Related
Hi all,
I tried to upgrade my MDA compact II (HTC Charmer) to WM6, but during the first step, downgrading to the "no vendor" version I made a mistake. A used a wrong version, it was for Prophet. After the final reboot, the device froze in the splashscreen "T-Mobile". After that I tried to do exactly the same with a "Charmer" version, but it didn't help me, the situation was the same.
However, now I'm able to flash successfully only the last vendor provided ROM update "RUU_Compact_ll_2060227_20602110_021921_T-MobileUK_Ship.exe", but it doesn't help me anyway, my Charmer is still freezing in the splashscreen. I tried to downgrade it , but the application gives the following error: "UPGRADE ONLY". When I try to make a hard-reset, and after that to confirm the factory settings by pressing "Yes" (green) button, the result is "Format FAT partition" and then "format is failed".
Only the bootloader is working now as well as the battery charging. Please, help me to turn back to the life my Charmer!
And one additional question: can I perform a CID unlocking just by ROM-flashing or the device must be fully operable?
Flash this:
http://rapidshare.com/files/41754719/RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe.html
After that, you should be able to make hard reset. If you succeed, flash "RUU_Compact_ll_2060227_20602110_021921_T-MobileUK_Ship.exe" - that.
Hello there,
I am a new use an recently got an MDA PM200. I am in exactly the same situation as petrun. I have tried the flash suggested by vlodeck but it doesn't work, saying incorrect vendor ID (I guess that's because it's for a Prophet?).
What should I do next...?
Thanks.
OK, I succeed with a little progress. Many thanks to vlodeck, I will try to explain what happend...
I successfully flashed my Charmer with this Prophet ROM:
RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe
Full link:
http://rapidshare.com/files/41754719/RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe.html
But it was possible only by using this "No ID" update application, not original one, maybe because my device is still locked:
Full link:
http://www.windowsceportal.hu/tartalom/programok/htc_charmer_upgradeut_noid.zip
After that I succeed to format the FAT partition (finally ). But I cannot after all to flash the latest official MDA compact II firmware. There is two possible events, which I experienced:
1. When I try to use the original flashing application, I get the following response: "UPGRADE ONLY".
2. When I try to flash the official MDA compact II ROM, but through the "No ID" application, I get "INVALID COMMAND".
Just for explication, now my device cannot boot, it freezes in the splashscreen (it is Qtek now, not T_Mobile...) and the following versions could be read:
IPL 2.06
SPL 2.20.0000
GSM 02.47.21
OS 2.20.7.34
So, how I can do that? What should I do further? I would like to unlock my Charmer, but should I firstly make it operable?
Thanks in advance for your help, guys!
By the way, all described above I tried sevetal times with the same result.
The other thing is that... all links about the CID unlocking downloads, which I found here are no longer active. Any alternatives?
Rise from the dead!
Incredibly, but it's a fact! After successfull FAT formating I probably didn't wait long enough. Today I turned on my Charmer and several seconds after the splashscreen "QTEK" it successffully booted in WM5, performed all settings and finally started to work!
It's GSM module works, the Bluetooth works, I am able to start different applications. Just the camera does not work. And the most strange thing for me is that this ROM was for Prophet, not for Charmer
So, after all, how to proceed to upgrade to WM6? Now the bootloader is above ver.2.
Should I firstly flash it with proper ROM (for Charmer) or it's not necessary?
Should I unlock it as is now (Prophet ROM)?
Vlodeck, I rely mostly on you, since the WM6 with Touch FLO is your creation.
Thanks!
You dont have to CID unlock. Just flash that WWE T-mobile WM5 AKU2 for Charmer. Good luck.
Maybe I am boring, but steel need an advice: I cannot flash "WWE T-mobile WM5 AKU2".
1. The original RUU gives me "UPGRADE ONLY", maybe because my SPL after flashing the Prophet ROM is 2.20
2. This "NO ID RUU":
http://www.windowsceportal.hu/tartalom/programok/htc_charmer_upgradeut_noid.zip
reaches 2% and gives "INVALID COMMAND", after that - only bootloader screen.
3. This "NO ID RUU":
http://forum.xda-developers.com/attachment.php?attachmentid=42657&d=1183226200
cannot open the nk.nbf image (but works with other images), I don't know why.
What is the solution? Any ideas? Maybe some tool to downgrade the SPL to ver.1? I tried (it perhaps was bad idea)"RUU_Charmer_1120223_11202110_11220_T-MobileUK_Ship" and IPL became 1.12, but SPL remained 2.20... and Charmer didn't boot after that. After flashing the Prophet ROM it works again and IPL is 1.12, SPL is 2.20
In brief... how to flash successfully the last Charmer ROM?
