P3600 - only serial connect in bootloader - P3600 Software Upgrading

I have a SFR s300+ locked to sfr on France...
So I need to change rom...
When windows mobile run - device can synhronize and activesync enable, but when I put device in bootloader by sspl or without them device only show as SERIAL connection not usb! I`ve tried to change cable, ports other OS on my laptops and other but I can`t connect to it in bootloader mode via usb...
where a problem hide ?
please, help.

1 connect the ppc to pc with usb cable
2 put it in bootloader mode while connected
worked for me this way.

bootloader problem
i've the same problem , i've tried everything without success. In order:
- change usb cable
-change usb port on my laptop
- change personal computer, reinstalling active sync
- change settings in "settings-connections-usb to pc"
- hard reset
Syncro works well, my phone works well but i'm not able to upgrade the LASAGNA ROM 'cause when i enter in bootloader mode, it stay only in SERIAL MODE. There's a workaround to install the rom from the SD card instead of the USB cable?

Is a cable' problem.
Change the usb.
I had te same problem, after works 100%.

I've tried with another USB cable but it didn't work. with the other cable i'm able to do everything like the original HTC cable i'm actually use. Do you think i should buy another usb cable? What are the specifications of the htc cable?

ilmetallo said:
I've tried with another USB cable but it didn't work. with the other cable i'm able to do everything like the original HTC cable i'm actually use. Do you think i should buy another usb cable? What are the specifications of the htc cable?
Click to expand...
Click to collapse
I tryed with another cable, don't work. I definitely exclude a cable problem. I think there's something wrong with the miniusb connection in the device. I would try to upgrade the ROM directly from sd card but the procedure in wiki don't work.

got it fixed
your overloading the usb port most likely old computer/laptop or power issues, i have the xv6700 so i can use the cradle for power from a wall socket then plug the other cable into the usb port. works like a charm

p3600 - only serial connect in bootloader
it has to be your pc drivers if your pc/laptop is vista there is a site with driver swap for xp drivers for vista pc/laptops. had the same issue and voila mines sorted.laso check comm manager on your device as well jus to make sure as i write jus completed rom upgrade to wm6.1 from spv m700

Related

Romupdate dowsn't see my USB connection

I put my pda in bootloader mode. Serial v1.00 is what i see. I plug the USB cable in it and what i see is USB v1.00. I start romupdate.exe, but it cannot see the usb connection.
What am i doing wrong? I tried it on 2 pc's, both are not working.
Any help appreciated.
Nevermind, i forgot to kill the activesync process.
i hv dopod838 wwe , installed & run the lookiwz02a ( U & C ),
but when running romupdate, with activesync usb off, still romupdate won't recognize the usb. i also tried mtty with same result, usb not recognize.

