Problem with update WM6 - Treo 750 - Palm Treo 750 ROM Development

Good morning friends...
I'm from Brazil - Sao Paulo.
I did the download of the updatingfor WM6 straightly of the site of the Palm Australia (version for operator Telstra 1.15 ROW), for a treo 750 version 1.15 ROW of the operator Claro. It was doing the updating and for my unhappiness, it finished the energy. When it returned, the appliance does not go out from that fabric of bootload. I looked for informations in several forums, and found the information of which there was an executable one to continue the updating in the directorate TEMP. I continued with the updating, and came ending it. However, now the appliance does not go out from the fabric of presentation (it arranges with it soon of the Palm). I tried to find some informations in respect, and even I finished appealing, and even I formatted the Palm (Power Reset). I tried to install again, I continue them to myself with the same problem. I checked that there are some updates in which there is possibility to effectuate through the SD itself, which the ActiveSync does not recognize any more the appliance. It recognizes the Windows like ' HTC USB SYNC '.
If possivel, it would like some help, if vcs know any alternative form. Opposite case, I will have to get a beating up to the technical back-up, and it does not enter in the guarantee.
Excuse if there are some mistakes, but it does time that I do not talk in English
From now I thank.

Phew, I managed to decide. I followed these steps what I found in the Internet and it gave right:
1. Using winrar descompacte Updater_anything_anything.exe
2. Find there the archive CHEEIMG_FW.nbh (it has +- 83MB).
3. Format his card for FAT32 (using Windows and reader of card for ex). There is certified what is FAT32, not FAT (16). (obs I formatted mine using the proprio palm with the resco explorer himself).
4. Copy CHEEIMG_FW.nbh for the formatted card.
5. Re-nominate CHEEIMG_FW.nbh for CHEEIMG.nbh
6. put his card in the Treo. Connect the porter in the Treo.
7. Pressing buttons PPT/Media (below the volume) hold tight reset with the stylus.
8. There must appear the fabric of the bootloader (it reddens green blue).
9. If vc did the previous steps correctly he must ask if you want flashar the ROM.
10. Press the red button (power) to confirm.
11. Assist the bar of progress while the Treo is flashado (15 minutes??)
12. After the upgrade, do a hard-reset (reset holding the button power, then arrow 'up' to confirm).
Since it was not letting to pass the archive for SD through the Palm, and tbem have not a card reader, I used a Nokia 6265 that had here, and he gives the option of drive was recognized like pen. I formatted the SD and followed these steps.
Phew, I thought that my Treo had died, thanks guys...

Related

Tera Term for Windows XP?

