ATT 3g problem? - Tilt, TyTN II, MDA Vario III General

Just got the Tilt a couple days ago and didnt hesitate to go ahead and put duttys 2k8 rom on. The radio is 1.127.12.11. Ive got 3g/hsdpa in my area, and was working just fine. Until last night, all i get is edge. My roomate has 3g and its working just fine on his phone, but all day nothing for me no matter what i try. i installed a couple of programs but nothing that should mess with the internet. Maybe it was something Kaiser Tweak done, that would be the only thing i could think of messing with the phone?
I find it weird to just stop all of a sudden, anybody know registry settings or maybe att settings that may have accidentally gotten changed? I have searched all last night and day and have gotten nowhere. Thanks.

I'd say that if you haven't done much to it yet, do a backup, then a HARD reset. See if it works stock, then restore your backup. This might be the quickest way to see if it's something you did. There are settings in kaiser tweak, and comm manager, and possibly even phone settings that can force the phone to EDGE.
Good Luck

Tried the hard reset already, but it was a no go. I set everything in kaiser tweak to default even, but nothing. Can there be something in the registry forcing it to stay edge?

Under phone settings, do you have your band set to auto, gsm, or wcdma? i normally leave my settings to gsm, unless i plan on browsing the net, then i switch to wcdma for the 3g/H speeds, then switch back to edge when i'm done.

zetajunkie said:
Under phone settings, do you have your band set to auto, gsm, or wcdma? i normally leave my settings to gsm, unless i plan on browsing the net, then i switch to wcdma for the 3g/H speeds, then switch back to edge when i'm done.
Click to expand...
Click to collapse
ive had it on auto since ive had it and it worked just fine. But i just changed it to wcdma (which took like 2 min of a wait screen) and now it works! Something so easy, i feel stupid. Am i going to have to switch it back and forth in 3g/gsm only areas? I thought it was supposed to pick up 3g over edge if you have 3g on?
thanks zeta

heh, no clue really. when i originally got the phone, this was my solution to make calls/texts. it would spend so much time switching on auto that i'd never get to complete a call or receive sms. i eventually switched radios (.19, and now on .32), thinking that it would help. i've read speculation that it is also related to carrier hardware issues. I figure manually switching between gives me the best battery life. there are a few cabs floating about that do the switching for you, if you are so inclined, but i like manually seeing that it gets done...
glad my days of frustration eventually helped someone...

Related

I cant use AT&T internet on certian apps?

