Related
Hi,
i have upgraded to WM6 to Tofclock's version and all was fine, now i cannot sync with either of my PC's running XP and Vista. i get a "device not recoginsed" error message and my Himalaya has locked up?? is there another way of going back to WM2003 ?
any help would be greatly appreicated.
You have a activesync 4.5 ???
problems!!
i am using active sync on my laptop running XP and i've tried windows mobile device center on my PC running Vista. if i thought it would work i'd hook up my himalaya to my Wii..... ?
try going to settings>connections>USB to PC and enable the option if it isnt n if it is try disabling it.
make sure u are connecting ur USB cable directly to ur PC not via a hub..also make sure if ur Connector is soldered in the right place..maybe its broken or moving..some times i also get this type of error..try to softreset also and restart ur windows too
problems !!
thanks guys all sorted, it was the "usb to pc" link that was unticked.
thanks again
I was performing the radio update on my MDAIII and now he hangs in the bootloader with USB in the upper middle und 2.08 in the under middle. All resets won`t bring it back to life. If I try to reinstall the update all I get is a blank message screen (update from version to version) in my Vista. How can I get out of there.
I did everything what was stated here
The original BAUpgradeUT won`t find my device. The MAUpgradeUt_noID.exe gives me the blank screen with the update from to screen.
Drake008 said:
I was performing the radio update on my MDAIII and now he hangs in the bootloader with USB in the upper middle und 2.08 in the under middle. All resets won`t bring it back to life. If I try to reinstall the update all I get is a blank message screen (update from version to version) in my Vista. How can I get out of there.
I did everything what was stated here
The original BAUpgradeUT won`t find my device. The MAUpgradeUt_noID.exe gives me the blank screen with the update from to screen.
Click to expand...
Click to collapse
I'm using a Vista PC.
After the Radio update to 1.15 the error described above is not to go away yet.
What to do, I'm nearly in tears.
Finally I got it back but with an old Romupdate from T-Online. Is there someone who got the QTC 9090 update (latest one)
That was fast..
im glad you solved your problem.
i think someone here has it.
just post what you need and make it as a title for others to read in the digest.
Im not a expert but is vista the problem??
Most likely.
Failed MDA II flash with vista notebook
Hello everybody,
I just read this thread in hope to find a solution for my problem, which is quite similar to the one described here initially.
I got a used MDA III with T_Mobile ROM. Since I'm a customer with O2, I wanted to change the ROM to O2 as well. I followed the directions given in an other thread here (don't have the link just now) and during the flashing, the flash application suddenly had no connection to my MDA III anymore. It was securely settled in its craddle an connected to my laptop via USB. Now my MDA III is stuck in Bootloader Mode with USB v2.07 displayed on the screen.
Each retry of installing either the O2 or the T_Mobile ROM now meet with the error 101: no connection. I read here that you managed to update successfully with a vista pc. Thus I wanted to ask, how you did that since I just don't seem to find the reason for the connection failing each time.
Here is what i tried to establish connection so far:
* disabled virus scanner & firewall
* unplugged the mda III and plugged it in again. It was recognized as a new device but that didn't help the connection issue
Could you please post what you did to make the update work under vista? Help would be greatly appreciated
mda3newbie said:
Hello everybody,
I just read this thread in hope to find a solution for my problem, which is quite similar to the one described here initially.
I got a used MDA III with T_Mobile ROM. Since I'm a customer with O2, I wanted to change the ROM to O2 as well. I followed the directions given in an other thread here (don't have the link just now) and during the flashing, the flash application suddenly had no connection to my MDA III anymore. It was securely settled in its craddle an connected to my laptop via USB. Now my MDA III is stuck in Bootloader Mode with USB v2.07 displayed on the screen.
Each retry of installing either the O2 or the T_Mobile ROM now meet with the error 101: no connection. I read here that you managed to update successfully with a vista pc. Thus I wanted to ask, how you did that since I just don't seem to find the reason for the connection failing each time.
Here is what i tried to establish connection so far:
* disabled virus scanner & firewall
* unplugged the mda III and plugged it in again. It was recognized as a new device but that didn't help the connection issue
Could you please post what you did to make the update work under vista? Help would be greatly appreciated
Click to expand...
