my tilt's slider is loose - Tilt, TyTN II, MDA Vario III General

ok my kaiser, tilt, 8925, whatever, whatever, has a loose slider. if i press on the screen you can feel the upper part of the phone move. Their is a noticable gap between the keyboard and the upper part of the phone. My brother has a titl and i compared it. Is their any way to tighten or fix the problem

bump.
I'm comfortable with taking my phone apart and putting it back together.

s0nnyyyy said:
ok my kaiser, tilt, 8925, whatever, whatever, has a loose slider. if i press on the screen you can feel the upper part of the phone move. Their is a noticable gap between the keyboard and the upper part of the phone. My brother has a titl and i compared it. Is their any way to tighten or fix the problem
Click to expand...
Click to collapse
Does the screen feel loose when the device is closed? Or do you mean its loose when its open? Mine was loose when it was closed and almost made a creaking sound when I applied pressure to the bottom right corner, I removed the screws, but was unsure how to disassemble the unit (at the time), so I gave it a good dusting, replaced the screws and It's fine now. What my little dusting solved is still a mystery to me, but it worked.

Related

Broken Standby button

I remembered that I had left my XDA IIi in my friend's car as I was leaving, so I asked him if he could open his car and pass it to me. Before my eyes he makes this huge fumble, like a bar of soap in his hands, and it comes crashing to the concrete floor!! :shock: :x
Apart from a few scuffs and scratches it seemed ok, until I tried to use the standby button. There was no click to it, and it only works now and again if I press it in the right place with enough force.
So I dismantled it to take a further look, and I can clearly see that the micro switch is broken.
Has anyone attempted to unsolder one of these? Looks a little too dodgy to me with the multi-layered board. As I don't use the 'tape recorder' button, I could swap it for that one if it was possible.
Such a shame for such small damage. Any ideas what I should do?
tia

Is your Kaiser wobbly / sloped ?

Been very happy with the Kaiser so far, including on the GPS front ;-) but I'm getting slightly annoyed by two hardware nits :
1. wobbly : in portrait mode when I tap on the screen the right side tends to "hit" the keyboard part underneath and looking closely it's easy to understand why, there is a tiny gap between the two parts, likely for the slide/tilt mechanism
2. sloped : when I pull out the keyboard, the right side of the screen goes out more than the left side so it is slightly sloped. It improved a bit when folding the screen. Again I think this is a constraint of the slide/tilt mechanism
I'm thinking it's a general quirk because I had to change my first model (stuck key) and it had the same problems.
Anyone else noticed that ?
in portrait mode my kaiser seems to be spaced the same all the way around and doesnt push on the keyboard when tapping the screen. I do notice what you mean by the keyboard appearing to be farther out on the right side but after taking a closer look it just seems that way because of the face plate not being uniform all the way down (part where it flares out on the left side). Mine is exactly pushed out on both sides.
Lavachild said:
in portrait mode my kaiser seems to be spaced the same all the way around and doesnt push on the keyboard when tapping the screen. I do notice what you mean by the keyboard appearing to be farther out on the right side but after taking a closer look it just seems that way because of the face plate not being uniform all the way down (part where it flares out on the left side). Mine is exactly pushed out on both sides.
Click to expand...
Click to collapse
Mine's the same as this. It sounds like yours may not be quite right and I'd consider getting a replacement. Of course, if you can live with it, and the functionality is all there then it's entirely up to you.
For the sloping I've had two and they were both the same, so it's probably a design constraint, no biggie.
For the "wobbling", it comes and goes, I can only really feel the "knocks" when I hold the left side tight and tap on the scroll bar on the right, again, no biggie.
solution
iv had the same problem of one end sticking out,
iv gone around it by inserting some tiny smugged paper into the sliding slots at the back, resolves the issue quite well.
I don't seem to have either problem (TyTN II version).

Screen alignment/Slide issues

On my ATT Tilt when ever I close the sliding screen now it does not line up properly. The screen sites a few millimeters to the right of where it should. I called ATT and they said that Slide issues aren't covered under warranty. Anyone else having a similar issue?
No problems here, although keyboard sliding is a bit easier to move since the day I bought it and it sometimes moves when I don't expect it to...
Yeah it def slides easier, but it doesn't line up properly.
I've dropped mine many times (only onto carpets so far, happily) and on occasion have found the top half of the phone slightly misaligned with the rest - resulting in a lip at the top, bottom, or right hand side. I've found that with a little gentle but firm nudge the other way, it usually fits back into place. I think there's a little movement designed into the whole thing, to allow it to take repeated sliding and the odd knock without the stress damaging anything.