It use to work before I had Shaps Rom on mine, now resco apps wont work and on occasion Windows Live Messenger wont work. . . Some other apps are Skype, zsIRC, Coreplayer(Yes I have the 1.1.3 one), some others but you get the idea. What could be the problem? I have the right MEdia Net and AT&T ISP settings.
Anyone? What could the problem be?
It would probably help if you posted your set up, i.e. rom/radio/os versions...
Ah, well, I said shaps rom. And I have the radio ver: 1.27.12.17. It could be the radio, but now I am only getting edge speeds, when I am in a city with all 3G and edge in the suburbs and ghetto areas?
~~Tito~~ said:
Ah, well, I said shaps rom. And I have the radio ver: 1.27.12.17. It could be the radio, but now I am only getting edge speeds, when I am in a city with all 3G and edge in the suburbs and ghetto areas?
Click to expand...
Click to collapse
oh? i thought schaps had more than one rom released.
with my current setup i haven't had any problems or complaints with edge or 3g.
so, how's your rom coming along?
Oh, lol thats what you meant. . . Its the 4.31 one. I dont know. I havent been able to use certian apps. . . and a moment ago it didnt have any connection and now it does and it jumps from edge to GSPA and then sometimes I cant have 3G back and when I do it messes everything up, like the carrier logo says AT&T 3G instead of regular AT&T and it would change the HSPDA symbol to 3G and sometimes its normal with the Hspda symbol? Why does it do that? Well I'm off to be its too late here anyways. ., it could be a network problem IDK but I hope it corrects it self in the morning.
What part of town are you in so maybe you could help me?
the band switching problem is my favorite. you are lucky to only get that now. try turning off your band setting from auto to either gsm or 3g, that worked for me. you could always change your radio and see if that helps.
oh, and your apps not working, ..... hard reset yet?
i'm generally all over town during the day, but i live near the uni.
although i don't know how much help i'd actually be.
Tried that and I don't want to start all over after 6 flashes(During the time I flashed to the shaps rom out of the time I've had it). Well, it works now. It could have been my area. UNLV? I am by the community college.
~~Tito~~ said:
Oh, lol thats what you meant. . . Its the 4.31 one. I dont know. I havent been able to use certian apps. . . and a moment ago it didnt have any connection and now it does and it jumps from edge to GSPA and then sometimes I cant have 3G back and when I do it messes everything up, like the carrier logo says AT&T 3G instead of regular AT&T and it would change the HSPDA symbol to 3G and sometimes its normal with the Hspda symbol? Why does it do that? Well I'm off to be its too late here anyways. ., it could be a network problem IDK but I hope it corrects it self in the morning.
What part of town are you in so maybe you could help me?
Click to expand...
Click to collapse
Normal operation of HSDPA is this: In a 3G area the 3G icon will show. While data is being transferred the H icon will show. Once the data transfer is complete it will go back to the 3G icon. I think part of what you are describing is normal oeration.
-Jay
Well, no. My whole town is almost 3G, so I dont think its that and it would say HSPDA all the time even with out data transfers. I think the network had a hiccup yesterday. It only did the 3G icon thing when I would have been messing with the band selection(hasent happened lately it only happened 2 weeks ago).
~~Tito~~ said:
Well, no. My whole town is almost 3G, so I dont think its that and it would say HSPDA all the time even with out data transfers. I think the network had a hiccup yesterday. It only did the 3G icon thing when I would have been messing with the band selection(hasent happened lately it only happened 2 weeks ago).
Click to expand...
Click to collapse
You should not be on H all the time, even when no data is being transferred. My phone got stuck like that once. A soft reset fixed it.
-Jay
Well not connected, all the time it just says [H], is there something wrong with that? I thought that was 3G? When ever the [3G] symbol comes on the carrier display area not the connectivity area says AT&T 3G and when its normal it just says AT&T.

