Database Develop

How to connect XDA IIi to broadband through WiFi connection?

I have BELKIN broadband router (Irish Eircom broadband). Is it possible to connect XDA IIi (alpine) to this router through WiFi connection??? If Yes - Help me!

Yes it is. If the router is on the default settings you just need to touch the antrenna symbol at the bottom of the Today screen, then the green square at the bottom right, then the WLAN box and turn on WLAN.

Does anyone have a guide on how to setup a secure connection between PC & Phone on WI-FI?
It's baffling the heck out of me!

symondavis said:
Does anyone have a guide on how to setup a secure connection between PC & Phone on WI-FI?
It's baffling the heck out of me!
Click to expand...
Click to collapse
Depends on the router, what ya got?

I dont have a router, I have a WI-FI PCI card and my router is conected via ethernet

So you are trying to set up an ad-hoc connection.
You need to set your wireless on both the computer and the PDA to ad-hoc.
To do this on the PC depends on your operating system and device. Set up your wireless connection on the PC first making sure it is set up as an ad-hoc network.
On your XDAIIi Start>Settings>Connections Tab>Network Cards
You should see the network you have set up on the PC, make sure the ad-hoc box is ticked and connect to it.
You may have to set the TCP/IP settings manually. If you have a problem with doing that post up what you have done and how far you have got.

Yes, I'v got a connection! But NetFront_v3.2 says "Cannot read page." So, i can not surf Internet.

krayvid said:
Yes, I'v got a connection! But NetFront_v3.2 says "Cannot read page." So, i can not surf Internet.
Click to expand...
Click to collapse
Do you have the DHCP server turned on on the router?

Yes1 DHCP server IS turned on on the router.

OK, when you are connected and you click on the Wi-Fi icon on the bottom of the screen, does the network address match that of the router or has it set a default one?

Internet Connection Sharing
Depeding on your OS (is it windows/linux etc.) you'll nmeed to set up some form of proxy server or other packet forwarding to persuade the machine to accept packets on the WiFi card and to forward them to the Internet.
If you are using XP (or from memory 2K) you can switch on Internet connection sharing, follow the wizard and then browse to your hearts content.
Dave

Hi,
I also have a laptop with build-in Wifi and a qtek 2020i. I've shared the lan connection on the laptop and created a wirelles network. The laptop and qtek 2020i see each other but i can't surf on the qtek. i have windows XP.
The ip address on the qtek is fixed by default and is supposed to be 192. etc i read somewhere...
I use a modem/routeur (thomson 530) on which the laptop is connected (lan).
Could you please explain me how should i setup or manuallay choose the ip on my qtek?
Many thanks
john

Hey there
I also have a Qtek 2020i and an access point USR9106.could you plz tell me how you managed to connect to your laptop ? Plz give me instractions so i can do it myself.Thanks

Re: Hey there
nkonte said:
I also have a Qtek 2020i and an access point USR9106.could you plz tell me how you managed to connect to your laptop ? Plz give me instractions so i can do it myself.Thanks
Click to expand...
Click to collapse
I have O2 XDA 2i. I changed RADIO. Was 1.00.00 now 1.03.00. No problem with connection straight to Wi-Fi router!!!

Re: Hey there
krayvid said:
I have O2 XDA 2i. I changed RADIO. Was 1.00.00 now 1.03.00. No problem with connection straight to Wi-Fi router!!!
Click to expand...
Click to collapse
perhaps i'll give that a try, it might work for me, i hope it does as i'm not having much luck

Hi Guys,
This is starting to get confused - there are two types of connection being set up here: -
Firstly a cabled connection between the PC and the router with a wireless card in the PC. in this instance you need to forward the packets from the wireless card to the ethernet card and then onto the router.
In this case, if you are using Windows 2K or XP use the Internet connection sharing wizard, this will then enable packet forwarding on your PC, with a "DHCP server" (not fully functional) on the wireless card, when you establish the Ad Hoc (set exactly the same SSID on both cards - remember it's case sensitive and that should be all you need for Ad-Hoc) wireless connection between the 2020i and the PC you should then find that you are assigned an IP address (192.168.0.x is the default from memory). You should then have the IP address of the Wireless Interface Card on the PC set as your default gateway and DNS server - you need each of these entries in order to able to connect to the Internet.
If you want to secure this connection, you can use WEP (40 bit or 128 bit Same Key same position on both SSID configs), though remember that if a sniffer collects about 300K packets, it is possible to use AirCrack to regain the wep key - paranoid but true.
If you have a wireless gateway, this should (in all probability) already have a DHCP service up and running on it (it's probably giving your PC all of the IP settings it needs) so all you should need is to establish a connection between these two devices. Switch wireless on on the 2020 and you should be prompted with a message box saying Your_SSID connects you to and offer you work and Internet, select Internet if there is a WEP key or other form of encryption enabled you will be prompted for a key. In theory you will have set all of this up on the router in the first place so probably have some idea of what you are doing.
Hope this helps, if not feel free to throw abuse.
Kind Regards
Dave