[Q] Stylus Problem - PLEASE HELP...

Hi,
When I pull my stylus - nothing happens... doesn't turn on or unlock device.
or during a call opens "notes".
Everything is Checked - it should do it, but it won't...
Any Ideas ???
Thanks
Take out the stylus, then remove the rear panel from your diamond. Look to see if the tiny magnet strip has become dislodged. This happened to mine after I'd had it just two days... it made it difficult to insert the stylus, and it just felt all wrong, because the strip had stuck itself in an awkward position. It also wouldn't recognize when the stylus was withdrawn.
I very nearly returned my diamond under warranty, until I looked closely at the stylus aperture and noticed this issue. I fixed it with a tiny spot of super glue on the magnetic strip and deft use of some plastic tweezers... saved days of re-programming a replacement.
Mr. Orange owes me a beer I reckon ;-)
Thanks for the reply...
The magnetic strip is there... I feel the magnet working...
but the diamond doesn't recognize when its in or out...
Anyone ?? Help - is it hardware or software ????
also a problem with the magnet strip
I own my diamond now for three weeks and something went wrong with the magnetstrip..it looks like it is still inplace but the magnetic force is stronger on the outside of the phone then on the inside (where its supposed to be) I'm trying to move te strip in the right position. but is not working.(seems like te strip is in the correct position)
It just happened. Really annoying..The phone goes on when I remove the stylus. (and the stylus is holding , but I don't get "the magnetic snap anymore"
Itay Shekel said:
Hi,
When I pull my stylus - nothing happens... doesn't turn on or unlock device.
or during a call opens "notes".
Everything is Checked - it should do it, but it won't...
Any Ideas ???
Thanks
Click to expand...
Click to collapse
shalom! go to:
settings/personal/phone/advanced (tab)/"when a call is connecting, open the Notes application when stylus is pulled out"
also in the diamond's manual

