Hi to all,
i wanted to flash my radio rom to 1.50 but each time i put pda to boot mode it is always writen Serial not USB. I tried to flash it from SD card but it does flashing but when i reboot it is still old radio rom. Then i changed usb cabel and in boot mode it gives me USB connection.
I bought new one (1.8m long and tried it, again it gives me Serial. Tried several cables same story. Is there difference in usb cables?
So if you can not do hardspl, if it gives you error 260 and no usb in white part of boot screen just try other usb cable.
Igor
komple said:
Hi to all,
i wanted to flash my radio rom to 1.50 but each time i put pda to boot mode it is always writen Serial not USB. I tried to flash it from SD card but it does flashing but when i reboot it is still old radio rom. Then i changed usb cabel and in boot mode it gives me USB connection.
I bought new one (1.8m long and tried it, again it gives me Serial. Tried several cables same story. Is there difference in usb cables?
So if you can not do hardspl, if it gives you error 260 and no usb in white part of boot screen just try other usb cable.
Igor
Click to expand...
Click to collapse
Read the guides my friend!
tnyynt said:
Read the guides my friend!
Click to expand...
Click to collapse
I read guides.There is nothing ther about usb cable. My point was that it works with some cables and with some it doesn't.
komple said:
I read guides.There is nothing ther about usb cable. My point was that it works with some cables and with some it doesn't.
Click to expand...
Click to collapse
You don't happen to use Vista, do you? In case you do, read here!
...and I've told you to read the guides because flashing from the SD Card works in every case, if you make the procedure right (have HardSPL installed and you do it the way described here.)
tnyynt said:
You don't happen to use Vista, do you? In case you do, read here!
...and I've told you to read the guides because flashing from the SD Card works in every case, if you make the procedure right (have HardSPL installed and you do it the way described here.)
Click to expand...
Click to collapse
this is not my first time to flash pda and i am not using vista.
It was my experience that wile i was in bootstarp screen (tricolor screen) while changeing several usb cables, with 3-4 of them it gave me only Serial connection but whith only with one of them it gave me USB connection on white screen and i could flash radio rom. Strange thing is thaht i can do synchromization with all of them. I tried it also on other computer with XP.
Maybe is something with my pda.
Oh yes i ahave hardspl 1.30.
komple said:
this is not my first time to flash pda and i am not using vista.
It was my experience that wile i was in bootstarp screen (tricolor screen) while changeing several usb cables, with 3-4 of them it gave me only Serial connection but whith only with one of them it gave me USB connection on white screen and i could flash radio rom. Strange thing is thaht i can do synchromization with all of them. I tried it also on other computer with XP.
Maybe is something with my pda.
Oh yes i ahave hardspl 1.30.
Click to expand...
Click to collapse
OliPro 1.30 has been reported with some issues, maybe that's why you can not flash with SD Card. I'd say to install Des' Crash Proof SPL but then you can not flash because of USB issue.
I have similar problem, need to first put the pda in booloader mode.
After that my usb connection is somehow stalled and the pda shows a serial connection.
Then i either have to reboot the computer or use another usb bus, to get the pda connected with usb.. Has nothing to do with the cables, but the fact windows is winblows.... (xp in my case).
Perhaps this is another issue tho..
Br Fredrik
I can do flash with one cable it is working fine.
Why do you recommend Des' Crash Proof SPL. What is difference from hardspl? Except maybe less issues ?
this made my day and allowed me to flash in vista (twice) without breaking a sweat!
http://forum.xda-developers.com/showthread.php?t=331675
Related
I upgraded TMobile MDA, but there's a problem. The mobile can't boot since then! But it can enter serial mode(boot loader), and I can only see these words from from LCD:
Serial
V2.07
I found many upgrade software and many ROMs for blue angel, using MaUpgradeUt_noID.exe or MaUpgradeUt.exe. But it seems that the programs can't find the mobile!
How can I do now? Is there a hardware problem? Maybe I don't find the suitable program, maybe I should find a new program because there's no OS but only a bootloader in it. If someone knows how to deal with this mobile, please tell me. Thank you very much!
Didn't work. Still hanging in boot loader mode.
I have the same problem with my HTC Blue Angel (PH20b)... Locked in Boot Loader mode following a failed ROM upgrade attempt. I tried adding the line to the ruu.conf file as suggested, but I still get the same error just after starting an upgrade attempt...
"Error 120: Country ID Error no-no-no-12-12-12"
Same as it has been for the past month or so. Anyone have any other ideas? I've tried to install just about every rom available... All with the same result every time.
Thanks,
-Mark
flypen said:
I upgraded TMobile MDA, but there's a problem. The mobile can't boot since then! But it can enter serial mode(boot loader), and I can only see these words from from LCD:
Serial
V2.07
I found many upgrade software and many ROMs for blue angel, using MaUpgradeUt_noID.exe or MaUpgradeUt.exe. But it seems that the programs can't find the mobile!
