Bootloader information verification please!!! - Tilt, TyTN II, MDA Vario III General

I need someone who has not yet flashed Hardspl onto their tilt (tilt only), to verify the info displayed in the tri-color bootloader please. To get into bootloader you need to hold down Power + camera while resetting with the stylus, Thank you!

Cmon now, 12 views so far and no response?? I know someone out there has to have this information!

Hi,
Just seen this - I've flashed mine and my bootloader screen says:
KAIS130 MFG
SPL-1.0.OliPof
CPLD-8
Sorry - just re-read this - doh! Sorry to have wasted your time
HTH
Matt

Related

Trying to Unlock MDA Vario III with HTC_Hermes_SIM_CID_Unlock_v3a

@All
i'm trying to unlock one MDA Vario III as its mentioned that its supported by HTC_Hermes_SIM_CID_Unlock_v3a i've done everything HARD SPL is successfull but still i can't unlock it always getting error when try to update it. always get error on 7% which is shown in picture.
picture is attached for the reference.
on boot loader screen i can see following Information with Tri Color
KAIS130 MFG
SPL-1.0.OliPof
CPLD-8
and when i power on phone normally i can see following information.
R 1.27.12.32
G 22.45.88.07H
D 1.56.00.00
Take Care
ENJOY
The Vario III is technically a Kaiser. So I would suggest trying to Kaiser Unlocker instead. Just to be sure.
JimmyMcGee said:
The Vario III is technically a Kaiser. So I would suggest trying to Kaiser Unlocker instead. Just to be sure.
Click to expand...
Click to collapse
thanks for your TIP , unlocked successfully.
Take Care
ENJOY

Please verify my Supercid installation.