The Mobile Can Only Enter Serial Mode

I upgraded TMobile MDA, but there's a problem. The mobile can't boot since then! But it can enter serial mode(boot loader), and I can only see these words from from LCD:
Serial
V2.07
I found many upgrade software and many ROMs for blue angel, using MaUpgradeUt_noID.exe or MaUpgradeUt.exe. But it seems that the programs can't find the mobile!
How can I do now? Is there a hardware problem? Maybe I don't find the suitable program, maybe I should find a new program because there's no OS but only a bootloader in it. If someone knows how to deal with this mobile, please tell me. Thank you very much!
Didn't work. Still hanging in boot loader mode.
I have the same problem with my HTC Blue Angel (PH20b)... Locked in Boot Loader mode following a failed ROM upgrade attempt. I tried adding the line to the ruu.conf file as suggested, but I still get the same error just after starting an upgrade attempt...
"Error 120: Country ID Error no-no-no-12-12-12"
Same as it has been for the past month or so. Anyone have any other ideas? I've tried to install just about every rom available... All with the same result every time.
Thanks,
-Mark
flypen said:
I upgraded TMobile MDA, but there's a problem. The mobile can't boot since then! But it can enter serial mode(boot loader), and I can only see these words from from LCD:
Serial
V2.07
I found many upgrade software and many ROMs for blue angel, using MaUpgradeUt_noID.exe or MaUpgradeUt.exe. But it seems that the programs can't find the mobile!
How can I do now? Is there a hardware problem? Maybe I don't find the suitable program, maybe I should find a new program because there's no OS but only a bootloader in it. If someone knows how to deal with this mobile, please tell me. Thank you very much!
Click to expand...
Click to collapse
Sounds like a PC Driver problem. When using a USB cable, the bootloader screen will switch to say USB and the PC will display that a USB device was attached. Is this occurring? if not, try another USB port.
Quick Q
MDA is Blueangel and not wizard?
rschell said:
Sounds like a PC Driver problem. When using a USB cable, the bootloader screen will switch to say USB and the PC will display that a USB device was attached. Is this occurring? if not, try another USB port.
Click to expand...
Click to collapse
Should I install a special driver in PC?
just helping
flypen said:
Should I install a special driver in PC?
Click to expand...
Click to collapse
nope, when entering in the bootloader mode, it usually indicates "serial" but when you would attach the usb cable it would change to "USB" mode without installing anything just the cable itself.
Oh, 3x! When I plug in USB cable, the text on LCD is still Serial. Maybe there's some problem with the cable.
flypen said:
Oh, 3x! When I plug in USB cable, the text on LCD is still Serial. Maybe there's some problem with the cable.
Click to expand...
Click to collapse
The bootloader screen will not change until the USB cable is plugged into the PC and the Phone. You should get a Microsoft USB device showup on the PC under Windows CE USB Sync in device manager (Win XP).
Can anyone tell me what was the solution to get the IIs into a USB mode?
Im having a same problem. Its keep saying serial and even after i plug it into the USB port it does not change to USB.
Any ideas?
thanks
This problem is solved
I changed a USB cable, then I can found "USB" showing in the screen! Everything is OK now.
The only problem is that the first USB cable doesn't work. A good new USB cable can solve this problem!
Thank you very much, rschell.

Killed my Tytn 2 ?

Hi guys, i have probably killed my beloved kaiser.
This is what i did:
- Flashed latest Hyperdragon III Rom - all worked fine here
- Sometime later i figured out that the phone was not able to connect to my PC anymore (tried different computer and cable, no change: unknown usb device)
- I then entered boot loader and tried to flash an older rom (Garmin DK 3) but it stopped at 16% and i had to enter boot loader again.
The result:
Now no pc is detecting the tytn 2 correctly (unkown usb device) on boot loader screen. I guess that the usb port on the phone is somehow damaged. Any suggestions ?
http://wiki.xda-developers.com/index.php?pagename=Kaiser_Stuck_at_bootloader
there u go
I just want to say that your phone not connecting was a simple thing.
Moved to apropos section.
tabaz said:
- Sometime later i figured out that the phone was not able to connect to my PC anymore (tried different computer and cable, no change: unknown usb device)
Click to expand...
Click to collapse
Did you try deleting your sync settings?
Delete device from sync list.
unplug/replug usb. setup device again.
Or I have also had to un & re install Active-sync.
Hope this helps
nonono .. its not that active sync is not working anymore, its that windows detects the device either as unknown device (on bootloader screen!) or does not detect it at all. I even cant select USB in mtty.exe - active sync disabled. Iam pretty much sure its an usb port issue since my tytn2 have had always problem with usb cons (did not recharge and stuff). Before that issue my pc had detected the tytn2 in bootloader screen.
tabaz said:
nonono .. its not that active sync is not working anymore, its that windows detects the device either as unknown device (on bootloader screen!) or does not detect it at all. I even cant select USB in mtty.exe - active sync disabled. Iam pretty much sure its an usb port issue since my tytn2 have had always problem with usb cons (did not recharge and stuff). Before that issue my pc had detected the tytn2 in bootloader screen.
Click to expand...
Click to collapse
Try another USB cable. I have a faulty cable at work and my phone disconnects from AS all the time. At home, no problems
Dave
i have tried several usb cable on several computer - same problem.
tabaz said:
i have tried several usb cable on several computer - same problem.
Click to expand...
Click to collapse
Oh well, it worth a shot.
Dave

