I have a Kaiser with Alex's ultra clean rom installed. It works great with only one problem I have found so far, no bluetooth profiles. I have searched the foums a couple of timees with no luck. What .cab file needs to be installed to get this functionality. I cannot use it as a bluetooth modem or do bluetooth file transfers but bluetooth headsets do work.
josh
I have this same problem, hoping someone can help. I also use alex's rom.
Is this a known problem with the Ultraclean ROM, or have others not noticed this?
Was planning on flashing to the Ultraclean but might wait to clarify this first.
I have a tilt and flashed the factory HTC ROM and it worked OK there but when I went to the UC ROM I lost all of the profiles. I would think there must be a cab of with them in it as Alex's UC ROM is nothing but a stripped down version of the HTC ROM but I have not tried installing all of the ROMS one at a time to determine which CAB it is.
Not sure if this will help, but the following thread talks about adding Bluetooth DUN to WM5/6:
http://forum.xda-developers.com/showthread.php?t=314371&page=3
Post #21 has a file to download. Give this a try and let us know if it works - then we just have to figure out the file transfer.
Actually, I think I need to clarify what you meant by missing Bluetooth profiles.
I have just flashed Alex's Ultraclean HTC ROM and confirmed that I am able to transfer files via Bluetooth to and from my TyTN2, using either my laptop or my N73. So I do not seem to be having problems with file transfer. Bluetooth headset also connects fine.
Don't use Bluetooth DUN so can't comment on that. Not sure what to suggest. I did flash to the new HTC ROM that was released a couple of weeks ago prior to Alex's, and flashed from Orange to the stock HTC a few days before that, so I don't know if that made a difference?
I will restore my device to the base ROM and see if I still have the problem. I install a few cabs and it may be one of them causing the problem. I'll report back...
I restored my device to the base Ultra Clean ROM and still no luck with file transfers. Below is the message windows gives me.
>
The file transfer failed because the receiving Bluetooth computer or device did not respond.
If you sent the file to another Windows XP computer, that computer must be running the Bluetooth File Transfer Wizard. If you sent the file to a Bluetooth device, make sure the OBEX File Push Profile is installed.
<
After flashing the base ROM, did you perform a hard reset before installing stuff?
I read somewhere that this helps to avoid further problems. I have done this after every flash, and have not had any major problems yet.
I have been running on the ROM for several weeks now and this is the only problem I have run into. I did a hard reset of my device last night and got the results listed in my reply above. So to answer your question, yes I did do a hard reset.
Related
Please help. I flashed 2.16.9.x and now ActiveSync doesn't work anymore, it connects all the time. PDA doesn't show activesync syncronization icon.
I tried to flash another versions of ROM, but it didn't help.
The problem may lie with the PC as opposed to the PDA. Have you tried a remove / re-install of AS4.1 on the PC?
Bebbo said:
The problem may lie with the PC as opposed to the PDA. Have you tried a remove / re-install of AS4.1 on the PC?
Click to expand...
Click to collapse
Of course I have. Even I tried on another computer.
vishny said:
Of course I have.
Click to expand...
Click to collapse
Fair enough, I was just trying to help. Perhaps if you had stated that in your original text I would not have provided such an "Obvious" answer. I will leave it up to others now to take guesses as to what you "might or might not have done"......
vishny said:
Please help. I flashed 2.16.9.x and now ActiveSync doesn't work anymore, it connects all the time. PDA doesn't show activesync syncronization icon.
I tried to flash another versions of ROM, but it didn't help.
Click to expand...
Click to collapse
Try to make your computer or laptop restore on earlier date then since it started. I had once this problem i don't know but sometimes it with the system files in computer missing then the problem occurs.
Although my ActiveSync works almost fine after the same rom-upgrade, I encounter its strange behaviour sometimes (rear, not always!) - PDA slows down to a crawl right after you disconnect it from a desktop PC (either USB or Bluetooth). It becomes so terribly slow that it takes 20-30 sec to draw the Comm-manager window! then you better soft-reset, then it works just fine. Why am I... to prove that ActiveSync 4.1 is not quite stable with new ROM version 2.16. There is a bug somewhere, and it has to be reported to i-Mate firmware writers.
