The Mobile Can Only Enter Serial Mode - MDA III, XDA III, PDA2k, 9090 Software Upgrading

I upgraded TMobile MDA, but there's a problem. The mobile can't boot since then! But it can enter serial mode(boot loader), and I can only see these words from from LCD:
Serial
V2.07
I found many upgrade software and many ROMs for blue angel, using MaUpgradeUt_noID.exe or MaUpgradeUt.exe. But it seems that the programs can't find the mobile!
How can I do now? Is there a hardware problem? Maybe I don't find the suitable program, maybe I should find a new program because there's no OS but only a bootloader in it. If someone knows how to deal with this mobile, please tell me. Thank you very much!

Didn't work. Still hanging in boot loader mode.
I have the same problem with my HTC Blue Angel (PH20b)... Locked in Boot Loader mode following a failed ROM upgrade attempt. I tried adding the line to the ruu.conf file as suggested, but I still get the same error just after starting an upgrade attempt...
"Error 120: Country ID Error no-no-no-12-12-12"
Same as it has been for the past month or so. Anyone have any other ideas? I've tried to install just about every rom available... All with the same result every time.
Thanks,
-Mark

flypen said:
I upgraded TMobile MDA, but there's a problem. The mobile can't boot since then! But it can enter serial mode(boot loader), and I can only see these words from from LCD:
Serial
V2.07
I found many upgrade software and many ROMs for blue angel, using MaUpgradeUt_noID.exe or MaUpgradeUt.exe. But it seems that the programs can't find the mobile!
How can I do now? Is there a hardware problem? Maybe I don't find the suitable program, maybe I should find a new program because there's no OS but only a bootloader in it. If someone knows how to deal with this mobile, please tell me. Thank you very much!
Click to expand...
Click to collapse
Sounds like a PC Driver problem. When using a USB cable, the bootloader screen will switch to say USB and the PC will display that a USB device was attached. Is this occurring? if not, try another USB port.

Quick Q
MDA is Blueangel and not wizard?

rschell said:
Sounds like a PC Driver problem. When using a USB cable, the bootloader screen will switch to say USB and the PC will display that a USB device was attached. Is this occurring? if not, try another USB port.
Click to expand...
Click to collapse
Should I install a special driver in PC?

just helping
flypen said:
Should I install a special driver in PC?
Click to expand...
Click to collapse
nope, when entering in the bootloader mode, it usually indicates "serial" but when you would attach the usb cable it would change to "USB" mode without installing anything just the cable itself.

Oh, 3x! When I plug in USB cable, the text on LCD is still Serial. Maybe there's some problem with the cable.

flypen said:
Oh, 3x! When I plug in USB cable, the text on LCD is still Serial. Maybe there's some problem with the cable.
Click to expand...
Click to collapse
The bootloader screen will not change until the USB cable is plugged into the PC and the Phone. You should get a Microsoft USB device showup on the PC under Windows CE USB Sync in device manager (Win XP).

Can anyone tell me what was the solution to get the IIs into a USB mode?
Im having a same problem. Its keep saying serial and even after i plug it into the USB port it does not change to USB.
Any ideas?
thanks

This problem is solved
I changed a USB cable, then I can found "USB" showing in the screen! Everything is OK now.
The only problem is that the first USB cable doesn't work. A good new USB cable can solve this problem!
Thank you very much, rschell.

