(Untethered, official) Kaiser not booting in? HR doesn't help. - Tilt, TyTN II, MDA Vario III General

Has anyone ever encountered the Kaiser's becoming completely dead, out of a sudden? HR doesn't help. It has the official Kaiser ROM - and not even any hacks.
After starting, it just prints "smart mobility", vibrates once and, atter a while, repeats this in an infinite loop.

Menneisyys,
my unit did exactly the same thing. Had to send it back, unit was exchanged for a new one.
This behavior goes hand in hand wit the "Standby of Death" and "Red Light of Death" behavior where the unit will no longer wake up from standby or will no longer start up even though a charger is connected. There is a thread on XDA-dev. about this syndrom.
The only information that I can give you is that my first Kaiser which finally died exactly like yours mid-December showed erratic behavior like restarting three times after soft reset and the SoD right from coming out of the box. The replacement unit never showed anything similar.
As far as I can remember there is a good chance that HTC as released a faulty production lot to the market showing these problems.
Get your unit replaced under warranty. Re-flash or any other repair attempts won't work.
Rgds
Joe

I had that issue. I went into bootloader and flashed a new ROM and it fixed the problem.

I am having the same problem now too - I can get it to hard reset after some twists, but it refuses to work when I restore a backup, I'll see if I can get a case that I can repeat so I can send it back...

Related

problem with touch screen, can't click on anything

i just recently bought my xda2s and it worked fine for a week though. now, from time to time my screen would be "untouchable". literally i cannot click anything or open anything even if i soft-reset it for 10x. buttons seem to work fine but the screen does not. it happened twice while my bluetooth was "on" and i thought maybe it was the bluetooth but recently the same thing happened with my bluetooth now turned "off". i have to wait for hours before it would return to normal again. Anybody help please? By the way, my bluetooth version is 1.0.0 build 3500.
I had a similar problem on my Samsung SPH-i700 PocketPC Phone through Verizon Wireless. Even after a hard reset, I couldn't get past the screen calibration, until I found out that a piece of hair and debris found on the outer edge of the screen right under the lip of the cover was interfering with the touch portion of the display. Apparently, the touch sensors extend past the visible area of the screen, so with both a little aircan and vacuum cleaning, the debris was picked up and the touch screen functioned normally again.
Is this a consistent and/or intermittent problem? Did a hard reset resolve anything?
look for the alignment
Do you have Calligragher 7.4 installed? I read about this in Tekguru website that if you re-install 7.3, the problem goes away. That is what I have done and it seems to be working for me so far (2 days test).
i've checked out my screen and i dont see any dirt or something... i even have a screen protector... dont know if that might cause the problem. Same thing happened last night but this time it was just for a short period of time then it went back to normal... I didn't try a hard reset cause i dont want to loose some of my files but if ever it happened again, i might try doing a hard reset and see what happens... right now, im having my xda2s checked if maybe it's a factory defect or something...
regarding the caligrapher program thing, i dont have that...
Hey, i have the exact same problem I bought mine here in Toronto, from an Asian dealer, its the O2 XDA IIs asia-pacific model.
Same problem, screen(touch screen) goes dead like no responses to any touches, for like half hour - 2hour once in a day or something and nothing cures it, hard soft rest nothing. just with time it suddenly starts working and the Handheld is useless until then...well i dont see any cure and this is the only place i have heard about someone else having this issue, i will take it back to the dealer, in hopes of exchanging.
any feedback will be will be appreciated
overclock it for a few days..that fixed mine..dont know how but it did.
There is a tread in blue angel about screen aliment that you might like to read. seems 4k of devices went out with screen problems.
What is overclock it. Fairly new to this. Mine just keeps trying to allign and thats all it does it doesnt go into boot mode just allign screen all the time

Kaiser 4 Colours of Death Again - HELP!

I've just got my phone repaired 2 days ago due to same problem and its dead again. It's showing me 4 colours bars, unable to boot or switch off. Please see attached photo.
Technician Notes on the Service Repair Job Card says " Reconnected Flexes, Loaded New Software and Passed all tests."
Whatever Flexes means? Hardware circuit board problem? Anybody knows whats that?
Its going to be another 2-3 weeks wait for Three Sydney to repair it....sigh....
I'm unable to find similar reported problem online. Anyone, please advice. It died when it shows nothing on the screen with blinking green light. I've not done any flashing or mod of any kind, its a 4 month old phone.
the flexes are what connects the screen/other hardware on the sliding face to the main board on the part that does not slide. Seems like your kaiser is putting itsself into bootloader for some reason. if you have knowledge of mtty maybe running some mtty commands would tell us more of why it seems to like to erase its on memory lol... there is a whole section in the wiki on mtty and I thread I believe also try contacting POF or OLI they have vast knowledge about the works of the kaiser
Thanks for the tips austinsnyc, after leaving it on with the bootloader screen for the whole night until it drain the batt completely, I was able to boot up again while charging.
I'm still interested to know why would it suddenly just go to bootloader screen, i'll read up on mtty.
Cheers,
JK
lol, you might have been fine if you just did a soft reset. but still that doesnt solve the issue of why it went into bootloader in the first place
Thanks for reminding about the soft reset, I tried that when it happen for the very first time I had this problem. That didn't help either and I had to send in for repair.
Whats the purpose of the bootloader anyway? In what situation would it appear normally?
you can manually place your device into bootloader by holding the camera button and then reset. a device going into bootloader out of the blue is usually never a good thing........unless maybe there was a situation where the camera button was somehow held down while your device restarted.

