Big problem with my Qtek during the upgrade - 8125, K-JAM, P4300, MDA Vario Software Upgrading

Hello,
Yesterday I tried to upgrade my QTEK 9100 so I followed the procedure here
and I am blocked !!!
The button rom stop at 98% and the Xda_MiniS_LaunchROM_v154102 stop at 85% .
So, now when I power it I have the tricolor screen.
On he Screen
RUU
IPL 1.05
SPL 1.03
Please tell me that I can do something for my Cellphone !!

Just retry flashing either of those ROM's until you get a good flash.

Related

strucked with boot loader screen in imate kjam

i bricked my imate kjam while upgrading to wm6.now strucked with bootloader screen.nothing can be done .please help.it shows ipl 2.16 and spl 2.16 on bootloader screen.it hapened when i tried upgrade to wm6 using sp5 upgrade tools.
Firstly, this is not brick. A brick is one that you can even power on the Wizard.
Flash with your K-Jam original ROM to get back your OS, then following the stickies in this forum to unlock your Wizard, then flash one of the WM6 ROMs here using bundled RUU application.
p.s I don't know what "sp5 update tools" is.
how to flash back my original rom in kjam.
Thanks for response.can u tell me where can i find step by step procedure for Flashing my K-Jam to original ROM to get back my OS, my ipl 2.16 and spl 2.16 . I dont want to do anything wrong from now.please tell.thanks.
sajipavithram said:
Thanks for response.can u tell me where can i find step by step procedure for Flashing my K-Jam to original ROM to get back my OS, my ipl 2.16 and spl 2.16 . I dont want to do anything wrong from now.please tell.thanks.
Click to expand...
Click to collapse
Download official k-jam Rom 'K-JAM_WWE_216901_2169101_020710_ship.zip' from official website of i-mate k-jam or from the following link below:-
ftp://ftp.clubimate.com
1.unzip the Rom zipfile,get your phone into bootloaders screen (multicolored screen)by pressing and holding down the camera button and the Power ON button together,the phone will start in bootloaders(multicolored screen) it'll show you ipl/spl 2.16
2.when in bootloaders,connect your phone with pc via usb cable, a small usb written will appear at the bottom of the multicolored screen of your phone.confirm it.
3.open the unzipped folder of the downloaded Rom,run the RUU icon in it(double click Ruu.exe)
4. follow the instructions and flash the Rom,after completion,your phone will restart and start working.
Good luck !
zabardast_1 said:
Download official k-jam Rom 'K-JAM_WWE_216901_2169101_020710_ship.zip' from official website of i-mate k-jam or from the following link below:-
ftp://ftp.clubimate.com
1.unzip the Rom zipfile,get your phone into bootloaders screen (multicolored screen)by pressing and holding down the camera button and the Power ON button together,the phone will start in bootloaders(multicolored screen) it'll show you ipl/spl 2.16
2.when in bootloaders,connect your phone with pc via usb cable, a small usb written will appear at the bottom of the multicolored screen of your phone.confirm it.
3.open the unzipped folder of the downloaded Rom,run the RUU icon in it(double click Ruu.exe)
4. follow the instructions and flash the Rom,after completion,your phone will restart and start working.
Good luck !
Click to expand...
Click to collapse
hi
I did the exact thing , I've got no errors during that but i still have a blue screen with these
IPL 2.16 , SPL 2.16 , GSM 02.07.10 , OS 2.16.9.1
what did i wrong?
thanks
hello, I am very new to this forum and also new to a windows phone. i will appreciate your patience and kindness to help me. I tried flashing an imate kjam using SOFTSPL. I am now stuck at the muilticolored screen displaying IPL 2.16.0001, SPL 1.06
I dont even know what to do now. i downloaded 'K-JAM_WWE_216901_2169101_020710_ship.zip' from rapidshare and when i tried loading its saying invalid vendor id. unfortunately we can access the clubimate website here in south africa.
Please help me gurus and evryone who has the mercy for me.
Thank you so much..
IPL 2.16.0001 = G4 and SPL 1.06 = G3 this means your phone is bricked.
To my knowledge nobody has recovered from this.
only ahmar sohail can do that
So ahmar sohail plz help my imate stuck and i love my fone
djkata1 said:
So ahmar sohail plz help my imate stuck and i love my fone
Click to expand...
Click to collapse
why do not you use WST to solve problems on your device..???