Do any of you have a program that I could use to sync my phone to my Computer via usb? I've tried several versions of Tera Term with no success. I reached the point where I was ready to pull all of my hair out and then I remembered... I don't have anyway. Oh well. Please help I really want to upgrade my rom but I want to back up the old first. Thanks, Vern.
i think i don't understand what you're trying to do!?
Don't you use ActiveSync for Syncing with your PC?
And wtf is Tera Term???
This is what I'm trying to do:
Originally Posted by kdenninger
To back up the firmware on the MDA to an SD card (a VERY GOOD IDEA if you intend to fool around with new firmware!)
1. Get a 128MB SD card. They're cheap - under $20.
2. Insert said card.
3. Go to http://forum.xda-developers.com/viewtopic.php?t=37386 and download the aWizard utility. CID-unlock your phone. (You only need to do this ONCE, even if reflash in the future.)
4. Get a terminal program that can speak over the USB port. There is a patched version of Terraterm out there, along with a few others. You need a way to connect to the device over the USB port as an ascii terminal.
5. Turn off the phone.
6. Holding the CAMERA key, press the power button for 2-3 seconds. Continue holding the CAMERA key until it comes up in the tri-color screen.
7. Connect the USB cable. Wait until ActiveSync tries to start. CTRL-ALT-DEL Windows and kill the process wcescomm.exe (ActiveSync's communication driver)
8. Now start your terminal program and point it at the USB port. Hit RETURN and you should get a command prompt. You are now talking to the phone's boot loader in terminal mode.
9. Type "r2sd all" and hit RETURN.
10. If you get a security level violation, you DID NOT CID-unlock the device. Go back to step #1.
11. The ROM image (all of it) will be written to the SD card. Several messages will be displayed while this is in progress. Note that this is NOT - I repeat - NOT - a filesystem-formatted dump - it is a RAW image of the ROM with some checksum information included. Anything on the SD card will be destroyed - don't do this with a card that has data on it you care about!
12. You can stick this card somewhere to be used for restoring. If you want to save the image off the card to your computer, stick the SD card in your computer and then dump 128MB of the card starting at the front (the actual dump is about 80mb but will always be less than 128MB, so that's "safe".) You will need a tool like "psdread" or any other tool that can do byte-level I/O to the SD card in your PC's reader for this.
To restore a SD-card image dump to the Wizard:
1. Write the image to the SD card. Again, this is NOT a filesystem - its a RAW image! Unless you saved the image to the card from the Wizard initially you will need a tool that can do a raw write to the SD card in your computer.
2. With the Wizard OFF, insert the card into the SD slot.
3. Hold BOTH the CAMERA and VOICE keys and press the power button for 3 seconds. Release POWER.
4. Look CAREFULLY at the Wizard screen. The backlight WILL NOT BE ON! It will tell you to press the VOICE button if you wish to restore the SD card image. This message only appears for a few seconds and the backlight is OFF! If you wait too long you will end up at the tri-color bootloader screen. Press the VOICE button (if you still have it down, let up on it then press again.)
5. The restore will run. Note that the backlight IS NOT ON during this process! You may need a flashlight (or very bright ambient light) to be able to read the progress meter.
6. When the process is complete it will tell you to press "any key". Do so and you're back in the tri-color bootloader screen.
7. Turn off the Wizard with the power button. When you turn it back on, it will hard reset just as if it was brand new off the firmware you just restored.
Note that this is the ONLY way to recover from a bricked phone if you try to load the wrong firmware file using one of the "forcible" methods (e.g. aWizard) on a non-CID-unlocked phone, and have bypassed the normal protection methods as ActiveSync cannot get back in there under these circumstances.
I strongly recommend that if you're going to futz with firmware, that you get yourself a 128MB card, make one of these dumps, and TEST the restore before you play around. This will recover from almost any botch - the only exception is loading a firmware file via some means (e.g. "aWizard") that the phone cannot execute at all.
Note that I do not know if this will get around the "boot loader version is too high" problem - I'm not willing to try it until I have an official T-Mobile update with a newer boot loader.
This same method for both dump and restore works on the SDA as well.
13. Overclocking the MDA (do so at your own risk!)
Quote:
Originally Posted by Scaw
Use Smartskey, read about it in this article on my HTC Wizard Blog. No specific ROM required, overclocking integrated. You need to download OMAP Clock seperately, it is available from the same article. A small tutorial in PDF format is included in the .zip with Smartskey. Don't forget to remove the ";" (without the quotes) at the beginning of the overclock settings in the configuration file!
How fast you can clock it depends on your device, it's just a matter of trial and error. 240 seems to be safe for the majority of HTC Wizard owners. No need for extra tools to wake overclocking up after a soft reset or standby. I haven't noticed severy battery drain, I can easily use my device a whole day and come home with the batterie well over 50% charged.
It's just a great little program. The integrated overclocking comes as a bonus to the tweak that the program was actualy made for, remapping buttons so you can open the start menu without using your stylus and close programs without using the stylus.
Have a look around on the HTC Wizard Blog, there is lots of other stuff that you may find useful.
And Number 4 is WTF Tera Term is. Thanks.

