to update for 2 hours... just to use gps as advertised
please help, i tried the official Update from HTC -> successfull but effects! programs, contacts etc still there, same version number!
messiah said:
please help, i tried the official Update from HTC -> successfull but effects! programs, contacts etc still there, same version number!
Click to expand...
Click to collapse
I've the same problem [246] upgrading unofficial roms like
GSM_1.41.00.11
and
ROM_ING_WM6_2.27
The only upgrade I make successfully is original
htcp3600-RUU_Trinity_HTC_ITA_1-23-408-2_103_6275_1-38-00-11_108
what's wrong ?
P.S.
I test it using activeSync 4.2 & 4.5
Messiah..... Have you read the very first post in the LVSW ROM thread?
I am NOT having ago, just checking, seems you may have miss-understood.
Grab ALL 3 downloads listed there.
Apply first one, and yes there IS NO real visible change to the phone apart from it has been hard SPL'd
Now apply Second one, will go through the same process BUT the Radio ROM is changed and updated
Now Apply the Third and WM6 is installed
The failure you describe is the computer dropping Activ Sync and then "seeing" the phone in Bootloader mode, which is why it take 2 bites of the first cherry, after that all "should " be ok.
I managed to get mine on the first attempt so it is "Me Proof"[TM] and "Just Works" (c)..... however report back if this hasnt helped
yeah, the process you described tells me that you've loaded hard-spl on your phone.. that's all. No WM6 yet...
I have the same problem.
I have Hard-SPL'ed my Orange M700
Then reboot and reestablish Active Sync
Then I have updated the Radio Rom
Then reboot and reestablish Active Sync
and now it's 1.41.00.11 in settings/system/device information
but when i apply
20070527_Trinity_WM6_v2.0.1.1 it uploads then i power on my device and it's still WM5 ?
What am I doing wrong??
Any help appreciated.
This may be a stupid question but have you SuperCID your device before running the updates?
If you go:
Start -> Settings
System
Device Information
What does it say under Radio version? (Just checks the second step has been completed successfully).
Also when you enter the bootloader what does it say on the screen?
akirainblack said:
This may be a stupid question but have you SuperCID your device before running the updates?
If you go:
Start -> Settings
System
Device Information
What does it say under Radio version? (Just checks the second step has been completed successfully).
Also when you enter the bootloader what does it say on the screen?
Click to expand...
Click to collapse
I thought you didn't need to SuperCID the device (http://forum.xda-developers.com/showpost.php?p=1245390&postcount=70)
My radio Rom shows 1.41.00.11
TBH I don't know. But it can't hurt to try it, I SuperCID mine and it flashes perfectly each and every time.
I'm merely trying to make suggestions that may get a result.
Oh, you didn't tell me what the bootscreen said and what version of Activesync do you have on your PC?
While doing the SuperCID upgrade i was wondering: After flashing any of the ROMs do I reboot or power On manually or wait for the device to reboot itself as the message in the SupoerCID tool suggests:
If radio upgrade went fine, wait until your phone reboots and make sure
ActiveSync is enabled again (you should see green icon in system tray)
Click to expand...
Click to collapse
Stupid Q: How can i make the boot screen stay long enough so i can write it down?
My ActiveSync is 4.5 on WinXP
Rummage around in Start--> Setting --> device ID, and version and stuff...... they are there and you get the same info as on the boot screen... and it stay on longer ;-)
Sorry if a little vague but away from phone at the moment......... erkkkkkkkk
/me runs off to find it so this may get edited
akirainblack said:
TBH I don't know. But it can't hurt to try it, I SuperCID mine and it flashes perfectly each and every time.
I'm merely trying to make suggestions that may get a result.
Oh, you didn't tell me what the bootscreen said and what version of Activesync do you have on your PC?
Click to expand...
Click to collapse
I didnt Super CID just followed the instructions in LVSW 's first thread, applied each DL in order and "it just works" (c)
Thanks. That's where i got the infroramtion from b4. I just thought it might be different in the boot screen.
I now did the SuperCID unlocking and did the 3 upgrades again. after the 3rd upgrade i still have:
- WM5.1.342 Build 15096.3.0.0
- ROM 1.23.61.5
- Radio 1.41.00.11
Q again: Do I need to wait after the flashing or do i immidiately press power
(that's what i do when it says finish) or do i soft reset? Or what else?
Thanks for your help.
Hmmmmm just got me phone....... dont ask
Right CE OS 5.2.1413 build 17745.0.2.3
ROM 2.0.1.1
Radio 1.41.00.11
Sooooo.......
a) are you using LVSW (just to be sure)
b) have you grabbed the latest version posted on page 1 of the upgrading thread?
c) I let it restart it self after it finished flashing, it then reclibrates the screen etc etc
Also looks like you havent upgraded anything just yet ... follow the instructions to the letter and it "should" be fine
a) yes
b) yes
c) there might be the problem i waited 2 mins ans as it wasn't rebooting i just used the power button. How long should i wait aftr the WM6 install?
I soft reset mine directly after the screen goes black. So that should be fine.