If you cant flash the AKU 2 charmer rom, then go for AKU3.3 rom (can be german, that doesnt matter). Once done that, flash wm6.
Success
Yeah! Thanks to vlodeck now everitging is all right! I flashed the original German AKU3.3 ROM by using this RUU:
http://forum.xda-developers.com/attachment.php?attachmentid=42657&d=1183226200
(The original one gives "INVALID VENDER ID", of course, in German ) After that - successfully upgrade to WM6 TouchFLO.
Briefly:
1. First try to flashing WM6 - crash! The reason: old bootloader version (IPL/SPL = 1.12).
2. Flashing the Prophet ROM - success for FAT formatting. The Charmer turned back to life.
3. Flashing the German AKU3.3 ROM from T-Mobile, but through the No ID RUU.
4. Upgrade to WM6 TouchFLO by vlodeck. At the begining I reached the same problem, as described here:
http://forum.xda-developers.com/showthread.php?t=331717
but after istalling cert_spcs.cab and enablerapi.cab in my device I succeed to finish the process.
Thanks vlodeck, good job! This ROM is really amazing!
petrun said:
Yeah! Thanks to vlodeck now everitging is all right! I flashed the original German AKU3.3 ROM by using this RUU:
http://forum.xda-developers.com/attachment.php?attachmentid=42657&d=1183226200
(The original one gives "INVALID VENDER ID", of course, in German ) After that - successfully upgrade to WM6 TouchFLO.
Briefly:
1. First try to flashing WM6 - crash! The reason: old bootloader version (IPL/SPL = 1.12).
2. Flashing the Prophet ROM - success for FAT formatting. The Charmer turned back to life.
3. Flashing the German AKU3.3 ROM from T-Mobile, but through the No ID RUU.
4. Upgrade to WM6 TouchFLO by vlodeck. At the begining I reached the same problem, as described here:
http://forum.xda-developers.com/showthread.php?t=331717
but after istalling cert_spcs.cab and enablerapi.cab in my device I succeed to finish the process.
Thanks vlodeck, good job! This ROM is really amazing!
Click to expand...
Click to collapse
WHERE I CAN GET BOUTH FILES cert_spcs.cab and enablerapi.cab
AND WHAT VIRSION OF PROPHET ROM SEND ME WORKING LINK THX DEAR
Charmer Stuck At Splash Screen
CHARMER STUCK AT SPLASH SCREEN
--------------------------------------------------------------------------------
I HAVE A MDA COMPACTII ''MADE IN TIWAN'' I WITCH WM5 I WANT TO UPGRADE IN TO WM6 SO I UPGRADE THIS WM6 TouchFLO Charmer WM6 ver. 2.1 FINAL by vlodeck AT THIS HOME PAGE http://forum.xda-developers.com/show...harmer+cert_sp... AFTER THIS I HARD RESET MY MDA C2 ITA ON BUT THE LANGUAGE IS NOT ENGLISH I CANNOT UNDERSTAND ....
SO I CAN REFLASH IT WITH THIS ROM Charmer_Touch_GER_Beta_2.7 .. AFTER FLASHING COMPLETE I SOFT RESET MY MOBILE.
SO MY MOBILE STUCK ON SPLASH SCREEEN ONLY T-MOBILE IS SHOW
MY MOBILE DETAIL IS AS UNDER
IPL 2.06 .0001
SPL 2.06 .0001
GSM 02.19.21
OS 4.0.0.0
PLZ DEAR SIR WHAT IS SOLUTION OF MY MDA C2
MDA2 CANNOT CONNECT WITH ACTIVE SYNC
Of course it cannot connect with ActiveSync, the device doesn't boot. One certain solution for bricked Charmer is Prophet ROM:
RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe
Use this link:
http://rapidshare.com/files/41754719/RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe.html
In order to flash this, you should enter the bootloader, without using the ActiveSync. After that try to perform a hard reset, you probably will succeed to format the FAT partition.
if you cannot connect the pda to pc HOW CAN U PUT THE ABOVE PROPHET RUU ON CUREENT?
I have a charmer and I was trying to update to wm6. I can´t because the ipl is 1.12. I updated rom to german aku 3.3. But I can´t hard reset. format error. I´m trying to put prophet rom to format it, but when I send the prophet rom, it always give me an error at 95%. error 326 - this nbf file cannot be used fo your pda phone. please check your nbf file. the aku3.3 rom flashes ok. any idea?? I try tu send a radio rom. after that is the same. 95%error. please help. I can´t bring my charmerback to life.
