Related
Dear All
I would like to have some urgent help on this one. I have downloaded the new Rom Update for my XDAIIs. I have successfully started the ROM update. I reached the screen when it prompted me with the device information and I clicked on UPDATE to start the process. My XDA screen went to Black with the USB indication ...and v2.06 indicated below. Nothing happened and the wizard did not proceed with any further indication except "Checking the information in your device ..." etc...It froze on this and I had to restart my PC. Now my XDAIIs is remaining on the same blacked out screen and won't boot to its previous room if I do a soft or hard reset. Have I "Killed" my XDAIIs? Is there anything I did wrong? Pls HELP !!!!!!!!!!!!!!!!!!
Thanks
Ashraf
No Problem..
1. Do a soft reset (the screen will just blik once and still remain blank)
2. Put the device in cradle/USB
3. ReDo your upgrading procedure by double clicking the upgrade file
It should work then... good luck
same
Guys,
I have the same problem only a little more stupidity on my part, check it out at - http://forum.xda-developers.com/viewtopic.php?p=130797#130797
As you can see kumar00455 your advice doesn't work in my situation
any other help ??
Heath
Kumar
Thanks pal !
I've been able to sort out the problem. I actually needed to stop the Active Sync application on my PC so that the upgrade wizard could connect to the XDAIIs via USB and perform the update. It will not work if the Active Sync task is still running as a process.
After running the app again, the upgrade worked seamlessly without any glitch...!!!
Thanks for your support.
Ashraf
I'd bought my htc p3600 pro (black, free from sim-lock & free from any carrier) from London.
As advised by TRINITYGUIDES.INFO site I tried to do HardSPL with all the three available HardSPL files, but of no avail.
When the HardSPL's progress bar comes(on pc) it gives a message on my phone " Enterbootloader.exe....This may harm your device...Do you want to continue.." I pressed yes & the process stopped & gave an error on pc "Error 246 Device not responding" & on phone screen showed the bootloader with
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
I did soft reset on my p3600 & its working as usual with it original spl infos.
I want to put official WM6 SEA version(ROM+RADIO) on my phone...Please help.
I too have the same message when I try to upgrade to hard spl as per teh guide here: http://trinityguides.info/index.php...ask=view&id=25&Itemid=66&limit=1&limitstart=2
Can anyone help? I have tried updating active synch... could there be anything else?
I have flashed my rom befroe to unlock the GPS but I now want to upgrade to WM6.
I guess the hard spl is a failsafe and I can skip this step?
Thanks
wingnutLP said:
I too have the same message when I try to upgrade to hard spl as per teh guide here: http://trinityguides.info/index.php...ask=view&id=25&Itemid=66&limit=1&limitstart=2
Can anyone help? I have tried updating active synch... could there be anything else?
I have flashed my rom befroe to unlock the GPS but I now want to upgrade to WM6.
I guess the hard spl is a failsafe and I can skip this step?
Thanks
Click to expand...
Click to collapse
Search is great function
http://trinityguides.info/index.php?option=com_content&task=view&id=37&Itemid=67
wingnutLP said:
Sorry!
I am an idiot.
Thanks
Click to expand...
Click to collapse
sorry I tried a Google search on the error message and came up with this thread!
wingnutLP said:
sorry I tried a Google search on the error message and came up with this thread!
Click to expand...
Click to collapse
Search more...
With this link:
http://www.google.com/advanced_search?q=+site:http://forum.xda-developers.com&hl=en&lr=&as_qdr=all
if you search error 246 you will get the solution on 11th answer.
Search more...
Have the same [Error 246]! How can I definitly fix it?
Hi,
first of all, sorry for my poor English. I try to explain my problem so good I can... I hope you can help me.
I have the "[Error 246] Device not responding" problem.
I have used a lot the "search"-function and I have found a lot of posts which propose the same solution "restart the Rom upgrade another time". Ok I did it and my PDA works very well, but now I would like to solve the problem radicaly... How can I solve this problem? Should I use SPLexploit (I have found the guide on trinityguides.info) and then reflash a Hard-Spl?
Thx a lot
ciao
Tompo
Some specifications....
Sorry.... I have a P3600 White with Olipro 1.20 and rom Elias 1.9 SE Lite...
Tompo81 said:
Hi,
first of all, sorry for my poor English. I try to explain my problem so good I can... I hope you can help me.