Tilt Stuck in HSDPA Mode as of yesterday

This is very strange. As of yesterday my Tilt seems to be stuck in HSDPA mode.
Before yesterday when the phone booted it would first momentarily display G mode, then media net would try to connect and it would go to 3G mode. Then as the boot completes the application which access the internet kick in and the phone jumps to H mode for the downloads. When the downloads were done, it would settle back into 3G mode. That is normal behavior for the Tilt as it was for my old Hermes.
As of yesterday it starts in H and stays in H all day and nothing I do seems to be able to get it out of H. I have tried turning off the phone, turning off and on the HSDPA setting, rechecked all my tweaks, no change. I have done everything I can think short of a hard reset.
I was convinced it was a software issue on my phone, until I looked at my wife's phone. Her Tilt is doing the same thing as of yesterday. She is on the stock AT&T ROM (no bloatware) and I am on the Official HTC TYTN II WWE ROM (6.1) So the phones are different in terms of software and tweaks.
Thus I concluded it must be a network issue here in the Orlando Area. The network has been changing here of late. So I call At&t and even their second level tech support could not understand. They said we will have to take the phones back and get new ones.
The batteries are draining very fast in this mode. Does any one have any other ideas? This has to be a network problem, right?
LJinFLA said:
This is very strange. As of yesterday my Tilt seems to be stuck in HSDPA mode.
Before yesterday when the phone booted it would first momentarily display G mode, then media net would try to connect and it would go to 3G mode. Then as the boot completes the application which access the internet kick in and the phone jumps to H mode for the downloads. When the downloads were done, it would settle back into 3G mode. That is normal behavior for the Tilt as it was for my old Hermes.
As of yesterday it starts in H and stays in H all day and nothing I do seems to be able to get it out of H. I have tried turning off the phone, turning off and on the HSDPA setting, rechecked all my tweaks, no change. I have done everything I can think short of a hard reset.
I was convinced it was a software issue on my phone, until I looked at my wife's phone. Her Tilt is doing the same thing as of yesterday. She is on the stock AT&T ROM (no bloatware) and I am on the Official HTC TYTN II WWE ROM (6.1) So the phones are different in terms of software and tweaks.
Thus I concluded it must be a network issue here in the Orlando Area. The network has been changing here of late. So I call At&t and even their second level tech support could not understand. They said we will have to take the phones back and get new ones.
The batteries are draining very fast in this mode. Does any one have any other ideas? This has to be a network problem, right?
Click to expand...
Click to collapse
d/l a communication manager that has a 3g on/off button see if that works
i believe duttys 10 button com manager should do the trick.
Congratulations! ATT turned on HSUPA in your area. What you described originally (3G going to H when doing data transfer and then back to 3G) is what the Tilt does when you only have HSDPA in your area. Once ATT turns on HSUPA (so now you have HSPA for both uploads and downloads) it will stay with H until you leave and enter an area that doesn't have HSUPA.
Bottom line is that there is nothing wrong with your phones.
I am not sure why you are seeing poor battery life. I have been living with H for almost 6 months and haven't noticed any changes in battery and haven't heard other people complaining about that either.
jglev said:
Congratulations! ATT turned on HSUPA in your area. What you described originally (3G going to H when doing data transfer and then back to 3G) is what the Tilt does when you only have HSDPA in your area. Once ATT turns on HSUPA (so now you have HSPA for both uploads and downloads) it will stay with H until you leave and enter an area that doesn't have HSUPA.
Bottom line is that there is nothing wrong with your phones.
I am not sure why you are seeing poor battery life. I have been living with H for almost 6 months and haven't noticed any changes in battery and haven't heard other people complaining about that either.
Click to expand...
Click to collapse
Wow jglev, thanks for the prompt info. Even the AT&T techies couldn't tell me that. I asked them about the network changes that have been going on. We have noticed that the name of the network has been changing over the last week fro "umts-AT&T" to "3G AT&T" to now just "AT&T" so I knew there were changes. But when i asked AT&T specifically, they couldn't tell me. Not surprising i guess.