Maybe it has to do with my boot loader:
When i go to bootloader i see:
IPL-0.50
SPL-1.07.0000
then it starts fading quickly. is this normal? I have the same fading effect when i install ste 2 the radio ROM. but i still have the new radio rom on as it displays as 1.41.00.11
I again tried to use the 2.0.1.1 it uploads very quickly (maybe 2min) and then it's still the "orange" screen and WM5 on reboot and i still have all my data.
What a I doing wrong?
No. Mine stays there right up until the upload to the phone starts.
Then I get a grey background with a blue progress bar.
What happens if you run Enterbootloader on the phone. Then connect it to the PC.
Then run the install program on the PC.
The first process didn't work.
You should have:
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
Hmmmmm if all else fails try a hard reset on your phone and see what versions of what you have after that.
Did you use ANY form of unlocking prior to using LVSW rom?
/me suspects this might be casuing issues
The radio rom zoooooomed up to my phone and likewise the WM6
I cannt remember reseting the phone after flashing.... IIRC it just worked as in it finished then re-started and way hey off it went.
Also FWIW I just used the DL's in the thread without bothering with anyother boot loaders etc... ie extract flies in first DL into 1 folders, run them, ditto DL's 2 and 3.
I have a stuck image on my 8125. The phone "boots" but only shows a white screen, and is unusable.
The "a2sd all" restore option mentioned in the forums doesnt work for me. I have read on several forums that I should be able to reflash the OS from the bootloader, though I cant find any instructions on how to do this
Could someone point me in the right direction for how to flash an OS VIA bootloader?
Thx
1. Get the phone to bootloader (tree color mode) - I think by soft resetting and pressing the camera button at the same time
2. Connect it to the computer (Windows XP) with a USB cable
3. You will notice "USB" written in a lower corner of the phone (this means it is connected)
4. Now you can flash your provider's ROM without any problems
I am not sure whether the bootloader flashing is possible from Windows Vista.
You must flash normally (in bootloader you cannot use either shelltools or SoftSPL - so use your provider's ROM).
Mirek
Mirek - not to be totally ignorant, but the step 4 is what I'm having problems with .... where can I find either a providers ROM, or something that I can actually use while in bootloader mode?
Thanks!
NM ... Found it!
For anyone reading this .... You can get the provider ROM for the 8125 from HTCAmerica here: http://www.htcamerica.net/support/8125/software-downloads.html
Thanks for your help!
mirekluza said:
1. Get the phone to bootloader (tree color mode) - I think by soft resetting and pressing the camera button at the same time
2. Connect it to the computer (Windows XP) with a USB cable
3. You will notice "USB" written in a lower corner of the phone (this means it is connected)
4. Now you can flash your provider's ROM without any problems
I am not sure whether the bootloader flashing is possible from Windows Vista.
You must flash normally (in bootloader you cannot use either shelltools or SoftSPL - so use your provider's ROM).
Mirek
Click to expand...
Click to collapse
Dear Readers,
I'm having problem with my Dopod 900(,Qtek 9000,HTC Universal,O2 Xda Exec,Jasjar ). Can somebody please tell me what to do?
Before this, every time somebody called, the PDA lost the network bar and start to search or network and reject the calls automatically and also i wasn't able to send SMS. Now, i tried to install WM6 crossbow, the phone even cannot be on !!! even when i connect it to the charger, even the light will not be on. the only page that i can see is a white page asks Press 0 to Restore factory default or press X to exit. either perss 0 or X, the phone will be off and i cant turn it on with power key....
Please tell me what can i do ?? I really need your help.
PLEASE REPLY, PLEASE.
[email protected]
Warm Regards to All
G-Jorji
brick?
hey guys, i need a little help. i downgraded my phone to buttons rom and then i was gonna attempt to upgrade the ipl/slp to 2.xx. so i downloaded the wizard ipl/spl 208 from the ftp site. i had a successful flash but when it went to reboot, my wizard never turn on again. ive searched the forums but it seems to me i have a brick found nothing. has anyone had the same situation happen to them? and find a solution?
it wont turn on at all anymore
acuraholic said:
hey guys, i need a little help. i downgraded my phone to buttons rom and then i was gonna attempt to upgrade the ipl/slp to 2.xx. so i downloaded the wizard ipl/spl 208 from the ftp site. i had a successful flash but when it went to reboot, my wizard never turn on again. ive searched the forums but it seems to me i have a brick found nothing. has anyone had the same situation happen to them? and find a solution?
it wont turn on at all anymore
Click to expand...
Click to collapse
WHAT did you downgrade from?
Did you re-unlock your G3?
How's your battery?
acuraholic said:
hey guys, i need a little help. i downgraded my phone to buttons rom and then i was gonna attempt to upgrade the ipl/slp to 2.xx. so i downloaded the wizard ipl/spl 208 from the ftp site. i had a successful flash but when it went to reboot, my wizard never turn on again. ive searched the forums but it seems to me i have a brick found nothing. has anyone had the same situation happen to them? and find a solution?
it wont turn on at all anymore
Click to expand...