try this link:
http://www.mtekk.com.au/browse/page1090.html
I tried it last night and it got it working in about 5 minutes!! was well pleased . I'm using the infrastructure mode, got a XDAIIi and a D-Link G604T. I dont have any authentication setup, the only thing I use is the MAC based access list, so I had to add the XDA MAC into the router access list and for the rest I followed what the above link said.
Tip: make sure you do a reset for the settings to take effect, did'nt realise thats why it took me five minutes!

hiya... sorry to bug anyone about this... but i have a problem logging on wifi connection on my Xda IIi...
using a dell TrueMobile 2300 wireless router...
(( i got a stinking feeling i might not able to do this.. cos been trying the last 4 hours and i just recalled whenever a com wants to link up with this router.. that com have to go thru it's Cd to Authz it first.. . ))
Any help would be greatly appreciated!

WPA WiFi connection
The only secure WiFi connection I can use on my XDA IIi is via WEP. For some unknown reason I cannot connect using WPA.
Any ideas...

SlingPlayer problems?

Hi all, I have a weird problem.
I have a tilt and am using the HTC rom, I connect to wifi in my apartment and 3G or HSDPA when I leave the apartment.
When I'm connected through wifi, my Slingplayer works flawlessly, finds my slingbox, and plays the video. When I try to connect outside using 3G/HSDPA, I get "Cannot connect with current connection settings"
I know the Slingbox is working correctly because I can connect to it through a desktop PC without a problem, and I know that the 3G works fine on my tilt because I have no problem loading websites, using mundi, etc.
Any ideas? I've seen a couple other posts on other forums with the same problem but there were no responses on them.
Thanks!

Can you connect to anything else when on 3G?
Try your proxy settings
Did you change the default ports on the SlingBox config?
Are those ports (default or modified) open from the outside of your firewall/router?
If you have the ability to monitor inbound connections try monitoring while you connect through 3G and see if your device attempts on the correct port and that it is NATed to the correct IP and port.
Raptor

I had exactly the same problem with my Belkin router. You need to set up a port on your router in order for it to work. I know on mine it involved setting up a virtual server.

I am using the TyTN II and I am having the same exact problems. I think AT&T killed access to slingbox somehow. I can surf the internet just fine, and then as soon as I start the slingplayer, my connection gets lost and my phone says "cannot sonnect with current connection settings." Any help would be appreciated, especially with the World Series coming up this week.

cjf2014 said:
I know the Slingbox is working correctly because I can connect to it through a desktop PC without a problem
Click to expand...
Click to collapse
Possibly a silly point but can you definitely connect over the internet to it? Or just over your LAN?
There's a wizard that enables the port forwarding for you - (called Remote Viewing or something?) should be with the software for the slingbox.
Could be that your desktop is just going direct over the LAN?
Also, I had problems when I was just using the automatic settings to configure the box - in the end it works far better if you ignore the UPnP stuff, and use the manual setup process (or so I found). Again, the desktop software wizard steps you through this.

If you can connect over wifi at home, but not over wifi or 3g when away, then unless AT&T are blocking the ports, its more likely your router settings, as at home you are inside your LAN but elsewhere you have to go through your routers hardware firewall.
Just have a look at slingbox's help files.

SlingBox works fine on AT&T. Check your proxy settings on the phone. Try the "remove hidden proxy" cab. The home router also needs an outgoing port defined as well. Good Luck, I know it can work.

I will bet that it's your router/firewall blocking the incoming net traffic. Try connecting to it from a Friend's internet connection or a public computer at the library or something.