Click to collapse
Try on computer with Windows XP and kill activesynk (wcecomm.exe on taskmanager/processes)
Maybe it will work. If u cant flash O2 ROM try to use "MaUpgradeUt_noID.exe". On my Qtek 9090 allways flash using this APPS and allways work.
U can try too format device first, put it on candle and use "mtty1.42.exe". On XP, kill active sync, and open mtty1.42.exe and select port USB and put OK. Do "Enter" on command and should appear USB>. After this write Task 28. This will format all your PC. Try install SO after this. This command delete all files on PPC. I have attach files that you maybe need.
thankfor the tipp and sorry for my late reply. Since I have no XP PC available i tried the mtty1.42.exe on my vista notebook. When i run it however, it only lists com port 1-3, no usb port. Do i have to make a special configuration on vista for it to work?
Thanks in advance,
mda3newbie
mda3newbie said:
thankfor the tipp and sorry for my late reply. Since I have no XP PC available i tried the mtty1.42.exe on my vista notebook. When i run it however, it only lists com port 1-3, no usb port. Do i have to make a special configuration on vista for it to work?
Thanks in advance,
mda3newbie
Click to expand...
Click to collapse
In vista i dont know...sorry for my late reply too.... in XP u must kill ActiveSync process called wincecom.exe. in vista, maybe u have to kill the Windows Mobile Device Center....i dont know...
Dont forget, put the Qtek 9090 in Boot Loader Mode (Pressing Power Button + Record Button + Reset), maybe will appear USB and u can format the device.
If this does not work, try on Windows XP....Find a friend with Windows XP and ask him to use his PC only to do that.
Maybe somebody in forum have the Windows Vista and can help u....
Sorry my terrible english....
Sjogos said:
Try on computer with Windows XP and kill activesynk (wcecomm.exe on taskmanager/processes)
Maybe it will work. If u cant flash O2 ROM try to use "MaUpgradeUt_noID.exe". On my Qtek 9090 allways flash using this APPS and allways work.
U can try too format device first, put it on candle and use "mtty1.42.exe". On XP, kill active sync, and open mtty1.42.exe and select port USB and put OK. Do "Enter" on command and should appear USB>. After this write Task 28. This will format all your PC. Try install SO after this. This command delete all files on PPC. I have attach files that you maybe need.
Click to expand...
Click to collapse
hi guys I tried the step by step process and when im enterin( Task 28 ) then pressed Enter -
Invalid command : Task28
For a help screen, use command ? or h
does any one know where the problem is??
Try this
Downlaod the XDA IIs .exe file and run it - no need to put into USB mode
http://www.o2online.ie/wps/wcm/conn...es+&+accessories/Xda+Range/Software+upgrades/
this should reset to factory default (o2)
it runs on vista too
I am not 100% sure it will work but worth a try
diesel_dog said:
Im not a expert but is vista the problem??
Click to expand...
Click to collapse
Yes, i know my reply is late but the problem ist 100% Vista! i Tryed 2 ours with vista...then i decided to format my pc and to install XP. At the first try it worked!
My Blue Angel Activsyn Is Not Recognized By The Pc For A Reason I Do Not Know , Tried Many Times Hard Reset Soft Reset , Mtty Tool
Bootloader Mode Nothing Is Working If Any One Has An Idea How Can I Upgrade Or Even Re Falsh The Same Rom I Will Appreciate It Thanks
mohannad18 said:
My Blue Angel Activsyn Is Not Recognized By The Pc For A Reason I Do Not Know , Tried Many Times Hard Reset Soft Reset , Mtty Tool
Bootloader Mode Nothing Is Working If Any One Has An Idea How Can I Upgrade Or Even Re Falsh The Same Rom I Will Appreciate It Thanks
Click to expand...