I have the "[Error 246] Device not responding" problem.
I have used a lot the "search"-function and I have found a lot of posts which propose the same solution "restart the Rom upgrade another time". Ok I did it and my PDA works very well, but now I would like to solve the problem radicaly... How can I solve this problem? Should I use SPLexploit (I have found the guide on trinityguides.info) and then reflash a Hard-Spl?
Thx a lot
ciao
Tompo
Click to expand...
Click to collapse
Before flash manually enter bootloader. After start the rom update utility. (As www.trinityguides.info suggest). You will not get error 246 any more
thanks for answer
Many thanks for anwser...but...
Is this the only solution? If is so, then everbody has this problem, isn't so?
Ciao
Tompo
Tompo81 said:
Many thanks for anwser...but...
Is this the only solution? If is so, then everbody has this problem, isn't so?
Ciao
Tompo
Click to expand...
Click to collapse
www.trinityguide.info
Here is written to flash rom you should manually enter to bootoader. In this case, you will not have error 246.
Most of the people know this, so they have not this problem
Those who not manually enter bootloader can get error 246, and this way of flashing is not as safe as the manual bootloader way.
(because in this case you use the spl uploaded by RUU, not the hard-spl on the PDA)
Ok, now I really understand
Ok, this is a very good anwser, short and clear... thanks...
Ciao
Tompo
fktsndr said:
www.trinityguide.info
Here is written to flash rom you should manually enter to bootoader. In this case, you will not have error 246.
Most of the people know this, so they have not this problem
Those who not manually enter bootloader can get error 246, and this way of flashing is not as safe as the manual bootloader way.
(because in this case you use the spl uploaded by RUU, not the hard-spl on the PDA)
Click to expand...
Click to collapse
When i connect my touch hd to pc in active sync mode, then shutdown device an run in bootloader (volume down and power button at same time) i get the tricolor screen and after a while i get the progress bar on my phone and on pc. But i stays on 0% and says 'update error' after a while.
please help
I Have the Same Problem the Status bar Freeze On 0% and nothing happened
Until the Update Error Message Displayed
Please Advice
Thank You
Note: I Have HTC Diamond2 (Topaz) Without Sim Louk
Hi Me has the trinity 3600 as a VPA GPS vodafone branding, and i get the same error message trying to run the bootloader and entering tricolor screen, ---> error 246 aber manually starting into bootlaoder and restatrting the romupdateutil.exe same error 260 no connention...
So you guys have a working version of the updating ?
And please remove all the links which are not working, linking a solve for the 246 problem, there are nomore links available...
thanks
Dome
I found a way to solve the problem 246 go in you mobile device, -->start -> settings-> connections ->USB to PC open this. Remove the hook @ Advanced networksettings activation! ---> click OK--> close
try again the bootloader etc, then on the tricolore reboot screen is shown USB in the lower white field and the bootloader can do its routine complete.
Have Fun with flashing the phones!
Testet with original German Vodafone available ROM " vpa_comp_gps_RUU_Trinity_VF_DE_1_23_162_4_6275_1_29_00_01_13000_108_Ship.exe "
testet with ZackMcRofls superfast german rom " RUU_Trinity_GER_1.23.162.2_GPS_v3f_by_ZakMcRofl "
testet with
" htcp3600_RUU_Trinity_HTC_GER_1-23-407-2_103_6275_1-38-00-11_108 "
First was Zack´s rom, 2nd. was Original Rom, 3. was Trinitys rom, after trxing all, i flashed Zacks Rom again, it was the best in my view.
Thank you verymuch, bb
According to the unlocking manual quoted below, i have succussfully been to the last step by one, but there is a problem i cannot solve it on my own, please help.
My phone is AT&T TyTN II 8925, my present state is:
(1) i have loaded RUU_kaiser_QSKOM2.3_full;
(2) i come the tri-color screen showing;
KAIS1*0 MFG
SFL-1.0.OliPof
CPL-8
(3) i tried for many times "kaiser-simunlocker.exe". but it always fails me, i.e. it cannot be run at all, no matter how i clicked the icon of the above-mentioned .exe file.
thanks a lot!
====quote====
1. Make sure you installed HardSPL as follows: power off and then press power on while keeping camera pressed, this will enter the so called bootloader mode and you see a tri-color screen (Red, Green, Blue). You should see "SPL-1.0 OliPof" on the second line in the top left corner. You can exit this mode by means of a "soft reset": press the reset button with the stylus.