Click to collapse
IPL/SPL 2.08? Does that exist? Do you mean 3.08?
Are you sure your device is a G3? Or you killed it when flashing Button's ROM?
At 56%, the desktop went to a blue screen and said an error had occurred and the system must be restarted. The screen asked if I had installed any new programs, check with the adminstrator, etc. The only program recently installed is the program for this ROM revision. When it crashed, the phone had a completion bar in the top 1/3rd, showing 56% completion. The rest of the screen was white. I restarted the desktop and was unable to establish a sync connection. I then preformed a hard reset on the phone. When it restarted, it showed 4 color bars, red on top, green, blue and white at the bottom. Since I cannot restablish a sync connection, how do I finish the modification. I am now concerned that I have "bricked" the phone. I am reluctant to try this mod on another phone until I can determine what went wrong.
Adding additional info
My phone is a G3, CID and SIM are unlocked, desktop is using Windows XP, SP2 and ActiveSync is Ver. 4.5.0
phone isnt bricked, your getting into bootloader fine. you need to turn it on, get it into bootloader i mean. if needbe press camera and soft reset (power button) then plug it in USB. You then need to flash your phone with the operator ROM, or the ROM you want to flash it with. Your phone is by far bricked, G3 ones are really difficult to ruin. I learnt that first hand
http://forum.xda-developers.com/showthread.php?p=1560272#post1560272
Think I may have done just that...bricked my phone. G3 wiza200, IPL/SPL 2.26
Cannot get it to read a usb connection at all. Help please?? Thanks in advance
jphuffs said:
At 56%, the desktop went to a blue screen and said an error had occurred and the system must be restarted. The screen asked if I had installed any new programs, check with the adminstrator, etc. The only program recently installed is the program for this ROM revision. When it crashed, the phone had a completion bar in the top 1/3rd, showing 56% completion. The rest of the screen was white. I restarted the desktop and was unable to establish a sync connection. I then preformed a hard reset on the phone. When it restarted, it showed 4 color bars, red on top, green, blue and white at the bottom. Since I cannot restablish a sync connection, how do I finish the modification. I am now concerned that I have "bricked" the phone. I am reluctant to try this mod on another phone until I can determine what went wrong.
Click to expand...
Click to collapse
hi
ur phone is certainly not bricked,cuz ur desktop crashed therefore the phone upgrade cudn't be completed,nothing to worry as long u can get to bootloader mode(Tricolor Screen)
Ok,listen, u do not require active sync connection,to flash a rom,do as I say and it'll be working fine,follow these steps to complete ur upgrade:-
1.Switch on,go to bootloader mode (Tri colored screen).
2.Connect usb cable to the phone and PC
3. After connecting usb cable,u will notice small 'usb' showing on the corner at the bottom of the bootloader screen of ur phone,if it shows,ur r ready to flash and upgrade
4.start the upgrade RUU_ rom u want the to upgrade with
5. complete the flash,let it reboot
let me tell u,u dont need active sync connection to upgrade
cheers
akashastrega said:
http://forum.xda-developers.com/showthread.php?p=1560272#post1560272
Think I may have done just that...bricked my phone. G3 wiza200, IPL/SPL 2.26
Cannot get it to read a usb connection at all. Help please?? Thanks in advance
Click to expand...
Click to collapse
hi
i have read ur situation at thread u have mentioned here,well i can assure u it's not bricked,cuz as sometimes it's able to go to bootloader mode.
The only problem to me seems the usb connectivety problem.
does it charge ?,if not then clearly it' a usb connectivity,if u can manage to get another usb cable and check out,hope it wud clear this doubt
zabardast_1 said:
hi
ur phone is certainly not bricked,cuz ur desktop crashed therefore the phone upgrade cudn't be completed,nothing to worry as long u can get to bootloader mode(Tricolor Screen)
Ok,listen, u do not require active sync connection,to flash a rom,do as I say and it'll be working fine,follow these steps to complete ur upgrade:-
1.Switch on,go to bootloader mode (Tri colored screen).
2.Connect usb cable to the phone and PC
3. After connecting usb cable,u will notice small 'usb' showing on the corner at the bottom of the bootloader screen of ur phone,if it shows,ur r ready to flash and upgrade
4.start the upgrade RUU_ rom u want the to upgrade with
5. complete the flash,let it reboot
let me tell u,u dont need active sync connection to upgrade
cheers
Click to expand...
Click to collapse
I just had this happen to me as well, I got stuck a 29%
Now when I get to bootloader it shows the IPL 2.26 and SPL 2.26 and also a RUU in the top right hand corner. Plug in USB and I get USB at the bottom left but then when I try to launch the RUU with the rom I want to flash I Invalid update tool, download new tool... It wont "Verify information on the device"
**EDIT
Nevermind, I just got Titanium to take... I may be ok... I think the RUU in the vanilla download I got is messed up or something...
Currently ripping through the rom update now. Damn I just got this phone yesterday I was gonna be pissed if I killed it.
