Database Develop

Broken Standby button

I remembered that I had left my XDA IIi in my friend's car as I was leaving, so I asked him if he could open his car and pass it to me. Before my eyes he makes this huge fumble, like a bar of soap in his hands, and it comes crashing to the concrete floor!! :shock: :x
Apart from a few scuffs and scratches it seemed ok, until I tried to use the standby button. There was no click to it, and it only works now and again if I press it in the right place with enough force.
So I dismantled it to take a further look, and I can clearly see that the micro switch is broken.
Has anyone attempted to unsolder one of these? Looks a little too dodgy to me with the multi-layered board. As I don't use the 'tape recorder' button, I could swap it for that one if it was possible.
Such a shame for such small damage. Any ideas what I should do?
tia

Black screen?

Hello!
I have opened my BA case, cause the down button on the front panel stopt working as it should (I had to press it REALLY hard to make it work). The rubber part was a bit used.
After reassembling the unit, the screen is dead - it remains black (backlight is on, touchscreen works, but the image is black). What could go wrong?:/

did u figure it out??
check that nothing is torn or broken, espcially those thin soft connectors...

Yep, its functional again. Simply the maiunboard connector did get 'used off' - had to correct the pins (just... move them a little) with a thin needle

_TB_TB_ said:
Hello!
I have opened my BA case, cause the down button on the front panel stopt working as it should (I had to press it REALLY hard to make it work).
Click to expand...
Click to collapse
I've had that twice now, fortunately Orange Care brought me a new one today.

Stylus Sensor Location?

Does anyone know where the stylus sensor is located? I am having trouble with it, and the stylus is not moving in and out like it used to. I pushed what looked like a magnet back into the side of the stylus port, and now the stylus moves freely again, but now the sensor doesn't work at all. In Gyrator, it just shows STYLUS, not IN or OUT like it used to.
Thanks

Switch...
It's not a sensor, it's a micro-switch located about a third of the way up the stylus slot. It's operated by a small plastic 'notch' which releases the switch when you draw the stylus out. It sounds like the plastic notch is either broken or missing altogether. Take the back cover off, remove the stylus and look in the stylus slot level with the first 'n' in 4GB Internal Storage. I don't know what you can do about it if it is indeed broken?

Thanks.
I had it working again after messing with it with a paper clip, but it didn't last long. Guess ill wait for something else to break, and bring it to Sprint for repair. Funny thing is, the phone is less than a week old.

screen problem, most of the time do not work

Hi, i think i have problem with my screen, it's not work anymore, so I decided to reflash device with official Rom. But it didn't work.
Moreover before windows system start for the first time ir requires to tap on screen to boot. So now I cannot use my TytnII at all.
Is it any options to boot it without tapping on screen?
Or just to flash with other ROM, but HARdspl is not installed so a bit afraid to brick my phone. please help

hurdleman said:
Hi, i think i have problem with my screen, it's not work anymore, so I decided to reflash device with official Rom. But it didn't work.
Moreover before windows system start for the first time ir requires to tap on screen to boot. So now I cannot use my TytnII at all.
Is it any options to boot it without tapping on screen?
Or just to flash with other ROM, but HARdspl is not installed so a bit afraid to brick my phone. please help
Click to expand...
Click to collapse
install hardspl (same procedure as flashing) and then install rom of your choise if it dosn't work have you done any of the following
dropped it in water
gone in the washing machine
etc.... stuff like that

why don't you get a new digitizer??? it's $10 for kaiser?? i've been changing them like underwear...every half a year.
what is it, what's asking you to click on screen? if it's just a welcome screen, put welcome.not file in root.

papo said:
why don't you get a new digitizer??? it's $10 for kaiser?? i've been changing them like underwear...every half a year.
what is it, what's asking you to click on screen? if it's just a welcome screen, put welcome.not file in root.
Click to expand...
Click to collapse
hehehe funny expression 'changing them like [email protected]
what do you only change your underwear 2 a year

hehe, i live in Lithuania, so price with shipping will be around 25$. I think this isn't very cheap. Finally got screen working, but after 30min of using again no respond to tapping, then again working fine, and after that again no. it's annoying. I think it's problem with digitizer? I haven't it dropped to water, it almost brand new