BlueAngel BootLoader

Hello Everyone,
My BA is stuck at the Splash Screen, I suspect that the Bootloader is corrupt. Does anyone know how to flash it?
try this for whoever get stuck at boot screen or in bootloader mode
1. Download mtty v1.42 from http://files.pdamobiz.com/ROMs/XDA/mtty1.42.rar
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
3. put your device into Bootloader Mode by pressing Power + Record Button and Soft Reset.
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.
imatrix
imatrix's suggestion.
@imatrix
Followed the steps before, and followed them again.. I'm still stuck.
Something interesting happened though:
There are two horizontal stripes across the splashscreen now.
I already tried to flash the OS, It doesn't work with the standard imate flash executable (It used to work before) and now I'm getting a 'MODEL ID ERROR' when I try to flash it using the BAupgrade... executable.
I tried with the MAupgradenoid tool, it flashes but I still get stuck on the splashscreen...
Thanks,
Wadih
BlueAngel Bootloader
Anyone has a way to either dump a bootloader file for the BA (Providing the file of course) or alternatively directives to copy it from another device (From the same make, i.e. Imate PDA2K) ?
Many thanks,
Wadih.
try this
http://forum.xda-developers.com/viewtopic.php?t=49611&highlight=model+id+error
imatrix
@imatrix
imatrix said:
try this
http://forum.xda-developers.com/viewtopic.php?t=49611&highlight=model+id+error
imatrix
Click to expand...
Click to collapse
I did, but as I specifed in me earlier post, eventhough the MAUpgradenoID flashes the files, I still get stuck at the splashscreen.
Interesting point: After flashing witht the MAUpgradenoID, I try reflashing back with the BAupgradeid.. I get the Model Error ID error back..
Something in the BA is wrong, and I believe it may be in the Bootloader. So, is there a way to replace the bootloader itself?
EDIT: By the way, I can't seem to be able to place a WM5 rom instead of the WM2003, although the flashing procedure starts, it quickly ends (i.e. without the percentage bar appearing) and says that the flashing worked successfully... But nothing gets actually flashed.
Many thanks for the help imatrix.
Regards,
Wadih.
hey,
check this out http://buzzdev.net/component/option,com_remository/Itemid,100/func,select/id,38/
but i have to warn you, replacing a booter is very dangerous, anything goes wrong during process will kill your device. so please handle with care.
imatrix
@imatrix
imatrix said:
hey,
check this out http://buzzdev.net/component/option,com_remository/Itemid,100/func,select/id,38/
but i have to warn you, replacing a booter is very dangerous, anything goes wrong during process will kill your device. so please handle with care.
imatrix
Click to expand...
Click to collapse
Thanks for the link, but how do I copy/get a clean boot bin file? (Which app, syntax, etc...)
Cheers,
Wadih.
BlueAngel froze on isalling wm6.5
much respect 2 all.I'm new here.i tried installing wm6.5 on my Blue Angel i tried putting it on a memory card i pressed power reset hold Camera and Record no luck. i didn't noticed this rom is for the Touch Diamond.i opened the file in the memory card and there was many files.i installed a few files i clicked one file and it froze.what i got is message serial on the top the screen and on the bottom of the screen is v1.02.i also tried sync it with computer no luck.can some one please help me and direct me 2 get wm6.1 because when Blue Angel 6.5 i was directed for the Touch Diamond rom.much respect.thanx a million thanx in advance.lol.
---------------------------------------------------------------------------
Learn 2 live & live 2 learn.learn 2 listen & listen 2 learn.Live 2 love & love 2 live.
We live 2 die & we die living.
life is what u make of it
BlueAngel froze on installing wm6.5
much respect 2 all.I'm new here.i tried installing wm6.5 on my Blue Angel i tried putting it on a memory card i pressed power reset hold Camera and Record no luck. i didn't noticed this rom is for the Touch Diamond.i opened the file in the memory card and there was many files.i installed a few files i clicked one file and it froze.what i got is message serial on the top the screen and on the bottom of the screen is v1.02.i also tried sync it with computer no luck.can some one please help me and direct me 2 get wm6.1 because when Blue Angel 6.5 i was directed for the Touch Diamond rom.much respect.thanx a million thanx in advance.lol.
---------------------------------------------------------------------------
Learn 2 live & live 2 learn.learn 2 listen & listen 2 learn.Live 2 love & love 2 live.
We live 2 die & we die living.
life is what u make of it
100/100 work
imatrix said:
try this for whoever get stuck at boot screen or in bootloader mode
1. Download mtty v1.42 from http://files.pdamobiz.com/ROMs/XDA/mtty1.42.rar
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
3. put your device into Bootloader Mode by pressing Power + Record Button and Soft Reset.
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.
imatrix
Click to expand...
Click to collapse
thaks br very good
Hi, I have the problem, that windows does not recognize the Blue Angel any more, so no "WCEUSBSH001" available. Any help??
Thx

Help with wm5 to wm6 upgrade!