My battery statement was more of an assumption I guess. it was my understanding from my past with the hermes that when the phone went into H mode the radio would take more battery power. and that is why the OS settles back into straight 3G mode in between downloads. Do you know if that is true on the Kaiser. What kind of battery life do you get in the HSUPA mode?
LJinFLA said:
Wow jglev, thanks for the prompt info. Even the AT&T techies couldn't tell me that. I asked them about the network changes that have been going on. We have noticed that the name of the network has been changing over the last week fro "umts-AT&T" to "3G AT&T" to now just "AT&T" so I knew there were changes. But when i asked AT&T specifically, they couldn't tell me. Not surprising i guess.
My battery statement was more of an assumption I guess. it was my understanding from my past with the hermes that when the phone went into H mode the radio would take more battery power. and that is why the OS settles back into straight 3G mode in between downloads. Do you know if that is true on the Kaiser. What kind of battery life do you get in the HSUPA mode?
Click to expand...
Click to collapse
It is true that any 3G mode uses more battery power than say Edge or GSM, but I don't know if full H mode is any worse than just HSDPA. I can easily go a full day without charging, but since I have a charger at home, in the office, in the car and one I travel with, I ususally don't have to. When the phone is displaying H, it doesn't mean it is actively transmitting data, just that the network is H (and if you have the little H by the signal bar, then you are connected to the data network). So even if it's dormant, you will see the H. There really isn't an easy way to see if you are actively transmitting data with the Tilt/Kaiser as far as I know. If I remember correctly when I had the Hermes (which didn't have the little 3G by the signal bar, just the larger square icon), you could tell from the icon (the little arrows would light up), but you can't with the Kaiser.
And yes, for the most part, you will find that the people here (and HoFo) know way more than those who works for ATT (but there are exceptions).
LJinFLA said:
Wow jglev, thanks for the prompt info. Even the AT&T techies couldn't tell me that. I asked them about the network changes that have been going on. We have noticed that the name of the network has been changing over the last week fro "umts-AT&T" to "3G AT&T" to now just "AT&T" so I knew there were changes. But when i asked AT&T specifically, they couldn't tell me. Not surprising i guess.
My battery statement was more of an assumption I guess. it was my understanding from my past with the hermes that when the phone went into H mode the radio would take more battery power. and that is why the OS settles back into straight 3G mode in between downloads. Do you know if that is true on the Kaiser. What kind of battery life do you get in the HSUPA mode?
Click to expand...
Click to collapse
No offense directed a KD8DNS, but the At&t Techs only know what their magical screen tells them, or if they are the few with brains, it's what they've overheard and learned in addition to the screen.
I worked a LOOONG time ago as a CSR for Voicestream, the Call Center people don't know item one on where the network is being expanded at what time. They have to wait for the "screen" the be updated, which can take a while.
OH and the fact there it phone says "H" now, is a good thing.
I've had "H" on my Tilt since the first time I powered it on last October. Even my 1 week stay in Pinellas County FL didn't leave me with an E/G.
As far as battery life is concerned, it is true that 3G/HSDPA will deplete your charge quicker that Edge. The way I get around that is using KaiserTweak to automatically kill my data connection after 1 minute of inactivity.
The data tweak combined with a nice low-power radio allow my phone to standby for 3-4 days.
Push Email and online IM with HSPA kill a battery in about 6-7 hours for me (stock Tilt rom/radio). I'm sure that if you only use data when you need to, it's not a big deal, but data being used pretty much all the time is killer compared to EDGE.
I've tried to stick with HSPA a few times rather than having to switch back and forth, but the battery life sucks (again, with push email and IM online) and the phone stays about 38c all the time at 'idle'. EDGE it's cold as ice all the time and the battery lasts about 24h.
I'm updating rom/radio soon, perhaps it is better with other radios.