Related

P3600 - only serial connect in bootloader

I have a SFR s300+ locked to sfr on France...
So I need to change rom...
When windows mobile run - device can synhronize and activesync enable, but when I put device in bootloader by sspl or without them device only show as SERIAL connection not usb! I`ve tried to change cable, ports other OS on my laptops and other but I can`t connect to it in bootloader mode via usb...
where a problem hide ?
please, help.
1 connect the ppc to pc with usb cable
2 put it in bootloader mode while connected
worked for me this way.
bootloader problem
i've the same problem , i've tried everything without success. In order:
- change usb cable
-change usb port on my laptop
- change personal computer, reinstalling active sync
- change settings in "settings-connections-usb to pc"
- hard reset
Syncro works well, my phone works well but i'm not able to upgrade the LASAGNA ROM 'cause when i enter in bootloader mode, it stay only in SERIAL MODE. There's a workaround to install the rom from the SD card instead of the USB cable?
Is a cable' problem.
Change the usb.
I had te same problem, after works 100%.
I've tried with another USB cable but it didn't work. with the other cable i'm able to do everything like the original HTC cable i'm actually use. Do you think i should buy another usb cable? What are the specifications of the htc cable?
ilmetallo said:
I've tried with another USB cable but it didn't work. with the other cable i'm able to do everything like the original HTC cable i'm actually use. Do you think i should buy another usb cable? What are the specifications of the htc cable?
Click to expand...
Click to collapse
I tryed with another cable, don't work. I definitely exclude a cable problem. I think there's something wrong with the miniusb connection in the device. I would try to upgrade the ROM directly from sd card but the procedure in wiki don't work.
got it fixed
your overloading the usb port most likely old computer/laptop or power issues, i have the xv6700 so i can use the cradle for power from a wall socket then plug the other cable into the usb port. works like a charm
p3600 - only serial connect in bootloader
it has to be your pc drivers if your pc/laptop is vista there is a site with driver swap for xp drivers for vista pc/laptops. had the same issue and voila mines sorted.laso check comm manager on your device as well jus to make sure as i write jus completed rom upgrade to wm6.1 from spv m700

USB cables

Hi to all,
i wanted to flash my radio rom to 1.50 but each time i put pda to boot mode it is always writen Serial not USB. I tried to flash it from SD card but it does flashing but when i reboot it is still old radio rom. Then i changed usb cabel and in boot mode it gives me USB connection.
I bought new one (1.8m long and tried it, again it gives me Serial. Tried several cables same story. Is there difference in usb cables?
So if you can not do hardspl, if it gives you error 260 and no usb in white part of boot screen just try other usb cable.
Igor
komple said:
Hi to all,
i wanted to flash my radio rom to 1.50 but each time i put pda to boot mode it is always writen Serial not USB. I tried to flash it from SD card but it does flashing but when i reboot it is still old radio rom. Then i changed usb cabel and in boot mode it gives me USB connection.
I bought new one (1.8m long and tried it, again it gives me Serial. Tried several cables same story. Is there difference in usb cables?
So if you can not do hardspl, if it gives you error 260 and no usb in white part of boot screen just try other usb cable.
Igor
Click to expand...
Click to collapse
Read the guides my friend!
tnyynt said:
Read the guides my friend!
Click to expand...
Click to collapse
I read guides.There is nothing ther about usb cable. My point was that it works with some cables and with some it doesn't.
komple said:
I read guides.There is nothing ther about usb cable. My point was that it works with some cables and with some it doesn't.
Click to expand...
Click to collapse
You don't happen to use Vista, do you? In case you do, read here!
...and I've told you to read the guides because flashing from the SD Card works in every case, if you make the procedure right (have HardSPL installed and you do it the way described here.)
tnyynt said:
You don't happen to use Vista, do you? In case you do, read here!
...and I've told you to read the guides because flashing from the SD Card works in every case, if you make the procedure right (have HardSPL installed and you do it the way described here.)
Click to expand...
Click to collapse
this is not my first time to flash pda and i am not using vista.
It was my experience that wile i was in bootstarp screen (tricolor screen) while changeing several usb cables, with 3-4 of them it gave me only Serial connection but whith only with one of them it gave me USB connection on white screen and i could flash radio rom. Strange thing is thaht i can do synchromization with all of them. I tried it also on other computer with XP.
Maybe is something with my pda.
Oh yes i ahave hardspl 1.30.
komple said:
this is not my first time to flash pda and i am not using vista.
It was my experience that wile i was in bootstarp screen (tricolor screen) while changeing several usb cables, with 3-4 of them it gave me only Serial connection but whith only with one of them it gave me USB connection on white screen and i could flash radio rom. Strange thing is thaht i can do synchromization with all of them. I tried it also on other computer with XP.
Maybe is something with my pda.
Oh yes i ahave hardspl 1.30.
Click to expand...
Click to collapse
OliPro 1.30 has been reported with some issues, maybe that's why you can not flash with SD Card. I'd say to install Des' Crash Proof SPL but then you can not flash because of USB issue.
I have similar problem, need to first put the pda in booloader mode.
After that my usb connection is somehow stalled and the pda shows a serial connection.
Then i either have to reboot the computer or use another usb bus, to get the pda connected with usb.. Has nothing to do with the cables, but the fact windows is winblows.... (xp in my case).
Perhaps this is another issue tho..
Br Fredrik
I can do flash with one cable it is working fine.
Why do you recommend Des' Crash Proof SPL. What is difference from hardspl? Except maybe less issues ?
this made my day and allowed me to flash in vista (twice) without breaking a sweat!
http://forum.xda-developers.com/showthread.php?t=331675