Okay, I have the tricolor screen with IPL 2.25 on the left top of the red bar, SPL 2.25 on the left bottom of the red bar, RUU on the right top of the red bar and USB on the bottom left of the screen.
I push the camers button, do a soft reset and launch the ROM update. First window says "Verifying information on your PDA phone. Please wait." After a few moments I get a window that says "ERROR (300) This update utility cannot be used for your phone. Please get newer update utility."
If I try again, I get a window with "ERROR (264) CONNECTION" And an additional message about the USB connection not working. I am using a USB charge/sync cable and not a cradle.
What now?
jphuffs said:
Okay, I have the tricolor screen with IPL 2.25 on the left top of the red bar, SPL 2.25 on the left bottom of the red bar, RUU on the right top of the red bar and USB on the bottom left of the screen.
I push the camers button, do a soft reset and launch the ROM update. First window says "Verifying information on your PDA phone. Please wait." After a few moments I get a window that says "ERROR (300) This update utility cannot be used for your phone. Please get newer update utility."
If I try again, I get a window with "ERROR (264) CONNECTION" And an additional message about the USB connection not working. I am using a USB charge/sync cable and not a cradle.
What now?
Click to expand...
Click to collapse
ok when u swith on the phone what happens ?
does it go to bootloader mood ? or u force it to go bootloader by keeping camera button pressed and doing soft reset ?
well,after geting to bootloader mode,don't reset again just establish usb connectivity and when it show usb in the lower part of the bootloader screen launch ruu and start the flash.if it still stops with an error,post that error,then it means u had a bad flash or no flash at all.are you pretty sure you got it CID unlocked ?
tell you what you do,go to this link download WST tool and apply it,than post the data info it gives here,this will give the present status of your phone,ok
http://forum.xda-developers.com/showthread.php?t=329170
read this sticky:http://forum.xda-developers.com/showthread.php?t=298613
jphuffs said:
Okay, I have the tricolor screen with IPL 2.25 on the left top of the red bar, SPL 2.25 on the left bottom of the red bar, RUU on the right top of the red bar and USB on the bottom left of the screen.
I push the camers button, do a soft reset and launch the ROM update. First window says "Verifying information on your PDA phone. Please wait." After a few moments I get a window that says "ERROR (300) This update utility cannot be used for your phone. Please get newer update utility."
If I try again, I get a window with "ERROR (264) CONNECTION" And an additional message about the USB connection not working. I am using a USB charge/sync cable and not a cradle.
What now?
Click to expand...
Click to collapse
download the wizar-love rom
flash it using the ruu provided..
ftp://xda:[email protected]_Novii+CF2.rar
it should work.....
read this sticky
http://forum.xda-developers.com/showthread.php?t=298613
G4.1 Does you're device start normally (yes) or is it stuck on the three-colored bootloader screen (no)? YES... go to step G4.4, NO go to step G4.2
G4.2 Turn off you're device totaly. Remove the SD card and disconnect the USB cable from you're device. Turn on the device while holding the camera button. You will get into bootloader mode (3 colored screen). Connect the USB cable to the computer and you will see USB at the bottom of your screen above the left softkey (Activesync will not connect in bootloader mode, but you can flash from this screen!). go to G4.3
G4.3 Download wizard_love rom and flash it to your device. Your device should startup again after doing this. Go to G4.4.
G4.4 Is your device CID-unlocked (note: it's not the same as SIM-unlocked!)? YES... go to step G4.7, NO OR DON'T KNOW go to step G4.5. (note: CID-unlocking a G4 is only possible by paying for it at imei-check!)
G4.5 Download enable-rapi.zip. Transfer Cert_SPCS.cab and EnableRapi.cab to your phone. Run Cert_SPCS.cab FIRST and EnableRapi.cab SECOND. Turn your device off and on or wait 5 minutes before soft resetting. Done? Go to G4.6.
G4.6 Follow this great thread by the-equinoxe: [solution] G4 SoftSPL Flash any ROM to CID locked G4 [UPDATED] and load the softSPL on your device using his method. Make sure you take a G4 safe rom (see the thread for details). After the steps you'll have the rom of your choise on your device!
G4.7 You're reade to flash the AKU2, AKU3, WM6 rom of you're choise IF the rom DOESN'T contain IPL/SPL. AKU3 and WM6 roms normally don't contain IPL/SPL. If you want to flash an AKU2 rom, make sure you take the G4 version. If you get an error 300 (invalid update tool) while trying to flash your device look at this thread!
NOTE: If you tried to flash a G3 rom with IPL/SPL in the rom on a G4 you probably will have a bricked device! DON'T flash the new 3.08 and 3.09 IPL/SPL to your G4!
NOTE2: If you got problems flashing with softSPL: Follow this great thread by mun_rus: Solutuion found: how to flash any rom to CIDLOCKED DEVICE. If your device won't start after flashing you can use step G4.2 and G4.3 and try again. Also look at this thread by eddieitman: Faria G4 Step by step installer with instructions to make sure you did all the necessary steps!