what is wrong with my XDA Mini S

Short version:
I have an xda Mini S
ipl 1.01
spl 2.21
OS 10.1.0.811
I was running the mfrazzz WM6 I think it was vers XM6r5 RC1. I tried to updgrade my ROM to a new one because if issues I was having with this version. It was great but I could no longer surf the web and my unit would crash with the WAN and internet running.
I had to CID unlock my phone last July to get this XM6r5 RC1 to run (I believe I did anyway).
Today I attempted to flash the button ROM to my phone and it made it about 22% then the phone reset and crashed (started to loop on and off at the green, yellow and blue screen). Now it starts to update the rom but most of the time it reenters that loop shortly after the button rom app starts. The battery was full when I started. I have tried 2 different PC's with no luck. Any help would be appreciated.
Additional info: the reason I tried to upgrade the phone was it would crash when accessing the web via wifi (just recently). When connected to the PC it was fine. If I used the wifi sometimes it would work for 5 mins sometimes none but everytime I would it would crash and start to loop on and off crashing at the splash screen showing the IPL and SPL. The only way to recover it was to pull the battery. It is now doing this reboot loop at the bootloader screen when it crashes).
I hope thats not TMI but I really want my phone working again.
I just discovered that it will start the reboot sequence regardless of whether it is plugged in or not. It will start randomly rebooting once it is turned on. I tried installing the RUU Hermes Qtek rom and now it is telling my my ipl is 2.26 as well as my spl.
Please help!
hi
I have a o2 mini s too mine is g4 i dont know yours but if you have hard spl you shouldnt flash official rom if you said that you have 2.26 ips slp then you should not have problems flashing to your official rom but if that doesnt help use the wizard love.
Hope i help.
gdtymze
Its really strange,if you say you had XM6r5 RC1,which is your device, G3 or G4 ?,cuz if you have a G3 phone,how come you have ipl 1.01 and spl 2.21.wm6 roms cannot be installed with ipl1.xx,got to have ipl/spl 2.xx. Also you say you Cid unlocked the phone.Are you sure ,it was xm6r5 OS ,which was running on your phone ? How did you flash it ? with ipl 1.01 and spl 2.21 ?
Well,if you have a G4 device,its not possible to CID unlock it and IPL shud have been 2.21.0001 and the SPL is 2.21.olip ? after HardSPL and in SoftSPL IPL/SPL remains the same as the original ipl/spl e.g 2.21.0001.
Would you plz be more specific and explain what the status of your phone is and what exactly you did before ?
Cheers!
zabardast_1 said:
gdtymze
Its really strange,if you say you had XM6r5 RC1,which is your device, G3 or G4 ?,cuz if you have a G3 phone,how come you have ipl 1.01 and spl 2.21.wm6 roms cannot be installed with ipl1.xx,got to have ipl/spl 2.xx. Also you say you Cid unlocked the phone.Are you sure ,it was xm6r5 OS ,which was running on your phone ? How did you flash it ? with ipl 1.01 and spl 2.21 ?
Well,if you have a G4 device,its not possible to CID unlock it and IPL shud have been 2.21.0001 and the SPL is 2.21.olip ? after HardSPL and in SoftSPL IPL/SPL remains the same as the original ipl/spl e.g 2.21.0001.
Would you plz be more specific and explain what the status of your phone is and what exactly you did before ?
Cheers!
Click to expand...
Click to collapse
Ok please bear with me my recollection is hazy on this. Last August my phone was runnging the O2 software. After checking in here I identified my phone as a G3 phone. I then checked to see if it was CID locked (after doing a posted test it appeared to be). I don't recall how I did the CID unlock. I followed the CID and flashing insructions posted somewhere in the xda-developers forum (it may have been with the rom I used (mfrazzz version) I think I flashed the original O2 xda software from the O2 site then I flashed the Wm6 to my phone I believe it was XM6r5 RC1. I think it was the XM6r5 RC1 only because when it would boot I would see 3 splash screens. First was a Cylon witht he HTC logo, followed by an orange speedometer (with the IPL listed as 1.01 and spl as 2.21 OS was 10.1.0.811 and I don't know that the GSM numbers were) and the third was the splash screen from mfrazzz (dark blue/green with mfrazzz on it). I am pretty sure it was the XM6r5 RC1 build but I could be wrong I think it was the latest at that time. It was stable for several months (basically until 2 weeks ago) when I deleted the recycle bin and temp fold from the memory card (not the device). After that if I accessed the web via wifi it would crash then go into a repeating loop and the LED would change from green to red. The only way to stop it was to remove the battery. I don't know what else to tell you. When I left it yesterday it was at ipl/spl of 2.26 after initiating a RUU hermes . . . . I left it overnight started it up with button rom and it made it 60% then started looping again and gave the error code 274. A second attemp made it to 14% then code 302 (it started to loop again. It still says ipl/spl 2.26. I'm really at a loss here.
ok, I believe,what you are saying must be true,anyway,its not common or observed or even seen to have ipl 1.xx and upgrade to a wm6 rom,untill you have a cid unlocked phone with ipl/spl 2.xx, I'm really,rather, surprised,how you got it!!! or you might have got ipl 1.xx after now again flashing Button's Rom 1.05,the second time now.
Anyhow,now download the official carrier's rom or T-mobile 2.26 or xda_minis_launch Rom and try to flash and recover back to default status and check with WST tool,speciaaly the 'CID Action' button,to verify the SIN?CID lock/unlock status of the phone, then proceed further,ok
Cheers!
I don't know how I got it either. I do know that the ipl/spl while it was working was 1.01 and 2.21. After my first few attempts to load the button rom and then a version of the hermes and t-mobile rom, my phone boots to the bootloader screen and has ipl/spl of 2.26. I have attempted the t-mobile rom a few times but the most successful was the initial attempt after letting it sit over night. It almost made it through (80%) with the t-mobile rom then it crashed and started its loops again. Subsequent attempts made it to as high as 60% and as low as 14%. Is it possible to charge the battery while it is in boot loader mode, perhaps with a wall charger and not plugged into the PC. I ask b/c I am worried my battery may be getting too low and also when it is plugged into the pc it boots automatically. Perhaps I should ask this but do you know where I can get the xda_minis_launch Rom I have searched here and google and no luck. What i did find here http://wiki.xda-developers.com/index.php?pagename=Wizard_Upgrades gives me an error 530 unable to switch message.
Thanks for your help!
gdtymze
ok, try out this link below,you'll find all the requirements here and guidance.
http://wiki.xda-developers.com/index.php?pagename=Wizard Windows Mobile 6 for newbies
Goodluck
Thanks! I will dl that and try that rom. Have you heard of a phone rebooting like mine does? Today once again I was able to start RUU (t-mobile) and once again it made it to just over 80% and then the phone would reboot and start looping until I removed the battery. I tried again immediately and it made it just past the phone verification before it started the reboot loop. Since then I have been letting it sit. Any suggestions or ideas as to why it would do that?
Thanks for your help.
Your are welcome !
It won't charge in bootloaders mode or from the pc via usb cable,but you can charge it with a wall charger and its always better and recommended to have a fully charged battery before flashing.
Cheers!
So if it is powered off and I use a wall charger then it should charge. When I started this process the batter had a full charge but I have no idea where it is at now that I have attempted to flash it so many time. With the new rom it only makes it about 65% then it loops. It is really starting to wear my patience.