Hello together,
I have the same problem like _mestre_.
I updated from T-Mobile AKU 3.3 GER to WM6 and flashed back to WM5 without problems, but when flashing again to WM6 from vlodeck my charmer didn't boot anymore and had that "Format is failed"-problem when making a hard reset. I could not recover my device until now with the method explained in this thread cause of the problems "error 326 - This nbf file cannot be used for your pda phone". So the Prophet Rom does not seem to work with boot loader 3.x. Has anyone any idea? Please help! Thank you very much in advance!
Yallah said:
Hello together,
I have the same problem like _mestre_.
I updated from T-Mobile AKU 3.3 GER to WM6 and flashed back to WM5 without problems, but when flashing again to WM6 from vlodeck my charmer didn't boot anymore and had that "Format is failed"-problem when making a hard reset. I could not recover my device until now with the method explained in this thread cause of the problems "error 326 - This nbf file cannot be used for your pda phone". So the Prophet Rom does not seem to work with boot loader 3.x. Has anyone any idea? Please help! Thank you very much in advance!
Click to expand...
Click to collapse
same problem here... any suggestions or is my charmer bricked?
Hi guys,
this is one of my first post here but I read you everytime. So, the problem now is: my P3600 don't want to flash with any rom.
I've just take it back from assistance for to change the black cover (2nd time...) and when I want to flash, as before I was given to the assistence, with udK 6.1 rom it don't want to flash with any other roms!!
I've now download the Lite version of udK 6.1 and install it but when I've discovered that I prefer the full version that's start the never ending story: I tryed to flash with Full version 2 or 3 time already, the installation goes to 100% but when it restart (should it restart not power off?!?) the rom is always the same Lite version. I tried to use also the official wm5 from HTC without manual entry into bootloaded but after flashing is 100% the rom is always udK 6.1 Lite. I have SPL Olipro 1.20 installed (in the past I've had no problems at all!)
Anyone can help me to flash (with lowest risks) my P3600 again?
Thanks to everybody!
no ideas guys?
so no one can help me with an idea???
What version is your Trinity? P3600 or P3600i? Just to confirm eventhough you mentioned P3600 in the subject.
jackkkkk said:
What version is your Trinity? P3600 or P3600i? Just to confirm eventhough you mentioned P3600 in the subject.
Click to expand...
Click to collapse
it's a P3600
Do a hard reset and flash an OFFICIAL ROM from SD-card
Switch to Des' Crash Proof SPL and try flashing the ROM straight from SD card.
This should work.
thank you very much. I've already tried to change to Des Crash Proof but at about 13%-14% it gives me an error when I reboot by softreset the system is always the same. Is it normal? Is there a specific procedure to change SPL software?
If it works at all after SPL flashing, then you must have followed all procedures. Try flashing Olipro's SPL and scan for bad blocks in flash.
nightblade said:
Hi guys,
this is one of my first post here but I read you everytime. So, the problem now is: my P3600 don't want to flash with any rom.
I've just take it back from assistance for to change the black cover (2nd time...) and when I want to flash, as before I was given to the assistence, with udK 6.1 rom it don't want to flash with any other roms!!
I've now download the Lite version of udK 6.1 and install it but when I've discovered that I prefer the full version that's start the never ending story: I tryed to flash with Full version 2 or 3 time already, the installation goes to 100% but when it restart (should it restart not power off?!?) the rom is always the same Lite version. I tried to use also the official wm5 from HTC without manual entry into bootloaded but after flashing is 100% the rom is always udK 6.1 Lite. I have SPL Olipro 1.20 installed (in the past I've had no problems at all!)
Anyone can help me to flash (with lowest risks) my P3600 again?
Thanks to everybody!
Click to expand...
Click to collapse
Make sure that your SD card it out
have a charmer. I tried to put wm6. but spl and ipl was 1.12. the phone start up and hang when installing some cabs. i restart ir and it allways crashes at t-mobile logo. i updated the rom to aku 3.3. all ok. but continues chashing on t-mobile logo. i try a hard reset. gives me a fat error. I try to put the rom from prophet to try to format it. but that rom upgrade reach 95% and stop. give me a error. this nbf file cannot be used to upgrade this device. I tryed all types of roms. most of them crashes at some point and give me that error. the rom aku 3.3 german and wwe, install perfect. I think that is the only roms I can send to my charmer. but i can´t format whith that rom, fat error. I have 3.08 spl ipl 1.12 because i sent an old charmer rom. ipl downgrade, but spl don´t. do you think my device can be protected?? I dont know that to do more, to bring the charmer back to life. will sd card method work? please help me.
