Database Develop

No Activesync

My 8125 won't connect via activesync. Any solutions?

todd5433 said:
My 8125 won't connect via activesync. Any solutions?
Click to expand...
Click to collapse
We need more info to help you on this.
Is your cable ok ?
Which ROM do you have ?
Which active-sync version do you have ?
Is your computer noticing a connection ?
etc.

Be sure it's not a cable issue.
See my case:
I have 2 USB connections on the back side of my PC:
1 - Has a normal extension cable to reach the top of the desk where i connect my flash drives;
2 - Has an A-B extension where i usually connect my Wizard, mp3 player, Kodak, card-reader etc..
What happened today was that the cable no2 was occupied and so i decided to connect an A-B extension to the no1 extension. This second extension is from the card reader and has a 'cilinder' before reaching the end of the lead which i believe to have some resistors or other electric component. Final outcome: the Wizard was charging the battery (orange led) but active sync wasn't able to detect it
This could mean two things:
1- Two extensions make the cable too long (is it possible to be too long?)
2- The electric components of the second exrtension are messing the communication
cheers

Let me guess
You have installed WM06 Crossbow ? And you are not using Active Sync 4.5 ?

How can I use the activesync and not charge the kaiser.

Hello. How can I syncronize with activesync (cable usb) and install programs with charge the batterie of kaiser.
Thanks.

yes, you can.
Start>Settings>System>Power then click on the Advanced tab and check the "When Device is turned on, do not charge the battery when connected to the PC"

Start --> Settings --> System --> Power --> Advanced (tab) --> "If the device is turned on and connected to a PC....."
Check that option (translated from Dutch ROM, wording may be a tad bit different).

Imanoltxo said:
Hello. How can I syncronize with activesync (cable usb) and install programs with charge the batterie of kaiser.
Thanks.
Click to expand...
Click to collapse
See this thread

Thanks for your help.
Hello. Thanks. I didn't see. Now ok.
Bye.

Charging w/o Activesync

Could somebody tell me or point me to an area that will explain how i can use the USB cable to charge the phone w/o syncing with activesync?
Thanks!

Open Active Sync connection settings, and disable "allow USB-connections"

Ya, i can't install activesync at work. With my old Dell back in the day it wouldn't charge unless activesync was installed. But i just plugged in my Kaiser w/o active sync and it automatically started charging. So NM i guess!
Thanks for the response btw!

activesync start with tomtom 7

whan I start tomtom 7 I saw in task manager also activesync starting...some info about it?

same issue for me.
and each time I launch tomtom7, I have activesync and a WAP connexion is establised .... it is strange.
I have done a hard reset and installed it a new time without other applications but issue is still present.

Hi here,
I just noticed it too . Did you find a solution ?

Do you use an car charger when using TT7? I think it has something to do with connecting an USB cable to the TD

[Q]Error on my Diamonds USB slot?

Hi!
I've searched and fund some stuff similar to my problem but no solution, so I'm trying again.
The problem started when I updated to ROM v 1.93.
Whenever I connect my device to the PC (I'm running Vista) through USB connection I get the quistion on my phone if I wanna use it in Active Sync mode or as a disk. So far so good. No matter which alternative I choose i takes only a few seconds for me to get the same dialogue on my phone again and again and again and I cannot acces the phone from my PC.
My first thought was that the usb slot in the phone must be broken but I can charge the phone if I plug inte wall but not via the PC.
Is this a software prob. or something else and can this be fixed or do I have the go back to the store with the phone?
I would really appreciate some creative answers to this.

Do you have any other miniUSB cables to test with? That would be my first move.

poedgirl said:
Do you have any other miniUSB cables to test with? That would be my first move.
Click to expand...
Click to collapse
Yes, I have tested with another cable and it's the same result...

wigh said:
Yes, I have tested with another cable and it's the same result...
Click to expand...
Click to collapse
Disconnect device and delete the partnership between PC and Diamond. Try reconnecting. If no joy, delete partnership and delete Windows Mobile Adapter from Device Manager.

tnyynt said:
Disconnect device and delete the partnership between PC and Diamond. Try reconnecting. If no joy, delete partnership and delete Windows Mobile Adapter from Device Manager.
Click to expand...
Click to collapse
Tried that now and even tried it on another PC but it just won't work.