I just installed the Supercid and I wanted to make sure I have it installed properly. where can I check it? the reason I am asking, because instruction stated I should see the unlockcode on your monitor and your Kaiser is being restarted automatically. I do not see the unlockcode and device did not restart, but it that give me this message.
=== Kaiser SuperCID and Security Unlocker (c)2008 by jockyw2001
=== Donations happily accepted, paypal to [email protected]
[] Done, your device should now be superCID and Security Unlocked
[] Your device is unlocked and you can change anything anytime
[] Don't forget to flash your original radio
Press Enter to exit
Please advise. Thanks in advance
Anchim
anchim said:
I just installed the Supercid and I wanted to make sure I have it installed properly. where can I check it? the reason I am asking, because instruction stated I should see the unlockcode on your monitor and your Kaiser is being restarted automatically. I do not see the unlockcode and device did not restart, but it that give me this message.
=== Kaiser SuperCID and Security Unlocker (c)2008 by jockyw2001
=== Donations happily accepted, paypal to [email protected]
[] Done, your device should now be superCID and Security Unlocked
[] Your device is unlocked and you can change anything anytime
[] Don't forget to flash your original radio
Press Enter to exit
Please advise. Thanks in advance
Anchim
Click to expand...
Click to collapse
All looks good, but...
To verify security unlock, you can check here: http://forum.xda-developers.com/showpost.php?p=2580429&postcount=198
To test sim unlock use this command with ATCommander:
Code:
Enter into ATCommander:
[B][email protected]?40[/B] ---> check phone sim lock
Results
[B]@SIMLOCK= 00[/B] ---> means phone is unlocked
[B]@SIMLOCK= 01[/B] ---> means phone is locked
I can't remeber where to test CID unlock. If the above 2 are true, your probably OK.
Ta
Dave
DaveShaw said:
I can't remeber where to test CID unlock. If the above 2 are true, your probably OK.
Ta
Dave
Click to expand...
Click to collapse
Depending on what Unlocker you use. Boot into Bootloader, (Press the Camera Key all the way in and Press your Stylus into the Reset Hole.)
Then Check at the top that it says "Security Unlocked"
JimmyMcGee said:
Depending on what Unlocker you use. Boot into Bootloader, (Press the Camera Key all the way in and Press your Stylus into the Reset Hole.)
Then Check at the top that it says "Security Unlocked"
Click to expand...
Click to collapse
I know that !
In the link I posted there's a AT command to test for "security unlock".
I can't however remeber how to check if the CID lock is on or not, I suppose it depends on the SPL, Hard SPL's wont have a CID check, OEM ones will.
Ta
Dave
OP- Search and ye shall find the answer to almost any question you can come up with. They have all been asked already.
Thanks everyone for your respond. The only thing that worry me is, I didn't see the unlockcode and the device didn't restart on it own like the instruction said. This is the tool I used, Kaiser-SuperCID-tool. This info from the bootloader screen.
KAIS1*0 MFG
SPL-1.0.oliPof
CPLD-8
Thanks
anchim said:
Thanks everyone for your respond. The only thing that worry me is, I didn't see the unlockcode and the device didn't restart on it own like the instruction said. This is the tool I used, Kaiser-SuperCID-tool. This info from the bootloader screen.
KAIS1*0 MFG
SPL-1.0.oliPof
CPLD-8
Thanks
Click to expand...
Click to collapse
Yeah, you'll be fine, go forth and flash a ROM.
Disclaimer, I am not always right.
Poirot said:
Despard: I suppose even you have failed?
Poirot: The last time was twenty-eight years ago
Click to expand...
Click to collapse
Dave
Be aware of your SPL version. It will probably need to be updated. Search for JockeySPL for the expert advice. I think all 6.1 ROMs need to be version 3.xx SPL. Anyway, search it out to avoid issues. Sounds like you are on your way to ROM goodness.
kimtyson said:
Be aware of your SPL version. It will probably need to be updated. Search for JockeySPL for the expert advice. I think all 6.1 ROMs need to be version 3.xx SPL. Anyway, search it out to avoid issues. Sounds like you are on your way to ROM goodness.
Click to expand...
Click to collapse
kimtyson means the Hard SPL's from here: http://forum.xda-developers.com/showthread.php?t=396922.
Searching for JockeySPL return's nothing much use
Dave
Thanks for the assist Dave. You are the man!
DaveShaw said:
Yeah, you'll be fine, go forth and flash a ROM.
Disclaimer, I am not always right.
Dave
Click to expand...
Click to collapse
Thanks again for your reply. I have been using [Apr 29] Dutty's WM6.1 Hybrid v2 5.2.19716/5.2.19700 since I installed SPL-1.0.oliPof. everything seem fine. should I need to upgrade it and which version to install?
Thanks
Anchim
anchim said:
Thanks again for your reply. I have been using [Apr 29] Dutty's WM6.1 Hybrid v2 5.2.19716/5.2.19700 since I installed SPL-1.0.oliPof. everything seem fine. should I need to upgrade it and which version to install?
Thanks
Anchim
Click to expand...
Click to collapse
Flash and SPL from here if you are using WM6.1.
The ROM chef normally suggests the exact version. Anything 3.* will be OK.
Ta
Dave
DaveShaw said:
All looks good, but...
To verify security unlock, you can check here: http://forum.xda-developers.com/showpost.php?p=2580429&postcount=198
To test sim unlock use this command with ATCommander:
Code:
Enter into ATCommander:
[B][email protected]?40[/B] ---> check phone sim lock
Results
[B]@SIMLOCK= 00[/B] ---> means phone is unlocked
[B]@SIMLOCK= 01[/B] ---> means phone is locked
I can't remeber where to test CID unlock. If the above 2 are true, your probably OK.
Ta
Dave
Click to expand...
Click to collapse
Thank you, Dave. Again.

