Hey everyone!!
Did anyone manage to connect his HTC Wings via Bluetooth to the PC and Sync it with WMDC?
It works with cable but not Bluetooth (BL).
I appreciate comments.
Thanks
A.Bagatov said:
Did anyone manage to connect his HTC Wings via Bluetooth to the PC and Sync it with WMDC?
Click to expand...
Click to collapse
It worked pretty easy on my S730. Make sure you enable BT on the phone and your computer. Pair the PC with the S730 and start ActiveSync on your mobile. Select the option 'Connect via Bluetooth' and that was it (for me).
you seem to be using activesync, however i use windows mobile device center with windows vista x32... so the procedure is different and much more problematic it seems... not just with the s730 but with all wm devices
A.Bagatov said:
you seem to be using activesync, however i use windows mobile device center with windows vista x32... so the procedure is different and much more problematic it seems... not just with the s730 but with all wm devices
Click to expand...
Click to collapse
I use Windows Vista Business (32-bit) and I needed to upgrade Mobile Device Center. It works without any problems afterwards. The only disadvantage is that I need to manually connect on my phone, before it starts synchronizing. I would rather have it syncronized whenever it is near my laptop.
it doesnt work for me. bluetooth is turned on in both devices.
does anyone have any suggestions?
i have the toshiba bluetooth stack software, do you use that too??
I had the same problem. Open you WMDC and go into Mobile Device Settings and select Connection Settings. Under Allow connection to one of the following: change the selection from Bluetooth to COM7.
Then open your device and set up your bluetooth connection again. You should see Activesync now.
You are most likely using the Toshiba Bluetooth Stack instead of WIDCOMM.
IT IS NOT WORKING
AAAAAAAAAHHHHHHHHHHHHHHHHH
this is so STUPID
when i try to set up on my phone then it says "you have no partner for activeysnc, get one?"
i say YES and choose my computer
then i can select a port a one point and i CANT select 7
whats the solution!=?!
From your response I think you are trying to set the COM port on your device but you should be changing it in Windows Mobile Device Center.
I'll go step by step in case I was not clear.
1- Disconnect your Wing from your computer.
2- Open Windows Mobile Device Center
3- The only option should be "Mobile Device Settings"
4- In Mobile Device Settings you should have two option Connection Settings and End a partnership, select Connection Settings.
5- Under the second check box "Allow connection to one of the following" there is a drop-down box which should currently read "Bluetooth". In the drop-down box change that selection to COM7.
Note: If COM7 is not available, then I suggest you uninstall your Bluetooth device drivers and then reinstall them.
6- Close Windows Mobile Device Center
Now return to your device.
Delete any existing Bluetooth connections to your computer. and reestablish your Bluetooth connection. You don't need to change any COM settings on your device. Just establish your connection and you should have the Activesync option once it is reconnected.
This is under the assumption that you are running the Toshiba Bluetooth Stack on your computer. If you are and it doesn't work, I'm all out of ideas.
I should have specified that as of Step 2 above, this is all done on your computer not your smartphone, i.e. HTC Wings.
Your problem with Bluetooth is on the computer not the device, most likely.
this doesnt work... i did all the things like u told me on the computer.
then i go to my phone and try to connect from activesync via bluetooth and it says that no computer with a partnership could be found?? even though i actually made bluetooth partnership with my pc. when i added my pc to my bluetooth devices list on my HTC it told me that my pc supported 2 services: stereo audio and com port. i ticked com port... it doesnt seem to help.
on my pc, when i open the bluetooth stack software from toshiba i can see my phone has a partnership with my pc. but it has a network symbol on it.. is this supposed to be like that? ah this is so frustrating? any suggestions?
The only difference I see between your set up and mine is that I don't have a connection appearing on my computer.
So when you open your Bluetooth Settings on the computer, I don't have a saved connection with my Smartphone. The only place I see a connection between my computer and my device is on the device itself.
So my last suggestion is to delete both connections. The one on your computer and then the one on your device.
Open your device and reestablish a connection from your device to your computer. You will be asked to enter the password on your computer but when you open your Bluetooth Settings, you may not see a saved connection.
Also, go back and make sure that in Windows Mobile Device Centre, the connection is for COM7 and has not reverted back to Bluetooth. What you described has only ever happened on my computer when the connection was not set to COM7.
