Database Develop

HELP!!! phone not working

I REALLY NEED HELP...
i was updating the rom to 2.21 and i guess i accidently closed the program.. sooo now my phone turns on to this screen.. it shows 3 colors.. i can not do anything..
i really need help.. what can i do to go back?

Ok, there's a chance that you just turned your phone into a nice little paperweight however, I recommend trying two things. First, try to perform a hard reset by following these steps:
1: Press and hold both the Comm Mannager Button and the Voice Command Button
2: While keeping those two buttons pressed, press the Reset Button with your stylus
3: After about a second you will be prompted for confirmation. Press the Talk Button to confirm
If that fails, try performing the ROM upgrade again. If THAT fails...well either my assumption is correct or you're gonna need someone more proficient than me to help you ^_^

i tried doing that.. that didnt work..
when you try to install the rom again.. the phone has to be connected with active sync.. and right now its not.. but if u look at the screen on the phone.. it says usb.. but it doesnt connect..
so idk what to do now..
i have another mda..
this one has the original ROM and it works.. is there anything i can do?
please help

harut9161 said:
i tried doing that.. that didnt work..
when you try to install the rom again.. the phone has to be connected with active sync.. and right now its not.. but if u look at the screen on the phone.. it says usb.. but it doesnt connect..
so idk what to do now..
i have another mda..
this one has the original ROM and it works.. is there anything i can do?
please help
Click to expand...
Click to collapse
If you have the bootloader screen(rainbow) it should be retrievable.
Just to be sure you enter the bootloader screen hold camera button and turn on.
The device should be able to connect to your pc, but not by activesync.
If it wont try disabling any firewalls or antiviral on the pc and try again.
Once the pc recognizes your device - run the rom upgrade again.

Fan-freaking-tastic!!!!
Thanks meschle !!!!
I had loaded a cingular rom onto a tmobile thinking all HTC roms should work alike (i know idiot sign is already on my forehead) and the phone was working but very slowly and sync did not work...
I checked and I could get to the bootloader screen (rainbow) as you suggested and then was able to load the original firmware just fine... Phew.. Saved my having to explain a $500 brick to folks.. lol
I have a question on this however, if I want to upgrade the radio or something other than T-MOBILE rom.. what do I need to look for to be sure it will work on my T-MOBILE ?
Cheers
and Thanks

Who wants to try a new way to go out from stuck splash screen?

Hi I have a problem trying to exit from bootloader a PDA's friend, so how can I get to work the mtty?
Sometimes i gain exit with mtty of bootloader screen just kill usb conn in activesyng letthe device in bootloader an conect... select USB port click on OK button and then task 28 erase DOC Chip and then task 28 55aa ready to reflash the same rom that has the problem.
but now i try it on my device an aku3 ipl spl 3.08... on bootloader in a PC Vaio with XP home SP3and....
it say invalid comand
so the dir is CMD
NOT USB
how can i get usb on the dir?
Any body knows?
i had the mtty .01, 2.11 and 1.42 and no one works
any idea?

SADNESS!!!!!!!!!!!!!!!!!
Somebody stole my wizard last night i was waiting for the BUS and two guys atacks me with a knife, they took my Wizard and my money. Again... and in some part i saw somebody called INSANAVACA saying that when the Mtty shows CMD we can put "format" and then choose the A character or B character... one of those options is the OS the other one... Neither him knows jeje and dont remember which one to chose... it starts to clean the DOC Chip.
It maybe works... i cant test it so if anyone can do it please, answer this maybe it works and we can get out of the Splash screens and bootloader stucks.
A long time ago I did this steps but the mtty shows me USB. full charge your batt, remove your SD and SIM card... enter in bootloaders... uncheck the activesync allow USB conection and kill Wcescomm.exe in Win XP taskmanager plug your device to usb, open mtty in all the places works even in the desktop... select USB in the drop menu... a blank screen will appear hit enter if it shows USB your done then... type:
task 28 (hit enter)
--it starts tho the cleaning--- done...
task 28 55aa (it works again in the same thing)
Close the mtty dont unplug your device and reflash it with the stock rom 2.26 Tmobile if you unplug the device you can try to plug it again but in the same port... (but my device is SuperCID unlocked) then goes to the custom ROM.
Maybe the "format" can works if in blank screen shows CMD... try it and let us know what happend ok?
I use the 1.42 Version.