Crashed during flash
It has been suggested that I download Wizard Service Tool. OK, I did that. The Wizard Service Tool says to connect to ActiveSync. Can't do that. Phone is locked in Bootloader. It boots up into Bootloader. Any action requiring ActiveSync won't work as long as the phone is locked in Bootloader. Any suggestions as to procedures at this point. Remember, that trying to flash the ROM at this point, I get a message 300 that says I need to get a newer update utility.
Crashed during update
It has been suggested that I flash with wizar-love rom. Did that. Got a message 300, my phone need a newer update utility.
jphuffs said:
It has been suggested that I flash with wizar-love rom. Did that. Got a message 300, my phone need a newer update utility.
Click to expand...
Click to collapse
go to the G4 section and look for the HardSPL thread. Once there get the MUNRUU file from first post and use it with the ROM you wish to flash as it might do the trick of the ERROR 300
crashed during flash
It was suggested that I go to G4, first thread, HardSpl and down load file, munruu. Didn't find any such file. Went to second thread, by mun_rus, but was unable to download file.
My 8125 is locked in bootloader and I don' know what to do.
I still need help!!
jphuffs said:
It was suggested that I go to G4, first thread, HardSpl and down load file, munruu. Didn't find any such file. Went to second thread, by mun_rus, but was unable to download file.
My 8125 is locked in bootloader and I don' know what to do.
I still need help!!
Click to expand...
Click to collapse
this is the thread. and the link is there......
http://forum.xda-developers.com/showthread.php?t=332320
or another thread with link...
http://forum.xda-developers.com/showthread.php?t=334796
jphuffs said:
It was suggested that I go to G4, first thread, HardSpl and down load file, munruu. Didn't find any such file. Went to second thread, by mun_rus, but was unable to download file.
My 8125 is locked in bootloader and I don' know what to do.
I still need help!!
Click to expand...
Click to collapse
download latest Official Rom from carrier official site, establish usb connection while in bootloader flash,it will start working,after that follow the procedure of unlocking and upgrade
or if you have put in Sdcard,remove it and then switch on the device,it might get ok.It's seen in many cases that some Sdcards create problem while upgrade and bootloader screen gets stuck,by removing it,it starts to work fine
good luck
(mestrini;1565518]this is the thread. and the link is there......
http://forum.xda-developers.com/showthread.php?t=332320
or another thread with link...
http://forum.xda-developers.com/showthread.php?t=334796)
My phone is a G3. These links are pretty adamant about being for G4 only
jphuffs said:
My phone is a G3. These links are pretty adamant about being for G4 only
Click to expand...
Click to collapse
I'm talking about the, so called, 'MUN RUU' which are the files used to upload the nk.nbf. You just have to replace those for the ones you're using now; NOT THE nk.nbf, just the others...
zabardast_1 said:
download latest Official Rom from carrier official site, establish usb connection while in bootloader flash,it will start working,after that follow the procedure of unlocking and upgrade
or if you have put in Sdcard,remove it and then switch on the device,it might get ok.It's seen in many cases that some Sdcards create problem while upgrade and bootloader screen gets stuck,by removing it,it starts to work fine
good luck
Click to expand...
Click to collapse
What is "Official Rom from carrier official site"?
The SIM card was removed.
Hope this helps
jphuffs said:
What is "Official Rom from carrier official site"?
The SIM card was removed.
Click to expand...
Click to collapse
For instance, if you are (like me) with TmobileUS, go to the Tmo site and go to the page that gives you the download to rom 2.26. I have that rom, if you are with Tmo, but won't be able to upload it until later...
http://tmobile.infospace.com/tmweb/...wnloadCenter/DeviceDownloads.aspx?deviceID=24
THAT^^^ is for TMOUSA...it is the official Tmo rom. If you are with cingular/att, you need to access their website and download their official rom, etc.
I really need all the expert out there to help me on flashing my CHT9110. I'm not sure if flashing CHT9110 is the same as flashing P3600i?
Anyway there is an instruction post by ajajaj and credit to Olipro for the great help. I follow every step stated by ajajaj but still I couldn't get my phone flash to WM6.1, therefore I'm pleading for help here.
Step 1 - Anyway First of all, load the Hard SPL to your phone from : http://forum.xda-developers.com/showthread.php?t=398742
Click to expand...
Click to collapse
From my understanding I need to download the Hard SPL, but what does it mean by load the Hard SPL to your phone? Does it mean I unzip the hard spl and double click ROMUpdateUtility.exe on my PC? I tried to double click anyway and my phone boot to tri-color mode, there my phone get disconnected, doesn't matter I press power, camera button, and push the reset button and my phone start in tri color, again I run the ROMUpdateUtility.exe and this time it run and finish 100% but after that it return an Error[270] Image corrupted.
Then I ignore this first step and proceed to following steps
Step 2 - So, what I did was to download RUU_TRINITY_WM6.1_WWE_ASIA_3.12.YK.Lite extract into its own folder (Mary seems to work as well)
Click to expand...