hurdleman said:
hehe, i live in Lithuania, so price with shipping will be around 25$. I think this isn't very cheap. Finally got screen working, but after 30min of using again no respond to tapping, then again working fine, and after that again no. it's annoying. I think it's problem with digitizer? I haven't it dropped to water, it almost brand new
Click to expand...
Click to collapse
thats good you got it working
hope the problem doesn't happen again

if we assume the problem is harware, it would most likely by at one of two spots.
place, where the ribbon cable is soldered to lcd
or place where two piecies of digitiizer are connnected to each other.
might help if you check on the ribbon and glue a plastic tape all around the edge of digitizer, making it press little bit more on it
well, if that's hw probllem. but first you shoud try different rom. you can reflash without digitizer working. and check for pocket controller or similar if you want you can control pda from pc with it. there are two free and Pocket contr is trial.

if you just want to bypass the "tap here to use your device" message on the first boot up, search for "welcome.not".
create a blank file named "welcome.not" and place it in the root of your sd card and then power on the device for first boot up.
make sure it is a blank file. make sure it is named EXACTLY "welcome.not". if you are doing this with your windows pc, make sure you have turned off "hide file extensions of known file types". otherwise, the file might actually be named "welcome.not.txt" but might show as "welcome.not" on your pc.
search about it for more information.

hi, have tried differnt rom, but problem still persist. screen is not working, but sometimes it starts working very well. but most of the time it not respond. when backlight goes out and touch screen it starts to light but can't touch any options on. So what can be the problem, only digitezer or whole screen?

it was more probable it would be hw. but we need to eliminate all possibilities and reflash was easiest.
Still there is more things which could be the problem.
And there is no way to tell for sure what is it.
Did you say the pda is new? or digitizer?
And then you said when backlight goes off, digitizer will stop working, but still reacting on touch (to light the backlight) Is this right?
When will it stop / start working? Does it change if you press on body - case?
Does it change if you slide keyboard out or in?
There would be a short test each time pda/screen is powered, if digitizer fails in this test, it would be ignored till next test pass. Could this be your case?
digitizer could be broken on corner, or has bad contact inside
- You can test it, if you'll solder test wires on it and measure resistance, which should be around 500 ohms without touch and going down on each touch, can't go higher! test for both H & V
but the same reaction could be if ribbon cable connecting two parts of kaiser is broken (or connector on mobo side)
but if it's new it shouldn't.
and at last there could be problem on mobo. inside the controller chip or on it's connection, soldering. But not very probable.
It definitely looks like bad connection somewhere. You need to find out where, so you'll not buy digitizer if it's good or ribbon cable.
Put plastic tape around digitizer inside, as I wrote before, inspect ribbon cable and digitizer and it's connections. Try to locate event when it goes wrong.
If you'll not open it and check on these things, then maybe get a new part which will show bad, then I don't see how more we could help you.
You can use it without touch screen somehow or get a new phone.
Digitizer is US$8 with shipping to Lithuania. That's really cheap, even for us from central european countries.
http://cgi.ebay.com.au/HTC-P4450-Ka...m&pt=PDA_Accessories&hash=item5192adf317#shId
and ribbon cable have fair price too,
http://cgi.ebay.com.au/Flex-Cable-R...ewItem&pt=PDA_Accessories&hash=item3cadad06a3

papo very informative
All i want to add is that it's easier to replace the whole screen with a digitizer already on as the digitizer is very hard to remove since glued to the glass more than likely will get wrecked and not able to replace new, whereas full kit wont cost a lot more and will be less stress just 4 screws on the back plate of Tilt "where sim door is".

Well, it is not new, i've bought it from one girl, but it's like brand new, no scratching at all, very good condition.
also, yesterday i checked all the connection inside it, but the problem persisted.
I think I have understood what kind off problem it is...when remove sim card it stars to work perfectly. When insert sim, it work some time very well. Then again screen start not to respond, any ideas?

hurdleman said:
Well, it is not new, i've bought it from one girl, but it's like brand new, no scratching at all, very good condition.
also, yesterday i checked all the connection inside it, but the problem persisted.
I think I have understood what kind off problem it is...when remove sim card it stars to work perfectly. When insert sim, it work some time very well. Then again screen start not to respond, any ideas?
Click to expand...
Click to collapse
mm, I know some pretty good spells, but you need a magic wand to make them work. If you don't have any you need to:
tape the screen as I wrote before (half millimeter tape),
if no help, hardwire analog multimeter on digitizer and test it properly (while pda off and open) as I wrote before
tape bended paper across connector on mobo.
OR just get a new digitizer straight away. it's $8 and pretty good chance that it's the issue. it's maybe 50% chance but what I mean is:
You have $200 phone (now on market) let's assign it 200 points
It's working on 20% with digitizer broken, now you have 40 points
digitizer 8 points to add. With 50% chance to fix = 16 points to add
result: by adding 16 points you gain 160 (200 - 40) that's 10x gain = good risk