2. Make a note of the radio version that is currently installed. You see the version strings in the splash screen which appears soon after power on (e.g. "R 1.27.14.09"). Since we will flash a special radio in step 5 you need to flash back your original radio in the last step. You can download radio roms from XDA devs here: http://forum.xda-developers.com/showthread.php?t=349375
3. Connect PC and Kaiser with a USB cable and keep it connected until the last step.
4. Power on the Kaiser and let it boot into Windows Mobile. On the PC make sure the activesync icon is green
5. After you unpacked the download you see directories "step1" and "step2". Go into "step1" and run KaiserCustomRUU.exe. This will flash the special patched radio rom. Follow the instructions until it is finished.
6. Power off your Kaiser and insert a 'strange' SIM, i.e. a SIM from another provider than the one your phone is locked to.
7. Once Windows Mobile has booted up it will show a window called "Simlock" and a textbox where you can enter a 8-digit unlockcode. Now perform a soft reset by pressing the reset button *but* at the same time keep the camera button pressed. If you did it well you will be back in bootloader mode and you see the tri-color screen. The best technique is to press and hold the camera button first and then shortly press the reset button with the stylus.
8. On your PC go into the "step2" directory and run "kaiser-simunlocker.exe". If all went well you will see the unlockcode on your monitor and your Kaiser is being restarted automatically.
====unquote====
turn off allow usb connection on active sync then it should start and once finished click back allow connections
Start > Run > "cmd"
Then browse to the location of the file, and run it from the command line.
Hello,
I am having the same problem trying to run Simunlocker. I did everything it says in the instructions and now I'm at the Tri-Color screen where it says:
KAIS1*8 MFG
SPL-1.8.OliPof
CPLD-8
And in the white block on the bottom it says USB
The Active Sync is gray and when I ran Simunlock.exe in Command Prompt it says:
C:\Documents and Settings\Administrator>"C:\Documents and Settings\Administrator
\My Documents\Kaiser Unlocker\kaiser-simunlocker\step2\kaiser-simunlocker.exe"
=== Kaiser Sim Unlocker (c)2008 by jockyw2001
=== Donations happily accepted, paypal to [email protected]
\\.\WCEUSBSH001: Permission denied
cannot connect to \\.\WCEUSBSH001
Everything else went smooth, but I noticed when I was loading the Kaiser Custom RUU.exe it was done very quick, in about a minute when it says it will take 10 minutes.
Am I doing something wrong? Can anyone help please!!
Thanks
Tina
Sorry, I probably didn't read enough before I asked
I found the problem and everything is working great now Thanks!!
Again, I apologize, but for a Newbie it's quite confusing and not so easy to find out what you 're needing...
Thanks
out of unlock times
I got to step 7 Simunlock screen
"you have tried 6 times, please wait until timeout.."
anyone know how to reset this please help
thanks you guy
please can u help me
Tina0305 said:
Sorry, I probably didn't read enough before I asked
I found the problem and everything is working great now Thanks!!
Again, I apologize, but for a Newbie it's quite confusing and not so easy to find out what you 're needing...
Thanks
Click to expand...
Click to collapse
please i need your help in this,i have try this and all i am having in the step 1 is a blank face not loading into windows,i am confuse and if i think of going to step 2,the dos come and go immidiately.how can you help me out
Completenutter2 said:
Start > Run > "cmd"
Then browse to the location of the file, and run it from the command line.
Click to expand...
Click to collapse
please i need your help in this,i have try this and all i am having in the step 1 is a blank face not loading into windows,i am confuse and if i think of going to step 2,the dos come and go immidiately.how can you help me out
make sure you disable active sync usb connections
HOW?
Tina0305 said:
Hello,
I am having the same problem trying to run Simunlocker. I did everything it says in the instructions and now I'm at the Tri-Color screen where it says:
KAIS1*8 MFG
SPL-1.8.OliPof
CPLD-8
And in the white block on the bottom it says USB
The Active Sync is gray and when I ran Simunlock.exe in Command Prompt it says:
C:\Documents and Settings\Administrator>"C:\Documents and Settings\Administrator
\My Documents\Kaiser Unlocker\kaiser-simunlocker\step2\kaiser-simunlocker.exe"
=== Kaiser Sim Unlocker (c)2008 by jockyw2001
=== Donations happily accepted, paypal to [email protected]
\\.\WCEUSBSH001: Permission denied
cannot connect to \\.\WCEUSBSH001
Everything else went smooth, but I noticed when I was loading the Kaiser Custom RUU.exe it was done very quick, in about a minute when it says it will take 10 minutes.