Killed my Tytn 2 ?

Hi guys, i have probably killed my beloved kaiser.
This is what i did:
- Flashed latest Hyperdragon III Rom - all worked fine here
- Sometime later i figured out that the phone was not able to connect to my PC anymore (tried different computer and cable, no change: unknown usb device)
- I then entered boot loader and tried to flash an older rom (Garmin DK 3) but it stopped at 16% and i had to enter boot loader again.
The result:
Now no pc is detecting the tytn 2 correctly (unkown usb device) on boot loader screen. I guess that the usb port on the phone is somehow damaged. Any suggestions ?
http://wiki.xda-developers.com/index.php?pagename=Kaiser_Stuck_at_bootloader
there u go
I just want to say that your phone not connecting was a simple thing.
Moved to apropos section.
tabaz said:
- Sometime later i figured out that the phone was not able to connect to my PC anymore (tried different computer and cable, no change: unknown usb device)
Click to expand...
Click to collapse
Did you try deleting your sync settings?
Delete device from sync list.
unplug/replug usb. setup device again.
Or I have also had to un & re install Active-sync.
Hope this helps
nonono .. its not that active sync is not working anymore, its that windows detects the device either as unknown device (on bootloader screen!) or does not detect it at all. I even cant select USB in mtty.exe - active sync disabled. Iam pretty much sure its an usb port issue since my tytn2 have had always problem with usb cons (did not recharge and stuff). Before that issue my pc had detected the tytn2 in bootloader screen.
tabaz said:
nonono .. its not that active sync is not working anymore, its that windows detects the device either as unknown device (on bootloader screen!) or does not detect it at all. I even cant select USB in mtty.exe - active sync disabled. Iam pretty much sure its an usb port issue since my tytn2 have had always problem with usb cons (did not recharge and stuff). Before that issue my pc had detected the tytn2 in bootloader screen.
Click to expand...
Click to collapse
Try another USB cable. I have a faulty cable at work and my phone disconnects from AS all the time. At home, no problems
Dave
i have tried several usb cable on several computer - same problem.
tabaz said:
i have tried several usb cable on several computer - same problem.
Click to expand...
Click to collapse
Oh well, it worth a shot.
Dave

Big Problem - Is my Kaiser dead??