Have you followed Microsoft rules about configuring firewalls for ActiveSync 4.1? Does it create a network connection 169.254.2.1 on a desktop PC?
Thank you guys, but I guess my case is harder:
1. I have firewall switched off. I didn't change any setting in computer. I just flashed new ROM.
2. I flashed my original ROM, but it didn't help.
3. I tried to sync on several computers and had the same result.
By the way I cannot return to original ipl/spl, I don't know how to do that.
Today I visited repairing service's office and they've prooved me my device is not broken, it synchronizes succesfully via USB on their computer. :shock:
So, the problem is related to my computer(s). If I'll find something I report in this thread.
it probably has to do with one of the cabs you installed that are on your original extrom or someone elses. Most people who have had problems after the upgrade on an 8125 (Cingular) have installed cingular cabs from the old rom. I had to to figure out the MMS configuration and after I foundthe one that did my activesync no longer worked. after a reflash and only installing some of the default cabs that came with the new rom and manually configuring the mms and gprs I don't have any problems at all.
well maybe it is the version of activesync we are using when this does happen.
I'm running the ROM that came with the Cingular 8125, and it does the same thing ... 1 in 10 times after disconnecting the device from the PC, the 8125 slows to a crawl, and the only way to recover is a soft-reset. 9 out of 10, it works fine.
OS ROM: 1.8.11.1 WWE
Radio: 01.09.11
Protocol: 4.0.13.20
not overclocked
soon to be ROM upgraded (hopefully)
ethorn said:
well maybe it is the version of activesync we are using when this does happen.
Click to expand...
Click to collapse
I use 4.1 for a long time.
I didn't install anything on my pda. It happens even after hard reset. I even tried to flash original rom. In all cases ActiveSync displays "Connecting...", pda even doesn't display sync icon.
I tried to sync with standalone notebook and it was successfull. I'm really shocked why pda cannot sync with my desktop(s). It seems to me it could happen after some windows unattendant updates or something, I'm still investigating...
I have Qtek 9100 and have installed rom 2.16.9 and i also have activesync 4.1 refusing connection to my pda. After some googling i have found this interesting site: http://www.pocketpcfaq.com/faqs/activesync/tshoot-as4x-connection.htm
I did cheks described there and found out that activesync doesnt have any network adapters and/or activity. USB driver installs, but it, again, doesnt generate anything. Maybe problem is there?
Ehhh... I even cannot return to any previous rom version, because there is no rapi for updaters to work with
reverting back to original cingular rom
How would you go back to original ROM using Lokiwiz tool if your active sync was working OK?
Thanks,
Each time I have done HARD RESET--I uninstalled active sync from my computer AFTER DELETING PARTNERSHIP. I deleted PC from Active sync on my 8125. I deleted all files on my computer related to active sync using search.
I then reinstalled active sync 4.1, being sure WINDOWS FIREWALL was off. I went thru all the steps with my TREND MICRO VIRUS PERSONAL FIREWALL EXCEPTIONS listed on http://www.microsoft.com/windowsmobile/help/activesync/default.mspx
and I got it to work (1st install always takes time for calendar)
Hope that helps--it seems ridiculous to have redo all that-but so be it.
I'd like to know how to get back to CINGULAR ROM as I am still in 30 day return window.
Well there is a magical combination of buttons as described in http://forum.xda-developers.com/viewtopic.php?t=37386 (somewhere around 2-4 page):
Voice+Camera + Reset. Colored bootloader shows up. After that you can connect it to usb and run .exe with rom you want.
The problem with me is that i dont use any 3rd party firewall (i have hardware router for my connections)
reverting back to original cingular rom
You don't think there would be a problem going DOWN in ROM'S?
Do I need to UNLOCK again first?
I must confess. I did (i think veeery lucky) sucseded in running activesync. Altough what was the cause i cannot say. I reverted to 1.6.7 version of the rom. and reinstall everyting several times. and reboted several time. and i saying loud magical words. (and deleted checkpoint vpn software that i have installed). AND it worked!