hey thanks for the reply on my thread.maybe we can discuss my problem here.
my wizard is stuck at 2nd splash (the one with the ipl,spl,gsm and os versions)
falshing another rom do not fix the problem. ive even downgraded to several WM5 roms like wizard love, button rom and xda-mini s launcher.
i have a g3 cid sim unlocked wizard.
then lately i noticed, after attempting another manual hard reset, it says formatting failed. so maybe i need to force reset it using a pc. but wizard service tool wont work coz it will only work when synced on the pc.
can mtty forceley reset (hard reset) my wizard? how should i do it? what are the commands? thanks

i've read a thread and read meistrinis reply where he pointed out this thread:
http://forum.xda-developers.com/showthread.php?t=276963
hope this one works for me

lets check it!
dielo said:
i've read a thread and read meistrinis reply where he pointed out this thread:
http://forum.xda-developers.com/showthread.php?t=276963
hope this one works for me
Click to expand...
Click to collapse
I have redirect to a Universal commands for mtty but i cant be for sure if all works for wizards!
So download the mtty 1.42
Unplug your MiniSD card
Put your Wizard in bootloader mode
Kill the wcescomm or put in activesync not allow usb conections
then open the mtty
in ports or conectios you will see
com1
com2
com3
IRDA
USB
More or less I dont know deppending how many ports does your pc have.
choose USB
Be sure that your batt is almost 80% a 100% will be great but with 80% is fine
After choose USB dont move anymore and click ok... or connect something like that.
A blank white screen appear....
Then hit enter if it shows USB> type exactly this:
task 28
(it will work on something like clean the DOC CHIP at the end will show again USB>)
then type exactly this:
task 28 55aa
It will work again on something and
It will prepare the DOC Chip for the OS (FORMAT)
The device stills on bootloader so close the mtty dont unplug the device and downgrade to an original ROM WM5
These are the steps if the MTTY shows USB>
Select the USB port
hit enter in white screen
If it shows CMD>
type in the white screen after the CMD>
format
It will shows you what to choose option A or OPTION B
Here is the problem... Which one we need to choose...
and reflash an original ROM.
Tell us what happends please.
I HAVE MORE COMANDS but for G4 AND WHY IT WONT SHOWS USB!!!!!
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader

+ Que PPC said:
I have redirect to a Universal commands for mtty but i cant be for sure if all works for wizards!
So download the mtty 1.42
Unplug your MiniSD card
Put your Wizard in bootloader mode
Kill the wcescomm or put in activesync not allow usb conections
then open the mtty
in ports or conectios you will see
com1
com2
com3
IRDA
USB
More or less I dont know deppending how many ports does your pc have.
choose USB
Be sure that your batt is almost 80% a 100% will be great but with 80% is fine
After choose USB dont move anymore and click ok... or connect something like that.
A blank white screen appear....
Then hit enter if it shows USB> type exactly this:
task 28
(it will work on something like clean the DOC CHIP at the end will show again USB>)
then type exactly this:
task 28 55aa
It will work again on something and
It will prepare the DOC Chip for the OS (FORMAT)
The device stills on bootloader so close the mtty dont unplug the device and downgrade to an original ROM WM5
These are the steps if the MTTY shows USB>
Select the USB port
hit enter in white screen
If it shows CMD>
type in the white screen after the CMD>
format
It will shows you what to choose option A or OPTION B
Here is the problem... Which one we need to choose...
and reflash an original ROM.
Tell us what happends please.
I HAVE MORE COMANDS but for G4 AND WHY IT WONT SHOWS USB!!!!!
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
Click to expand...
Click to collapse
hey thanks, though drug_store's method worked for me and now my wizard is working and i have update 3 for my rom. still a big thanks to you for the starting point on where to look at.