wizard stuck on bootloader

hello.
i had problem with wizard. i tried to upgrade rom, but i cant. it stuck on 99% and gives an error. i think it had cidlock, but i cant unlock it from bootloader.
Please help...
Piechcio said:
hello.
i had problem with wizard. i tried to upgrade rom, but i cant. it stuck on 99% and gives an error. i think it had cidlock, but i cant unlock it from bootloader.
Please help...
Click to expand...
Click to collapse
Download official stock rom of your carrier and flash it in bootloaders to recover back to its default working status,then if its a G3 phone, downgrade to ipl/spl 1.xx by flashing Button's Rom and SIM/CID unlock with lokiwiz02b,but if its a G4 ,it cannot be CID unlocked but can be upgraded to wm6 through 'SoftSPL' or 'HardSPL'.
HI
I have a same problem – I have a qtek 9100 G3
ipl-spl 2.17
GSM 02.07.10
OS 2.17.7.2
I can update my rom completely but after restart freeze on ipl-spl screen
And I can’t warm reset it says FORMAT PARTITION FAIL
I try to downgrade my rom but spl freeze on 2.17 – I try button rom and Xda_MiniS_LaunchROM_v154102
I can’t find any official qtek rom for test
And I also try R2SD all with romupdate115 it not work
help please
jalalkarimi said:
HI
I have a same problem – I have a qtek 9100 G3
ipl-spl 2.17
GSM 02.07.10
OS 2.17.7.2
I can update my rom completely but after restart freeze on ipl-spl screen
And I can’t warm reset it says FORMAT PARTITION FAIL
I try to downgrade my rom but spl freeze on 2.17 – I try button rom and Xda_MiniS_LaunchROM_v154102
I can’t find any official qtek rom for test
And I also try R2SD all with romupdate115 it not work
help please
Click to expand...
Click to collapse
You got to have a CID unlocked phone to upgrade to any wm6 Rom.Sometimes SPL do get stuck up at 2.xx while downgrading with Button's Rom,it takes a couple of tries to get it downgraded to 1.xx.Flash the button's rom a few times more till it gets downgraded.You can only CID unlock your phone,if it has IPL/SPL 1.xx.
Download the official stock Qtek Rom from this link:-
http://forum.xda-developers.com/showthread.php?t=342744
zabardast_1 said:
You got to have a CID unlocked phone to upgrade to any wm6 Rom.Sometimes SPL do get stuck up at 2.xx while downgrading with Button's Rom,it takes a couple of tries to get it downgraded to 1.xx.Flash the button's rom a few times more till it gets downgraded.You can only CID unlock your phone,if it has IPL/SPL 1.xx.
Download the official stock Qtek Rom from this link:-
http://forum.xda-developers.com/showthread.php?t=342744
Click to expand...
Click to collapse
Don't use those ROMs as they are for G4!!!
If flashing original ROM doesn't solve the case then you'll have to buy the unlock program from IMEI-check company.
Many thanks
Can you give me some advice what is the best version for qtek 9100 I can’t find any original qtek rom please give me a link
And if I buy IMEI Program after apply that my device starts normally?
I don’t want WM6 only back to normal
And serious problem is
I have FORMAT FAT FAIL for warm reset. In this case its possible hardware (disk on chip) has a hardware problem?
Thank you all
jalalkarimi said:
Many thanks
Can you give me some advice what is the best version for qtek 9100 I can’t find any original qtek rom please give me a link
And if I buy IMEI Program after apply that my device starts normally?
I don’t want WM6 only back to normal
And serious problem is
I have FORMAT FAT FAIL for warm reset. In this case its possible hardware (disk on chip) has a hardware problem?
Thank you all
Click to expand...
Click to collapse
No. the problem is simply of messed up firmware. I believe that the SPL tries to load the OS but it must be at a different address and never starts to load.
The IMEI-check tool will simply CID unlock your device. You still have to do the "r2sd all" procedure...
good luck