I'm dizzy reading all the threads, information overload, so thought I'd just post the question! This is all a bit scary and I'm a complete newbie so take it easy on me... and feel free to dumb everything down as if I were a child.
I live in Australia and have a Treo 750 with Software Version TREO750-1.15-ROW. It seems to be unlocked but still has the Telstra splash screen, although I use it with Vodafone. I want to upgrade to WM6, and from what I can tell I should upgrade using Treo750_2_27_ROW_EN_DesktopUpdater.zip (which I now have). Is this right? Should I skip straight to the WM6.1 upgrade? Are these official/safe?
I am running 32-bit Vista with SP1 on my laptop.
I found instructions on Palm's site here:
http://www.palm.com/au/support/treo750/downloads/wm6update.html
Are those the instructions I should follow? Is that all I need to do? I keep seeing references to the "Bootloader Method" or the "SD Card Method" or the "Cheetah Method". What are all these alternative methods? Which are the advantages of each? I've seen various different instructions, some involving renaming some .nbh file, etc. What is the definitive method?
I saw the sticky thread for the "Cheetah Hard-SPL and SIM Unlocker"... what is that utility for? Are the instructions for it in the download itself? (I didn't see it in the thread) What are "cooked" ROMs and why should I be interested? Where can I find them?
Sorry for the newbieness... thanks so much to all who respond!
upgrade to WM6
If you want to upgrade to the official palm WM6 rom - then you use Treo750_2_27_ROW_EN_DesktopUpdater.zip and it is very simple - just connect the PPC to your computer . (as I know better to do it with a computer with WINXP and Activesync) , then run the program in the file Treo750_2_27_ROW_EN_DesktopUpdater.zip, and that's it.
If you want to upgrade to other roms like 6.1 normal or lite that you can find in this forum - then you need the other methods (there are two as I know - bootloader method or Kaizer..somthing method). Well, I wrote a guide how to upgrade to WM 6.1 lite using the bootloader method , I just sum up from this forum :
1. Download the rom file and the radio file:
Rom file from here : http://rapidshare.com/files/89355384/Treo750_WM6.1_WWE_Lite.rar
The radio file from here :
http://rapidshare.com/files/89336971/Treo750Radio1.54.07.00.rar
2. Download the Hard-SPL from here :
ftp://xda:[email protected]/Cheetah/Unlocker/CheetahUnlocker.rar
3. Format mini SD card 32 FAT , using a card reader or other way.
4. Do a HARD-SPL with the CheetahUnlocker file ( step 2) . Connect the Treo with your computer using Active sync(for WINXP) and run the file. Use those steps:
- Click the Step 1.... wait the progress bar reach 100%
- Now watch the Screen on your PDA it will launch 2 times verification...
- just click YES ...wait.. and YES again.
- after finisih... wait until the activesync go green again.....
- Now click the Step 2... wait the progress bar reach 100%
- Watch the screen again... same thing.. it will launch 2 times verification.
- click YES ...wait.. and YES again.
- After finish it your PC screen will shows some popup. ignore the reading bla bla bla... about ask u to click ok.
- Just wait untill your activesync go green again.
- Now click that bloody Popup OK button.
- The unlocker app will shows up again..
- Then you will see errors saying.. continue, cancel...etc... bla bla... just click continue.. error message.. iqnore it and then just finish it.
- Now your Cheetah should be on HARD SPL mode.
5. Install the ROM :
a. Using Winrar get the file from step 1. It's name should be : CHEEIMG.nbh
b. Copy the file to the root of the mini SD .
c. Do BOOTLOADER:
1. turn phone on
2. press the MEDIA button AND at the same time with the stylus the RESET PIN
the MEDIA button is the 3rd button on the left side of the phone, under the volume button
the RESET PIN is under the MINI SD card cover
3. keep holding the MEDIA button (left side of phone) until you get the 3 color screen
Wait until it finishes. Then Hard reset the device when prompted. To hard-reset, hold the End key while pressing the pin reset button. Answer “yes” to “Erase all data” prompt.
6. Flash the radio at the same way – just copy the radio file to the mini Sd – it should be the same name. (CHEEIMG.nbh ) .
7. Download the Palm SMS file from hereYou need it only for the lite version)
http://rapidshare.com/files/99335294/threadedsms.rar
