I have install one of roms WM 6.0 from here on my MDA II and it was working. Then I've found a polonisation (cause I'm from poland) to it, and I installed it. MDA stopped working . I can turn it on but it stopping on the startscreen and I can't do nothing . I was trying everything- cold reset and even WM reinstallation. How can I turn it back to life?? plz help
P.S Sry for my english
Did u follow all the instructions correctly...Try to go into Bootloadermode (the basic settings to start the flashing) after that You have to hardreset your device.
Press ResetButton and hold down CameraButton + RecordButton.
Hold them pressed until the "Boot Options" menu appears on the screen.
Select the options as follows:
(for selecting use RecordButton, change values with CameraButton)
Enable KITL -> NO
Clean Registry Hive -> YES
Format Storage -> YES
When done, press DPad and wait until OS starts.
Yeah, it's working now, thanks !!
you are most welcome
Related
now i upgrade my mda3 to Helmi Windows Mobile 6 Profesional R0
CE OS 5.2.1620 (Build 18125.0.4.2)
and instalation was finish bout 4 min,that was wired,so when i restart half of programs didnt work.i search for problem and see my latest version of activesync was 4.2,i download last version and every time when i start upgrade again i push next then i got this.
http://img208.imageshack.us/my.php?image=55895612mi0.jpg
i check onlline problem for activesync all works ok,i configure my firewall..thx for every help and sorry bout my eng..
best regrades from cro..
if you dident do a
Enable KITL -> NO
Clean Registry Hive -> YES
Format Storage -> YES
in the bootloader after the flash it could be because you have ½ of your old regs and such
thx now works,but wired thing is because i again install wm6 and instalation was finished bout 3 min..hm i hope so all is ok..
new problem i cant surf on net when mda is connected via activesync,with my last mda no problem but with mda3 nothing,i lost whole day with trying but ,please helpp..
Enable KITL -> NO Clean Registry Hive -> YES Format Storage -> YES
Where are this value:
Enable KITL -> NO
Clean Registry Hive -> YES
Format Storage -> YES
Where I can set it?
Thanks
@secur
do hard reset
hold mic+camera button and reset button
Active sync
Hi,
I had a similar problem with active sync solved installing latest actyve sync version and turn off completely my firewall.
good luck
fixed,dns was problem..
secur said:
Where are this value:
Enable KITL -> NO
Clean Registry Hive -> YES
Format Storage -> YES
Where I can set it?
Thanks
Click to expand...
Click to collapse
press CAMERA+RECORD and Reset at the same time
waiting for popup message
pres Record for select yes/no
press Camera for next selection
and then press message button to confirm selection
Hello, moments ago I tried to install an app which I assume was designed for windows mobile 2003, I think it was a bit of a stupid idea..
Anyways, it looked like the install shell (within the ppc itself, because I executed a .CAB file) hung.. so I did a soft reset..
Well, the conclusion is, my Himalaya hangs at bootup now.. is there anything I could do to make it boot again?
thanks
himalaya finally boots
lol no problem
I fixed it.. woahh!! that was worrying..
For future reference however, I did the following method:
Reinstalled the OS, with the origional TofClock install files, once that made no difference, I did some more browsing of this site and did this again:
----------------------------------------------------------------
3. Hard reset your pda.
Press ResetButton and hold down CameraButton + RecordButton.
Hold them pressed until the "Boot Options" menu appears on the screen.
Select the options as follows:
(for selecting use RecordButton, change values with CameraButton)
Enable KITL -> NO
Clean Registry Hive -> YES
Format Storage -> YES
When done, press DPad and wait until OS starts
(taken from one of the tutorials that came with the TofClock install manual' I've seen it posted by a user named helmi_c)
-----------------------------------------------------------------
But anyways I'm glad that's over, now I only know one contact but I'll live..
i would have replied but my internet was down...the procedure u followed (by helmi) should have been ur priority...any way glad that ur problem is solved..
Mods please lock this topic
I tried to upgrade my SPV M2000 fromWM2003 to WM6 and that happened. I'm using Vista, just telling you because some of the guides I looked at for fixing that were specifically for Vista but they didn't work. Anyone any ideas? I don't mind having to stick to WM2003. Please someone HELP!!!
If someone helps me could you go through everything from how to get it out of the state it is in now to upgrading/downgrading to WM6 or WM2003 with links and stuff please. And if you can help could you add me on msn please. [email protected]
try this link
http://forum.xda-developers.com/showthread.php?t=291723
Yea, tried that, no luck. I'm not sure how to update the driver.
Johnathan1707 said:
Yea, tried that, no luck. I'm not sure how to update the driver.
Click to expand...
Click to collapse
Do not put your XDA into the cradle yet....
1. Download USBAS file and extract to Desktop
2. Right click on My Computer.
3. Select Device Manager.
4. There should be one with Windows Mobile or something like that.
5. Update driver and slect USBAS file you extracted.
6. when completed insert device.
There you go
It isn't listed in Device Manager unless it is in the cradle.
I got it all sorted .
Glad to hear it....
http://www.modaco.com/content/windo...u-on-vista-it-can-be-done-the-ultimate-guide/ That's where I got the fix from .