Happy new year everyone!
I have a big problem with my kaiser, maybe is 2011 a bad year for me ..
Well, I flashed for the third time the modded kernel of DnbTommy (including a RADIO, SPL, etc..).
Just after the flash, my Kaiser won't boot!
Just a black screen, and green LED. (can't hard reset, flash, or anything ..)
I made searchs on XDA and more, and I heard about MTTY solution..
But when I plug in my Kaiser in the USB cradle, it recognizes an unknown "Data Interface".
And MTTY does not recognize the USB port.. I tried on a Windows 7 (x64) computer, and a Windows XP (x32) laptop, with the same results.
Thanks for your help!
Try removing the battery for roughly 30 seconds then re-install
I already did it, even changing battery, but no results
Go in flash mode (camera button and reset) and flash another nbh.
Hi L1q1d,
Unfortunately, I can't go in flash mode, bootloader mode, or anything..
My screen stays black, and I can't flash!
Is the battery charged?
Of course it is !
I really need help please, elsewhere, my Kaiser will be lost..
Thanks in advance!
Have a search for the Diagnostic drivers you might be able to connect with mtty with them?
If you mean the drivers folder named
"x64 AS Drivers Win 7 Tested & Working" ,
including 2 files : wceusbsh.sys and wceusbshx64.inf
then, it does not..
No i mean the motoQ diag drivers these work with win 7 not sure about x64 ?
meknb said:
No i mean the motoQ diag drivers these work with win 7 not sure about x64 ?
Click to expand...
Click to collapse
Okay I will try it, then! Thanks!
Do I have to install them when it asks for "Data Interface" driver?
Yes just unzip them first.
Well, I tried on a Windows XP 32 Bits laptop.
I plugged in my Kaiser with USB cable, installed MotoQ Drivers when it asked for "Data Interface" drivers,
But when I run mtty.exe, it shows me 3 more "COM" ports.. But no USB!
If I plug out my Kaiser, 3 ports less appears, then..
What could I do now?
Thanks!
I haven't a kaiser but id suggest looking through the frankenkaiser threads, you can connect mtty via a com port check device manager to see what port to connect with.In device manager look through the serial ports.
Try setboot 0 then cego via mtty.
meknb said:
I haven't a kaiser but id suggest looking through the frankenkaiser threads, you can connect mtty via a com port check device manager to see what port to connect with.In device manager look through the serial ports.
Click to expand...
Click to collapse
When I connect the Kaiser, 3 ports appears in device manager / in MTTY :
- COM3 (cant find its name in device manager)
- COM4 : "Qualcomm Diagnostics Interface 6000"
- COM5 : "Qualcomm NMEA Device"
If I connect to COM3 or COM5, MTTY seems to be blocked..
But if I select COM4, MTTY doesn't crash, but i'm unable to type a command, because it says "Invalid command" to everything I write..
Really, thanks for ur help!!
Yes com4 is the one you need to connect mtty with but id read through the frankenkaiser and related threads,you may find more help there. Good luck
I found here the thread named "Frankenkaiser SPL Loader" :
http://forum.xda-developers.com/showthread.php?t=394584
I tried the step 4, but nothing happends.
I cannot connect to MTTY with the Kaiser, that's the real problem..
Maybe there's another way than MTTY?
Over two years of flashing, it's the first problem that I get with the Kaiser..
Thanks! I really hope to find a solution to make my kaiser alive..
One thing to check is disable Allow usb connections in windows mobile device centre.
Another thing is try different versions of mtty i use mtty_0513_Test or you can try putty does the same thing as mtty.
I'm sure you'll get your kaiser back to life again.
I had stopped rapimgr.exe, but after you told me, I unchecked the "usb connection" box in ActiveSync..
Tried with MTTY 1.42, 0.01, 0513_Test, but nothing happends..
Same with PuTTY...
I think it's a communication problem!?
I would donate you, if you find the solution..