Congrats Men!!!!
dielo said:
hey thanks, though drug_store's method worked for me and now my wizard is working and i have update 3 for my rom. still a big thanks to you for the starting point on where to look at.
Click to expand...
Click to collapse
Very good men!!! you're welcome.
Even if this method still hasn't been proved.

Here's a reason i'm taking Rom's out from Stickies.
So there's space for the important things like this on..
Let's face it sometimes a new thread on Bootfreezes and Bricks is more useful then an old one that people get discouraged by, because of it's length.
Made this one Sticky.

Noonski said:
Here's a reason i'm taking Rom's out from Stickies.
So there's space for the important things like this on..
Let's face it sometimes a new thread on Bootfreezes and Bricks is more useful then an old one that people get discouraged by, because of it's length.
Made this one Sticky.
Click to expand...
Click to collapse
great. you're right. thread like this should be stickied.

Wow
Stickie!!! hahaha so glad too see it thanks but.... is not prooved yet... so does anybody wants to try... damn if i had my wizard ...

It gets more renewed Attention to the most important problem.

Maybe....
You've got right!!!
I will make a deal With Tvaril to buy him his wizard but i need more info about to receive packages World wide. and the way to pay jeje...
I hope it can be truth in an easy way.

in the mtty, when i pres enter it getc CMD, when i type format it gets unavailable comand, so im still stuck on the align screen some other help

Man it sucks!!!!
But in sync screen?
Damn this is new huh!
I dont know what else can we do...
does you try to reflash again an originla ROM?
maybe ayou are in troubles cause your battery is too low...

display damage
i just find out that i damaged the lcd with the f****** glue. i was trying to glue the mask and the glue went on the LCD so i f***** up.
by the way the battery was full recharged, and everything was done like you said.

it sound very bad men!!!!!!
Does the display works? or it has issues?
maybe you can find a display.. so sorry to heard that.

Thank you!
thanks for this mate i was using mtty in vista using the compatiblity patch...
i downloaded all the 4 things who know they may be useful at some point of time for me when i need to do stuff.
Have a good day!
Regards,
Sam

good to hear it... but
why dont post the compatibility patch for all members?
come on share it here men!

I download mtty a while back, you know, just in case. Wellllllll, just in case happened yesterday. Mtty made it easy as pie and quick, too. Now, baby's fine and reflashed and happy again!

my friend has the same problem as this, his wizard g4 stuck on splashscreen when he flash love_rom using How to flash a new ROM to your Wizard... a little tutorial!. His problem was solved if he flash rom using this manual (I'm sorry for czech link, english version by Google translator)

Diamond stoods at bootloader screen

After I get out my diamond from my pc and than turned off it cannot start, it stoods on screen when it shows me version of my radio and ROM. I know that I have to do hard-reset but i dont want to, because i were so dumb that I dont backed up my mdata and programs which Ihave installed in Memory. Is there any chance to turn it on without the hard-reset???
Thx in advance.

betacheer said:
After I get out my diamond from my pc and than turned off it cannot start, it stoods on screen when it shows me version of my radio and ROM. I know that I have to do hard-reset but i dont want to, because i were so dumb that I dont backed up my mdata and programs which Ihave installed in Memory. Is there any chance to turn it on without the hard-reset???
Thx in advance.
Click to expand...
Click to collapse
do you mean bootloader (Tri-Coloured Sceen) Or the splash screen (Black Screen with touch diamond on it)?
I suggest you do a hard reset, and check this thread on how to easly back up ur programs, settings and manila config for future use using SASHIMI
http://forum.xda-developers.com/showthread.php?t=538513

Stuck in Bootloader screen
Whlie trying to upgrade the ROM on my Touch Diamond something happend so i got an error and the upgrade stopped. Now i cant continue the upgrade becouse my pc wont recognize the phone when i connect it with the usb-cabel. When i try to run the upgrade again i just get an error saying that there is something wrong with the connection.
I have tried hard reset but nothing works.
Hope someone can help me with this problem.
Thanks
/Kenneth

