hi,
i have same problems with bluetooth and my parrot 3100. anybody?
thanks
Hi, as I posted before, I have problems with the vocal instructions of Tomtom6 . If I connect my Trinity with parrot CK 3100, the calls work, but the navigator instructions remain on PDA's loud- (so to say) -speaker. Is it the same for you?
VOIP SIP HTC Fuze
Installed and configured VOIP config tool on my WM 6.1 but it never works.
It shows Selected Internet calling but when i try to call ,,it fails without any error.'
Mani
Related
Hi all,
The TyTN was never great at this and it *appears* the Kaiser may be no better. Phone book sync with my TomTom occasionally works. With the Jaguar (factory fit bluetooth) it works fine. Most annoyingly with my SE HBH-DS980 it doesn't work at all.
Is this HTC's fault, WM6's fault or Sony's?????
Rich
sorry if this comes off as hi-jacking but since u mentioned bluetooth, for all of us TyTn 1 converts, how is voice command from microsoft on this? does it work throught the headset with no tweaks?
I have quite a bit of experience with the TyTN hermes tweaks to get Microsoft Voice Command to work with the Hermes but not only will the Kaiser NOT work without the tweaks - I can't get it to work with the tweaks.
I followed the exact instructions like I always have listed in the Hermes Wiki section titled Utilities and Software Tweaks (including Bluetooth Voice Command installation and the Registry changes). However after the changes I cannot initiate a Bluetooth instruction via the Bluetooth device. If I initiate the call via the handheld it works great as far as stability and sound quality.
I am going to post this as a new thread also.
Any ideas?
I have found this and a few other things that shohw mw there a quite a few differences between the Hermes with a WM6 rom and the Kaiser with it's shipped ROM.
Kaiser Bluetooth works on stock ROM Xda Stellar
I used to have it working on my i-tech mini ii but recently upgraded to Dutty's WM 6.1 just to see it failing. It was just a simple tap on the BT device and voice command worked perfectly. Im still at lost on how to resolve this and I just got Cyberon Voice Commander running on button 6 but the simple tap, i think it may need some registry tweaks.
Any ideas?
I'm having a rather odd problem using Dutty's 6.1 rom with Microsoft Voice & my bluetooth.
While it works fine when it comes to initiating itself appropriately, once the connection between VC and the bluetooth are supposed to terminate, they don't, and consequently all sounds are routed to my BT after using VC.
I'm assuming it's something to do with an incompatability between WM 6.1 and Voice Command because I didn't have this issue with Dutty's WM6-based V4 rom.
Any ideas?
I remember seeing some sort of registry tweak that could fix certain problems with VC, but I can't find the thread using the same search keywords I used before.
Still struggling with this one. Thus far the only way to get the BT to turn off is to either power down the Kaiser, the Bluetooth, or disable BT on the Kaiser.
Hi!
I've allready tried some ROMs on my BA (xplode wm6.1 and so on), but i have problems with bluetooth. I can't get my BA working with tomtom 6 and my Nokia LD-3W gps mouse. I also have problems sending stuff through bluetooth (for example contacts from my mobile phone). On wm2003 everything works fine. But I don't want the wm2003.
please help me!
try updating your bt stack to latest version. should be able to find it in the ba wiki
I've got the latest BT stack allready...
I had a similar problem with my Haicom BT GPS mouse when set up according to the instructions in the wiki.
Removing the "secure connection" to the mouse my problems with GPS went away.
As I normally don't use BT for anything else I can't comment on other bt problems.
When you install xplode rom install his all fixes cab files it will fix BT wifi contacts and beam
The xplode ROM is the one I love
(failing that I drop back to the o2 distribution 2003 ROM.
I have TomTom or CoPilot open and take/make a call via my bluetooth headset. Both programs will then stop talking to me both during and after the call. I have to reset the device to get them to talk again (even restarting the program doesn't work). Sound on the device functions properly. Is there anyone else experiencing this and know of a fix?
Maybe give us your Rom and radio for help.
Sure its garmin's wm6.1 rom (v1.2 I think) with the radio that's 1.58... (I'm at work without my phone (I work in a prison) thus cannot check. But, this was a problem with TomTom on my tilt with the standard att rom before I changed to garmin also.
Thanks,
Alan
I had installed the skype in my Diamond and works fine with my wifi connection. the problems is: my bluetooth headset (motorola H300) works fine when I make a call but not with skype (any skype sound in the bluetooth headset). Any idea will be wellcome
pruebas123 said:
I had installed the skype in my Diamond and works fine with my wifi connection. the problems is: my bluetooth headset (motorola H300) works fine when I make a call but not with skype (any skype sound in the bluetooth headset). Any idea will be wellcome
Click to expand...
Click to collapse
See my article at http://wiki.xda-developers.com/inde...t using traditional (mono) Bluetooth headsets
Sorry, the I searched forums but not took care about the wiki. Thanks
I have the same problem. So Diamond uses MS bluetooth stack? Installing that BTAudio 810 program solves the issue?
PaWs said:
I have the same problem. So Diamond uses MS bluetooth stack? Installing that BTAudio 810 program solves the issue?
Click to expand...
Click to collapse
1, yes
2, duno, Haven't checked it myself
For me, the BTAudioNav by infamous PPC hacker works perfect with my diamond!!!
BTAudio
http://www.davidmays.com/blog/?postid=6