Charmer dead after wm6 update whitout cid unlocking
Hi @all
i have the same problem.
iam stuped and make an wm6 update from ipl1.12 and i have forgot to cid unlock my charmer.
after the update to wm6 all looks like good. the bootscreen from wm6 i have see.
after the reset the charmer hangs at slashscreen.
now i make a update to aku 3.3 ger.
that works but hangs in the t-mobile spaschscreen.
i have tray all downgrading methodes i have read here but nothing works.
jet i have a ipl 1.12. and spl 3.08.
I think only a sd-card rom update works. but i dont have found an sd-card rom to use.
sorry to my bad english.
please can anybody help me?
cu AxelD
Is my phone already dead? Please help me!
Hi, I have a similar may be the same problem!
My phone is a German t-mobile mda compact 2
First I work with “lokiwiz v.02” to unlock the SIM, and it works really well.
Then I installed “Charmer_Touch_ver._2.1” and I could calibrate the screen, and after that Win Mobile 6 installed all the extra stuff automatically. After that the device made a reboot, but it stop at the t-mobile boot screen.
Because the bootload modus is still running, I installed the newest original t-mobile software “RUU_compactII_AKU3.3_38222_382117_026921R_TMO_DE_GER_Ship” but this also didn’t solve the problem.
Hard reset didn't work and always says "Format is
The Start screen shows me this information:
IPL 3.08
SPL 3.08.0000
GSM 02.69.21
OS 3.8.2.22
Is my phone really dead or could someone tell me a trick to reactivate it?
I think noone have a solution for us. I tried to send commands to phone whith mtty. and I can´t send. I don´t know why. so f we cannot send commands the sd card method will not work too. the only olution is to jtag the charmer. but can´t find any pinout information. if anyone knows this informtion, please help.
hi all,
i am having a problem with the trinity i unlocked sim with a tool i found here and then upgrade rom to 6.1 using hardspl 1.30 by oli till now everything is fine and working i decide to upgrade the radio rom and the flashing went 100% but when the device rebooted it was showing no gsm and it would start windows and get stuck in windows loader i tried to refalsh spl to 1.2 to des and always flashes 100% but 1.30.olipro stays tried to reflash with every radio rom i found for trinity and always flashes 100% but still no gsm i tried os cooked and official but with no avail. i found the original spl 1.06 but its .bin any one know how to load it on the device.? i found too some other people with same problem but i cant find any solutions i checked the device with mtty there is no bad blocks but when i do checkimage it gives me a error on radiorom checksum timeout..... does anyone has a solution for my problem please ? any help would be really appreciate it !!!!
no GSM FIX
hi all to all of you who have my same problem ... after hours and hours hours of searching and trying to find a solution i manage to get trinity back working ehat i did i used this tool attached found here on xda. its made by POF which i thank very much!!! i used it and downgraded the spl to 1.2 olipro after i could flash ant radio rom..... and was back in the game!! hope this could help you all who have the same problem
Hi thanks for this info I have the same prob. Would you plz tel me which ROM did you use to revive your trinity.
thanks
hi,
i have the problem of no gsm ...i download your tools but i dont khnow how to use them ...pleas help me ...
sorry for my english
I've tried to download the ROM, but HTC tell me this "Sorry, this software download is not suitable for your device".
Maybe my device s/n number is not correct.
Maybe someone who has the correct s/n could download this ROM~
Just tell you guys the news~
http://www.htc.com/europe/SupportDownload.aspx?p_id=174&cat=2&dl_id=537
Caxio's and frednd's DownLoad Link--(I wanna say THANK YOU VERY MUCH!)
See page3 #21 & #23
Filename is :
HTC Touch 3G_MR2009_RUU_Jade_HTC_Europe_2.32.401.2_Radio_Sign_12.41.30.16_0.41.30.12_Ship
edit:
on booting the last red line (after radio and protocol) now says :
D 2.32.44800
Date (which shows after first boot) after screen calibration is now set to 25/03/09
(in settings / about) Build : 5.2.20771 (20771.1.4.6)
(in settings / device info) : rom version 2.32.401.2(44800)
ON customization after first boot if scaned for wifi networks and poped up a message about available networks
Ht845kh14923 :d
o2p63 said:
Ht845kh14923 :d
Click to expand...
Click to collapse
This is for italian version.
Downloading this know !!!
Will i be able to flash it to my device now i have used HardSPL ??
Downloading this know !!!
Will i be able to flash it to my device now i have used HardSPL ??