ZUK Z1 - Hardware button light intensity

Hey all
After reading this forum for ages I took the plunge on a Z1, and am not disappointed!
I had one question, if anyone is able to help.
The hardware buttons light up with a nice white LED.
However, the one on the left (select open apps) is much, much brighter than the one on the right (back).
In fact, it's almost as if the right hand one doesn't work at all.
Is this the same as everyone else's phone, or does mine have a defect?
Many thanks to anyone that can compare theirs.
Uri
P.S: I have the grey one with the black front, which may make this more noticeable.
Uri
someoneelse999 said:
Hey all
After reading this forum for ages I took the plunge on a Z1, and am not disappointed!
I had one question, if anyone is able to help.
The hardware buttons light up with a nice white LED.
However, the one on the left (select open apps) is much, much brighter than the one on the right (back).
In fact, it's almost as if the right hand one doesn't work at all.
Is this the same as everyone else's phone, or does mine have a defect?
Many thanks to anyone that can compare theirs.
Uri
Click to expand...
Click to collapse
Is a hardware issue, I think.
My 2 buttons has the same light intensity and is a good intensity.
In my previous prone, a OnePlus One, I have suffered this issue: the back button had a lower light intensity compared to the other buttons.
bartito said:
Is a hardware issue, I think.
My 2 buttons has the same light intensity and is a good intensity.
In my previous prone, a OnePlus One, I have suffered this issue: the back button had a lower light intensity compared to the other buttons.
Click to expand...
Click to collapse
Thanks very much for the quick reply
To be honest, everything else about the phone is perfect (screen, fingerprint scanner, buttons don't wobble, etc), so for the first time in my life I might just live with "almost-perfect".
I had too many issues with iPhones and am worried if I swap it out, then the replacement will have some other defect like screen bleed, etc, etc.
Uri
someoneelse999 said:
Thanks very much for the quick reply
To be honest, everything else about the phone is perfect (screen, fingerprint scanner, buttons don't wobble, etc), so for the first time in my life I might just live with "almost-perfect".
I had too many issues with iPhones and am worried if I swap it out, then the replacement will have some other defect like screen bleed, etc, etc.
Uri
Click to expand...
Click to collapse
If you can live with this issue: Don't return it!
I also haven't returned my OPO. Is a small detect I think
Easy to fix
I had this issue too, but it is easy to fix. When you open your phone backcover, you only have to remove the speaker and reposition the led. The led is loose in a cable and so you can reposition it until the buttons have the same intensity and fix it with some glue.
On my phone the intensity is now exactly the same and i only needed half an hour for it.
When you remove the backcover warm it up a bit and use a sucker to avoid scratches in the frame.
Well I can confirm that I have the same issue on my white Zuk! But it's not very noticeable so i'm keeping it like it is!
microdoof said:
I had this issue too, but it is easy to fix. When you open your phone backcover, you only have to remove the speaker and reposition the led. The led is loose in a cable and so you can reposition it until the buttons have the same intensity and fix it with some glue.
On my phone the intensity is now exactly the same and i only needed half an hour for it.
When you remove the backcover warm it up a bit and use a sucker to avoid scratches in the frame.
Click to expand...
Click to collapse
Don't seems too easy to remove the Zuk Z1 backcover if you don't are McGiver
bartito said:
Don't seems too easy to remove the Zuk Z1 backcover if you don't are McGiver
Click to expand...
Click to collapse
Wasn't very hard to remove, i didn't brake any clips. Use a sucker and as soon as you see a little gap, use a plastic pick or your fingernails to gently pull up the backcover.
After i opened it i removed the tape from the phone and the backcover. After the work is done you can simply close the Backcover without tape or something. I didn't use tape and had no gaps afterwards.
microdoof said:
Wasn't very hard to remove, i didn't brake any clips. Use a sucker and as soon as you see a little gap, use a plastic pick or your fingernails to gently pull up the backcover.
After i opened it i removed the tape from the phone and the backcover. After the work is done you can simply close the Backcover without tape or something. I didn't use tape and had no gaps afterwards.
Click to expand...
Click to collapse
I just tried that; broke some pins immediately, they seem to be of very soft plastic... So i would recommend others not to do it
othe01 said:
I just tried that; broke some pins immediately, they seem to be of very soft plastic... So i would recommend others not to do it
Click to expand...
Click to collapse
I supposed...
microdoof said:
Wasn't very hard to remove, i didn't brake any clips. Use a sucker and as soon as you see a little gap, use a plastic pick or your fingernails to gently pull up the backcover.
After i opened it i removed the tape from the phone and the backcover. After the work is done you can simply close the Backcover without tape or something. I didn't use tape and had no gaps afterwards.
Click to expand...
Click to collapse
Hi guys, even I have noticed the same, the back button light is dimmer than task button. Can somebody suggest if I should get it replaced?
aniketsabarad said:
Hi guys, even I have noticed the same, the back button light is dimmer than task button. Can somebody suggest if I should get it replaced?
Click to expand...
Click to collapse
Same for me. back button light intensity is very low compared to menu button. Its not a big issue. My friend also having same issue. you may get same problem in that replacement unit also. So,better keep as it is.
@arunpkrt and @aniketsabarad If you don't mind there is also an option inside the Zuk Z1 lights configuration to switch off this little ugly menu LED and back LED. The function itself stays active and the touch area is large enough to hit the sensitive zone blinded easily .
arunpkrt said:
Same for me. back button light intensity is very low compared to menu button. Its not a big issue. My friend also having same issue. you may get same problem in that replacement unit also. So,better keep as it is.
Click to expand...
Click to collapse
You guys are right. I faced this problem initially. The phone was perfect, I set it up nicely and was using it. But after a day or two this back button led issue started frustrating me. I applied for a replacement and was surprised to see that even the replacement unit had same issue. So really no point getting it replaced. If it really bothers, you can take the risk to open up the back case as other members suggested.
I also have the same issue but its not important because im using onscreen keyboard.
Overall is perfect but one thing is missing. We still dont have marshmallow to enjoy before Android N release.
Edit: Happy 500th post to me! God Bless!
I don't have the issue, but if ever I had it, it won't matter as I disabled the hardware buttons once I started using mine. 5.5" is too much of a screen and the 3 on screen buttons don't take up that much space. I am much worried about pressing the hard home button because I read from some users that it failed after 2 or three months of using the phone. I only use it for finger print. No need to press it. Double tap to wake, double tap to sleep. No hard buttons to wear.
bluestricker_21 said:
I also have the same issue but its not important because im using onscreen keyboard.
Overall is perfect but one thing is missing. We still dont have marshmallow to enjoy before Android N release.
Edit: Happy 500th post to me! God Bless!
Click to expand...
Click to collapse
Mine has the same problem, if I where you I would just keep it that way and don't go to all the trouble to send it back.
You can also Disable the lights thats what I did

Categories

Resources