Click to collapse
Yes I downloaded
Step 3 - then download the custom ruu updated from here: http://forum.xda-developers.com/showthread.php?t=295113 - also get the rombaker for trinity as found further down in the post.
Click to expand...
Click to collapse
Also downloaded
Step 4 - unzip the custom_ruu stuff, put in the downloaded trinity rombaker to replace extracted rombaker,
Click to expand...
Click to collapse
I unzip the rombaker and custom ruu. I overwrite the rombaker into custom ruu/workshop folder
Step 4a - Copy ruu_signed.nbh file that is found in folder created in Step 2 to the rombaker/workshop folder created in step 4
Click to expand...
Click to collapse
I copy the ruu_signed.nbh from WWE_ASIA folder to custom ruu/workshop
Step 5 - then use nbhextract (created in step 4) to extract the ruu_signed.nbh file that is now in the workshop folder
Step 6 - watch the output. (for file names)
Click to expand...
Click to collapse
I extract it and get 00_OS.nb as output
Step 7 - Run the rombaker program and load the extracted files into their places (as referred to in step 6), then click generate NBH
It will ask you to save a file. call it new_nbh (or whatever you want) -
Click to expand...
Click to collapse
I run the rombaker and I fill IPL, SPL, OS, ExtROM, GSM, SubSplash, MainSplash with 00_OS.nb and name the file called new_nbh. So I get new_nbh.txt as the output.
Step 8 - open this file (created in step 7) in notepad, and change the number 400 (about 5 lines down) to 401 save and exit
Click to expand...
Click to collapse
I open with text editor and change the last line to 401 from 400 as below
TRIN100
SuperCID
ROMBaker
XDADevelopers
100,00_OS.nb
200,00_OS.nb
600,00_OS.nb
601,00_OS.nb
900,00_OS.nb
300,00_OS.nb
401,00_OS.nb
Step 9 - then open a dos/cmd/command.com window (whatever you want to call it), cd to the rombaker/workshop folder and then run the following:
nbhgen new_nbh.txt
NOTE: new_nbh.txt should be the same as the filename created in step 7
Click to expand...
Click to collapse
I did exactly been instructed here
copy the generated RUU_signed.nbh file back to the RUU_TRINITY_WM6.1_WWE_ASIA_3.12.YK.Lite folder.
Your p3600i rom is now ready for flashing
Click to expand...
Click to collapse
I copy the ruu_signed.nbh from workshop folder back to RUU_TRINITY_WM6.1_WWE_ASIA_3.12.YK.Lite folder and run the ROMUpdateUtility.exe
After all the next next thingy, it turn black and doesn't go into the tri color. Tried to push power, camera, and reset button and boot in tri color, run the ROMUpdateUtility.exe again it stop at 1%
Can anyone tell me where I went wrong?
Thank and appreciate all your help.
wssoo said:
I really need all the expert out there to help me on flashing my CHT9110. I'm not sure if flashing CHT9110 is the same as flashing P3600i?
Anyway there is an instruction post by ajajaj and credit to Olipro for the great help. I follow every step stated by ajajaj but still I couldn't get my phone flash to WM6.1, therefore I'm pleading for help here.
From my understanding I need to download the Hard SPL, but what does it mean by load the Hard SPL to your phone? Does it mean I unzip the hard spl and double click ROMUpdateUtility.exe on my PC? I tried to double click anyway and my phone boot to tri-color mode, there my phone get disconnected, doesn't matter I press power, camera button, and push the reset button and my phone start in tri color, again I run the ROMUpdateUtility.exe and this time it run and finish 100% but after that it return an Error[270] Image corrupted.
Then I ignore this first step and proceed to following steps
Yes I downloaded
Also downloaded
I unzip the rombaker and custom ruu. I overwrite the rombaker into custom ruu/workshop folder
I copy the ruu_signed.nbh from WWE_ASIA folder to custom ruu/workshop
I extract it and get 00_OS.nb as output
I run the rombaker and I fill IPL, SPL, OS, ExtROM, GSM, SubSplash, MainSplash with 00_OS.nb and name the file called new_nbh. So I get new_nbh.txt as the output.
I open with text editor and change the last line to 401 from 400 as below
TRIN100
SuperCID
ROMBaker
XDADevelopers
100,00_OS.nb
200,00_OS.nb
600,00_OS.nb
601,00_OS.nb
900,00_OS.nb
300,00_OS.nb
401,00_OS.nb
I did exactly been instructed here
I copy the ruu_signed.nbh from workshop folder back to RUU_TRINITY_WM6.1_WWE_ASIA_3.12.YK.Lite folder and run the ROMUpdateUtility.exe
After all the next next thingy, it turn black and doesn't go into the tri color. Tried to push power, camera, and reset button and boot in tri color, run the ROMUpdateUtility.exe again it stop at 1%
Can anyone tell me where I went wrong?
Thank and appreciate all your help.
Click to expand...
Click to collapse
First up you are way ahead of me in getting to the stage where you have been able to modify the nbh, well done.
I am not sure this ROM works even after being modified, but you can give it a go.