Click to collapse
You MUST flash via sync, there is no method available to flash from SD card. Are you using XP or Vista? There is a known issue with Vista not liking the BA. Are you manually putting the BA into bootloader mode then placing in the cradle or trying to do it some other way? The method that works 100% for me is to manually put in bootloader mode (power+reset+record), this gives me a screen that says Serial at the top and a version number at the bottom, there is no backlight and when I then place it into the cradle Serial changes to USB. At this point on the computer run MA_Upgrade and everything should work. Keep in mind that I will never use Vista so if you are the YMMV.
will i could manually go to bootloader mode but the time i place device on cradle " unknown device" appears and running the maupgrade.exe leads to blank upgrade rom version several times i have done it ??? any suggestions
i have windows xp , activsyn 4.5 , bootloader ver 2.06
mohannad18 said:
will i could manually go to bootloader mode but the time i place device on cradle " unknown device" appears and running the maupgrade.exe leads to blank upgrade rom version several times i have done it ??? any suggestions
i have windows xp , activsyn 4.5 , bootloader ver 2.06
Click to expand...
Click to collapse
As silly as this sounds, try a different USB port. Also make sure you are directly connected to the computer not via a USB hub.
tried more than one computer for connection and more than 4 ports still i got the same " usb device not recognized"
mohannad18 said:
tried more than one computer for connection and more than 4 ports still i got the same " usb device not recognized"
Click to expand...
Click to collapse
Try a different cradle/cable.
The time I had this exact problem, it turned out of be a broken wire in the data cable.
i bought another cradle still i hvae the same message " usb device is not recognised"
Hrmm... I'm going to throw out a few ideas to look at. Some probably don't apply since you tried this on another machine, per your post, but it can't hurt in regards to this issue...
Try uninstalling activesync, reboot, reinstall, reboot. The 'drivers' that are used are installed with activesync.
If you have any 3rd party USB drivers, try reinstalling them.
Disable 'advanced network functionality' on the phone
Backup your phone and hard reset
Do you have anything that monitors the USB port on the machine you are trying to do this on?
Make sure you are using activsync 4.5 or newer. Other than that and what you already read here I can think of nothing.
i have tried so many versions of activesyn 3.x-4.5 with reboot each time of installation ,advanced network diabled, still the same thing " usb device not recognized"
sorry for inconvenience what is usb moniter machine??
BA - Does the activesync (3x-4.5) - work via bluetooth 4 U/G's ?
Angel - Does the activesync's (3x-4.5) - work via bluetooth 4 U/G's?
(no cradle / no usb) , but file transfere's work ok, via BT exchange folder (paired)
for running the ====#====#===#XDATools#==#=== & the #====#====#====#special_rom_1.2.exe#==#
angel of the ph20b
1.31.00 wwe
rom 12/13/04
1.06.00FM
1337.38,
ext rom 1.31.139wwe - flavours
my BlueTooth is belkin F8T008 (belkin say it uses comm4) - (BlueAngel say it uses - in comm5 / out comm 6), & activesync4.5 says (no-way, even adding ports, then removing all under comm9 etc)
(if I could run them from midlet, from sd say )
ASK B4 U TRY ??? (101/Flash4dummies/NewbiesTube . . . .YouNube? where ()not the wiki() - Im getting to be a silver surfer, already!
followed a few tutorials, none look like my sp3, on xp-pro, I also have no outlook, etc (no excel, - NO office!), but I only came for a soft-key fix/addon = 4midlet's)
tried removing the pair'ings from regedit(then regclean). Oh and when running activesync from BA, I cannot even get a PC (discoverable 'n all devices 'n all services ect
and breathe!
Oh and any reply's would be gratefully received, B4 '2010', that is -
shame the bolt that was shot, was just too soon, so no score for the aim, though! -
usb activesync problem
usb activesync problem
ignore the previous post - cannot connect to activesync via bluetooth!
radio upgrade worked !!!!!!!!!!!!!!!!!!!!!!!!!!!
special_rom_1.2.exe, unzipped to a xdatools folder
running start.bat, after activesync's finnished sync-ing
in the dos window I get a get device error
and
error 011:execute remote comms prog error
I'm VNese, my level of Eng is poor. but I think u should check your USB port. Do u use full of usb port? may be, the power in USB port is low -> error. Or hardware(USB chip) is bad. check more
Shot in the dark but I had the same problem with a friends 6700. I found out that the antivirus/firewall/internet security suite was blocking the proper ports needed to connect. When I disabled the software for a moment, attempted a sync it would work, then I could turn the software back on and be fine. If I disconnected and reconnected it would only charge. Give that a whirl.