Something currious happened with my device when I was reestablishing my Bluetooth connection, which may be of interest to you.
I erased my original Bluetooth connection and while reestablishing it my device was also connected to my computer with the USB cable. When I paired the device, there was no option for ActiveSync. I disconnected my device and then started the Bluetooth pairing over and this time ActiveSync was available.
Does this help?
Any of you guys who have sucessfully pairedd WDMC in Vista with S730 over bluetooth use original MS out-of-box bluetooth drivers?
I've only used the Toshiba and Widcomm Bluetooth Stacks and have been able to sync with both on Vista.
dagobert_29 said:
The only difference I see between your set up and mine is that I don't have a connection appearing on my computer.
So when you open your Bluetooth Settings on the computer, I don't have a saved connection with my Smartphone. The only place I see a connection between my computer and my device is on the device itself.
So my last suggestion is to delete both connections. The one on your computer and then the one on your device.
Open your device and reestablish a connection from your device to your computer. You will be asked to enter the password on your computer but when you open your Bluetooth Settings, you may not see a saved connection.
Also, go back and make sure that in Windows Mobile Device Centre, the connection is for COM7 and has not reverted back to Bluetooth. What you described has only ever happened on my computer when the connection was not set to COM7.
Click to expand...
Click to collapse
there is the problem: "You will be asked to enter the password on your computer but when you open your Bluetooth Settings, you may not see a saved connection."
because as soon as i enter the bluetooth password on my phone and computer, there appears a bluetooth connection in the manager from toshiba. this connection has a "network" symbol and the services offered are com port and stereo audio. thats not much is it? and also when i click "connect" an error comes up.. connection couldnt be established or something.
i hate this. how can be a SIMPLE task so problematic?
toshiba drivers are working fine. send and receive works. and my phone is fine too. the wmdc work fine as well via USB. i also installed the wmdc UPDATE..... wtf right?!
Hey A.Bagatov,
I'm at a complete loss to understand why you can't get WMDC to work with your phone over BT. You've done everything I've done but unlike you I was able toe stablish the connection.
The only other thing I can think of is to download the latest BT drivers from Toshiba. But before you install them, make a copy of the TosBtChk.dll file and once you've completed the installation of your new BT drivers, replace the new TosBtChk.dll with the one you saved. This will stop you from receiving the trial period notification.
If that doesn't work, then maybe replace your Toshiba BT stack with the Widcomm stack. You'll need to locate a version compatible with your computer.
i would like to get widcomm and get rid of the problems.
so where can i get the widcomm stack? and how do i figure out if its compatible with my laptop?
its sony vaio
A.Bagatov said:
i would like to get widcomm and get rid of the problems.
so where can i get the widcomm stack? and how do i figure out if its compatible with my laptop?
its sony vaio
Click to expand...
Click to collapse
You have to understand Widcomm is not a free replacement for your MS drivers. Its commercial and it can only be obtained with some BT hardware, not as stanalone product AFAIK. As that, it is a bit complicated to make it work with unsupported device (but quite possible). And where to get it? Generally, if you are able to pirate, you are also able to google.
However, I assume you have legal OS installed on your Sony laptop - why not to tell MS they BT drivers SUCK A BIG TIME? Go tell them its crap that does not EVEN WORK TOGETHER WITH THEIR OWN UTILITIES.
Call 1-800-MSSUCKS
A.Bagatov said:
i would like to get widcomm and get rid of the problems.
so where can i get the widcomm stack? and how do i figure out if its compatible with my laptop?
its sony vaio
Click to expand...
Click to collapse
I've also got a Sony Vaio, SZ45, and on the Notebook Review forum, there is a thread that discusses replacing the Toshiba BT stack with Widcomm, which you can get free of charge. The thread offers a modified file which should be sufficient to enable Widcommon your laptop. Here's a link to the general forum http://forum.notebookreview.com/forumdisplay.php?f=8
mpattonm said:
You have to understand Widcomm is not a free replacement for your MS drivers. Its commercial and it can only be obtained with some BT hardware, not as stanalone product AFAIK. As that, it is a bit complicated to make it work with unsupported device (but quite possible). And where to get it? Generally, if you are able to pirate, you are also able to google.
However, I assume you have legal OS installed on your Sony laptop - why not to tell MS they BT drivers SUCK A BIG TIME? Go tell them its crap that does not EVEN WORK TOGETHER WITH THEIR OWN UTILITIES.