To flash the modified ROM.....first put your phone into bootloader mode...ie camer..power and soft reset. It should come up with the tri-colour screen and show SPL Olipro 3.2. something. If it doesnt show Olipro then the Hard SPL you did earlier didn't work.
If it does...connect back to your PC via the USB cable and then run ROMupdate. It will then go through and flash the phone.
All the others have said this ROM flashes and then hangs at the boot screen.
Good luck...let us know how you go.
don't use that ROM... it doesn't work
go HERE to see the ROMs that have been tested and work with the P3600i
there's only 2 (tested) ones there, but at least they work
if those ROMs don't work, i don't know what will - i've tested both myself and they work fine
like andych said, make sure your bootloader (3 colour screen) says Olipro 3.2 on it, to make sure you have HardSPL... otherwise you haven't put that on yet - if you haven't do it again, then flash with a ROM from the link i gave
If I run the ROMupdate when I'm in WM it show
TRIN100
IPL-1.00
TRIN100
SPL-olipro 3.20
But if I boot into the bootloader mode, and I see
TRIN100
IPL-1.00
TRIN100
SPL-3.03.0000
am really confused on how to go about it
joncgde2 said:
don't use that ROM... it doesn't work
go HERE to see the ROMs that have been tested and work with the P3600i
there's only 2 (tested) ones there, but at least they work
if those ROMs don't work, i don't know what will - i've tested both myself and they work fine
like andych said, make sure your bootloader (3 colour screen) says Olipro 3.2 on it, to make sure you have HardSPL... otherwise you haven't put that on yet - if you haven't do it again, then flash with a ROM from the link i gave
Click to expand...
Click to collapse
I just wanna be sure, with the 2 given ROM, I need not do any changing of 400 to 401, and etc? Just run the ROMupdate and everything will run smoothly?
OK
You need to run Hard SPL again.
Connect to your PC and make sure activesync has run properly and your phone is on.
Open Hard SPL and run the ROMupdate. Your phone will go to tricolour and it will come up with a communication error.
disconnect from PC but leave the phone in tricolour....DO NOT reset it.
Cancel our of the ROMupdate. connect the phone to the pc again and run ROMupdate again.
This time it will go all the way through and you will have HardSPL on your phone.
Check it by entering bootloader and it should show Olipro 3.2.
You can then flash away....make sure you always put the phone into bootloader before flashing.
Let us know how you go.
Ok once I get communication error, I disconnect from PC, cancel the ROMUpdate, then I reconnect to my PC again.
This time do I run the Hard SPL or the rom from ajajaj?
I tried both it however reset my phone to tri color and I dont see olipro 3.2 anymore
wssoo said:
Ok once I get communication error, I disconnect from PC, cancel the ROMUpdate, then I reconnect to my PC again.
This time do I run the Hard SPL or the rom from ajajaj?
I tried both it however reset my phone to tri color and I dont see olipro 3.2 anymore
Click to expand...
Click to collapse
You need to run the ROMupdate from HardSPL again......
Only when you have Olipro 3.2 on the bootloader can you run the ajajaj ROM.
Guess it is really giving me a big headache.
Here is my scenario
My phone is on, I connect to activesync and run harl spl romupdate
My phone boot into tri color mode with SPL-3.10.olipro
Then I get error ERROR[260]: Connection
I exit
Disconnect phone from PC
Now comes the part that seems like only I'm the one facing problem.
I connect my phone back to my pc. My phone still in tri color mode I still see SPL-3.10.Olipro
Now I run the romupdate for hard spl again
I see the loading bar but I'm stuck at 0%, then my phone restart and reboot in tri color, now I see SPL-3.03.0000
Alright fine, I reboot on my phone connect to pc run hard spl romupdate till I get Connection error. Now I close romupdate and disconnect from PC.
I reconnect and run the ROM Mary instead. Again failed.
Did I miss any step? Or those are for P3600i and not CHT9110? Any different?
wssoo said:
Now comes the part that seems like only I'm the one facing problem.
I connect my phone back to my pc. My phone still in tri color mode I still see SPL-3.10.Olipro
Now I run the romupdate for hard spl again
I see the loading bar but I'm stuck at 0%, then my phone restart and reboot in tri color, now I see SPL-3.03.0000
Click to expand...
Click to collapse
That's odd. I did what you did - I tried the first time, it failed with the 260 error. I kept the phone in bootloader, disconnected it from the PC, exited and restarted the HardSPL flashing program, and put my phone back in WITH the bootloader still on after that error the came up.
This second time, it worked for me.
If what I have just described does not occur with you, then you cannot flash any ROMs. You MUST succeed with HardSPL first. I don't know what is going wrong for you, I'm sorry Are you using Vista? I only tried on XP.
Also! Watch the screen of your phone the first time you try it from activesync, and make sure security dialogues come up and you approve them. I had to allow them ro proceed.
joncgde2 said:
That's odd. I did what you did - I tried the first time, it failed with the 260 error. I kept the phone in bootloader, disconnected it from the PC, exited and restarted the HardSPL flashing program, and put my phone back in WITH the bootloader still on after that error the came up.