Ipl 1.04 spl 1.04 ?

Hi everybody,
I hope somebody can help me. I have a Charmer (T-mobile MDA compact II german) in front of me. A friend of mine tried to flash the original TMO (german) AKU3.3 and it failed with the "know" 95% bug.
Whatever was before and whatever he tried afterwards, I do not know that. He asked me for help to get it now back to live.
When turning it on the red/green/blue screen appears and on the screen I can only see:
IPL 1.04 RUU
SPL 1.04
I tried almost everything found in this forum but nothing really helped. The best result I archived was after flashing radio rom (Prophet_G3_G4_RadioRom_v2.69.21). Then I got a boot logo from HTC / QTek. While booting it shows again again IPL / SPL 1.04 and a OS Version. No GSM ver (!). But the screen does not go away an after about 45 sec. the device soft resets itself an it again goes into this QTEK screen.
Has anybody an idea what to do now? I'm a bit confused because the IPL/SPL version of this charmer is totally different to the ones here in the forum. I have 1.04 on both version.
Any help is much appreciated
***
I just bricked it
No bootloader anymore just a *very* short flashing of the display
R I P
I just bricked it
No bootloader anymore just a *very* short flashing of the display
R I P
Have you flashed any Bootloader from Wizard or Prophet? The only way out that is JTAG. But I don't know about it. I'll search and tell you this evening.

K-jam stuck on boot screen :(

hey guys and gals, my one friend gave me his k-jam to fix after he tried to flash it. I did follow the [READ FIRST] The Definitive Guide to Unlocking & Rom Upgrading G3 Wizards ( http://forum.xda-developers.com/showthread.php?t=285435 ) guide. I installed both the button and minis_Launchrom, both installed 100%, however it does not go past the boot screen.
IPL 1.05
SPL 2.26
GSM 01.12.10
OS 1.5.4.2
Any advice will surely help me a lot and thank you in advance.
saa044 said:
hey guys and gals, my one friend gave me his k-jam to fix after he tried to flash it. I did follow the [READ FIRST] The Definitive Guide to Unlocking & Rom Upgrading G3 Wizards ( http://forum.xda-developers.com/showthread.php?t=285435 ) guide. I installed both the button and minis_Launchrom, both installed 100%, however it does not go past the boot screen.
IPL 1.05
SPL 2.26
GSM 01.12.10
OS 1.5.4.2
Any advice will surely help me a lot and thank you in advance.
Click to expand...
Click to collapse
Hi: something similar happens in one wizard I got: trying to upgrade, the screen remains in the start:
ipl 1.01
spl 1.01
gsm 1.12.10
OS 1.5.4.2
(the rom with the beer photo at the start)
after some minute restart and the same screen.
If you try the hardreset, it is quite impossible to press the "send" button, and if you succeed nothing happen. It appear the "HTC Innovation" screen and so on.
If you put it into bootloader and connect the usb cable, the usb signal appear on the screen, but trying to install another rom the program says there is no device connected.
Any help also for me?

Categories

Resources