or
http://www.megaupload.com/?d=H63TXUP4
And install it as regular software (Copy to the mini SD and run it from the Treo.)
And that it all !!
Do not restore from your backup (You can restore only your data files).
Good luck !!
Update Successful
Thanks mate, I'm not brave enough to try the wm6.1 upgrade yet, but I did manage to upgrade to wm6 with the Updater, even though my device was "not supported". I ended up using the method where you edit the payloads.xml file before clicking 'start' so that it accepts your current device version, etc. I'm all good now.
libal said:
If you want to upgrade to the official palm WM6 rom - then you use Treo750_2_27_ROW_EN_DesktopUpdater.zip and it is very simple - just connect the PPC to your computer . (as I know better to do it with a computer with WINXP and Activesync) , then run the program in the file Treo750_2_27_ROW_EN_DesktopUpdater.zip, and that's it.
If you want to upgrade to other roms like 6.1 normal or lite that you can find in this forum - then you need the other methods (there are two as I know - bootloader method or Kaizer..somthing method). Well, I wrote a guide how to upgrade to WM 6.1 lite using the bootloader method , I just sum up from this forum :
1. Download the rom file and the radio file:
Rom file from here : http://rapidshare.com/files/89355384/Treo750_WM6.1_WWE_Lite.rar
The radio file from here :
http://rapidshare.com/files/89336971/Treo750Radio1.54.07.00.rar
2. Download the Hard-SPL from here :
ftp://xda:[email protected]/Cheetah/Unlocker/CheetahUnlocker.rar
3. Format mini SD card 32 FAT , using a card reader or other way.
4. Do a HARD-SPL with the CheetahUnlocker file ( step 2) . Connect the Treo with your computer using Active sync(for WINXP) and run the file. Use those steps:
- Click the Step 1.... wait the progress bar reach 100%
- Now watch the Screen on your PDA it will launch 2 times verification...
- just click YES ...wait.. and YES again.
- after finisih... wait until the activesync go green again.....
- Now click the Step 2... wait the progress bar reach 100%
- Watch the screen again... same thing.. it will launch 2 times verification.
- click YES ...wait.. and YES again.
- After finish it your PC screen will shows some popup. ignore the reading bla bla bla... about ask u to click ok.
- Just wait untill your activesync go green again.
- Now click that bloody Popup OK button.
- The unlocker app will shows up again..
- Then you will see errors saying.. continue, cancel...etc... bla bla... just click continue.. error message.. iqnore it and then just finish it.
- Now your Cheetah should be on HARD SPL mode.
5. Install the ROM :
a. Using Winrar get the file from step 1. It's name should be : CHEEIMG.nbh
b. Copy the file to the root of the mini SD .
c. Do BOOTLOADER:
1. turn phone on
2. press the MEDIA button AND at the same time with the stylus the RESET PIN
the MEDIA button is the 3rd button on the left side of the phone, under the volume button
the RESET PIN is under the MINI SD card cover
3. keep holding the MEDIA button (left side of phone) until you get the 3 color screen
Wait until it finishes. Then Hard reset the device when prompted. To hard-reset, hold the End key while pressing the pin reset button. Answer “yes” to “Erase all data” prompt.
6. Flash the radio at the same way – just copy the radio file to the mini Sd – it should be the same name. (CHEEIMG.nbh ) .
7. Download the Palm SMS file from hereYou need it only for the lite version)
http://rapidshare.com/files/99335294/threadedsms.rar
or
http://www.megaupload.com/?d=H63TXUP4
And install it as regular software (Copy to the mini SD and run it from the Treo.)
And that it all !!
Do not restore from your backup (You can restore only your data files).
Good luck !!
Click to expand...
Click to collapse
Did everything - step by step but nothing!
still the color screen with the word serial in the bottom!
What is wrong ???
Thanks in advance,
Nir
Got it!!
Turned out vista is displaying fat32 file system no matter what the file system is...
Nir
WM 6.1 Upgrade
Can anyone tell me where the AT&T Upgrade for the Treo 750 is to version 6.1. I have seen many different posts here that show many different links and different downloads with different loading instructions. Is there anything out there that is clear? I am willing to give it a try, but I am not exactly sure of which download to try. Thanks for your help.