Call 1-800-MSSUCKS
Click to expand...
Click to collapse
Microsoft are not the developers of the Widcomm Bluetooth Stack, it's owned by Broadcom. It can be obtained for free, however, you're right in saying it may not work with non-Broadcom hardware. In A.Bagatov's case, the issue is with Toshiba not Microsoft. They are the one's who developed a driver that is not always compatible with non-Toshiba products.
According to other posts I've, the Microsoft generic Bluetooth drivers would appear to work just fine with Windows Mobile devices, however, I was unable to get it working and did not pursue the matter any further once I was able to get the Toshiba BT Stack to function.
I can sympathize with your frustration, but your post does not help him solve his problem.
Related
I just bought an Asus M6VA laptop (called Z70 something in the US), and it has built-in Bluetooth. I can connect with the serial port OK, I can use the Dial-Up Networking to surf the net with my laptop and the BA as the modem, but I'm unable to get AS working. I have AS over BT working with my office computer, that has a Logitech DiNovo Media Desktop bluetooth, with Widcomm stack. But the Asus has a Toshiba stack with a totally different setup, and I can't get it to work.
The Widcomm stack sees AS and even an audio gateway, so I can use the PC as a handsfree device for my BA (even though the sound's rather terrible), but the Toshiba stack only sees a serial port and DUN on it. i would appreciate any pointers and help!
have you set up active sync on your laptop to connect via bluetooth.you have to click on file conection settings and select allow connection to one of the following and then select the com port your pocket pc is using.also when you setup your pocket pc to connect to your laptop it gives you the option of serial port but you also have to have active sync selected aswell if it does not show up then press refresh.let me know wat happens.
I tried again, and when I connect the serial port, I see "Microsoft ActiveSync cannot recognize this device for one of two reasons " and then it suggests that it wasn't connected properly, or that it isn't a PPC or smartphone.
I have the serial port on the PC set to Com6, and AS is set up to allow syncing through that port. On the PPC I have outgoing port Com 0 (just about the only port I could get it to accept, but I tried one other, I think it was Com 9, and that didn't help). I have done a bunch of refreshes but I can't see active sync as an available service on the laptop. I belive that's the problem, since I could see that on my office computer, and that connected and synced without problems.
In AS on your laptop delete any previous partnerships with your PDA. If possible, delete any laptop partnerships in AS on your PDA as well. On your PDA, go to Settings -> System -> Bluetooth Settings. Choose to start AS setup...
It sounds like your laptop may be using the MS drivers... There should be an option to make your laptop Discoverable, but I'm not very familiar with the MS stack... more familiar with the Widcomm. Look for something like Advanced settings in the left window pane...
Let us know if any of that helps!
I have tried that , but clicking on the Start button gives me a window "Please bond with other Bluetooth device which supports serial port or Active Sync profile as your AS partner". And I have already bonded! Bonding again doesn't change anything.
http://episteme.arstechnica.com/groupee/forums/a/tpc/f/579009962631/m/519002845731 use these instructions that is what i did and it worked fine.let me knw
Nope, it doesn't work at all. Like I said in the first post, this is not a Microsoft stack, it's a proprietary Toshiba stack, and it doesn't have any of the setup windows or settings that this guide mentions.
You've probably thought of this....
Maybe you need to manually create a serial port to your PDA... When you paired the PDA to the laptop, what services were you offered? If Serial port is available, create the connection, note down the COM#. With BT started, in AS allow synch via new BT COM port...
Yes, I have tried that, and it didn't work.
I finally managed to do it! I found a way to use the Micro$oft BT Stack instead of the Toshiba one, and now I'm finally set up for AS over BT with the guide mentioned above. Thanks!
I like to sync my Diamond with my Vista-computer and " Center for Windows Mobile devices" through Bluetooth.
I have a working connection with USB already, but want to skip the cable.
I can pair the computer with my Diamond but the only services I get on the Diamond is "wireless stereo" and "serial port".
Been trying to read every instruction on both the bluetooth connection in Vista and on the Diamond but it seems I cant get the service-choice I need to be able to sync my outlook and so on.
Any suggestions on how to get my bluetooth connection working?