How can I do now? Is there a hardware problem? Maybe I don't find the suitable program, maybe I should find a new program because there's no OS but only a bootloader in it. If someone knows how to deal with this mobile, please tell me. Thank you very much!
Click to expand...
Click to collapse
Sounds like a PC Driver problem. When using a USB cable, the bootloader screen will switch to say USB and the PC will display that a USB device was attached. Is this occurring? if not, try another USB port.
Quick Q
MDA is Blueangel and not wizard?
rschell said:
Sounds like a PC Driver problem. When using a USB cable, the bootloader screen will switch to say USB and the PC will display that a USB device was attached. Is this occurring? if not, try another USB port.
Click to expand...
Click to collapse
Should I install a special driver in PC?
just helping
flypen said:
Should I install a special driver in PC?
Click to expand...
Click to collapse
nope, when entering in the bootloader mode, it usually indicates "serial" but when you would attach the usb cable it would change to "USB" mode without installing anything just the cable itself.
Oh, 3x! When I plug in USB cable, the text on LCD is still Serial. Maybe there's some problem with the cable.
flypen said:
Oh, 3x! When I plug in USB cable, the text on LCD is still Serial. Maybe there's some problem with the cable.
Click to expand...
Click to collapse
The bootloader screen will not change until the USB cable is plugged into the PC and the Phone. You should get a Microsoft USB device showup on the PC under Windows CE USB Sync in device manager (Win XP).
Can anyone tell me what was the solution to get the IIs into a USB mode?
Im having a same problem. Its keep saying serial and even after i plug it into the USB port it does not change to USB.
Any ideas?
thanks
This problem is solved
I changed a USB cable, then I can found "USB" showing in the screen! Everything is OK now.
The only problem is that the first USB cable doesn't work. A good new USB cable can solve this problem!
Thank you very much, rschell.
I flashed a new rom from the internal storage and apparently there's something wrong with it because the phone just hangs after the initial screen with the radio version and rom version!! Is there a way where I can get into the internal storage to put in a new rom? As far as I'm concern, bootloader still works (the rainbow screen) but I don't know what ot do after that...I've done many hard-resets but to no avail.
Please help!
if your bootloader works, yo can use your USB cable and computer to flash a new rom !
Hold volume down and hit the reset button. It will put you in the tricolor bootloader screen. In the white it says serial. Connect it to your usb cord. It should now say usb. Now flash the STOCK rom. Then try flashing the ROM you want.
stupid me, i formatted teh NAND before I posted this thread! Now when i plug in the USB cord, it still says "Serial" and my computer is not able to connect to it. Is there any other way???
See what happens if you now take out the SIM Card and do another hard reset.
It still says "serial"!! Are these my only options? Are there no other way?
That sounds bad. YOur Dimond is not picking up the connection to the PC via the USB cable. Can you try using a different cable also check the pins on the female USB are not bent as i've seen that happen to someone else on this forum.
EDIT: If you have one, try using another USB cable.
I try on another computer and miraculously it picked up the USB drive!! I then ran the RUU and got a working rom in there
Thank you for your help!
For some odd reason I can no longer get the the "serial" status to change to "usb". It charges but does not connect to activesync. I flashed many many times so I am not a noob at this but I might be making a noob mistake.
What I am using: SPL 1.54 (I use USPL 2.5). I am currently using Miri's v23 manilla 2.5. I am using the same pc (xp) and cables to flash.
What I've tried:
- used 3 different pc's and the original pc
- 4 different usb cables
- ticking/unticking the "enable faster data syncing" box in settings>connections>usb to pc
-ticking/unticking "allow usb connections" in activesync
-if I leave the cable in AND THEN put the phone in bootloader mode, the status is blank. When I remove the cable, it returns to "serial"
When the phone is on, it just doesn't seem to react (vista and xp)to the cable being plugged in. The led just shows that it's charging.
I pulled an all-nighter and I'm stumped.
Maybe you need to update the USB drivers. Same thing happened to me but it worked after updating the USB drivers as per this link.
http://forum.xda-developers.com/showthread.php?t=524619
I forgot the most important part-
Since the pc does not recognize that there's something plugged in, I cannot select the "HTC USB Sync" under device manager and proceed with updating the drivers. I don't think I need to but at this point I'm trying everything.
Unless there's another way of updating drivers without the phone showing up on the device manager...
Updated the usb drivers by plugging in an old htc device. The pc was able to recognize the other htc device and was able to switch from serial to usb.
But after the update, there was no improvement for the blackstone status.
Anyone? The phone still doesn't recognize the usb cable whether the phone is on or in bootloader, it just charges.