Maybe trouble was in vpn soft, but it worked pre 4.1 activesync. So... Here is my experience.
Boki said:
I have Qtek 9100 and have installed rom 2.16.9 and i also have activesync 4.1 refusing connection to my pda. After some googling i have found this interesting site: http://www.pocketpcfaq.com/faqs/activesync/tshoot-as4x-connection.htm
I did cheks described there and found out that activesync doesnt have any network adapters and/or activity. USB driver installs, but it, again, doesnt generate anything. Maybe problem is there?
Ehhh... I even cannot return to any previous rom version, because there is no rapi for updaters to work with
Click to expand...
Click to collapse
Thank you very much for this link, it helped me to find the reason. It's not new ROM fault. The Microsoft Firewall Client (ISA 2000 component) on desktop blocks communication between PDA and desktop. I disabled it and now ActiveSync works fine.
Thank you again.
Your Are Welcome
After some "unpleasantness" over the weekend, I was forced to completely redo my Wizard. I was using Summiters previous ROM and loved it, so naturally I went with his latest. Everything has been fine and the ROM looks great. I've been fighting with some other software (Wisbar Advance Desktop Beta) but that's irrelevant. The small issue I have that is ROM related is when connected to activesync, I cannot get web connectivity. Cannot web browse, nor can I receive email. As soon as I unplug it, everything is fine. Can someone make a suggestion for a fix? It's probably something stupid I'm overlooking because I'm busy fighting with other software. Thanks.
I have been haveing this same problem since I updated to activesync 4.2.
I am still on the latest factory rom 2.5
I'm using the activesync 4.2 beta version on this machine. I used it fine with the previous ROM.
Also, another thing with this ROM is when copying images onto the device from the computer, it now faults when trying to copy "thumbs.db" files. I have to show hidden operation system files on my PC, un-highlight the thumbs files and then copy the content over. I never had to do that before.
hi
I tried to upgrade my pda2k to 2005, but I get hang
then when I tried again it show this message
http://www.600kb.com/uploads/20aac64ad6.jpg
can i get help please
sarab
Strategies for dealing with radio ROM update 114 errors
I had this problem last week and recovered from it. At first it looked pretty bad, nothing seemed to work. I looked the Internet up and down and in most forums, including this one, people agreed that nothing could be done about error 114, the mainboard of the BA needed replacement, etc.
When I finally did fully recover from this situation, it was from a combination of measures that I took and as I don't really know which one actually did the trick, I'll try to describe all of them even though not all will probably apply to others. Another problem is that I probably won't be able to remember them all, but anyway, here goes:
1) I downloaded the latest full official ROM update from site of the carrier this phone was branded for, in this case T-Mobile. It included a radio ROM, albeit version 1.13.0, not 1.15.0 which is the one I had been trying to flash. I decided it would be best to go back to that official version first.
2) I had been trying to do the radio ROM upgrade from a Macintosh (OSX) under Virtual PC. I have since done several ROM installations (without the radio part) from the Mac/VPC which worked fine, but since people had observed that radio ROM updates seem to be more sensitive than fiddling with the normal ROM, I decided to fire up my "real" PC, which runs WIndows XP, SP2, with Active Sync 4.5.
3) As others had suggested, I made sure that I had my cradle connected directly to a USB port on the computer; before I had been trying to go trough a hub. I also made sure the cradle was connected to the power adapter.
4) I had unlocked my device before to work with a non-T-mobile SIM card, but since I wasn't sure wether or not SIM/Net lock problems might still interfere with radio upgrades, I took my SIM card out of the unit, as well as the SD card -- trying to eliminate as many potential sources of screw-up as possible.
5) I think I tried to set my BA into as much of a defined state as I could by hard-resetting it and THEN invoking boot loader mode. I don't remember whether or not this was possible as the device was not reacting much to anything at the time.
6) On the Windows PC, I opened Active Sync, then went to Connection Settings and explicitly disabled the USB connection. I then quit Active Sync and invoked the Windows task manager (Ctrl-Alt-Del) to check that no other processes were running. Trying to cut out interference as much as poosible ...