This second time, it worked for me.
If what I have just described does not occur with you, then you cannot flash any ROMs. You MUST succeed with HardSPL first. I don't know what is going wrong for you, I'm sorry Are you using Vista? I only tried on XP.
Also! Watch the screen of your phone the first time you try it from activesync, and make sure security dialogues come up and you approve them. I had to allow them ro proceed.
Click to expand...
Click to collapse
acutally i want to ask after successfully update the hardspl
what number will show?
3.10 or 3.20
mine is 3.20
so strange, but i still can flash to mary rom
joncgde2 said:
That's odd. I did what you did - I tried the first time, it failed with the 260 error. I kept the phone in bootloader, disconnected it from the PC, exited and restarted the HardSPL flashing program, and put my phone back in WITH the bootloader still on after that error the came up.
This second time, it worked for me.
If what I have just described does not occur with you, then you cannot flash any ROMs. You MUST succeed with HardSPL first. I don't know what is going wrong for you, I'm sorry Are you using Vista? I only tried on XP.
Also! Watch the screen of your phone the first time you try it from activesync, and make sure security dialogues come up and you approve them. I had to allow them ro proceed.
Click to expand...
Click to collapse
Well I've tried. The only way for me to accomplish 100% on bootloader is when my phone show SPL-3.02.0000, if I run hard spl romupdate at this point of time, it will complete 100% but sadly after that, it return
ERROR[270]: Update Error
The image file is corrupted. Please check your Update Utility
wssoo said:
Well I've tried. The only way for me to accomplish 100% on bootloader is when my phone show SPL-3.02.0000, if I run hard spl romupdate at this point of time, it will complete 100% but sadly after that, it return
ERROR[270]: Update Error
The image file is corrupted. Please check your Update Utility
Click to expand...
Click to collapse
**Am using Windows XP SP2
i'm sorry, you seem to have a big problem with your phone :/
i don't think we can help you any further - hardspl to get into bootloader the first time, you get the error, you run the program again with the phone in bootloader and the hardspl should complete.
then you can soft reset and it should have 3.20 olipro on the 3-colour screen.
if this doesn't work for you, maybe it won't work at all
wssoo said:
ERROR[270]: Update Error
The image file is corrupted. Please check your Update Utility
Click to expand...
Click to collapse
Which Ruu Update utility did U use? 3.1.3.2 or 3.14.4.1? If you use the one that came with hard-SPL, try using the 3.14.4. U can get this here http://forum.xda-developers.com/showthread.php?t=321182 extract this then change the RUU_signed.nbh with the hard-SPL one, then flash your device as described above.
Argyle0297 said:
Which Ruu Update utility did U use? 3.1.3.2 or 3.14.4.1? If you use the one that came with hard-SPL, try using the 3.14.4. U can get this here http://forum.xda-developers.com/showthread.php?t=321182 extract this then change the RUU_signed.nbh with the hard-SPL one, then flash your device as described above.
Click to expand...
Click to collapse
I'm using the default ruu_signed.nbh that come along with Hard SPL. Unsure what version it is. Anyway I downloaded RUU_TRINITY_WM6.1_WWE_ASIA_3.12.YK.Lite.rar from the net too? Is this you are talking about? I overwrite the ruu_signed.nbh to Olipro's Hard SPL ruu_signed.nbh?
wssoo said:
I'm using the default ruu_signed.nbh that come along with Hard SPL. Unsure what version it is. Anyway I downloaded RUU_TRINITY_WM6.1_WWE_ASIA_3.12.YK.Lite.rar from the net too? Is this you are talking about? I overwrite the ruu_signed.nbh to Olipro's Hard SPL ruu_signed.nbh?
Click to expand...
Click to collapse
Download the RUU_Trinity_DOPODASIA_WWE_3.00.707.18_6275_1.46.30.11_108_Ship.exe then right click to extract (winrar installed). You should see a some files in the directory you extracted to. Find the RUU_signed.nbh, DELETE IT. Then copy the RUU_signed.nbh from the Hard-SPL to the above directory. Run the ROMUpdateUtility.exe.
Sadly I've tried Argyle0297 still getting the same old error msg.
I think it is lock on the SPL or SuperCID is it?
I know how frustrating it is .... this happened to me too.
BUT the one i got is not CHT9110, it's HTC P3600i with chinese rom installed (originally SPL-3.03.xxx). Maybe there's a difference between the two devices. Anyway if you want to give it another try, download the file below. It's the one i successfully used to flash the HardSPL.
Good Luck.
Argyle0297 said:
I know how frustrating it is .... this happened to me too.
BUT the one i got is not CHT9110, it's HTC P3600i with chinese rom installed (originally SPL-3.03.xxx). Maybe there's a difference between the two devices. Anyway if you want to give it another try, download the file below. It's the one i successfully used to flash the HardSPL.
Good Luck.
Click to expand...
Click to collapse
Thank.. am downloading it and will try it right away after work..
Crossing my finger..