im not a newbie, ive flashed alot of roms on my wizard, using shelltool.
so i decided to change my rom after using it for like a month
using shelltool didnt go as planned, so i decided to flashback to wm5 using wizardlove.
now this is where the problem is, i get into bootloader, connect my device, and start ruu, but now theres a connection error.
any ideas?
thanks
tshizzle said:
im not a newbie, ive flashed alot of roms on my wizard, using shelltool.
so i decided to change my rom after using it for like a month
using shelltool didnt go as planned, so i decided to flashback to wm5 using wizardlove.
now this is where the problem is, i get into bootloader, connect my device, and start ruu, but now theres a connection error.
any ideas?
thanks
Click to expand...
Click to collapse
Check and confirm establishing connection with pc via usb cable in bootloaders,did small 'usb' show in the bootloaders ?
Don't use 'Shell tool'.Get the phone Activesync and 'HardSPL' or 'SoftSPL' and flash the Rom.Btw,which windows is it WinXP or WinVista you are trying with.
it does show usb at the bootloader screen
im using windows xp
and when i cnect it, my computer finds a new usb device and cant install it.
tshizzle said:
it does show usb at the bootloader screen
im using windows xp
and when i cnect it, my computer finds a new usb device and cant install it.
Click to expand...
Click to collapse
Delete all previous profiles/partnership or completely uninstall activesync and install it again,close or shut down all firewalls/Antivirus,uncheck 'Allow usb connection' in the activesync and uncheck 'Enable advanced network functionality' in the settings...> connections...> usb to pc
Cheers!
Hi, I've an Ba with WM6.5 in it. But when I want to reflash it, the BA wasn't detected by my computer. I've put it into the bootloader mode, but it just shows Serial, even I've waiting for almost 2 hours. But when I boot the OS, it can connected to the PC via ActiveSync. What's going on here?? Is my BA or my cradle broken??
are you running XP if so open CTRL ALT DEL then look for wscesscom or somthing and end task and then WcessMgr OR somthing and end task and try
You should see Troubleshooting in the WIKI ~ http://forum.xda-developers.com/wiki/ActiveSync
I've done all of that, but still not working. I think it's not in the activesync, because I can connect my BA to the PC, the problem looks like in the bootloader mode.... It just standing there shows "serial" and "V2.07", even I've connect it to the USB port... Any ideas??
Is there are any possibility I can repair my bootloader (if it's really broken)??, or Can I reflash my BA with other way around?? Without using the bootloader maybe??
UPDATE:
Later, I think I began to recognize the problem...
In every tutorial for Win7 that I read (this tutorial and d-two's tutorial), I was ask to update the driver of "Microsoft USB Sync". But in my case, that "Microsoft USB Sync" wasn't shown. I think it's because I haven't sync my BA with the PC yet (I've just reinstall my Windows, so all of the setting is gone). If you sync your BA, you will get the "Microsoft USB Sync" on your device manager.
But now, the problem is, I can't sync my BA with the PC, because of error in my PIM (Contact, Calendar, Task, Phone, Messages, etc). I only able to explore my devices through ActiveSync/Windows Mobile Device Center, not synchronize it. Even my ActiveSync/WMDC shows an error on the connection. So, I can't update/install the driver for "Microsoft USB Sync", because my BA have an error connection with the PC. Any ideas to solve it??
And would cloning method worked for my devices?? I mean, I get a cloning from another BA, install it in my BA, and then repeat the reflash process with my preferred ROM??
Please, need help over here....
try a hard reset
Broken Power Switch ...
Dear experts,
My device is PDA2K, last week i did upgrad from original windows to WM6.5 Pro_QVGA, Radio 1.12.00 ...... but the power switch is broken
..... as your experience how did that happened!!!! it was on cradle connected to WinXP, but since that day i'm trying to do flashing to install another Windows ...... i failed ...
Please Please Please .... Help me to do flashing or formating from pc or sd card ... because i'll never get into bootloader in my life.
Thank you ...