7) I then proceeded to flash the official ROM version, which went flawlessly including the Radio ROM, took less than fifteen minutes in all. To be honest, I don't remember which ROM upgrade utility (BaUpgradeUt/MaUpgradeUt_noID) I used ... sorry. I know I tried whatever was included with the T-Mobile download first.
After that, I verified that everything was working again, then immediately flashed Radio ROM 1.15.0 as I had originally intended. This time it went uneventfully.
Hope some of this helps, I know how frustrated you must be at this point.
Good luck!
thanks a lot
i'm going to follow your instruction today.
regards to all
[email protected] said:
thanks a lot i'm going to follow your instruction today.
Click to expand...
Click to collapse
So did you have any luck?
Hi all,
Finally WM6. Great!
But after installing the Tofclock ROM, my device became unstable like many others have reported. So when C_Shekar published his ROM, I installed it.
No problems on stability anymore, but after this upgrade I can no longer use my Bluetooth functions properly.
I can pair with my GPS, but as soon as I try running GPS software the device becomes slow and will reset after some time. After that, only turning bluetooth on will cause a reset, no matter if I'm paired or even using it at all.
So I re-installed the Tofclock ROM, because there I had at least GPS. But now it was no longer working there either.
Today I even downgraded to AKU3.5 and even a 'pre-historic' version of 2003 (1.70) but it does not work anymore for any of the ROMs.
Can someone please help me on this one. I understood from other posts that I'm not the only one, so it's not just my Hima. But I really would like to have my GPS back.
rvdrijt said:
Today I even downgraded to AKU3.5 and even a 'pre-historic' version of 2003 (1.70) but it does not work anymore for any of the ROMs.
Click to expand...
Click to collapse
Which indicates that it is an hardware failure and not a software problem.
Flashing the device with another ROM version does not destroy any hardware at all.
Sascha
Thanks for your response.
But if it is just a hardware problem that can't be caused by an upgrade, how come I'm not the only person experiencing the same issue that started at the same time?
If it was just me it simply could have been bad luck.......
I'm just still not sure of my conclusions, but everything points at the upgrade to WM6. Let this be a warning!
I have not seen any similar reports in any threads before. Can you link us to specific messages?
It is very well possible that it's a software problem. After all you're probably using the same GPS/BT software in all these ROM up/downgrades you tried?
My GPS software is entirely on my SD card, after flashing a new ROM and formatting my RAMdisk it instantly knows my last position. Your software has IMHO probably messed up some file on your SD card that's related to your BT/GPS settings or so. I advice you to format your SD card, reinstall the clean GPS software on it, see if it still misbehaves.
http://forum.xda-developers.com/showthread.php?t=332945&page=17
You also entered a reply back then ;-)
I will re-install my GPS software. However, I've tried other programs as well with the same result (i.e. Speed Sentry). But that might be because I tried it after a first reset. And the reboot also appears when I have a different SD card in the slot.
Right now I'm waiting for my backup battery to be empty. Who knows, a 'real' hard reset might help.
@Maggy
Seems you were right! Removing the battery didn't work so I checked my GPS program's files. I found a recently changed file for the config and after I removed it it seems to work again!
Still a big puzzle why it started when I changed to WM6. But I'm updating my ROM at this moment so I hope to be able to answer the question if it is WM6 related soon.
Thanks for the help!
You're welcome.
And yes, you're right that I replied to that post but my memory is in my PC and XDA, not in my head
It's possible that there's a tiny difference between the way the config file is written in WM6 or WM2003, so switching from one OS to the other messes the file up.
I have the good habit of formatting the SD card when I flash a ROM.
Glad this item looks solved.
Even better: it doesn't look solved, but it is solved.
I went home using my GPS! YESSSS!
Knowing this it's time I start cooking my own ROM......... thanks to all the great people at this forum.
Hello All
After having read the message, I just try TOMTOM 6 with RBT2001 and have the same problem, tomtom is very slow, and after some time soft reset.