WTF with my screen? post photos. on the first my screen, on the second lcd screens which are beiing sold on ebay.
I decided to buy new digitizer, but when looked at my screen, it realized have completely different layout where digitizer is connecting to screen. Am i right? Is the digitizers which are sold on ebay will suit my screen?

that's fine. they all work. They are not oem but works well. Maybe not so scratch resistive.
You may get the digitizer solo, but they will not include a special double side tape which goes around and is holding it together. You can make that tape, but it's pain as stylez said. A lot of cleaning the used old one, then cutting small strips of ds-tape. and you need to put a paper or something in between two layers of tape as you need a little space in between. And then soldering that ribbon. Better just get whole assembly.
==
I see you tried that tape, before you buy it, try the last thing. The place where digitizer is soldered to lcd modul.
On that piece you sent photo of, you need to open back cover.
check the picture:
1. peel off antistatic tape from connector, from up -> down
2. take cover off
3. there will be attachment of digitizer behind the cover, like on your second picture.
Check for good connection
AND
check if soldered pins could not be touching the back cover you took off
( i had this problem once)
put electric tape accross it a give it a try - that will isolate it from back cover & make a little pressure if bad connection
=

[Q] Problem with display / S-pen??

Hi guys
I am not sure if this has been posted before, i did a quick search but nothing shows up.
Sometimes If I hold the pen close enough (but without touching) the screen would annoyingly picks it up. The problem is way more apparent if I hold the phone upside down, with the screen facing downwards and holding the pen inclined at an angle. Is this a common problem?

I have a video link but unfortunately I cant post the link here it wouldn't let me. Go to youtube and search "Galaxy note s-pen problem" the one by dudelmt

GALAXYNOTE said:
Hi guys
I am not sure if this has been posted before, i did a quick search but nothing shows up.
Sometimes If I hold the pen close enough (but without touching) the screen would annoyingly picks it up. The problem is way more apparent if I hold the phone upside down, with the screen facing downwards and holding the pen inclined at an angle. Is this a common problem?
Click to expand...
Click to collapse
Wacom styluses are magnetic based, not capacitive, so technically it doesn't need to touch the screen. You can place a piece of paper over it and trace images for example.
I can't reproduce what you are seeing though. If I open s-memo, and place the stylus in contact with the screen with no pressure, it doesn't trace.
Just watched the video - holy cow, your pen is nowhere close to the note. wow. it looks like it's a good 1.5 cm or so.
- Frank

For the lazy.
http://www.youtube.com/watch?v=9VfkXo0KU5c&sns=em

Can not reproduce this on my device. Sounds like some electronic magnet issues or perhaps some other pen?? Anyways, sounds like you should get your device replaced unless you wish to keep it as a Magical Note ;-)
No really can not reproduce your issue on my note.

Do you use your phone upside down often?
(really tired and sarcastic, I know it occurs right side up too )

Faulty Pen
You have a faulty pen! Your pressure sensor from pen's tip is defective, jammed, or maybe only the white tip is physically stuck.
Everybody could reproduce this behavior by putting the pen close to screen, with memo app running, and applying pressure on pen's tip with your finger/nail.

So it's normal for the S-pen not to register if there is no pressure applied despite contact? Because that is what is happening with my s-pen. There is contact, no pressure, and it does not register. Is this how it is suppose to work?
Also, does the S-pen have a very faint click or sound when applying pressure like it is activating a pressure sensitive "something".
Thanks

Same problem here.
My Video:
http://www.youtube.com/watch?v=tgFLb8bTnXY
I contacted Samsung for replace the Pen, but they told me that is the first time they receive this type of problem.. so.. they will tell me something after some check..

Same problem for me, noticed that it's usually after the first time you touch the screen with the pen, like it still thinks the pen is touching even though its not. I'll log it with Samsung too see if they give me the same 'haven't seen this before' line.

I also have the same issue, it's rather annoying.
Will play around and see what I can find out.