KenOslo said:
Whlie trying to upgrade the ROM on my Touch Diamond something happend so i got an error and the upgrade stopped. Now i cant continue the upgrade becouse my pc wont recognize the phone when i connect it with the usb-cabel. When i try to run the upgrade again i just get an error saying that there is something wrong with the connection.
I have tried hard reset but nothing works.
Hope someone can help me with this problem.
Thanks
/Kenneth
Click to expand...
Click to collapse
i think I am in same situation. phone is bricked :/

I dont think your phone is bricked, put your phone into bootloaded mode, connect phone to pc and flash the nbh file using CustomRUU. That should fix things

Dom1n8tr1x said:
I dont think your phone is bricked, put your phone into bootloaded mode, connect phone to pc and flash the nbh file using CustomRUU. That should fix things
Click to expand...
Click to collapse
each bootloader i have tried using the different hard spl version gets as far as the progress bar but fails at 0% with 262 connection error. tried about 6 different hard spl, signed unsigned olinex, customRUU. each of them all fail at 0% of progress bar.
will try it again today.
sorry betacheer for the hijack, but hope this helps you out in some way too.

Hspl error check THE picS

HELLO
i'm going crzay from the hspl
the auto flash dosn't work
and the manual flash file when i run it the device is lag
so i get into the bootloader by pressing volum down and power then realese
and i start the manul flahs then here is the 7 pictures i put it in zip file cu they more than 4 file
hope we fix the proplem
plz
plz
plz
help

SYRIAN4E said:
HELLO
i'm going crzay from the hspl
the auto flash dosn't work
and the manual flash file when i run it the device is lag
so i get into the bootloader by pressing volum down and power then realese
and i start the manul flahs then here is the 7 pictures i put it in zip file cu they more than 4 file
hope we fix the proplem
plz
plz
plz
help
Click to expand...
Click to collapse
Might have been more help asking in the hspl thread but nevermind . Try a different cable (most mini usb cables will do)

SYRIAN4E said:
HELLO
i'm going crzay from the hspl
the auto flash dosn't work
and the manual flash file when i run it the device is lag
so i get into the bootloader by pressing volum down and power then realese
and i start the manul flahs then here is the 7 pictures i put it in zip file cu they more than 4 file
hope we fix the proplem
plz
plz
plz
help
Click to expand...
Click to collapse
no need to go crazy, this can be fixed.
you shouldn't enter the bootloader yourself, it won't flash that way.
what error did it say in automatic mode?

syrian
tha messeage talk about turning off my firewall
and the server is off
and this is my first hspl

SYRIAN4E said:
tha messeage talk about turning off my firewall
and the server is off
and this is my first hspl
Click to expand...
Click to collapse
ok did you turn firewall off? turn proxy off too, if you have a proxy.
if that doesn't sort it, I can still help you if you message us via this link: http://support.htc-unlocks.com/

syrian
i change the usb and disable the proxy and turn off all my firewall and antivirus
i think the proplem from something lagging from the hspl software
cuz i enter the bootloader and i start manual flash and it's respond and show to me the update button and i press it and tell my software version and if i wanna change to oilnex version and i press it and show to me the percentage image on the pc and in the phone then i wait then nothing happend

SYRIAN4E said:
i change the usb and disable the proxy and turn off all my firewall and antivirus
i think the proplem from something lagging from the hspl software
cuz i enter the bootloader and i start manual flash and it's respond and show to me the update button and i press it and tell my software version and if i wanna change to oilnex version and i press it and show to me the percentage image on the pc and in the phone then i wait then nothing happend
Click to expand...
Click to collapse
you shouldn't enter the bootloader like that, the flash won't work that way.
I replied to your priv. message

syrian
is there any hope CHECK THE PICTURE
1st - the cable is work well cuz i update the device with it from the offical htc website
2nd- the picx
3rd- i run the EXE in the device and it SHOW TO ME THIS MESSAGE : Lic OK
4TH- I START THE manual FLASH
2nd- more INFO
RED LINE : TOPA100 32M
SPL-2.51.0000
MicroP-Topaz (LED) V10
TURBO HW/TURBO SW
GREEN LINE : TP MFG DATA
502,547 170,876
173,200 834,210
828,869 Calibrated
BLUE LINE : E M P T Y
WHITE LINE : U S B