This is a problem...

I just did a speed test with a 100K file and look how bad the results were:
36kb/sec
2.367 latency
22.066 d/l
Please advise!
Them's GPRS speeds.
What signal do you have?
Does your network support HSDPA?
Even if they do, is it enabled on your contract?
Speeds are affected by an awful lot more things than just what phone you have.... like how busy your network is in the area you're in. the more people online, the lower the speed you'll get.
Seems to me, you may just have a GPRS signal.
crap! I'm just on hold calling Orange now, just upgraded my call-plan so maybe HSDPA has not been activated yet...?
Just spoke to Orange and they said that as my sim card was only activated yesterday at 5:30pm, it's possible that 3G is not yet working on my sim even though it shows up as activated on their system. So I need to wait until tonight, then test again...
Any other Orange users have this happen to this? How annoying.
it's fairly normal.
The sheer amount of systems that need to be updated to get everything working is staggering.
It took t-mobile 3 days to get everything working correctly on my SIM.
It's normal in the UK sadly, just be patient and it will come.
I just spoke to another guy from Orange and he said that it should have been transferred by now and that I need to take the battery whilst the phone is on to do a soft reset - I thought pressing the little red button did a soft reset? If this doesn't work he wants me to call back to configure the internet settings manually...
Anyway, I shall wait. Just to be sure, aside from 3g being enabled on the phone there is nothing much else to do is there? When I switched it on after the rom upgrade it detected Orange settings and said it configured accordingly. Sometimes the symbol says 3g, somtimes it says G.
Is there anything I can do/check in the meantime to make sure this is a network issue for sure?
Sorry if this is long-winded.
Just press the little red button for a soft reset. You could check Settings - Connections - Advanced Network, if HSDPA/HSUPA is enabled. And if you can find the Orange mobile internet settings online, you can check Settings - Connections - Connections, to see if your Diamond's mobile internet connection settings are correct. Else call back to configure them manually. Once you're properly connected you should see the 3G or H icon. After that you can compare your results here, if you want. Please remember that your actual speed depends on a few factors, including your Radio version.. Good luck!
Thank you both for your kind help.I shall take into all into consideration. In the meantime, I shall wait until tonight (when everything should have been transfered to my sim).
S.