Problem on rooting my G1- RC9

I bought it from Germany, and the verison is RC9
I had tried to follow the How to guide from this forum, but i receive the following message after enter to the rainbow screen
1. Serial0
2. 0020288 and Not allowed
I have also try to load in RC7, RC8, and even RC 29, same result. Is it the MicroSD card issue? i am using the one it bundled, formatted it as FAT32..but just by passed that grey screen
I appericated with any comments or suggestion from any of you
Thanks
sorry, i mean i could NOT by passed that grey screen...
please help...
jsonseven said:
sorry, i mean i could NOT by passed that grey screen...
please help...
Click to expand...
Click to collapse
2 things I would check. Make sure the files downloaded properly (check the md5) and double check that the card is formated to Fat32.
my card is formatted as Fat32, and the file Md5 is (2F02DD9A3B7C7F2FE058047B9C7A0245)
does it look ok to you
Thanks for you reply
More info: my G1 is
Firmware = 1.1
Baseband version = 1.22.14.11
Kernel version = 2.6.25-01845-g85d4f0d [email protected] #27
Build number = TMI-RC9 128600
Please help... thanks
jsonseven said:
my card is formatted as Fat32, and the file Md5 is (2F02DD9A3B7C7F2FE058047B9C7A0245)
does it look ok to you
Thanks for you reply
Click to expand...
Click to collapse
looks like your MD5 hash there is the leaked .nhb file used for the UK version to get root.
are you placing the WHOLE .zip on the memory card or just the .nhb file (which I belive it should just be the .nhb file like it is for the US version)
so you got the whole card set to FAT32 which is good
then you placed the .NHB file into the ROOT of the memory card (no folders)
You held down the camera + Power buttons and got into the bootloader
-Did you see the rainbow screen?
-Did you see the grey screen that said "press action key to start update" ( action key is the trackball)
and after it updates .. if it did or does go that far (it will say ok next to each line and completed) the you reboot the phone by pressing the Send + End + menu keys at the same time to reboot the phone from that grey screen.
NOTE: this is for the US version .. I am not really sure if this applies the same for the UK version ...
ALSO I found this for the UK version .. its a little different for the key presses .. not sure if they are right but here they are
1.Copy image file DREAIMG.nbh to the SD card
2.Turn the device power off and insert SD card
3.Hold Camera button, and press Power button to entry Boot loader mode
4.Press Power button to start upgrade procedure (the US version is the trackball as action key .. not sure if it makes a difference)
5.After it finishes, press the trackball and perform a soft reset by pressing "Call" + "Menu" + "End" to reboot. (not sure why you hit the trackball the US version doesnt require that .. just the Send+End+menu to reboot)
THEN the rest that you need to follow after it flashes (if you get that far) is all on this link here
http://android-dls.com/wiki/index.php?title=Rooting_Android
steps are from that site
1.Restart your phone
2.At your phones desktop hit the <enter> key twice and then type "telnetd" and press <enter> again
3.Download an Android Telnet client and connect to localhost. If you are unable to connect, try steps 1 and 2 over again until you can.
4.you now have root!
intersetingly ... this method there is no recovery image or spl to download anywhere in this like there is in the US version ... may just the differences between the two phones BUT if you really wanted to compare or take a look at the US version to decide for yourself then go here:
http://forum.xda-developers.com/showthread.php?t=442480
hope that something in here helps ya
<My answer in blanket>
are you placing the WHOLE .zip on the memory card or just the .nhb file
(I unzip it, and put the .nhb file into the ROOT of SD)
You held down the camera + Power buttons and got into the bootloader
-Did you see the rainbow screen?
(Yes)
-Did you see the grey screen
(Yes, but after "Checking", i received a error message say, "0200230 Not allowed" message)
Hope it help, Thanks brilliant
OOOOOOOH... try this: http://forum.xda-developers.com/showthread.php?t=485364
Thanks for your reply
I had tried that too, but stuck at 4. Select Dream from the list of devices, Click "Get SD Card Serial from WINCE Device"
the program close after i click on the "Get SD ..." button
I tried to do it inside G1, and also card reader..
by the way, my SD card is manufactured by Kingmax
jsonseven said:
Thanks for your reply
I had tried that too, but stuck at 4. Select Dream from the list of devices, Click "Get SD Card Serial from WINCE Device"
the program close after i click on the "Get SD ..." button