You should start this as a new post
Don't suppose you want to help me find a WM6.1 ROM and help me install it, or point me to some instructions. Any that
I have found have had lots of download lonks and loads of other stuff I'm not sure about, the one that's on atm was just a siple double click and next job.
Johnathan1707 said:
Don't suppose you want to help me find a WM6.1 ROM and help me install it, or point me to some instructions. Any that
I have found have had lots of download lonks and loads of other stuff I'm not sure about, the one that's on atm was just a siple double click and next job.
Click to expand...
Click to collapse
Hi,
this has the link with the walk through
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel_WM5_Home
This has the ROMS
http://forum.xda-developers.com/showthread.php?t=403421
Install the ROM then the ExtROM
Thank You.
Here is the guide
Temporary Remove your SD Card (it may work for you with the SD card still in your BA, but better to be sure)
Put your device into Bootloader mode by pressing and hold the "Power" & "Record" buttons, and then press the Reset Button
Connect the phone to the sync cable/cradle.
Now you can upgrade the ROM using BaUpgradeUt.exe / MaUpgradeUt_noID.exe
When the upgrade is completed, you must perform a Hard Reset
Press and hold the "Power" button, and then press the Reset Button. Colored stripes (the bootscreen) will appear on the screen.
If you have a PH20B device such as MDAIII, QTEK 9090, XDAIIs, PDA2K etc, EITHER:
Quickly press "Record" & "Camera" before the versions appear at bottom right
OR press "Power" & "Camera" & "Record" buttons and Reset at the same time
If you have a PH20B1 device such as SX66:
Quickly press "Record" & "Windows Media" before the versions appear at bottom right EITHER
OR press "Power" & "Windows Media" & "Record" buttons and Reset at the same time
You'll see three options on screen. You must change the second and the third to yes. If you are not developing/testing software you can disable the first debug option for better performance.
If you have a PH20B device such as MDAIII, QTEK 9090, XDAIIs, PDA2K etc, use "Camera" and the "Record" buttons.
If you have a PH20B1 device such as SX66, use "Windows Media" and the "Record" buttons.
Note: The "Record" button moves up and down the menu and the "Camera" button toggles Yes/No. When you're done, press the button in the middle of the D-Pad to continue booting.
Press the "Mail" button. A white screen will show for 30 seconds, while it is clearing your device in preparation for the new ROM to start executing
When the bootscreen, aka. the colored stripes is displayed, wait more, you are booting. The welcome screen to set up your device will appear shortly ...
(if removed earlier) Put back your SD Card before you do the setup. This way the installation from the SD will continue after you have done the setup
Your upgraded ROM is now running!
During the first boot the CAB-files from "EXTROM" folder will be installed
hi to every one i just want to thanks you gays work this great job,but i need a little help,I have i-mate pocket pc phone edition it was with wm2003 I updated with wm6.1 but not working well so i try another version but same 6.1 now it works well but it shows me 3 media player,3 search,3 options of help,and down the screen it shows a line with color,so what i should do pl help.
best regards from me
sorry if I posted in wrong sesion
try to hard reset using this method :
Press ResetButton and hold down CameraButton + RecordButton.
Hold them pressed until the "Boot Options" menu appears on the screen.
Select the options as follows:
(for selecting use RecordButton, change values with CameraButton)
Enable KITL -> NO
Clean Registry Hive -> YES
Format Storage -> YES
When done, press DPad and wait until OS starts.
ather90 said:
try to hard reset using this method :
Press ResetButton and hold down CameraButton + RecordButton.
Hold them pressed until the "Boot Options" menu appears on the screen.
Select the options as follows:
(for selecting use RecordButton, change values with CameraButton)
Enable KITL -> NO
Clean Registry Hive -> YES
Format Storage -> YES
When done, press DPad and wait until OS starts.
Click to expand...
Click to collapse
IT WORKS THANKS BRO THANKS VERY MUCH
THAAAAAAAAAAAANNNNNNNNNK YOUUUUUU
You are welcome..but next time first read the "readme"
Hey, "ubejd," I'm glad you got it working!
T'was so simple for Ather.
Hello,
I don't know why i cannot perform it.
Are there some roms that don't let the reset to be performed?
I push through the hole with the pencil and switch on at the same time. This thing worked before, but I don't know why it stopped and now i have 5 office folders and a lot of error in my himalaya.
Anybody with the same problem?
Danke
if you have wm5 ot later you have to enter the bootloader and choose clear storage and reg hive
to hardreset your device :
Press Reset Button and hold down Camera Button + Record Button.
Hold them pressed until the "Boot Options" menu appears on the screen.
Select the options as follows:
(for selecting use Record Button, change values with Camera Button)
Enable KITL -> NO
Clean Registry Hive -> YES
Format Storage -> YES
When done, press DPad/Action Button and wait until OS starts.
Thanks Ather. It worked perfectly.
ather90 said:
to hardreset your device :
Press Reset Button and hold down Camera Button + Record Button.
Hold them pressed until the "Boot Options" menu appears on the screen.
Select the options as follows:
(for selecting use Record Button, change values with Camera Button)
Enable KITL -> NO
Clean Registry Hive -> YES
Format Storage -> YES
When done, press DPad/Action Button and wait until OS starts.
Click to expand...
Click to collapse
Thanks ather90, it realy works