Please Help - Diamond Overheated and is dying !

Hi all, just wondering if anyone else has had this problem...
Last week, on a very hot day in Australia (36*C), I received an SMS message whilst the phone was charging....
Anyway, this turned the Diamond on, and it connected to Wifi, and stayed powered up (for some reason) for a couple of hours....
Anyway, the phone was very very hot when I unplugged it, and since then it has been playing up very badly...
The problem has been getting worse and worse, and Now I am at the stage where the phone is almost bricked !
When I switch on the phone, I am presented with a white screen. (It doesnt boot up)
If I power up holding down the Volume Down, Rest, Power Button, I can get into the bootloader screen.
I can even reflash the phone with a new Rom....
If I reflash, the phone may run for a minute or so, then crash, and refuse to power on..... (Same problem as above)
Im reluctant to send the phone off for warranty, as they cannot give me an estimate of if it can be fixed, when it will be fixed, or what day of the week it is.....
Has anyone else had this problem, and if so, how did they fix it ??????
(Im hoping I just got a dud version... I love this phone, but I am hoping this is not a common problem !?!?!?!)
Cheers for any help anyone provides !!!!!
try removing battery for 10-15 and make sure your running a 1.93 rom because 1.37 and older are known for heat issues.
you may have already done this, but its not in your first post and there are order of operations to follow.
hey buddy even i hav the same problem..it just restarts after heating up..and after 2 restarts it doesnt even go beyond 1st diamond loading screen...dont know what to do....
Guys, send your phones back to repaired or replaced. Just explain to your provider what is going on and I'm sure they'll try to help.
yea buddy...i guess so...thats the best way i can get my diamond fixed..

Dimaond Gets Hot and Screen Alignment Goes Out

I have done a reasonable amount of searching on this and have not found anything specific to my problem so figured I should post a question.
I have an issue with my Dimaond when it gets hot generally either using Wifi or Phone Data connection that the screen goes out. Basically everything goes to the left side of the phone so if you hit the Task Icon in the top right corner you get the Start Menu. Phone is basically useless at this point and you have to wait for it to cool down. Has happened since day one and is generally worse when using it when charging. I was watching Utube on it the other night 5min video while on AC charge and it went out. I am running Dutty 2.5 Rom and 25.07 radio have tryed 25.08 and 25.05 no difference was happening when the phone had orginal HTC ROM as well. Also will happen on a long call if the screen is on.
Basically feel issue is hardware related and maybe faulty screen still under warrenty so wanted to know peoples opinion on weather I should send back. Problem is will take a couple of weeks and I don't really wnat to wait that long if I can help it. Also assume it would be best to flash standard ROM back, should I do anything with HARDSPL eg should this be changed back as well if I send it back.
And before anyone says it I have tryed searching this topic and have found lots about HOT dimaonds but nothing related to screen going out at the same time :-(
Thanks
I had this issue in my JasJam (Hermes) whre the screen would simply go white after a while of use and I would have to leave it for a while for it to work again.
Unfortunately it sa hardware issue and you should claim a warranty repair on it
I can't see how this could be a software problem so I figured it must be the screen eg hardware related. Would be nice to know if anyone has had the same issue with a dimaond... Seems we may be spending some time apart, just hope it doesn't take long to fix..
I've had the same issue
http://forum.xda-developers.com/showthread.php?t=428976
My first device had been replaced recently (i.e. today) by my network provider (o2) and the new device seems to work without any problems now even if it's "hot".
(i.e. default screen adjustment + creating heat by activating the phone, wlan, bt + recharging it)
I sent an email to HTC regarding the fault and they said it would have to go back for a warrenty repair. I brought it through a resellar so has to go back to HK from NZ so will be away three weeks uurggghhh... Just seems odd I don't have any physical damage on the screen but hte problem has been around since day one as I remember having the problem the first day I got it. Juyst seems to be getting worse and is easily reproduced by usiung utube over wifi gets hot and it is all over. Just wondering if I should put an offical ROM from HTC back on the device before I send it back as I currenty am running Dutty ROM, what do you think....
i put the original rom back on and they still found out the the rom had been flashed, and would not repair on warranty
yep, i also asked about this problem
http://forum.xda-developers.com/showthread.php?t=438733
there are some youtube video's of how the phone behaves
my phone seems to do it less frequently since stopping using panosha's rom
im using alpha zero 7 at the moment..
i've also noticed that it isnt necessarily a heat issue, my phone does it completely at random
yesterday i found though, that when the phone did the alignment issue, i gave it a good shake.. and hey.. its all aligned again?!
maybe it was just a fluke, it hasnt freaked out since..
holding thumbs
Hey,
I also have the same screen problem, but my Alignment goes to right.
If I press on the left side, a press on the right side is recognized.
Good to know that Im not the only one with this problem.
greets doena
I got my phone back a week ago replaced the screen has been away for over two months, complete disaster, anyway all sorted now and I have not had the problem since....
I had this exact same issue (out of the box).
It was a hardware fault and I exchanged it for another one.
Haven't had any problems since.
Minus-1 said:
I had this exact same issue (out of the box).
It was a hardware fault and I exchanged it for another one.
Haven't had any problems since.
Click to expand...
Click to collapse
Hardware's fault ? Most likely not. I will give u an example of why I think it was software related. My device ran hot as well but I simply switched roms and now it's the complete opposite. Your most recent device most likely come with a different Rom in the phone.