It seems HardSPL 1.40oli and this 2.32 rom don't work very well.Very sluggish and phone can't turn ON even after 2 Hard resets.
What is your experience???
Do not install if hard spl
I installed the ROM upgrade from HTC, it ****ed up my device real bad: phone module not working, device boot up in aprox 1 min, after 3 mins Touch Flo not started, it restarts by itself.
I did hard reset and nothing happens.
I,m reinstalling jademan superrom!
I hope that works!
Could anyone check, if the gps-support has been improved?
km
lexx2009 said:
I installed the ROM upgrade from HTC, it ****ed up my device real bad: phone module not working, device boot up in aprox 1 min, after 3 mins Touch Flo not started, it restarts by itself.
I did hard reset and nothing happens.
I,m reinstalling jademan superrom!
I hope that works!
Click to expand...
Click to collapse
Exactly same symptoms. I went to Stock SPL 1.40 and reflashing the new rom now. Hope it works better
update : Jade is fine now. New SPL is 2.32.0000 . More testing to be done.
Question : Can HardSPL 1.40.oli be flashed over new 2.32.0000 ?
lagoskon said:
Exactly same symptoms. I went to Stock SPL 1.40 and reflashing the new rom now. Hope it works better
Question : Can HardSPL 1.40.oli be flashed over new 2.32.0000 ?
Click to expand...
Click to collapse
How did you go back to Stock SPL 1.40 ?? Where can i find this ??
Myster said:
How did you go back to Stock SPL 1.40 ?? Where can i find this ??
Click to expand...
Click to collapse
This is on the Hard-SPL page along with the Oli version
http://forum.xda-developers.com/attachment.php?attachmentid=166262&d=1236988725
GPS seems to work fine now, also the scroll behavior of opera is better
km
It is annoying that hardspl doesnt work with this upgrade of jade.. can't built a rom now with the new oem. It's all newer than the iolite versions, but still doesnt include Footprint
Any changes in Manila? New tabs? Calendar? Stocks? Changes in the contacts?
Hi
What is the Radio version in this new ROM?
I have just applied the version from here and if this contains the old Radio then I can hold off for now until hopefully a compliant Hard-SPL is made, I can live without Opera being perfect.
Hi all,
I'm a new owner of a Jade since april 11. I'm french so excuse me for my english ^^'
I installed this new rom, and i get exactly the same problems as Lexx2009 and Lagoskon. I tryed to install the stock 1.40 rom but it doesnt work. I can synchronize the phone but i cannot use customRUU or hard spl anymore, it says the Jade isn't plugged with the usb cable ..
Please can anyone tell me what i have to do to get a rom whith works please
nereus114 said:
Hi all,
I'm a new owner of a Jade since april 11. I'm french so excuse me for my english ^^'
I installed this new rom, and i get exactly the same problems as Lexx2009 and Lagoskon. I tryed to install the stock 1.40 rom but it doesnt work. I can synchronize the phone but i cannot use customRUU or hard spl anymore, it says the Jade isn't plugged with the usb cable ..
Please can anyone tell me what i have to do to get a rom whith works please
Click to expand...
Click to collapse
Install a different rom from this forum-> Shut down your jade, unplug it. Hold down "volume down button" and ""power on button" to get in to boot mode. now start to flash another rom.
when finished you can install stock spl and then install this new rom
Stupid (or not so stupid) question,
If we flash original SPL to instal this ROM, and SPL is upgraded by this ROM to 2.32,.... and HardSPL does not work with this new 2.23 SPL,.....
THEN, IT SEEMS THAT FOLLOWING THESE STEPS WILL ONLY MAKE US SLAVES OF THIS NEW & OFFICIAL HTC ROM!!!! i.e. No possibility of other ROMs flashing until new HardSPL is developed,...
Please, somebody to confirm this statement?
Thanks,
Jarel
jarel said:
Stupid (or not so stupid) question,
If we flash original SPL to instal this ROM, and SPL is upgraded by this ROM to 2.32,.... and HardSPL does not work with this new 2.23 SPL,.....
THEN, IT SEEMS THAT FOLLOWING THESE STEPS WILL ONLY MAKE US SLAVES OF THIS NEW & OFFICIAL HTC ROM!!!! i.e. No possibility of other ROMs flashing until new HardSPL is developed,...
Please, somebody to confirm this statement?
Thanks,
Jarel
Click to expand...
Click to collapse
that's right.. but i think it's in one of the drivers. using the old drivers and the new oem/sys makes it possible to run it with the current hardspl.
radio in this rom 0.41.30.12
no changes in manilla tabs, don't know what changed but it's newer