Crashed on bootloader !! - Tilt, TyTN II, MDA Vario III General

hello all!
after a hard reset my tytn2 crashed on the bootloader multicolored, impossible to resolve, in bootloader marked:
KAIS130 MFG
SPL-1.0.OliPof
CPLD-8
and lowest on the white stripe ago marked serial and if I connect the USB plug ago marked usb
I tried with the small soft mtty but I get an error, probably vista.
Thank you for your help.

HDG said:
hello all!
after a hard reset my tytn2 crashed on the bootloader multicolored, impossible to resolve, in bootloader marked:
KAIS130 MFG
SPL-1.0.OliPof
CPLD-8
and lowest on the white stripe ago marked serial and if I connect the USB plug ago marked usb
I tried with the small soft mtty but I get an error, probably vista.
Thank you for your help.
Click to expand...
Click to collapse
Have a look here for solutions: http://forum.xda-developers.com/showthread.php?t=423486
Ta
Dave

Related

Bootloader information verification please!!!

I need someone who has not yet flashed Hardspl onto their tilt (tilt only), to verify the info displayed in the tri-color bootloader please. To get into bootloader you need to hold down Power + camera while resetting with the stylus, Thank you!
Cmon now, 12 views so far and no response?? I know someone out there has to have this information!
Hi,
Just seen this - I've flashed mine and my bootloader screen says:
KAIS130 MFG
SPL-1.0.OliPof
CPLD-8
Sorry - just re-read this - doh! Sorry to have wasted your time
HTH
Matt

ATT tylt unlock problem(a)!

Hey,
Any help would be appriciated...
I've completed all 3 steps to unlock my htc to work with other sims, after completing step 3, the screen went blank and afterwards just scrambled white pixles...
I cant get the sync icon to go green, not to log in to the wm inreface, so i'm kinda jammed.
I CAN reset and goto the 3 color screen, which displays:
Security Unlocked
KAIS1*0 MFG
SPL-1.0.01Pof
CPLD-8
Any ideas?
Which unlocker were you using? Try using KaiserUnlocker found here....http://forum.xda-developers.com/showthread.php?t=375583
Run the app and click Flash Hard-SPL
After this step your phone needs to be on meaning NOT in the Tri-Color screen.
Next run Unlock Radio
Now run Unlocker (again phone needs to be on NOT in Tri-Color screen to work) FOLLOW the steps on phone screen (instructions are also given on above forum)
**Running the Radio Unlocker will change your Radio so it can UNLOCK, after you are done you will need to flash back a new Radio**

Trying to Unlock MDA Vario III with HTC_Hermes_SIM_CID_Unlock_v3a

@All
i'm trying to unlock one MDA Vario III as its mentioned that its supported by HTC_Hermes_SIM_CID_Unlock_v3a i've done everything HARD SPL is successfull but still i can't unlock it always getting error when try to update it. always get error on 7% which is shown in picture.
picture is attached for the reference.
on boot loader screen i can see following Information with Tri Color
KAIS130 MFG
SPL-1.0.OliPof
CPLD-8
and when i power on phone normally i can see following information.
R 1.27.12.32
G 22.45.88.07H
D 1.56.00.00
Take Care
ENJOY
The Vario III is technically a Kaiser. So I would suggest trying to Kaiser Unlocker instead. Just to be sure.
JimmyMcGee said:
The Vario III is technically a Kaiser. So I would suggest trying to Kaiser Unlocker instead. Just to be sure.
Click to expand...
Click to collapse
thanks for your TIP , unlocked successfully.
Take Care
ENJOY

[Q] HTC HD7 half briked >> USB enter host mode after update[Q]

Good evening,
I "half-bricked" my HD7 ...
since it has two updated via zune
by chance, I try the bootloader
miracle and the screen with 3 color bands
and with 4 or 5 lines of writing, but ke I do not have time to read very quickly because there comes a light gray screen with a blue print "enter usb host mode" ...
So here my question what can I do now to install a Rom mango unlocked without re stupidity
Finally, already is that possible??
Thank you very much for your help
as I was comfortable with wp wm as I am lost
titeloo said:
Good evening,
I "half-bricked" my HD7 ...
since it has two updated via zune
by chance, I try the bootloader
miracle and the screen with 3 color bands
and with 4 or 5 lines of writing, but ke I do not have time to read very quickly because there comes a light gray screen with a blue print "enter usb host mode" ...
So here my question what can I do now to install a Rom mango unlocked without re stupidity
Finally, already is that possible??
Thank you very much for your help
as I was comfortable with wp wm as I am lost
Click to expand...
Click to collapse
Whats your current SPL? (Holding down the Volume (-) + Power)
THANK YOU VERY MUTCH FOR YOUR HELP
in the screnn it's write
PD29100 SS-BC (4k)
SPL-5.10.2250.0(132968) mng
MicroP(LED) 0x07
TOUCH S1(v1.8,#1624)
SD SANDISK 7580MB
Partition Info-v211v413
F400
titeloo said:
THALK YOU VERY MUTCH FOR YOUR HELP
in the screnn it's write
PD29100 SS-BC (4k)
SPL-5.10.2250.0(132968) mng
MicroP(LED) 0x07
TOUCH S1(v1.8,#1624)
SD SANDISK 7580MB
Partition Info-v211v413
F400
Click to expand...
Click to collapse
if you can read all that your phone isn't bricked.
and it isn't half bricked to.
it is just updated to spl 5.10 and you can't use the H/R spl from cotulla on this (so don't try that because then you will get a half bricked phone)
there are some tut's here on xda how to roll back to a lower spl.
here is a link to a tut to roll back:
http://forum.xda-developers.com/showthread.php?t=1371073
really thank you for your help again.
before i do the update it's was only one line written
because i have do a mistake trying install hspl
but after two update via zune, the SPLscreen is like i've written before
now i haven't other solution to downgrade the spl ?
because i just want to install advanced config , and that look very complicate to downgrad spl
( sorry for my bad and english )
Moved to HTC HD7 General
This is a device specific question, not in the development section please.
please refer to the read before posting stcky for guidelines.
Take it easy
O_G

Kaiser 120 stuck in logo, don´t have hard spl, please i need your help

I have in my hands a KAISER 120, stuck in logo and don´t have hard spl maked.
Somebody else brought me that HTC in that state.
that is the info, baterry back
P/N 99HCY196-00
S/N HT844GA02102 T02
Info showed in logo:
R 1.65.29.21
G 25.100.40.08H
D 3.34.00.00
Info in ticolor mode:
KAIS120
SPL-3.34.0000
CPLD-8
Info mtty:
Cmd>info 0
Platform Model ID:KAIS12000
Platform HW Board ID:31, PVT1
Cmd>info 2
HTCSBSTAR301‹§¸BHTCE
Cmd>getdevinfo
GetDevInfo: Get CID OK
HTCSKAIS1200HTCE
Cmd>
Thats the rom version that i need: 3.34.524.0 esn FECHA:09/02/08
Please i need your help to fix that htc Kaiser bricked.
thanks in advance
try with this rom http://shipped-roms.com/download.php?category=windows%20mobile&model=Kaiser&file=RUU_Kaiser_HTC_SPA_3.29.412.0_radio_sign_25.83.40.02_1.65.17.56_Ship.exe

Categories

Resources