Xperia restarts automatically!

I am facing the problem recently last 2 3 days
my Xperia restarts automatically
sometimes there is 30% to 40% charging left still its shut automatically and never been start.. i have to change new battery
any solution for this or anyway to find the problem?
regards
anybudy would like to answer this please?
I'm having a similar problem...my x1 sometimes shuts down while in the middle of doing something, like opening apps, sliding out the keyboard or even navigating touchflo. I suspect it could be a battery problem, as someone in the forum discovered, having also shut down problems, that his battery is loose and the connectors are not properly met so he stuck a bit of hard paper to fix it, but I checked mine and the battery is not loose. I don't want to spend on a new battery if these shut downs weren't really cause by faulty batteries, so yeah anyone has a clearer understanding on this?
Hi all
I am also having a similar problem the past 2 days and as of now i cant use the qwerty keyboard because just as i begin to slide the qwerty out the screen goes black and the phone need to be rebooted.
I have just changed to Valkyrie 2.4 yesterday thinking that maybe its was software problem with Touch X but the problem still persists. Only difference is that with Touch X the phone would reboot itself.
Anyone else having any similar issues and what would the fix be, or shall i be off to my nearest service provider for repairs?
Thanks
Uhm.. about that problem when you slide it out and the device turns off.. i had that too and i send it in to repair.. it will probably be fixed under warranty, and stock rom or custom rom doesnt matter the problem was still there... and it happend to me 5 days ago..
knufh said:
I'm having a similar problem...my x1 sometimes shuts down while in the middle of doing something, like opening apps, sliding out the keyboard or even navigating touchflo. I suspect it could be a battery problem, as someone in the forum discovered, having also shut down problems, that his battery is loose and the connectors are not properly met so he stuck a bit of hard paper to fix it, but I checked mine and the battery is not loose. I don't want to spend on a new battery if these shut downs weren't really cause by faulty batteries, so yeah anyone has a clearer understanding on this?
Click to expand...
Click to collapse
'When i slide the thing out it sometimes restarts'
I used to have that with the stock ROM so this all might be more software related...
yeah I am having the same problem, No Water Damage btw. i found that if i sometimes in portrait mode if pressure is applied to the top right region, it will shutdown and/or restart. When I slide my screen up to landscape mode it screen is just black. I'm going to contact Sony Ericsson to see what they have to say about this.
SyntheticDistortion said:
'When i slide the thing out it sometimes restarts'
I used to have that with the stock ROM so this all might be more software related...
Click to expand...
Click to collapse
It resets when the phone freezes. Sometimes it freezes so bad you have to manual reset.
My phone is doing the same thing but when i slide it up. The screen goes blank and then it restarts by itself. I never flashed my phone so I thought it was a firmware issue. I finally updated to the R3A firmware and lo and behold the same results, but instead it didn't restart, it just turned off or the screen goes blank. I've sent the phone to Sony Ericsson and they told me that I would have my phone back in 7 to 10 business days, but they're liars!!! It's been 13 business days and counting and no word as to whether the phone can be fixed or updates on status other than it's in "work in process". So then I called again today and complained to SE and the result is that they are "awaiting parts and Xperia parts are on back-order". After further probing SE told me that they would call me on Monday to officially let me know what the hell is going and why it's taking so long to repair my phone. I paid $800 usd for the phone and I would expect that their repair service would be a lot better and quicker than what it is! During my wait time for my phone, my PS3 broke down, I sent it in, got it fixed and returned already. That was within a week. There is definitely something wrong I tell you! They just need to send me a new phone!
Sorry about my rant guys, but I'm pissed!!!
My damn phone has the same issue, Until now, this hasn't been repaired for it's crack. And I'm almost out of warranty days, I think I bought it 2md day after the xperia was released. I'll try testing abou the presuure point though. I give you update
I did have the same problem..
Hi... I did have the same problem n I couldn't find any solution... So i send it to repair...
U can check my threads..
http://forum.xda-developers.com/showthread.php?t=520143
n
http://forum.xda-developers.com/showthread.php?t=519322
mca
EDIT : It seems that is an XPERIA PROBLEM!!!! LOOK!!! : http://forum.xda-developers.com/showthread.php?t=550242 !!!!! , many people is having the SAME problem...
I'm disappointed..

Categories

Resources