I tried to do it inside G1, and also card reader..
by the way, my SD card is manufactured by Kingmax
Click to expand...
Click to collapse
I'd love to help here, but I have no experience with that method. I would try searching that thread to see if anyone else has that same problem. If you can't find anything there, start a new thread here describing your problem in the title (it will attract people who have an idea or know the answer).
How to check my SD card's CID? i just cant run the Qmat...
Okay pardon the bad formatting, I copied this from a site I googled and saved it as a html file. Basically you get your device rooted without Qmat or any WinCE device:
1. insert Transcend 8GB sd card into G1 (sandisk may not work. Lower capacities will work and may even be better. Other makes will also work)
2. download Terminal Emulator from the market and open it on G1
3. type “cat /sys/class/mmc_host/mmc1/mmc1:*/cid” (without the quotes), and keep the code given (something like 1c5356555344202010041c71f0008c5e)
4. Reverse the code byte-wise ( my 1c 53 56 55 53 44 20 20 10 04 1c 71 f0 00 8c 5e became 5e8c00f0711c0410202044535556531c)
5. Overwrite first two digits with 00s: 008c00f0711c0410202044535556531c
6. On your pc browser, go to http://revskills.de/pages/goldcard.html, paste your code and email address and hit continue (while thinking “thank you viperbjk” or donating some money)
7. format sd card to fat32 (may be good to rewrite partition table)
8. download RC7 from http://koushikdutta.blurryfox.com/G1/DREAMIMG-RC7.zip and extract
9. download goldcard from your email address (goldcard.img, less than 440 bytes)
10. copy DREAIMG.nbh to SD card (CASE sensitive! Filename very important)
11. unmount /dev/sdb1
12. type in terminal: “sudo dd if=goldcard.img of=/dev/sdd” (result: 0+1 records in, 0+1 records out, 384 bytes (384 B) copied) (assuming your sd is in /dev/sdd)
13. pull out sd card (now goldcard!) and insert into g1
14. hold camera button and press power button once
15. wait until the bootloader finds the rom and push power button when prompted. (if you do not see this instruction, you have done something wrong)
16. Continue with flashing recovery, HardSPL, RC8 etc...
If you do it exactly according to the steps listed, you should get your device rooted. I know mine worked
EDIT: Bleh, formatting was so bad, I had to fix it. Anyway, once you've done rooting, you should look for ways to change your keyboard layout. The German QWERTZ drove me nuts so I remapped mine to good ol' QWERTY
EDIT2:
How to write the raw sectors without having Cygwin or a Linux device:
- download HxD Hex Editor and install
- open program and go to "extra" and then "open disk"
- choose physical disk and then the removable disk. that is the same as your memory card. I've you don`t know with one it is. just remove the card and restart the program and you will see witch one is disappeared.
- uncheck open as readonly !!!!!!!
- go to "extra" again and the open disk image.
- open the goldcard.img witch you have created from Viper BJK website.
- press ok (512 is fine) en then "select all" and "copy"
- go to the removable disk tab and select offset 00000000 till offset 00000170 go to "edit" and then past write.
- save it
You can't create the HTC GoldCard with your G1 or with a card reader. You need a phone running Windows Mobile (WindowsCE). It's the only thing (that I know of) that can write the goldcard.img to the correct RAW sectors.
torturedsoul802 said:
You can't create the HTC GoldCard with your G1 or with a card reader. You need a phone running Windows Mobile (WindowsCE). It's the only thing (that I know of) that can write the goldcard.img to the correct RAW sectors.
Click to expand...
Click to collapse
You can actually. The process has been documented on the forums but it's in the middle of one of the threads linked earlier. Or you can just follow the guide I posted above. That'll guide you through the entire goldcard creation process.
It works, I did it for my German continental G1. Though there are reports that some Sandisk cards report wrong CID numbers. Mine gave the right one
EDIT: There's a way to write the raw sectors without using Cygwin (for sudo if you don't have a Linux box). If I recall correctly, I used HxD to perform that process. Might be wrong, I'll have to check when I get back home.
Thank you all contributor,, finally i am in RC 7 now.. Thanks soooo much
jsonseven said:
Thank you all contributor,, finally i am in RC 7 now.. Thanks soooo much
Click to expand...
Click to collapse
so after all this help ... you could at least tell us what you did to root it... so others can find the answer if they have your problem
sure, will do it after home, thanks all.