Am I doing something wrong? Can anyone help please!!
Thanks
Tina
Click to expand...
Click to collapse
Hey Tina,
I am facing the same problem as u had.
I finished step 2 and added the sim card to the phone.
The phone got locked so I removed the card and unchecked the USB synchronization and then place the card back in the phone.
I ran the Kaiser-simunlock in step 2 and I am having the same error:
\\.\WCEUSBSH001: No such file or directory
cannot connect to \\.\WCEUSBSH001
Can you help me? or can anyone help me to unlock this phone.
I am too close to breaking the phone into pieces.
Thanks
hey i know how to do that:
send me a email at [email protected] and I will show how to unlock it.
Hi guys,
I am asking if there is anyone kind enough to help me with my kaiser...?
the issue is the following, the first week wm 6.1 was released I upgraded my kaiser with no problem until last weekend.
last weekend navigating through your forum I decided to install TF3D and a hardSPL was recomended, I downloaded the file SJ_JumpSPL1.93-KAIS and run it on my kaiser. I believe the process got stuck on the 3 color display, I rebooted the kaiser and it seemed ok... but I am not able to navigate the web neither by GPRS or 3G...
this morning I tried to reinstall the kaiser from scratch with a RUU named _HTC TyTN II_RUU_Kaiser_HTC_WWE_Brightpoint_US_3.29.422.1_radio_sign_25.83.40.02_1.70.18.02_Ship
which I downloaded from the HTC website but an error didn't allow it to be complete: ERROR 294: INVALID VENDER ID
HDa3-KBKV5867-HUEbc572-KBKV55670
my goal is to update my kaiser to the look as the TF3D or the amine 2.0 or the Hiperdragon.
I ask anyone of you gentleman to URGENTLY help me fixing my kaiser as this my office tool...
gomesmachado said:
Hi guys,
I am asking if there is anyone kind enough to help me with my kaiser...?
the issue is the following, the first week wm 6.1 was released I upgraded my kaiser with no problem until last weekend.
last weekend navigating through your forum I decided to install TF3D and a hardSPL was recomended, I downloaded the file SJ_JumpSPL1.93-KAIS and run it on my kaiser. I believe the process got stuck on the 3 color display, I rebooted the kaiser and it seemed ok... but I am not able to navigate the web neither by GPRS or 3G...
this morning I tried to reinstall the kaiser from scratch with a RUU named _HTC TyTN II_RUU_Kaiser_HTC_WWE_Brightpoint_US_3.29.422.1_radio_sign_25.83.40.02_1.70.18.02_Ship
which I downloaded from the HTC website but an error didn't allow it to be complete: ERROR 294: INVALID VENDER ID
HDa3-KBKV5867-HUEbc572-KBKV55670
my goal is to update my kaiser to the look as the TF3D or the amine 2.0 or the Hiperdragon.
I ask anyone of you gentleman to URGENTLY help me fixing my kaiser as this my office tool...
Click to expand...
Click to collapse
Why do people continue to screw up their phones by not reading, not understanding what they are doing, and doing things half the way. Are you all just rich and don't care about bricking a $500 dollar phone ? You are lucky you are able to recover your phone at all
Jumpspl is not hardspl . Jumpspl transitions your phone from stock spl to hardspl. You cannot flash any rom stock or custom ,that isn't specifically made for your carrier, until you have hardspl on your phone.
Read thoroughly and follow all the steps here, do not take short cuts and do not skip ahead,
http://forum.xda-developers.com/showthread.php?t=433835
canot do.....
Dear denco7
let me start to thank you for your help and specially point of view... jejejeje
no I am not crazy to ruin my kaiser and as you know it isn't a cheap phone to try to play with it without knowing what you are doing... anyway, that is why forums like this exist and specially kind people like you to help us crazy people... jejeje
well,
i followed your instructions carefully until number 6 on the list. once I tried to run any of the jumpSPL files this error message apeared in my kaiser
"The file 'JumpSPL1.56-KAIS' cannot be opened. Either it is not signed with a trusted certificate, or one of its components cannot be found. If the problem persists, try reinstalling or restoring this file."
which I did and once again no luck....