Did Someone find a replace for the S-Pen?

Same problem here, appears to be worse when you first start using the pen. They should add a calibration option for the pressure to fix this, i think its now auto calibrating and that's why the problem looks worse at start.

FIXED- S Pen Problems...
Hi guys,
I had the same problem of the S Pen drawing while hovering about 15mm above the screen, I managed to fix it but it ain't easy....
It involves pulling the pen apart and there are tiny parts in there!
I am kicking myself I did not take photos, but I honestly didn't think I would get it to work again...
If anyone is still having probs, I can make up a tutorial of what you need to do.
Atleast you MAY not have to buy another S Pen.
Cheers,
Dan.

heelerdog said:
Hi guys,
I had the same problem of the S Pen drawing while hovering about 15mm above the screen, I managed to fix it but it ain't easy....
It involves pulling the pen apart and there are tiny parts in there!
I am kicking myself I did not take photos, but I honestly didn't think I would get it to work again...
If anyone is still having probs, I can make up a tutorial of what you need to do.
Atleast you MAY not have to buy another S Pen.
Cheers,
Dan.
Click to expand...
Click to collapse
waiting for a tutorial

S-Pen repair tutorial- not for the faint-heated
OK...
Now I believe everyone that is having problems has at one time or another accidently or on purpose pulled the rear end out.
From what I have seen you CANNOT replicate this fault without that happenning.
Using a small blade prise the button from the Spen starting at the rear end.
The button will flex and pop out.
Pull the rear end off the pen (again ) now CAREFULLY and into a small tray if possible, turn the pen upside down and the 'bits' will come out, they are:
white nib
tiny O ring
tiny disk with nob one end and hole the other
electronics with button
What had happened on mine is that the o ring, disk and nib had pulled apart so that the disk and the wire-wound rod were always in contact so the Note always thought that the pen was in contact with the screen.
The correct order of bits is:
Nib-Disk-O Ring- Rest of electronics...
you will see the nib has a nob that will locate into the disk, the other side of the disk will hold the oring and all this sits against the wire-wound rod.
NO I AM NOT PULLING MINE APART AGAIN FOR PICS!!!
I put the electronics back in first and then using tweezers put the other bits back in through the button hole before carefully sliding it all back to the nib-end of the pen.
The button then pushes back in and locks.
Now, I a happy to answer questions, or if you like, and if you trust me, I am happy to have you send your pen to me here in Australia and I will repair it if i can.
Mine has been 100% since I did this...
Hope this helps!
Dan.

This sounds like an individual problem. For if the Note was faulty as described then it would have been noticed by the 80% in the poll here who like me think the note is pretty perfect.

Individuals and S Pen failures
I agree Gaugerer, it seems though that more and more individuals are finding this problem as more and more notes are sold...
Atleast it is fixable without the exhorbitant price asked for for a replacement stylus.
Cheers, Dan.

Hi I am thinking of also getting a Note and thus I went to a store for trying it out since I want to use it esp. also for taling notes during my meetings.
Thus the S-Pen is one of my keys in the decision and it did disappoint me:
I tried writing some text in the S-note app and when ever I finished a word and raised the pen the line is still drawn further and thus the text was not quite readable.
Same happens when I use the handwriting field at the bottom (instead of the screen keyboard). Then due to the lines being drawn further when the pen does not touch the screen, the recognition puts together the words.
So I think the problem is facing on many devices.
Does anyone ever get a better / more in-details answer from Samsung? Or should we one by one contact their support?

frankiboy_01 said:
Hi I am thinking of also getting a Note and thus I went to a store for trying it out since I want to use it esp. also for taling notes during my meetings.
IThus the S-Pen is one of my keys in the decision and it did disappoint me:
I tried writing some text in the S-note app and when ever I finished a word and raised the pen the line is still drawn further and thus the text was not quite readable.
Same happens when I use the handwriting field at the bottom (instead of the screen keyboard). Then due to the lines being drawn further when the pen does not touch the screen, the recognition puts together the words.
So I think the problem is facing on many devices.
Does anyone ever get a better / more in-details answer from Samsung? Or should we one by one contact their support?
Click to expand...
Click to collapse
I contacted "Samsung Exclusive Italy" but they simply told me that check for this problem and recall me. I Never received a call from them.
Thanks to heelerdog for the tutorial, but i dont understand well english, and without some pics I'm afraid to break the S-pen