Have a look at the link below for links to a pdf download which has an in depth solution to the problem you're having. It's specifically for the Toshiba bluetooth stack and it works if you follow the instructions carefully. If you're not using the Toshiba stack, I think it should still give you sufficient clues to configure the bluetooth ports to work with activesync.
http://forum.xda-developers.com/archive/index.php/t-412836.html
studz said:
Have a look at the link below for links to a pdf download which has an in depth solution to the problem you're having. It's specifically for the Toshiba bluetooth stack and it works if you follow the instructions carefully. If you're not using the Toshiba stack, I think it should still give you sufficient clues to configure the bluetooth ports to work with activesync.
http://forum.xda-developers.com/archive/index.php/t-412836.html
Click to expand...
Click to collapse
Thanks for the link but when I get to page 11 step 16 in the pdf it says you should get wireless stereo and Active sync. I get wireless stereo and serial port as my choices.
Don´t know if that´s because I use Vista and Center for Windows Mobile Devices (The new version that has replaced Active sync in Vista and that should make it soooooo easy to connect mobile devices instead of Active Sync.
I'm guessing you're using the default Microsoft Bluetooth stack with Vista? If so, ActiveSync should be available when you pair your phone with your PC. If not, check the Services tab for the phone in Vista's BT manager applet, it may need to be ticked in there.
I use BlueTooth with WMDC all the time with my Diamond and it was as simple as pairing then going into ActiveSync on the phone and selecting Connect via Bluetooth.
I´m not sure what bluetooth stack I´m using. I think it´s Toshibas but how can I check that?
I had to install Toshibas application to get the drivers for my bluetooth device and I think a got the stack at the same time.
Is there a way to shift stack if I use Toshibas instead of Vistas default?
Please take a look at the attachement to see my gui for bluetooth, and the Center for MobileDevices (Instead of Active sync) on my Vista machine, and what happens when I connect my Diamond through Bluetooth. Sorry about the language but it tries to install the Diamond as a Bluetooth modem and that´s the only thing I seems to be able to install.
I've spent several hours attempting to get this working, I've even bought two new BT dongles for my computer for testing.
Is it at all possible to get activesync working over BT on the diamond? Can't seem to get the ActiveSync profile offered... Neither on my PC or my phone!
audiophil said:
I've spent several hours attempting to get this working, I've even bought two new BT dongles for my computer for testing.
Is it at all possible to get activesync working over BT on the diamond? Can't seem to get the ActiveSync profile offered... Neither on my PC or my phone!
Click to expand...
Click to collapse
Same happend to me until I found the right settings after that I just get irritated when my cable connection doesn't work, in other words I just use it whitout even nowing what the settings are, maybey I can help you if you tel me your settings and show some screendumps, after that I can show you some screendumps whit a working bluetooth connection.
Ps I am not giving any garanty just want to keep my own bluetooth connection
Willem
It works fine for me with Mobile Device Center. Remember to enable BT connection on desktop Activesync options, or else the profile won't appear when you pair with the phone.
I've never got BT/AS to work either (and I've spent days trying), as you say, I never get offered the AS service.
I did see it *once* on the Diamond when I was trying to connect another service (maybe Obex) but I didn't realise how important that was at the time.
I'm using XP/SP2 with the Toshiba stack but I've tried the BlueSoleil stack also with the same result.
I'm guessing this is a problem with the Diamond as I can happily connect with my Artemis via BT to the same laptop
Mee too, I saw the AS-service ONCE, but never ever again.. .:'( Tried 3 dongles and probably 6 different stack implementations.
I'm using XP as well, are the only success stories related to Vista?
Never seen it.
A bad-developed thing with MS and activesync, too bad.
I don't now how your guys try to connect I just can tell how my connection works flawless.
First of all and most important problem whit me was that I have to use the phone to make the connection and not the pc/notebook offcourse you have to allow active sync to acces your phone, in my case this is is found at file connection and allow conection for a compoort in my case com7, then I switch bluetooth on at my phone (and not try to sync straight away cause this results often in a faillure ) and then connect true bluetooth at my phone using the comand connect true bluetooth at active sync at my phone.
One of the strange things which have to set is "All connections use this connection and there is selected "USB" this maid seems trange but I believe the compoort is a virtual one which is used to connect at USB for that reason you have to add a compoort before making your connection, if done right your Diamond will ask for it as soon as you setup the bluetooth connection, the last thing can be wrong cause I don't remember quite well how I did the setup of that part, just because I never use any other connection anymore seems I mannaged to get it working.