Are you patient enough to continue helping me?
Dear denco7
let me start to thank you for your help and specially point of view... jejejeje
no I am not crazy to ruin my kaiser and as you know it isn't a cheap phone to try to play with it without knowing what you are doing... anyway, that is why forums like this exist and specially kind people like you to help us crazy people... jejeje
well,
i followed your instructions carefully until number 6 on the list. once I tried to run any of the jumpSPL files this error message apeared in my kaiser
"The file 'JumpSPL1.56-KAIS' cannot be opened. Either it is not signed with a trusted certificate, or one of its components cannot be found. If the problem persists, try reinstalling or restoring this file."
which I did and once again no luck....
Are you patient enough to continue helping me?
gomesmachado said:
Dear denco7
let me start to thank you for your help and specially point of view... jejejeje
no I am not crazy to ruin my kaiser and as you know it isn't a cheap phone to try to play with it without knowing what you are doing... anyway, that is why forums like this exist and specially kind people like you to help us crazy people... jejeje
well,
i followed your instructions carefully until number 6 on the list. once I tried to run any of the jumpSPL files this error message apeared in my kaiser
"The file 'JumpSPL1.56-KAIS' cannot be opened. Either it is not signed with a trusted certificate, or one of its components cannot be found. If the problem persists, try reinstalling or restoring this file."
which I did and once again no luck....
Are you patient enough to continue helping me?
Click to expand...
Click to collapse
What do the numbers say on your bootloader screen ( tricolored)?
it doesnt get that far, as soon as I doble click on the jumpspl file it shows that error message. the tricolored screen never apears
gomesmachado said:
it doesnt get that far, as soon as I doble click on the jumpspl file it shows that error message. the tricolored screen never apears
Click to expand...
Click to collapse
Press and hold camera button and power button and do a soft reset to get into bootloader to see what it says.
gomesmachado said:
it doesnt get that far, as soon as I doble click on the jumpspl file it shows that error message. the tricolored screen never apears
Click to expand...
Click to collapse
Thats because you're not making it go to that screen..
Press and hold camera button and press reset
it says:
KAIS130
SPL-3.28.000
CPLD-8
gomesmachado said:
it says:
KAIS130
SPL-3.28.000
CPLD-8
Click to expand...
Click to collapse
Go to the wiki and find the original rom from your carrier and flash that ie: AT$T , T- Mobile, orange , 3 etc. Then after doing trhat try all the steps in the flashing for noobs thread again.
the only problem is that I bought the phone not from a carrier but from a store in Portugal and the phone was unlocked...
do you think I can still find the original ROM?
I couldnt find any suitable rom for my device I tried:
_HTC TyTN II_RUU_Kaiser_HTC_WWE_Brightpoint_US_3.29.422.1_radio_sign_25.83.40.02_1.70.18.02_Ship
with no luck.
help me please...........
gomesmachado said:
I couldnt find any suitable rom for my device I tried:
_HTC TyTN II_RUU_Kaiser_HTC_WWE_Brightpoint_US_3.29.422.1_radio_sign_25.83.40.02_1.70.18.02_Ship
with no luck.
help me please...........
Click to expand...
Click to collapse
It is not 3.28.410.0 on this list ?
http://wiki.xda-developers.com/index.php?pagename=Kaiser_ROMs
Help me Denco7 you're my only hope.
Denco7,
I tired to run the file that you told me with no luck.
it showed the same message of before:
ERROR 294: INVALID VENDER ID
what else can I try to fix my phone?
Does this help
http://forum.xda-developers.com/showthread.php?t=335568
http://forum.xda-developers.com/archive/index.php/t-425558.html
Hello. I'm new in here. half hour ago I got registered. so i have a problem with my HTC. For about 1-2 weeks now the device was restarting. 2 days ago the device never opened again. yesterday I tried the hard reset sequence and the device open to the message that i will lose everything and if i agree to press send but when i press it i get a green screen and nothing more. what can i do? what might be the problem? I uploaded also a video (but I can't post it cause I am a new user so ask me to send it as a pm) and a photo of the green screen.
thank you very much.