Upgrading Treo 750 to WM 6.1

I am having problems upgrading my Treo 750 from Windows Mobile 6.0 to 6.1 standard. I have run the Cheetah unlocker program. I formatted the card and put the radio program on it. Inserted and ran bootloader mode. The screen turns red, green, white and stays that way permanently. I eventually have to pull the card and reset the device. It comes up and works as usual with wm 6.0.
Is my phone not unlocked?
Is the radio program no good?
Any ideas?
Hard to say, but I suspect you either haven't successfully run the unlocker program, or have not formatted the SD card correctly.
BTW - Upgrading a radio would not get you from 6.0 to 6.1 it would only upgrade the radio, so make sure you have downloaded the proper file.
Understood. I have tried both the radio and the cheeimg.nbh file. Both have the same problem. How long should the upgrade take once the bootloader reads the card (so I know how long to wait until I try something else)?
I figured it out....here is the answer from this website. Thanks
originally Posted by dubLeE
With this method I have successfully unbranded, unlocked, and updated 2 Treo 750s that were originally AT&T/Cingular branded.
I spent hours running through multiple threads reading and searching to finally find a solution that worked flawlessly. These steps have been compiled from multiple threads:
http://forum.xda-developers.com/showthread.php?t=428048
http://forum.xda-developers.com/showthread.php?t=412999
http://forum.xda-developers.com/showthread.php?t=334100
Big thanks to Olipro, konker, and jcrompton!!!
Download the following:
Magic Unlocker from http://forum.xda-developers.com/show...21&postcount=2
CheetahUnlocker from http://forum.xda-developers.com/show...68&postcount=1
1_CHEE_MountExtROM.cab and 2_Chee_Extrom_rename.cab from http://forum.xda-developers.com/show...&postcount=374
Treo750_OS5_2_19199WWE_STD.rar from http://omnifusionhosting.net/treo750/
(I couldn't find the original posts for Treo750_OS5_2_19199WWE_STD.rar so I uploaded to my own site for now)
1. Download, extract, and run MAGIC_UNLOCKER on your phone.
2. Select both options in MAGIC_UNLOCKER and click unlock. This will unlock your phone.
3. Format your SD card to FAT32.
4. Extract Treo750_OS5_2_19199WWE_STD.rar and copy/paste CHEEIMG.nbh to the formatted SD card.
5. Transfer 1_CHEE_MountExtROM.cab and 2_Chee_Extrom_rename.cab to your Treo 750.
5. Run/Install 1_CHEE_MountExtROM.cab and then soft reset the phone.
7. Run/Install 2_Chee_Extrom_rename.cab and then soft reset the phone.
8. Click and run Start>Programs>Chee_Extrom_Unlocker. Run it about 3 or 4 time and you should some type of error messages. Just OK or X them and soft reset the phone again.
9. Open File Explorer and click the drop down arrow, in which you will now see ExtendROM. Open it and delete the 2 files in the partition folder.
10. Download, extract, and run CheetahUnlocker on your computer. For this part make sure you have an ActiveSync (XP) or WMDC (Vista) connection to your phone. Click Flash SPL and go through the steps for CheetahUnlocker to Flash SPL. Don't worry about any of the other items in the menu.
11. After going through the steps in CheetahUnlocker and the phone, the phone will enter into tri-color bootloader screen momentarily followed by Loading screen...
12. Next, you'll see a light blue screen with the heading CHEEIMG.nhb followed by a few other entries below it. At this point, it will tell you press the power button. Go ahead and press the End Call/Power button. This will begin the ROM flashing. The ROM flashing takes about 5 to 15 minutes.
13. When the flashing is completed, the bottom of the screen will say Update successful and the entries above with the OK seen at the end. Now reset the Treo 750 with the stylus and immediately (during the Palm Logo) perform a Hard Reset. This is accomplished by pressing and holding the End Call/Power button and simultaneously resetting the Treo 750.
14. You will now be prompted to Erase All Data. Press the Up key of the D-Pad to continue and erase the data. This will format the phone.
11. Upon completion, the Treo 750 will continue to boot-up and go through the initial start-up steps and wizard. Once completed, your phone will now be unlocked, unbranded, and updated to Windows Mobile 6.1.
I made this thread to help people unbrand, unlock, and update their Treo 750s without having to waste hours looking for solutions and how-to something. Basically, made it easier for the noobies and everyone else to find everything in one thread.
Mine goes to a gray screen immediately with an 'update in progress' bar ... takes about 2 minutes to flash the new ROM.
There doesn't appear to be a forum for the 700W/X. Where do I get information on these earlier Treos?
all ur links are not working please check again

Categories

Resources