This way I can even use it as a wireless webcam which can make you do funny things, the danger of it is when some good programmer makes a virus which allow to setup that connection remotley, aswell the connection whit pocketcontroller I don't want to think off what would hapen if someone manage to get controll of my phone.
Don't now or this is helpfull if any questions feel free.
Willem
On my diamond the only service I can find on my laptop is:
Serial Port
Wireless Stereo
AS set to use the same port as the incoming port in my bluetooth manager...
If you set COM ports right, you tie Diamond with PC using Diamond's ActiveSync. Start/Programs/ActiveSync, the Menu|Connect via Bluetooth. It should ask you now to make a new connection. Tap yes, it will search for BT devices. Choose your PC. If you did everything all right, now you will be connected.
(this may be obvious but I had some problems at start; I thought you initiate the connection on PC)
kosherpig said:
(this may be obvious but I had some problems at start; I thought you initiate the connection on PC)
Click to expand...
Click to collapse
Yes... But what to do when this fails? Anyone ever encountered the "no activesync profile" problem and actually solved it?
audiophil said:
Yes... But what to do when this fails? Anyone ever encountered the "no activesync profile" problem and actually solved it?
Click to expand...
Click to collapse
I gues if there is no active sync profile yet you have to create one what maid be possible aswell is that your settings under active sync/options at your phone where you must selct the options which you want to be syncted, if nothing is selected there it will make a connection but will not sync.
This worked for me
To Async using MICROSOFT Stack do the following:
a. open Control Panel and open Bluetooth Devices
b. click Add and add your device. go to Options and mark "Allow Bluetooth devices to find this computer" and "Allow Bluetooth Devices to connec to this computer". you can also mark other options as desired.
c. go to COM ports and add an INCOMING port. it will choose a port for you automatically.
d. go to WMDC/Connection Settings and mark "Allow connections to one of the following.." and choose the port you created.
e. go back to Devices and choose your PDA. choose Properties and go to Services. there you should see all services your PDA provides. one of them should be Active Sync Bluetooth Service. mark it and click OK. your comp and PDA should connect and disconnect a few secs later.
f. on your device, open ActiveSync and under Menu choose Connect Via Bluetooth.
I just provide my solution.
I use IVT BlueSoleil to manage my BT dongle. After installed, the BT dongle could be recognized as a COM port on the PC. Check through the PC device manager to know what the port number is, then adapt in Activesync, select "Allow connections to one of the following", select COM7 in my case.
Enable BT on the Diamond to make it visible to PC, after paring the PC with Diamond, Diamond could recognize the PC provides ActiveSync services.
Go to Diamond's ActiveSync, select connect via BT, PC will automatically accept the connection from Diamond.
P.S I am not a native English speaker, I just wonder if I could make you understood.
netmaomao said:
I just provide my solution.
I use IVT BlueSoleil to manage my BT dongle. After installed, the BT dongle could be recognized as a COM port on the PC. Check through the PC device manager to know what the port number is, then adapt in Activesync, select "Allow connections to one of the following", select COM7 in my case.
Enable BT on the Diamond to make it visible to PC, after paring the PC with Diamond, Diamond could recognize the PC provides ActiveSync services.
Go to Diamond's ActiveSync, select connect via BT, PC will automatically accept the connection from Diamond.
P.S I am not a native English speaker, I just wonder if I could make you understood.
Click to expand...
Click to collapse
I think the majority here isn't a native English speaker, this forum isn't a forum about language but about phones and pda's if someone wants to show how good his/here English is they beter look for another forum.
I think this forum is one of a few where the solution which someone offers weights more then the way its sad, unless its offending.
Untill now (I don't now what I am calling over myself now) I never got any critics at my English which is far from perfect the last thing wasn't nescesary to say even a blindone could see it whitout braille.
hays said:
This worked for me
To Async using MICROSOFT Stack do the following:
a. open Control Panel and open Bluetooth Devices
b. click Add and add your device. go to Options and mark "Allow Bluetooth devices to find this computer" and "Allow Bluetooth Devices to connec to this computer". you can also mark other options as desired.
c. go to COM ports and add an INCOMING port. it will choose a port for you automatically.
d. go to WMDC/Connection Settings and mark "Allow connections to one of the following.." and choose the port you created.
e. go back to Devices and choose your PDA. choose Properties and go to Services. there you should see all services your PDA provides. one of them should be Active Sync Bluetooth Service. mark it and click OK. your comp and PDA should connect and disconnect a few secs later.
f. on your device, open ActiveSync and under Menu choose Connect Via Bluetooth.