By all means, if you don't mind losing data that you had on the ROM memory, then hardreset.
Hard resetting I think is the best possible solution for you.
So press that green phone button when it tells you to ^>^
I already did a hard reset. that's why i have that green screen. I did a hard reset about 4-5 times now. thanks for your answer.
Ah, I see.
Try this:
Soft reset your phone while holding the camera button.
Does this get you to a screen where it's Red/Blue/Green/White Screen?
If it does, try plugging in a USB cord. If you get this far and see the word 'USB' in the lower left hand corner, then I think we can continue on.
I did it and it shows usb. what next?
Awesome, I'm glad.
Next, Download and run the .exe:
http://rapidshare.com/#!download|16..._4.17.405.2_4.1.13.44_02.94.90_Ship.exe|56629
After this, all should be well.
Now if you want to flash custom ROMs like the ones that I make, just follow the directions on any one of my ROM threads from Top to Bottom ^>^
before i continue. after the installation i will have the OS back? I will have to install it again? i had WM6. thank you very very much for all the help.
error 300: INVALID UPDATE TOOL.
THIS UPDATE UTILLITY CANNOT BE USED FOR YOUR PDA PHONE. PLEASE GET NEWER UPDATE UTILITY.
that's the message i got.
Hmm, okay, try searching mediafire for the user aizend1985 and look for an .exe entiled Wing something or another.. I'm out right now, so cant get the link for you.
Download and run.
i can't find the user. i'll try again. when you have the time please send me. again thankl you very much. have a great time.
Here you go mate, try this:
http://download1152.mediafire.com/he785npun6pg/yj1oz2m3mzm/TMo_Wing_RUU_Update_4.26.531.4.exe
If this doesn't work I'll try to do some research for you and see what we can do.
Error 244: Invalid model id.
Okay. The last thing you can do is to try the dutch vodaphone herald version:
http://rapidshare.com/#!download|18..._4.21.172.1_4.1.13.44_02.94.90_Ship.rar|52629
Download and run the .exe from the Red/Blue/Green/White screen.
If this loads onto your device, then what we do is we HardSPL next.
*crosses my fingers for ya*
If this doesn't work, then have HTC try to repair it. Because I don't think there is anything else to do for it :1
:'( Error 244: Invalid model id.
thank you very much for everything. at least I know that it can be fixed.
you reflashed your phone in some custom roms?
but it didnt work still and you tried the hard spl too.... can you tell me the history of your phone before it went like that, i am a technician and might help you on your problem.... what was the last thing you did on your phone? i will wait for your reply if it's ok....
dear [email protected]
I have the HTC P-4350 for the last 5 years. the last 1-2 weeks the phone started to freeze and the screen went white slowly and then restart. after the 2 weeks the phone closed and didn't open again but the hard reset is working until the part that said format done (or something like that) and then i get a green screen (see the photo I have attached here). after that i made this post and the friend Tribulattifather (member of the site here) helped me with some info and gave me some files to try and install but the first file gave me this message
"error 300: INVALID UPDATE TOOL.
THIS UPDATE UTILLITY CANNOT BE USED FOR YOUR PDA PHONE. PLEASE GET NEWER UPDATE UTILITY."
and the other gave me
"Error 244: Invalid model id.".
there isn't something else. any idea?
thank you.
what is your spl number and ipl....
did you do the HARDSPL on your phone????
do the hardspl first and then flash your phone using a micro sd....
tell me if you already did that.... i will wait for your reply....
i also want to know if you dropped it or something before it went like that.... plz tell me the whole history of your phone....
to my perspective, the phone's problem can be resolve in flashing....
tell me if you hardspl it,,,, because you cant flash it on some ROMS if it's not HARDSPLed...
hi [email protected] i had a problem with my internet that's way I answer now after all that time. I droped it a couple of times by accident but that is a long time ago. the IPL is 4.17.0001 ans SPL 4.17.0000. i never did anything like hardspl. i changed the flex cable 5 months ago. when i first got the phone 5 years ago it had WM5 and after 5 months when i bought it I got WM6 at service. i never got the phone to service cause never anything happen. i can't remember anything else know.
I have an update for my device. now it doesn't open with anything. i mean i can open it to hard reset or to see the spl. it doesn't respont to anything.
May be time to put the phone to rest, mate u.u
I'll play the taps..