Any help is appreciated!
supadupa111 said:
Anyone? The phone still doesn't recognize the usb cable whether the phone is on or in bootloader, it just charges.
Any help is appreciated!
Click to expand...
Click to collapse
Seems something wrong with your device. Try to hard reset and do it again?
Or if you still cant connect to usb. there is another way to upgrade without connecting to pc. After upgrade to new ROM, try it again whether it can connect to pc or not? Here is some tips for you.
Connect your SD card to PC through microSD card. Copy all files from your SDcard to new folder in your PC. Then, right click on the microSDcard disk-->full Format by FAT32 (this step is very important).
After formatting SDcard, copy back all files to SDcard . Rename .nbh to BLACIMG.nbh (for Blacktone) and copy it to SDcard.
Insert your SDcard back to Touch HD. Turn off your device by Power button.
Go to Boot loader mode. Push and hold Vol. Down + press Power button.
After that your device with have a white screen with text " Press to power button for continue upgrade" press power button and it will start upgrade Rom.
You can check this video for more practical actions on youtube.(this video for HTC diamond2 but it's almost the same with Blacktone just different in rename step)
Hope it helps and cheer
Thanks for the tips =)
I've did a hard reset twice and still no luck.
I've tried to flash through SD but since I use USPL, it just hangs when I try.
If I have SPL 1.54.0000, is there something that can be flash through the SD without USPL?
supadupa111 said:
Thanks for the tips =)
I've did a hard reset twice and still no luck.
I've tried to flash through SD but since I use USPL, it just hangs when I try.
If I have SPL 1.54.0000, is there something that can be flash through the SD without USPL?
Click to expand...
Click to collapse
I have not tried this. I am on HSPL 1.56olinex but you can try my suggestion cause I think it's the only one you can choose now. I never ever use USPL. I think you can do it step by step and carefully.
Regard
It was always working. But now when I connect it to the PC. Only battery charging, no usb device recognized (nothing will show in my computer). I have tried different PCs, all are the same.
And if I boot into Hardspl four color screen, usb can be found. So I flashed different Radios and Roms, even latest stock WM6.1 ROM. Still the USB only works in SPL but not Windows Mobile Interface.
I think it maybe a software problem. But since it is now with stock WM6.1 and Radio, what can I do further?
Thanks!
try to disable "Enable faster data synchronization" under the USB to PC settings and try again.
the USB to PC settings are usually in Start->Settings->Connections.
other than that, i can't think of much else but i'm certain someone else can come up with some more suggestions.
ASCIIker said:
try to disable "Enable faster data synchronization" under the USB to PC settings and try again.
the USB to PC settings are usually in Start->Settings->Connections.
other than that, i can't think of much else but i'm certain someone else can come up with some more suggestions.
Click to expand...
Click to collapse
Thanks! I have tried that already after searched over google and xda. But it doesn't work. No usb device show up when I connect the Kaiser. Only battery charging.
Does spl USB mode use different pins from Activesync? Forgot to say, I flashed Hardspl with force-usb.
Maybe like this, the USB port detects PC host before it activate USB function. In spl, the "force-usb" gets the USB port always activated.
changing the radio isnt going to make a blind bit of difference, although stating which rom you flashed and what windows version (PC) you are using might!
If its xp totally uninstall active sync and download the latest version from microsoft and install that
If its vista then download the latest version of WMDC and install that
also after flashing the rom, as soon as you have aligned the screen and customization has completed soft reset and when it reloads go and clear storage.
Did you have a biug storage rom installed before it failed to connect to USB?
Thats about all i can suggest till you supply more info
Thank you for those suggestion. I thought flash new roms will automatically hard reset the Kaiser. I will try to use "clear storage".
The rom I last used is http://forum.xda-developers.com/showthread.php?t=533617
Before I flashed this rom, usb worked fine.
The problem is no device shown in Windows device manager, not even unknown device. Just like nothing has been plug into the USB port. But same cable and port work with another X1
i'm having the same problem as well after flashing b16b rom
http://forum.xda-developers.com/showpost.php?p=3996365&postcount=826
anyone have the solution ? even i chg the spl and flash the stock rom my activesync still won't functioning..the usb port only able to charge the battery only
I would check your pins in the charging port and make sure you can see 5 pins on top and they are not bent
Hi, flashed many many times but today when trying to flash the latest NRG ROM when I go into bootloader I am getting problems.
First of all when I go into bootloader it quickly flashes a message saying no image file or something.
Then HSPL 1.56 Olinex it doesnt show USB when I connect via USB just sticks at serial.
When connected to PC the PC just says USB device not recognized.
So I am unable to flash, I am at a loss to what to do???
I have tried different PCs, different cables, all have the same problem.
The phone boots into ROM OK and works fine, and then when I connect via USB it activesyncs fine. I really dont understand this, can anyone help?? PLeeaase as I want the new ROMs