Click to expand...
Click to collapse
Worked flawlessly for me as well. Thanks.
hays said:
This worked for me
To Async using MICROSOFT Stack do the following:
a. open Control Panel and open Bluetooth Devices
b. click Add and add your device. go to Options and mark "Allow Bluetooth devices to find this computer" and "Allow Bluetooth Devices to connec to this computer". you can also mark other options as desired.
c. go to COM ports and add an INCOMING port. it will choose a port for you automatically.
d. go to WMDC/Connection Settings and mark "Allow connections to one of the following.." and choose the port you created.
e. go back to Devices and choose your PDA. choose Properties and go to Services. there you should see all services your PDA provides. one of them should be Active Sync Bluetooth Service. mark it and click OK. your comp and PDA should connect and disconnect a few secs later.
f. on your device, open ActiveSync and under Menu choose Connect Via Bluetooth.
Click to expand...
Click to collapse
I was able to sync my Diamond using WMDC on vista using these steps, with a few modifications.
I had to leave my WMDC "Connections Settings" pull-down box on "Bluetooth" for it to work for me. I'm using a USB dongle, this may be why.
On step (e), after opening the "Services" tab and unchecking, then rechecking the "Active Sync Bluetooth Service" box and hitting Okay, my device would be listed as "Connected" on the main Devices tab for a few seconds before disconnecting (about 3 seconds). I had to initiate step 4 BEFORE the device disconnected. So basically I had 3 seconds to start the Bluetooth sync to get them talking. Haven't had any problems since!
-Mike
This is what worked for me, when not able to get the active sync profile.
In settings for "USB to PC";
turned off 'enable advanced network functionality'
My PC and my Diamond didnt show me any services. Because of that it says no device is paired when i want to connect, although my PC is paired.
I use XP SP3 and the Windows BT Stack.
xp SP3 is a problem ?
cuz nothing work for me
Doesn't work for me either.
Using Vista64SP2.
It worked before but eventually stopped working now.
I see ActiveSync on the Phone and on the Notebook.
AS tries to establish a connection for some seconds but cant do it.
//edit:
Ooook, after Firmware-Flash of new o2 Germany v2.03.207.2 everything's working again. *strange*
Sorry I really need to ask. I have been trying in vain to bluetooth files from my laptop to my X1 (R3AA). As of now, my phone can send (or beam) files via bluetooth to my laptop, but not receive anything at all.
Unlike my P1i, the Bluetooth services available for the X1 (showing up on my laptop) does not include the "file transfer service" that was used for exploring the phone's memory stick via bluetooth a la all the other six older Sony ericsson phones that I've previously owned...
I've already:
(i) Checked the allowing incoming beams box in "settings"
(ii) Installed Obex Inbox (but I think that simply is to allow incoming bluetooth beams to get stored in your storage card instead of device)
Is there anything else I haven't done? I right click on my laptop the file after pairing with my X1 and when I hit "send via bluetooth", basically nothing happens. Man, even my old t610i didn't have problems with bluetooth receiving...
it works for me bro.
start > settings > bt > mode > check both boxes! > ok
this will make X1 "visible" for your laptop.
BR!
-mattx- said:
Sorry I really need to ask. I have been trying in vain to bluetooth files from my laptop to my X1 (R3AA). As of now, my phone can send (or beam) files via bluetooth to my laptop, but not receive anything at all.
Click to expand...
Click to collapse
Hmmm... my X1 works well too. Do you have a custom ROM? in case, which one?
so, you select the file, send to, X1 and nothing happen on the screen of your laptop? if so, it is a laptop problem, not X1 problem.
If it would have been an X1 problem, you would have seen a progression bar saying "discovering services available on X1" and then disappearing because of your mentioned X1 problem.
I'll be waiting for your answers to help you!
-mattx- said:
Unlike my P1i, the Bluetooth services available for the X1 (showing up on my laptop) does not include the "file transfer service" that was used for exploring the phone's memory stick via bluetooth a la all the other six older Sony ericsson phones that I've previously owned...