No 3G since FRF83

Any solution?
Only GPRS/EDGE does work, if 3G is available, it disconnects automatically until 3G isn't available.
Solution: Set to 2G-Only :-(
Anyone has the same problem?
I didn't have this problem with FRF 72.
Provider: Sunrise Switzerland
Radio: 32.36.00.28U_4.06.00.12_7
Have you tried going into your phone settings from *#*#4636#*#* and setting it to wcdma only? I did that on mine not too long ago and no more dropping to edge for me!
-------------------------------------
Sent via the XDA Tapatalk App
andi86 said:
Any solution?
Only GPRS/EDGE does work, if 3G is available, it disconnects automatically until 3G isn't available.
Solution: Set to 2G-Only :-(
Anyone has the same problem?
I didn't have this problem with FRF 72.
Provider: Sunrise Switzerland
Radio: 32.36.00.28U_4.06.00.12_7
Click to expand...
Click to collapse
does it lose complete signal? or does it show 3g still but just not doing anything?
Mine was working at first after flash. Then at about 2am it just kept trying to load then times out. Still shows 3g but just dont do anything. Im hoping its just tmobile messing with their towers... I dont see why it would work at first then not now..
The problem is, that i can only have a internet connection, when the phone is logged in into a gsm or edge network.
as soon as wcdma is available, the phone disconnects from the internet.
the signal is always available, but it looses the internet connection when it changes to 3G mode.
when the phone changes from 2G->3G mode, i see for 1s the 3G icon and then no icon will bi there.
when it changes back from 3G->2G, the EDGE/GPRS icon is visible again.
andi86 said:
the signal is always available, but it looses the internet connection when it changes to 3G mode.
when the phone changes from 2G->3G mode, i see for 1s the 3G icon and then no icon will bi there.
when it changes back from 3G->2G, the EDGE/GPRS icon is visible again.
Click to expand...
Click to collapse
ok thanks for clarification. My problem is different. I think related to phone company.. I still show the 3g signal and even have bars, but the pages dont load and eventually gives me the check your service and try again alert....
So Im hoping soon its working again for me... And I hope you as well figure it out.....
Thank you Good luck!
Had the same issue after update, did *#*#4636#*#* and noticed I was set to GSM only. Set it to WCDMA preferred and now it's good.
Thank you very much, thats the solution!!
Andi
ezhangin said:
Had the same issue after update, did *#*#4636#*#* and noticed I was set to GSM only. Set it to WCDMA preferred and now it's good.
Click to expand...
Click to collapse
Sent from my Nexus One using XDA App
ezhangin said:
Had the same issue after update, did *#*#4636#*#* and noticed I was set to GSM only. Set it to WCDMA preferred and now it's good.
Click to expand...
Click to collapse
Thank you. Updated to FRF83 this morning and I've had a full 3g signal, just couldn't pull data all day. Could over edge. Sure enough, GSM only was selected.
AT&T N1.
I'm having the same issue on a non-rooted phone on T-Mobile. No 3G after the FRF83 update. Full bars of service and 3G displayed in the status bar. Dropping to Edge only works but there is no data with 3G.
Lost Dog said:
I'm having the same issue on a non-rooted phone on T-Mobile. No 3G after the FRF83 update. Full bars of service and 3G displayed in the status bar. Dropping to Edge only works but there is no data with 3G.
Click to expand...
Click to collapse
Same issue here.
Switching to WCDMA preferred doesn't work for me though.....any help is welcome
I think it's a hardware problem with a lot of N1's.
Mine was ok the first 2 months, and later, 3g not working. This is driving me crazy ):
I have tried everything. Change the simcard, I did a reset of the data with my telcon, and nothing happens.
I've seen these problems on many N1's.
I hope google / htc release a fix for this problem.
Lost Dog said:
I'm having the same issue on a non-rooted phone on T-Mobile. No 3G after the FRF83 update. Full bars of service and 3G displayed in the status bar. Dropping to Edge only works but there is no data with 3G.
Click to expand...
Click to collapse
how bout checking your bands in the service menu. so *#*#4636#*#* -> phone info -> press the menu key for more options -> select bands -> choose one appropriate for your region (ie "USA BANDS").
If all else fails do a factory reset by going to the settings -> privacy -> restore factory defaults.. of course do a backup/sync/whatever before just to make sure you can get all your apps back.
There's other ways to do a factory reset via the bootloader .. its under recovery and you press up volume or the trackball I think and you can just select all the clear/erase settings there and that should clear out everything on the phone's internal storage.
The factory reset worked for me (via bootloader) when I upped from update-1 to FRF50 and didn't have any data icon next to my signal strength. Could call out but couldn't get data.
Hope that helps.
jasonpich said:
I think it's a hardware problem with a lot of N1's.
Mine was ok the first 2 months, and later, 3g not working. This is driving me crazy ):
I have tried everything. Change the simcard, I did a reset of the data with my telcon, and nothing happens.
I've seen these problems on many N1's.
I hope google / htc release a fix for this problem.
Click to expand...
Click to collapse
Check your APN settings. Do a full factory reset from the bootloader. If nothing works you should call tech support again. Most 3g issues where you have issues with connecting are service/signal level related. I *****ed early about my 3g issues on tmobile and it was the network as they've pretty much gone away with improving the backhaul in my area for HSDPA+ or updates to the phone's radio.
HTC is really really really cool about swapping phones and repairing them. If you feel you have a nexus that has hardware issues call them. I did this 3 times already (one time for minor cosmetic issues with the refurb they sent) and I couldn't be happier about how willing they were to replace/repair the phone. It turns out I really didn't have any issues with them at all.. with any issues with hardware from the second refurbished phone. It was service or software related and I'm happy to say with updates/tmobile service improvements I couldn't be happier with this phone.
blisk said:
Check your APN settings. Do a full factory reset from the bootloader. If nothing works you should call tech support again. Most 3g issues where you have issues with connecting are service/signal level related. I *****ed early about my 3g issues on tmobile and it was the network as they've pretty much gone away with improving the backhaul in my area for HSDPA+ or updates to the phone's radio.
HTC is really really really cool about swapping phones and repairing them. If you feel you have a nexus that has hardware issues call them. I did this 3 times already (one time for minor cosmetic issues with the refurb they sent) and I couldn't be happier about how willing they were to replace/repair the phone. It turns out I really didn't have any issues with them at all.. with any issues with hardware from the second refurbished phone. It was service or software related and I'm happy to say with updates/tmobile service improvements I couldn't be happier with this phone.
Click to expand...
Click to collapse
Thanks blisk, but the thing I don't understand is why Blackberry 9700 with T-Mobile bands, doesn't have problems at all ?
By the way, I rooted my phone , so the thing with the warranty it's complicated
I had it happen last night at work all night, but when i got home i checked my wife's tp2 and it also was doing the same thing so for levity wasn't the phone but tmobile. They started worming the same time also.... I think its tmobile.
Hello, I had the same problem with my imported n1. I'm using the tmobile version non rooted fully stock manually updated to frf83. I did a *#*#4636#*#* and selected wcdma only, rebooted and couldn't connect to my gsm network. Went in again and did a wcdma preferred, rebooted, and I works better, still changes fast to edge and G, but less often, I'm still trying it but I have high hopes its gonna be ok
Mmmm i did have problems with 3G too after pushing FRF83, but i found out that for some reason the APN settings weren't set correctly after the update. In my case the port setting after the proxy of the APN wasn't set, i changed to the correct value and it worked.
In conclusion, check your APN settings.
Just went from FRF72 to FRF83 and it's working fine.
I'm currently set to GSM auto (PRL) in the *#*#4636#*#* and I didn't change it to that after putting on FRF83.