Had a similar problem with slingplayer mobile on my new HTC TouchPro- phone from Vodafone but I put in my T-mobile SIM as I wanted to keep the Web and walk.
Slingplayer worked fine from Vario3 with same sim but not from TouchPro. Eventually unticked the use proxy server in the connection settings and it started to work. Weird, as on the Vario the proxy box is ticked and it works.
Anyway, worth trying if anyone else is having problems.

One of two things, either you have not port fowarded your router to allow the Slingbox to be remotly viewed, go to portfoward.com for exact instructions for your specific router, or your hidden proxy is messing with it. More than likley its not port fowarded correctly. BTW...when your in your home network, i.e... using WiFi, it will work without the router being fwded because your slingbox is already inside your home network. When coming from the outside of your home network through 3g or whatever your router has to allow access to the slingbox.

WM6 internet sharing with whole network

Hi, I have a Tilt and do not have a problem tethering to a single computer. What I would like to do is share with all four computers in my home. I have tried bridging the sharing connection to my lan connection and have gotten dhcp on the Tilt to assign addresses to all computers on the network, but they still can't ping each other (other than the tilt and the computer its directly tethered to. I have turned off all firewalls and still nothing. Rebooted everything. Still nothing. Is it possible to do this? Thanks for any help.

There's a program around here somewhere that allows you to make your TILT a wireless router. If you do this, any machine with wi-fi can connect to the SSID and go.
Anyone have the link handy?

Wireless Router
Could I have it connect with my current wireless router to provide internet to my wired network through the rj45 ports on the router ? 3 of the 4 computers are on a wired lan. You see, we just got HSDPA on Monday and I love it. I got a bit ahead of myself and cancelled my home DSL connection. Now I'm realizing that I am stuck with only having one computer on the internet at a time. This has got to be possible. - I just found the thread on setting up as a wireless router. I will start playing with it. Any suggestions/instructions are appreciated.

OK, get connected to your carrier whilst tethered.
Then from any Explorer window on your tethered PC, select, 'Set up a home or small Office Network'.
Select the first option in the following box 'This computer directly connects...' and follow it through.
This should set up your Activesync PC as an IP address of 192.168.1.1. (an access point IP)
If you connect any other PC/laptop to this PC via wireless or LAN (you do know how to do that I hope??) to this computer, it will share the internet connection..
Remember, this will change any prior Internet configuration you have on the PC/Laptop!
Hope this helps.

Internet sharing
Thanks for the suggestion. I am going to try that again. The first time I tried that I found out that the Tilt had already assigned itself the address of 192.168.0.1 . On the XP machine, the computer will always use that same address to share its connection, so it immediately complained that another computer on the network is already using the required address for internet connection sharing. Maybe all I need to do is force the Tilt to use a different ip address like 192.168.0.10? I am not sure how to do that since this is my first time using Windows Mobile as part of a network sharing its connection. The only reference I could find to 192.168.0.1 in the registry was HKLM\Comm\BTPAN1\Parms\TcpIp. Should I change that?

jebrown1 said:
Thanks for the suggestion. I am going to try that again. The first time I tried that I found out that the Tilt had already assigned itself the address of 192.168.0.1 . On the XP machine, the computer will always use that same address to share its connection, so it immediately complained that another computer on the network is already using the required address for internet connection sharing. Maybe all I need to do is force the Tilt to use a different ip address like 192.168.0.10? I am not sure how to do that since this is my first time using Windows Mobile as part of a network sharing its connection. The only reference I could find to 192.168.0.1 in the registry was HKLM\Comm\BTPAN1\Parms\TcpIp. Should I change that?
Click to expand...
Click to collapse
NO, 192.168.0.1 or 2.1 or.3.1 are all access point AD's.
You have to go into your PC/laptop Network Places icon to tel IT to then share the connection.
I am sorry, but if you have never shared an internet connection on your PC before (ie via modem or ADSL), you will not really understand how it is done.