One M7 no connect to usb only charge

Hi i have HTC One M7 801n and cant connect to PC, i try whith other cables, other computers, different usb ports and drivers, nothing works, the micro usb conector seems to be ok, no message apears in the phone and only charge, fastboot says "fastboot ac" when conect to pc. i have the bootloader unlocked but i whant at least root the phone, any ideas pls ?
Or some way to root the phone whitout connect to pc ? Adb over WiFi ? Please help !!!
PITA22 said:
Or some way to root the phone whitout connect to pc ? Adb over WiFi ? Please help !!!
Click to expand...
Click to collapse
Please ! any one ?
PITA22 said:
Please ! any one ?
Click to expand...
Click to collapse
unlocking the bootloader requires a PC how did you do it ?
clsA said:
unlocking the bootloader requires a PC how did you do it ?
Click to expand...
Click to collapse
I did before, when the usb worked
PITA22 said:
I did before, when the usb worked
Click to expand...
Click to collapse
does device manager see your phone
have you tried different usb ports and cables.
have you installed the HTC drivers
do you have usb debugging enabled in developer options ?
clsA said:
does device manager see your phone
have you tried different usb ports and cables.
have you installed the HTC drivers
do you have usb debugging enabled in developer options ?
Click to expand...
Click to collapse
device manager see it "unknow device"
different ports cables and PCs not work.
usb debugging or not its the same, not recognize and "unknow device"
PITA22 said:
device manager see it "unknow device"
different ports cables and PCs not work.
usb debugging or not its the same, not recognize and "unknow device"
Click to expand...
Click to collapse
Reboot your phone and computer then try to connect it again. If the same issue, then look at this post and see if it will help. I have also uninstalled the drivers, rebooted the computer and then install the drivers again but not HTC Sync Mgr.
majmoz said:
Reboot your phone and computer then try to connect it again. If the same issue, then look at this post and see if it will help. I have also uninstalled the drivers, rebooted the computer and then install the drivers again but not HTC Sync Mgr.
Click to expand...
Click to collapse
nothing works like i said before already try in other computers win 7, winxp etc, always "unknow device" already try whith the las versions of HTC Drivers, in win7 and other computer whith xp, always apears like unknow device in device manager, like i said before in fasboot mode says only "fastboot ac".
Before stop working in one chance, connects and disconnects constantly without me touch the cable and and suddenly stop working
PITA22 said:
nothing works like i said before already try in other computers win 7, winxp etc, always "unknow device" already try whith the las versions of HTC Drivers, in win7 and other computer whith xp, always apears like unknow device in device manager, like i said before in fasboot mode says only "fastboot ac".
Before stop working in one chance, connects and disconnects constantly without me touch the cable and and suddenly stop working
Click to expand...
Click to collapse
If you have not done it already, try wiggling the mini-usb cable to see if it improves anything. Is the phone charging? It might be a hardware problem, I have read in some other post that it is the motherboard. Sorry, I can not think of anything else.
majmoz said:
If you have not done it already, try wiggling the mini-usb cable to see if it improves anything. Is the phone charging? It might be a hardware problem, I have read in some other post that it is the motherboard. Sorry, I can not think of anything else.
Click to expand...
Click to collapse
Yes i try to move the cable in the side of the micro usb, and 5 Or 6 diferents cables, and yes, the phone only charge.
Its very strange because I bought the phone used and only works one day and the second day lost the connection to pc when in try to unlock the bootloader, the first time no connected and suddenly work, I can only unlock the bootloader and stop working.
PITA22 said:
Yes i try to move the cable in the side of the micro usb, and 5 Or 6 diferents cables, and yes, the phone only charge.
Its very strange because I bought the phone used and only works one day and the second day lost the connection to pc when in try to unlock the bootloader, the first time no connected and suddenly work, I can only unlock the bootloader and stop working.
Click to expand...
Click to collapse
Try to clean the phone's contacts with a little rubbing alcohol and/or compressed air. There maybe lint or dirt on the contacts preventing a good connection.
maybe this shud work for u , it worked for me
http://canvas2update.blogspot.nl/2014/11/not-connecting-as-usb-storage-only.html
go to your battery manager, disable fast reboot. then turn off the phone and start it back up. It worked for me
punit_pandya said:
http://canvas2update.blogspot.nl/2014/11/not-connecting-as-usb-storage-only.html
Click to expand...
Click to collapse
Unfortunately that link does not work anymore. What was on it?
Asking because I got an m7 here where USB works just fine and reliably in both fastboot and recovery. But when the system (any ROM, tried more than 10 now), there's only charging. No MTP, no nothing.
Laptop's `dmesg` says:
Code:
[150266.816544] usb 2-1.5: new high-speed USB device number 16 using ehci-pci
[150266.935189] usb 2-1.5: New USB device found, idVendor=0bb4, idProduct=0c02
[150266.935193] usb 2-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[150266.935195] usb 2-1.5: Product: Android
[150266.935196] usb 2-1.5: Manufacturer: HTC
[150266.935197] usb 2-1.5: SerialNumber: XXXXXXXXXXXX
(1-2 seconds...)
Code:
[150359.023745] usb 2-1.5: USB disconnect, device number 16

Categories

Resources