Click to expand...
Click to collapse
Not sure about why your bluetooth is not receiving, but you can make your laptop access your memory stick as a normal folder to browse the files.
Follow these steps.
1. Make sure you have activesync installed on your laptop.
2. Go to activesync on your phone and select connect via bluetooth.
This should establish a activesync connection thro bluetooth, similar to what you get thro a USB connection.
bharat4ever said:
Not sure about why your bluetooth is not receiving, but you can make your laptop access your memory stick as a normal folder to browse the files.
Follow these steps.
1. Make sure you have activesync installed on your laptop.
2. Go to activesync on your phone and select connect via bluetooth.
This should establish a activesync connection thro bluetooth, similar to what you get thro a USB connection.
Click to expand...
Click to collapse
Hmm. doesn't work here,
Vista, Windows Mobile Device Center.
Any clue?
hmm, next time you connect your phone thro usb, let it connect completely to windows mobile device center, then go to Mobile device setttings, and click on connection settings.
Make sure the check box "Allow connections from one of the following" is checked, and "Bluetooth" is selected from the list. I hope this works. Fingers crossed.
Hi guys,
Thanks for the replies, which help steer me in the correct direction. It seems Activesync is responsible for "unlocking" the bluetooth functions (I kid you not). Finally solved it. This is how I did it (based on advice given):
1. Checked all boxes in Bluetooth options in settings: visibility/bluetooth on/authentication passkey required
2. X1 was already paired up with my laptop
3. Connected to my laptop via USB and activesync loaded automatically
4. Opened up "My Bluetooth Places", which is the program that comes with installation of the Bluesoleil program on my laptop
5. Heard a beep on my X1 for the first time when I did this (this was the first time I was connected on USB via activesync AND activating bluetooth AND accessing the bluetooth places folder) - I think this was what activated it in the end - sorry if i'm not explaining it too well here, but it did the trick
Note: Not sure if a few more options popped up in "My Bluetooth places" folder I don't recall seeing bluetooth messaging/contacts there previously. My OS is XP home, using the default R3A rom.
6. I could transfer files via bluetooth already from my laptop to X1...
*I still haven't been able to manage to get within the file directory tree using bluetooth, bharat4ever, which program (and bluetooth service) might I ask did you use to do that?*
Additional thingys: I think it's important to use a proper software for bluetooth file transfers - Bluesoleil is much better imo than that standard Widcomm (oldish as well) program that came default with my laptop.
I was also wondering if I could transfer multiple files via bluetooth and seems like resco explorer can do the trick, though folders can't be sent via bluetooth - tho the contents inside them will.
Hi,
I just bought a Bluetooth dongle for my PC. (Trust Ultra Small Bluetooth 2.1 Usb Adapter 25 M)
The main reasons for buying this was so I could sync without using one of my very spare USB ports.
Another big reason was that I really want to try SideShow.
So, I hooked the thing up, installed it. Works like a charm for most services (files etc). It just doesn't work for two things: ActiveSync (on the phone)/Windows Device Center (on my PC) and Windows SideShow. Yay.
Could you please help me out?
To summarize:
PC with Vista Home Premium,
Trust Ultra Small Bluetooth 2.1 Usb Adapter 25 M,
HTC S730.
Not working for ActiveSync nor SideShow.
x5x_tim
PS: I installed something called "X86-PC Drivers.cab" I found in some thread. That's supposed to be the drivers for the SideShow service on the PC. (I think I installed them, I did not get an error from Rundll32...)
EDIT: what might be of use: I can't get the devices to pair if I use the PC to initiate that. The PC does not find the phone untill I pair them using to phone to initiate.
I don't know about SideShow but I managed once to ActiveSync my Wings through Bluetooth. Just be sure to remove any security restricition on your Bluetooth settings on your device. Like Secure Connection etc... Also, setup a serial port when you connect with your PC and then, at PC ActiveSync settings, at connection settings -> Allow Connections To One Of The Following (Com 4 or whatever). And then, at ActiveSync on your mobile, connect through Bluetooth. Try it and come again if it doesn't work.
Yes! Thank you. It's syncing as I type. That COM4 did the trick!
In the same way, you can have Internet on your mobile through Bluetooth's activesync connection. It is helpful if you don't have wifi on your mobile.