Access points
Thanks for your reply. The problem is that we are trying to make the pc an access point and trying to make the tilt an access point at the same time. They both are using 192.168.0.1 as the default ip address and as far as I tell there is not a way given to change that. The Tilt automatically uses 192.168.0.1 and when you using the sharing wizard on the pc it also uses the same address for its network card thats connected to the home wired network. Unfortunately for me, two devices on a network cannot have the same ip address. There must be a way...

jebrown1 said:
Thanks for your reply. The problem is that we are trying to make the pc an access point and trying to make the tilt an access point at the same time. They both are using 192.168.0.1 as the default ip address and as far as I tell there is not a way given to change that. The Tilt automatically uses 192.168.0.1 and when you using the sharing wizard on the pc it also uses the same address for its network card thats connected to the home wired network. Unfortunately for me, two devices on a network cannot have the same ip address. There must be a way...
Click to expand...
Click to collapse
OK, set all computers on the network to fixed IP's of 192.168.0.xxx in Internet protocol (under TCPIP on network)with the same subnet mask with a default gateway matching your device! Try that...

sharing
That was my first attempt at a work around. The problem is that there are
actually two network connections to the pc. One for the Tilt (usb) and one for the LAN (nic card). They don't seem to see each other even when they have matching ip addresses and subnets. Thats why I tried right clicking them and selecting "bridge these connections." It seems that internet sharing "requires" DHCP to be used. I tried setting all the computers to use DHCP and actually had the Tilt assigning ip addresses to all of the computers on the network by bridging the two connections and using dhcp. Oddly, though, the computers on the network could not ping the Tilt. I think its because bridging uses the data link layer of the osi networking model?

There must be a hack to change the ip address that windows uses for the sharing access point. Alternatively, it would be nice if there were a device out there that could act as a hub to network usb and 100baseT devices together. In other words, plugging usb and cat5 cable rj45 plugs into the same box and having them all be on the same network.

OK, I have asked smitty to get on this but both of us are WAYYYYy past our bedtimes.
He should get back to you tomoz on this. (he's the Network buff..)
Hope it works out..

this is the app mentioned earlier and may help your solution...
http://forum.xda-developers.com/showthread.php?t=341398

I can't make this work. I don't have WiFi on all of my computers. I was hoping to use WMWifiRouter to connect to my wireless router and then to my whole wired network. Is there a way to make the Tilt wireless router to connect with another wireless router? I'm thinking what I will do is go back to an AT&T rom and use "wireles modem" instead of "internet sharing". That way I can share the modem with the whole network. There doesn't seem to be a good way to use the Tilt internet sharing with the whole network. What do you guys think?

Deleted.....

For any future readers of this thread: I put the stock AT&T rom back on this phone and did a soft reset during the initial boot to stop the bloatware from loading. I went to start>settings>connections and tapped the wireless modem icon to open the app. I selected "usb" and tapped done then plugged the usb into my computer. My win xp computer found the new modem hardware and installed the HTC modem driver. I then setup a new dialup connection on my computer, and used the following to setup the login and dial:
username: [email protected]
password: cingular1
dial #: *99***1#
When I clicked on dial, it quickly connected to the AT&T network and I had internet access on my computer! I went to a speed test website and clocked my download speed at 1.2mbs and upload at 300kbs. I then opened "my network" and started the network setup wizard. I selected "this computer connects directly to the internet" and "file and printer sharing". To make a long story short, I am now able to share the Tilt's HSDPA internet connection with my whole network! I could not do it using the internet sharing function of the Tilt with either the AT&T rom or the kaiser rom. It would be awesome if someone more educated than me could make this function part of the HTC kaiser rom.

Nojnaworb wrote:
.....the problem is that we are trying to make the pc an access point and trying to make the tilt an access point at the same time. They both are using 192.168.0.1 as the default ip address and as far as I tell there is not a way given to change that. The Tilt automatically uses 192.168.0.1 and when you using the sharing wizard on the pc it also uses the same address for its network card thats connected to the home wired network. Unfortunately for me, two devices on a network cannot have the same ip address. There must be a way.......
I have same problem. I agree with Nojnaworb, this is the reason why its not working.
I have no Wifi at home and have to use LAN for my home network (2 PC + 1 ppc).
Under WM5 it was easy to share Internetconnection with all Lan adapters.
I cannot believe there is no way.
PLS Networkexperts, tell me how to setup !!

Its really quite simple.
You dont connect all the computers to the tilt. You use ICS on the tilt to provide one pc with an internet connection.
You then share the internet connection from that pc to the other pc's using the networking wizard.