Crashed on bootloader !!

hello all!
after a hard reset my tytn2 crashed on the bootloader multicolored, impossible to resolve, in bootloader marked:
KAIS130 MFG
SPL-1.0.OliPof
CPLD-8
and lowest on the white stripe ago marked serial and if I connect the USB plug ago marked usb
I tried with the small soft mtty but I get an error, probably vista.
Thank you for your help.
HDG said:
hello all!
after a hard reset my tytn2 crashed on the bootloader multicolored, impossible to resolve, in bootloader marked:
KAIS130 MFG
SPL-1.0.OliPof
CPLD-8
and lowest on the white stripe ago marked serial and if I connect the USB plug ago marked usb
I tried with the small soft mtty but I get an error, probably vista.
Thank you for your help.
Click to expand...
Click to collapse
Have a look here for solutions: http://forum.xda-developers.com/showthread.php?t=423486
Ta
Dave

[Q] HTC HD7 half briked >> USB enter host mode after update[Q]

Good evening,
I "half-bricked" my HD7 ...
since it has two updated via zune
by chance, I try the bootloader
miracle and the screen with 3 color bands
and with 4 or 5 lines of writing, but ke I do not have time to read very quickly because there comes a light gray screen with a blue print "enter usb host mode" ...
So here my question what can I do now to install a Rom mango unlocked without re stupidity
Finally, already is that possible??
Thank you very much for your help
as I was comfortable with wp wm as I am lost
titeloo said:
Good evening,
I "half-bricked" my HD7 ...
since it has two updated via zune
by chance, I try the bootloader
miracle and the screen with 3 color bands
and with 4 or 5 lines of writing, but ke I do not have time to read very quickly because there comes a light gray screen with a blue print "enter usb host mode" ...
So here my question what can I do now to install a Rom mango unlocked without re stupidity
Finally, already is that possible??
Thank you very much for your help
as I was comfortable with wp wm as I am lost
Click to expand...
Click to collapse
Whats your current SPL? (Holding down the Volume (-) + Power)
THANK YOU VERY MUTCH FOR YOUR HELP
in the screnn it's write
PD29100 SS-BC (4k)
SPL-5.10.2250.0(132968) mng
MicroP(LED) 0x07
TOUCH S1(v1.8,#1624)
SD SANDISK 7580MB
Partition Info-v211v413
F400
titeloo said:
THALK YOU VERY MUTCH FOR YOUR HELP
in the screnn it's write
PD29100 SS-BC (4k)
SPL-5.10.2250.0(132968) mng
MicroP(LED) 0x07
TOUCH S1(v1.8,#1624)
SD SANDISK 7580MB
Partition Info-v211v413
F400
Click to expand...
Click to collapse
if you can read all that your phone isn't bricked.
and it isn't half bricked to.
it is just updated to spl 5.10 and you can't use the H/R spl from cotulla on this (so don't try that because then you will get a half bricked phone)
there are some tut's here on xda how to roll back to a lower spl.
here is a link to a tut to roll back:
http://forum.xda-developers.com/showthread.php?t=1371073
really thank you for your help again.
before i do the update it's was only one line written
because i have do a mistake trying install hspl
but after two update via zune, the SPLscreen is like i've written before
now i haven't other solution to downgrade the spl ?
because i just want to install advanced config , and that look very complicate to downgrad spl
( sorry for my bad and english )
Moved to HTC HD7 General
This is a device specific question, not in the development section please.
please refer to the read before posting stcky for guidelines.
Take it easy
O_G

Splash screen stuck-assistance needed

If is there anyone active on this thread, for this old bugger, please assist.
I'm on SPL, non hard, no CiD unlock no nothing
The kais 130 enter tricolor mode with no problem.
It is the mda vario iii model from tmobile with cid tmob101. I cannot find anywhhere a stock rom that works as all says invalid vendor id.
When booting i can see the t mobile logo and radio verion but it is stuck. When trying mtty boot command it says unknown command.
Trying to use sd hardspl with the kaisdiag and kaisimg file but it stucks at Loading screen and does nothing.
Any idea on what to do next?
I know its a longshot as it is an old device, but maybe some old user may help as i am trying to bring this classic back life.

Categories

Resources