And I have this problem with the new ROM: 7.0c.40CS (WM6 AKU 7.0)
And I had no problems with the ROM: 7.0b.40CS (WM6 AKU 7.0)
If this can help you understand the problems ?
I guess you should delete \Storage Card\ttnavigator.bif, then reinstall Tomtom
It's even much simpler: simply delete the \TomTom Navigator 6\navigator.cfg file. You'll have to redo some configuration, but it works great again.
rvdrijt said:
It's even much simpler: simply delete the \TomTom Navigator 6\navigator.cfg file. You'll have to redo some configuration, but it works great again.
Click to expand...
Click to collapse
Good.
Tomtom work again.
Thank you
Hello,
I'm having issue synchronizing my Xperia X1 with my PC using ActiveSync or WMDC.
Powering my battery works but sync doesn't. I tried 2 other USB cables and same problem occur.
I tried different PC but still I have same problem. I event went back to original Stock and this doesn't helps also.
Should I send my device for fix? I have warranty? I can reverse to original Stock and put back original boot loader.
Hopefully they will fix it but if they don't I cannot add custom ROM any more
You can go and get a card reader to have your sd mini read in the pc, I got mine with 5 EUR and it also supports several type of cards. Also keep in mind that read/write speed is faster with a card reader than plugging your device in Disk Drive mode and this can be convenient sometimes
Good luck with the repair. If you revert to stock SPL and to stock rom and if your time of warranty is not up then you should have no problems, although in my country the service center sucks, they try to make you pay as much as possible...
I manage to resolve this issue. I revers back to my stock ROM 6.1 and still I cannot sync. Then I put back radio 1.10.25.18 and it START TO WORK !!!! I can sync now without any problem and it works now with 6.5 ROM and different radio.
This was last step before I want to return it to SonyEricsson service.
Usb problem
Hello,
I'm having issue synchronizing my Xperia X1 with my PC using ActiveSync or WMDC.
Powering my battery works but sync doesn't. I tried 2 other USB cables and same problem occur.
I tried different PC but still I have same problem. I event went back to original Stock and this doesn't helps also.
usb probem
how to update the radio 1.10.25.85 on xperia x1 by the micro sd card? since the usb is not working? thanks!
same as you update your ROM, just rename radio file to KOVSIMG.nbh and update it. Hope this will work for you also.
yes I do this procedure [KOVSimg.nbh] but gets caught in tla loading. WHAT do I do now .thanks!
there is no difference in flashing ROM and Radio, can you maybe check that you do all proceudre correctly? maybe you should download Radio from some other place, maybe is broken
i have the same problem...the battery is recharging but it cannot sync...maybe it has something to do with the version of windows...i was using windows vista and windows mobile device center and it synced and all was ok...but now i have windows 7 ultimate x64 and even though i downloaded the mobile device center it does not recognise the phone when i plug it in activesync mode....it still works perfectly in USB drive mode....but i cannot flash a new rom through the usb method now...recently tried it on a friends pc with windows xp and activesync and worked just fine...any thoughts on that??..
ok. I tried everything. [xperia x1] is not reconhesido by [usb].
neither the radio rom can be clicked. [already downloaded several saiter]. it hangs in louding
I've the same problem occured before but I'm not sure if it's as simple as mine.
All I did was disable "Faster Transfer" under Active Sync radio Button in USB 2 PC (Control Panel), hope it's helpful.
Ok, I'd try this, but I have two questions:
1) can any body give the link to the old Radio rom?
2) I already have a 828x rom installed. is that compatible with the old rom?
life owner said:
Ok, I'd try this, but I have two questions:
1) can any body give the link to the old Radio rom?
2) I already have a 828x rom installed. is that compatible with the old rom?
Click to expand...
Click to collapse
hm, OT post
1) radio selection, don't forget to install a matching rilphone.dll
2) afaik those two (meaning radio rom and normal rom) are not related like that, radios should work in all versions on all roms
it might be, that you suffer less functionality/signal strength when using an older radio version, but that is regionally different and cannot be generalized
hope you find your ideal combo
Best, DK