USB only works in SPL. No device found when in WM

It was always working. But now when I connect it to the PC. Only battery charging, no usb device recognized (nothing will show in my computer). I have tried different PCs, all are the same.
And if I boot into Hardspl four color screen, usb can be found. So I flashed different Radios and Roms, even latest stock WM6.1 ROM. Still the USB only works in SPL but not Windows Mobile Interface.
I think it maybe a software problem. But since it is now with stock WM6.1 and Radio, what can I do further?
Thanks!
try to disable "Enable faster data synchronization" under the USB to PC settings and try again.
the USB to PC settings are usually in Start->Settings->Connections.
other than that, i can't think of much else but i'm certain someone else can come up with some more suggestions.
ASCIIker said:
try to disable "Enable faster data synchronization" under the USB to PC settings and try again.
the USB to PC settings are usually in Start->Settings->Connections.
other than that, i can't think of much else but i'm certain someone else can come up with some more suggestions.
Click to expand...
Click to collapse
Thanks! I have tried that already after searched over google and xda. But it doesn't work. No usb device show up when I connect the Kaiser. Only battery charging.
Does spl USB mode use different pins from Activesync? Forgot to say, I flashed Hardspl with force-usb.
Maybe like this, the USB port detects PC host before it activate USB function. In spl, the "force-usb" gets the USB port always activated.
changing the radio isnt going to make a blind bit of difference, although stating which rom you flashed and what windows version (PC) you are using might!
If its xp totally uninstall active sync and download the latest version from microsoft and install that
If its vista then download the latest version of WMDC and install that
also after flashing the rom, as soon as you have aligned the screen and customization has completed soft reset and when it reloads go and clear storage.
Did you have a biug storage rom installed before it failed to connect to USB?
Thats about all i can suggest till you supply more info
Thank you for those suggestion. I thought flash new roms will automatically hard reset the Kaiser. I will try to use "clear storage".
The rom I last used is http://forum.xda-developers.com/showthread.php?t=533617
Before I flashed this rom, usb worked fine.
The problem is no device shown in Windows device manager, not even unknown device. Just like nothing has been plug into the USB port. But same cable and port work with another X1
i'm having the same problem as well after flashing b16b rom
http://forum.xda-developers.com/showpost.php?p=3996365&postcount=826
anyone have the solution ? even i chg the spl and flash the stock rom my activesync still won't functioning..the usb port only able to charge the battery only
I would check your pins in the charging port and make sure you can see 5 pins on top and they are not bent

LG G6 not recognised by PC

I got my new T-Mobile LG G6 today. I am unable to connect the same to my PC (Windows 8.1),
In the phone I am able to set the USB Debugging ON before connecting to PC. But once I connect the
phone to PC through the supplied USB cable the USB Debugging becomes greyed out and the PC is
unable to recognise the phone. I have change the USB ports and tried. Any help please ?
tupuluruk said:
I got my new T-Mobile LG G6 today. I am unable to connect the same to my PC (Windows 8.1),
In the phone I am able to set the USB Debugging ON before connecting to PC. But once I connect the
phone to PC through the supplied USB cable the USB Debugging becomes greyed out and the PC is
unable to recognise the phone. I have change the USB ports and tried. Any help please ?
Click to expand...
Click to collapse
Try to either to use USB 2.0 type C cable or to update the Unified driver to 4.2.0 (add USB 3.1 support)
Install Windows 7 or 10. Install lg mobile driver. Plug in phone.
Did you install drivers?
Go to device manager and find your phone and uninstall it. Reboot. Plug in phone let driver install
Looks like only it's genuine usb 3.1 cable it's working for file transfer with PC!
ovu85 said:
Looks like only it's genuine usb 3.1 cable it's working for file transfer with PC!
Click to expand...
Click to collapse
cable and quick charge adapter of samsung is working great with my G6 T-Mobile.
For me personally the stock cable is the only one that allows me full USB functionality

Categories

Resources