Resetting 'band' setting changed from test *#*#info#*#* menu?

The short:
I changed the "Select radio band" setting in the test menu (*#*#info#*#*) and it screwed things up.
I wiped and reflashed CM12.1 - but it didn't reset that setting (it's still borked).
Does anyone know where it stores that setting, or how to reset it somehow?
The long:
Initially in CM12.1 I was having problems staying on LTE - it always fell back to 3G and stayed there.
So tried this band change that someone who had the same problem suggested.
Now, every option I try is great for LTE but says "cellular network not available" and I can't make calls.
The exception is "Cellular" which I can make calls but only get 1X data.
These are the options in the menu:
"JAPAN Band (WCDMA-800/WCDMA-IMT-2000)"
"USA Band (GSM-850/PCS-1900/wCDMA-850/WCDMA-PCS-1900)"
"Cellular (800-MHz)"
"PCS (1900-MHz)"
I don't know what it was before and I can't see figure out how to tell what it currently is set to.
I just want to flash back to stock so things work again, but if this setting doesn't get reset then I don't know if that will work anyway.
Any chance settings like that are stored on the SIM card?
try to re-flash radio only
masterchapter said:
try to re-flash radio only
Click to expand...
Click to collapse
Worth a shot, but doesn't seem to have helped.
Try the instructions here: http://forum.xda-developers.com/showthread.php?p=57778872
I seemed to have luck when I made the changes according to this post and then immediately ran the ping test. I don't know if the ping test really did anything to help but I've had cell service since following these steps.
mh0520 said:
Try the instructions here: http://forum.xda-developers.com/showthread.php?p=57778872
I seemed to have luck when I made the changes according to this post and then immediately ran the ping test. I don't know if the ping test really did anything to help but I've had cell service since following these steps.
Click to expand...
Click to collapse
Unfortunately that's what I did initially. The setting in that link ("Cellular") made my calls work, but I could only get 1X data.
So somehow by just flashing and reflashing different things (including failing to reflash to stock), it's back to where it was when I started.... which sucks, but is at least useable. Calls work and data works, but the first time it has to drop back from LTE to 3G, it get stuck in 3G forever (until airplane mode). Super sucks since it's my primary home router tethered. I have to airplane mode like 5 times a day.
Just in case someone else ran into this problem, I ended up getting a new sim from Verizon and everything's working now finally. It still says "000000" when it's in 3G, but I don't care about that - it works and it goes back to LTE when it can, rather than staying on 3G forever.
Works for Moto X play - should work for others too..
I too did the same mistake. Changed my Band to "USA" and couldn't restore to previous despite Factory reset.
The SIM 1 went into 4G data only (No voice) , didn't recognize 2G & 3G network for any sim.
However Sim 2 worked fine for 2G,3G & 4G.
i came across a thread in XDA, and after breaking my head over how to execute it, I finally did it.
I have written a brief guide to it. Here's the link.
http://forum.xda-developers.com/moto-x-play/help/network-band-changed-to-usa-t3278614#post65991684

Categories

Resources