I think part of this persons problem was that he needed to bridge the 2 connections.
here have this.
http://www.windowsnetworking.com/articles_tutorials/wxpbrdge.html
You should be able to connect the Tilt, (let it use whatever address it wants) and then make a bridge from the tilt to your nic in the server. Then I beleive you just use internet connection sharing to disperse the lovely packets to the rest of the network. Without the bridge, there is no way to share from one network to another.
I'm pretty sure that you will need to set the address to 192.168.0.2 on the server or any other number were the 2 is. If your using a router then I would suggest turning off dhcp and not using the WAN port on it. Just treat the router like a switch/hub because it will just makes things even harder to figure out.
wish we had service that was worth sharing to my network.

Can you access the internet when connected via ActiveSync?

With my trusty old Ipaq 5550 i could, but for some reason i cant with my Kaiser.
I had a look in the manual but couldnt find this.
Any tips?

It should work automatically.
Perhaps in your comm manager, active sync is greyed out and needs to be enabled.
Or perhaps in your configuration screen: connections tab, usb on pc (or sometinglike that), you can (un)check a box about advanced network connectivity.

yes for me work You must change in Connections->Advanced->Select network first field where you have your ISP to My Work Network.

Stay0Puft said:
perhaps in your configuration screen: connections tab, usb on pc (or sometinglike that), you can (un)check a box about advanced network connectivity.
Click to expand...
Click to collapse
EXACTLY.
Mine was checked, once i UNchecked it. I had internet conectivity.

I have all default and CHECKED use advanced network functionality and it works fine, even when syncing over bluetooth I can get to the internet through ActiveSync

Thanks, been wanting to do this for ages.
Now I have got it working.

Okay, this is a long message but I have had a unique problem in which I had to fiddle with activesync and my PDA for several days to figure it out. So in case this is your problem look here.
Scenario:
At my work we have a proxy server. When i connect my phone to my computer, even though activesync and my PDA are set to connect properly neither my phone nor my computers internet works. I fooled with this, posted on the forums and finally found a way to fix it.
Steps:
1)Change your PDA's advanced network settings in the network management area to BOTH be "mywork network". Do this before plugging in to activesync.
2)load an internet page with streaming content, or constantly refresh a web page if your work blocks all sites!
3)Ensure that your activesync is set to connect to the "work network".
4)Plug in your phone (be sure that data is still streaming on your desktop, if an active connection isn't streaming on your desktop Windows uses logarithms to decide which connection to use as an internet source).
5)Let activesync load and syncronize. Once it is syncronized, go back to your pda's network management page and change the two options BACK to MEdia Net or whatever data service you use on your cell phone. NOTE: Be sure that media is streaming all the way until you change your PDA's options BACK to the proper internet source for your phone and test it by loading a web page. Once the phone is set as it's own internet source and the desktop still has it's active LAN connection you should be golden.
I know you shouldn't have to do this but at least with my works network and their proxy server if i don't do it this way i will NEVER be able to use the internet on either device.
The reason for this is because of Microsoft's crappy network capabilities. In activesync 4.0 + they made activesync use an actual network connection, you can view it via the network connection page. So with some networks (not all) it tries to use your phones connection as the active internet network and vice versa at times.
Hope this helps somebody out there as this drove me nuts!
So far i'm the only person that has had the problem (on this forum, at least that has responded to my threads). But i'm sure there are a couple other people that have annoying problems with their work and activesync.
Thanks,
Luke

Thanks a lot alaiwy, worked just fine for me!

For the AT&T Tilt & AT&T ROM's you also need to disable the Proxy.

_Dejan_ said:
yes for me work You must change in Connections->Advanced->Select network first field where you have your ISP to My Work Network.
Click to expand...
Click to collapse
TY I was looking for this finally becuase that was getting very annoying as hell to me.

Wi-Fi connects but NO data transfer

Hi,
I have just got the Diamond and I have two main problem.
1) Although I have connected the Diamond to my Home wireless network, there is no data transfer. Opera can not open pages, Youtube can not start even I can not update weather?
2) When I connect the Diamond to the Laptop / PC, all PC's and Laptops connected to my home network (wireless) drop from the connection and never connect again?
Thank you for your kind help...

I have same problem with my Diamond.