SYRIAN4E said:
is there any hope CHECK THE PICTURE
1st - the cable is work well cuz i update the device with it from the offical htc website
2nd- the picx
3rd- i run the EXE in the device and it SHOW TO ME THIS MESSAGE : Lic OK
4TH- I START THE manual FLASH
2nd- more INFO
RED LINE : TOPA100 32M
SPL-2.51.0000
MicroP-Topaz (LED) V10
TURBO HW/TURBO SW
GREEN LINE : TP MFG DATA
502,547 170,876
173,200 834,210
828,869 Calibrated
BLUE LINE : E M P T Y
WHITE LINE : U S B
Click to expand...
Click to collapse
the screenshots are very helpful in seeing what your problem is.
ok, after 3rd step now try copying Manual SSPL exe (link: http://forum.xda-developers.com/attachment.php?attachmentid=232407&d=1254155476) on the phone, run it, it should then show SSPL screen on the phone. then use the Manual flash mode on the PC. let me know if it works that way

syrian
the device get LAG when i launch the manual sspl and i start manual flash even whene it's lag
and here is the picture

SYRIAN4E said:
the device get LAG when i launch the manual sspl and i start manual flash even whene it's lag
and here is the picture
Click to expand...
Click to collapse
what do you see on the phone screen at this point?

syrian
nothing just the file maneger when i launch the manual sspl cuz the device lag

SYRIAN4E said:
nothing just the file maneger when i launch the manual sspl cuz the device lag
Click to expand...
Click to collapse
ok you did step "3rd- i run the EXE in the device and it SHOW TO ME THIS MESSAGE : Lic OK"
and then you run the manual sspl EXE on the phone, it still lags ?
I'm asking to make sure you did not do a hard reset or anything (I mean, don't do hard reset)

syrian
i just did it in ever way that you can imagine
and i think that the manual is the proplem i'm sure
is ther any hspl type haha we can use

SYRIAN4E said:
i just did it in ever way that you can imagine
and i think that the manual is the proplem i'm sure
is ther any hspl type haha we can use
Click to expand...
Click to collapse
ok one last check.. send me a screenshot of your phone showing the IMEI to make sure it's OK.
but do not post the screenshot publicly, send it in private message.

syrian
come on xda help me lol

SYRIAN4E said:
come on xda help me lol
Click to expand...
Click to collapse
alright I realized that the second file was the wrong version. I sent you the correct file in PM, let me know if it worked

syrian
OMG it's WOrk good
thanks a LOT for you
i own you
LOT
LOOK how much time it take to fix this proplem LOL
now i have another proplem and it is if you won't
is how to download the duty or energy rom cuz they are upload on HOTFILE and RAPIDSHARE LOL
and i thanks for the second time and love to know what was the prolem
SYRIAN4E

SYRIAN4E said:
OMG it's WOrk good
thanks a LOT for you
i own you
LOT
LOOK how much time it take to fix this proplem LOL
now i have another proplem and it is if you won't
is how to download the duty or energy rom cuz they are upload on HOTFILE and RAPIDSHARE LOL
and i thanks for the second time and love to know what was the prolem
SYRIAN4E
Click to expand...
Click to collapse
glad to help. as I said, the manual SSPL in the thread was the wrong version. I forgot to update it at one point, will add it in the thread now. (most people can just go and use automatic mode so nobody noticed there was an issue with the file.)