1) go to: startmenu->settings->connections->Wi-Fi->networkcard/adapter->and make sure that it says "my networkcard/adapter connects to internet"Also at the same tab open IEEE 802.11b/g Compitable Wi-Fi Adapter and try to a static ip matching the one your pc uses. (not sure about it since i can't recreate the problem atm..)
2) Try the thing I suggested in this thread http://forum.xda-developers.com/showthread.php?t=417664 (plz use search next time)

bobo_error said:
1) go to: startmenu->settings->connections->Wi-Fi->networkcard/adapter->and make sure that it says "my networkcard/adapter connects to internet"Also at the same tab open IEEE 802.11b/g Compitable Wi-Fi Adapter and try to a static ip matching the one your pc uses. (not sure about it since i can't recreate the problem atm..)
2) Try the thing I suggested in this thread http://forum.xda-developers.com/showthread.php?t=417664 (plz use search next time)
Click to expand...
Click to collapse
Thanks for your reply, but both of solutions do not work for me...
Any other suggestion?
Thanks for your help..

Try turning on wifi, then go in LAN WIRELESS and change in "improved performance"

All of this do not work for me too...

Go to Wireless LAN settings and there to power mode and set yo best battery.... that worked for me.

in "settings => connections => WiFi" is "Connected". In "Wireless Lan" there is Connected too... In log on my router there is MAC adress of Diamond as associated and authorized. All seems OK. But on Diamond do not work any internet connection (Weather, web, etc...). With Active Sync works fine. Laptop with the same settings works fine. But Diamond with WiFi... no way :-(

Any other suggestions?

Same problem after i made ROM update from 1.7... to 1.93. before works fine. no other software is istalled.

Been having an issue with connecting to my wireless network also for the last week. My phone is from orange in the UK. My wireless router is an Dlink 614+ on Virgin cable broadband.
The Diamond would connect intermittantly but then say 'not avaiable' after a period of time, or when trying to reconnect after diasbling/enabling wi-fi in the comms manager. Also, after restarting my router the device would connect for a while but not seem to 'hold' it's connection.
When the device was 'connected' I could not get opera/youtube to load a page, even though I could see the diamond in my router's log showing it connected with a leased ip address. What made it so annoying was that every other wireless mobile device/laptop I have owned has connected without any problem at all, leading me to beleive there was a problem with the phone. Again, this was rather frustrating as the phone was detecting avaliable networks but just not 'holding' the connection nor 'using' the connection in opera/explorer etc.
After searching on xda-developers and other forums for a possible known issue, I tried all the various suggestions including;
i/ increasing to best performance under power mode in Wireless LAN settings
ii/ Hard reset of router (even though other wireless devices were connected fine)
iii/ trying static rather than dynamic ip for my diamond in router settings
iv/ disabling any security/encryption on my router
v/ entering DNS settings in manually into my diamond
vi/ changing 'connect to' under wi-fi neteorks to 'Work' rather than 'the internet'
vii/ tried various roms
and other suggestions I had read about - all which didn't make a difference!
I was about to send the diamond back to Orange (here in the UK) but decided to give it one last go and change my router. I bought a Netgear WGT624 for 25 quid from PC today world and my diamond connected
straight away without an issue, and opera/youtube/messager all connected straight away to the internet. I have not lost connection once. So thats how I resolved it - obviously my device did not like 802.11b (on the original dlink router) even though all previous smartphones have connected fine and the diamond's wireless adapter is labelled b/g.
Hope that stops anyone wasting a week like I did, I would try it out on another router before making any decisions because the chip in the diamond seems a lot more picky to what it connects to than anything I've used in the past!
cheers

Linksys WAG54 is OK, Freebox is not perfect
It really seems to depend on the WiFi router.
I've had probems with my French Freebox (my ISP's ADSL+wifi router) using WPA2 AES. It would work fine, for half an hour maybe, then it would stop. It says it's connected but there is no data transfer. You can switch WLAN off and on, soft reset the phone... nothing will do. Then it will work again later on.
I downgraded encryption to TKIP and i experienced the same problem.
But then I've tried my old Linksys WAG54G router, using the exact same encryption protocol and key and it works perfectly (for hours)!
I've also tested free access (Paris public Wifi, Mc Donald's...) and they work fine.
As my ISP wifi box does not let me have a look at all the settings (beacon time, etc.) it is very difficult to tell what makes it not-so-compatible with my Diamond... But there must be something.