Hi all
I really need some help please!!
I think I have read and searched and tried steps by step all the posts and threads on this, none of them work for me,
Ive flashed my HD2 & TD2 with HSPL, radios and roms many times in the past. I have a stock rom on my TD2, (havent flashed a cooked one yet but did on my HD2 and worked great),
the problem is when I try flash anything, (HSPL,Radio's and Roms)
I connect with WMDC on windows ultimate 64x and go through all the steps, the phone disconnects from WMDC when loading the tri-color screen, and installs the HTC sync drivers fine, and then (my problem) it hangs on 0%. this happens regardless of what I'm flashing after a while brings up the communication errors 208 & 260. this doesnt have any effect on the software HSPL or radio as a soft reset returns back to the homescreen just fine. I am running HSPL 1.8.3. , radio 4.49.25.17 and a shiped stock wm 6.5.
This is what Ive tried so far:
I have used 3 different micro USB cables,
updated my .net fx to 4.1
I have tried different Ruu's such as custom Ruu, Ruu from topaz, Ruu, supplied with Hspl, flashes center and KaiserCustomRUU.exe and a few others.
Ive tried the white screen fix many times. including the SDA unlocker and stuff.
I ve tried manual and automatic.
tried entering the the Tri-color screen manually and via the Ruu.
I tried different computers and different operating systems (W7ultimate and XP 32Bit and 64Bit)
tried active sync WMDC 6.0 and 6.1
Ive removed the SD card and sim and have tried flight mode
Restarted pc's mobile any reinstalled WMDC many times.
Ive tried renaming to the HSPL, radio and Rom to TOPAIMG.nbh , put 1 by 1 on formated fat32 SD card, run from Tri-color menu. all of them just hang on
loading....
Have tried mixing and matching Ruu's with HSPL's, Roms And radios and everything else i can think of, after 18 hours of this I am fed up and decided i need some help
Thanx in advance
ok
i have now download the official RUU_Topaz_S2_HTC_WWE-AFK_2.53.421.3_Radio_Signed_Topaz_61.44etc.25.35_4 .49.25.91_Ship.exe Rom
and it worked with no problems.
it updated my HSPL from 1.83 to 2.51 and radio version to 4.49.25.91 which was exactly what i was going for.
The problem now is that i still cant change my HSPL, RADIO or flash a custom Rom which is what I need. it hangs on 0% and now gives me a 262 error which states that:
ERROR [262] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process. If this happens, you can just soft reset the device and run RUU again. The update process will then continue. At this stage the rom on the device is incomplete and it will not boot back up into Windows. You will need to place it into the bootloader to continue.
which is not true as if a reboot it doesn't continue the update and just returns to the home screen as normal
help?

guys i need help with hard spl :(

ok,i tried the sd-method.still nothing.it says no image file.i tried the pc method,it gives me a error message.i think pc method doesnt work because i dont have NET-framework.and i download the F****** net framework and i want to install it and it says error!im pissed right now!the phone is driving me crazy!so help me before i smash it and throw it in the wall

xperiauser132 said:
ok,i tried the sd-method.still nothing.it says no image file.i tried the pc method,it gives me a error message.i think pc method doesnt work because i dont have NET-framework.and i download the F****** net framework and i want to install it and it says error!im pissed right now!the phone is driving me crazy!so help me before i smash it and throw it in the wall
Click to expand...
Click to collapse
try to make manual synch then install netframework, for me SD method never worked, i always flash with pc method,
and last thing: I actually use Dynamics rom, is the best I tried with NRG and x826
also try deleting net framework from pc than relaunch for making it install on pc and on phone together (that worked for me)

i don't think flashing hardspl over stockspl via sdcard works. hardspl 0.72 used a special exe, not suitable for everything else.
flashing hardspl 0.78 over hardspl 0.72 via sd works fine. and no, stockspl 0.78 doesn't make it any harder, i got it back from service 2 times with it.
but i already told you, you need a fully working connection with activesync first for usb-flash to work. (device center from Vista onwards), you might need to search for usb-drivers for x1 first (which also allow the pc recognize the phone if you attach it in bootloader-mode).
iirc, after starting flash-process with winmo running, there was a popup on stockrom if you really want to let some exe reboot the phone (to enter bootloader).

yes you need to fully synchronize with a server or pc

server doesn't have to do anything with it.
and no, he doesn't need to do a full sync with pc. but he needs to be able to do that.

caliban2 said:
server doesn't have to do anything with it.
and no, he doesn't need to do a full sync with pc. but he needs to be able to do that.
Click to expand...
Click to collapse
Yes but usually I make a synch to be sure that its all good =)