Lanyard Hole Problem - Tilt, TyTN II, MDA Vario III General

Yes, this a serious post. Does anyone have any tips for getting anything attached using the lanyard holes of the Kaiser? I have tried string, thin twine, key rings, lobster type clips and I can't get anything to hook underneath the lanyard holes. It is getting really frustrating. I know someone must have some tips. Thanks.

i used a paper clip to fish out a wii remote strap

outphase said:
i used a paper clip to fish out a wii remote strap
Click to expand...
Click to collapse
A paperclip is a good idea, thanks. I guess I could keep bending it with pliers to make it fit...

If you must use something metal, get some nylon-coated beading wire and some crimps, and make your own.
Mare

outphase said:
i used a paper clip to fish out a wii remote strap
Click to expand...
Click to collapse
thats what i did with mine too lol i had a psp strap on it for a wile too.

I used a twist tie to push the string through, then tied the string to a heavy wrist strap and pulled in back through with the string.....
I like the end result, I wouldn't have put anything there for my tilt, until i saw the thickness on the string for the wrist strap, it just barely fits through the holes... So i feel fairly confident in it..... still gonna keep it in a belt holdster though

I put the string through as far as it will go, the use a safety pin/stick pin tip to kind of drag it though the rest of the way.

I used a needle threader, of course I took it off right away. Wearing the tilt could be a pain in the neck with the weight. But I just had to try it.

See, I'm weak in the force so my abilites are perfect for pulling the small string out.

trial and error, took me about 30 mins to get my tiny MicroSC reader keychain thing attached to it! Perseverance, and also dipping it in hot wax helped keep it in a "C" shape to allow it to curve round hope that helps

GilesTheAlmighty said:
trial and error, took me about 30 mins to get my tiny MicroSC reader keychain thing attached to it! Perseverance, and also dipping it in hot wax helped keep it in a "C" shape to allow it to curve round hope that helps
Click to expand...
Click to collapse
Very crafty... Typically if I'm doing anything involving hot wax it relates more to nymphomania or pyromania...

I kow this is an old thread but I went looking for an answer..
I was trying to install a lanyard on a USB-C adapter but the tiny hole and normal lanyard thread for this type of device had me stimied. After fooling around for 30 minutes I stripped off a 2" strand of twisted copper from some 16 guage wire, folded it over the lanyard thread at the wire mindpoint, used needle nose pliers to pull both ends of the wire through and the lanyard thread came with it. Ended up doing 4 units in about 5 minutes. Hardest part was getting the copper wire separated from the lanyard thread. (Not that hard).

Related

Magnetic Mini(malist) Mount

Do I get the award for the simplest mount?
Basically what I've done here is take the self-adhesive metal plate tomtom supply for securing their gps 'mice' to the car. It holds my Advantage just beautifully. I thought it might swing around a bit on its axis because the plate is so small but if you sit the end of the advantage that has two magnets (either side of the keyboard connector) it seems to hold in place pretty rigidly. I've tried a few twists and turns as well as emergency stops and not lost it yet. It might be the case that the screen would flop off the keyboard at a very rapid deceleration but it hasn't happened yet. I leave the cover on for convenience and to cushion its fall if that does happen.
So far it seems pretty secure but use at your own risk.
Cost approx GBP£5 (USD$10) plus tax, postage etc and ultimate convenience. No sucker bases, swing arms etc and it sits right where its needed for power etc.
I had mine left over from a previous tomtom installation but similar plates are apparently still available as spares e.g. from here.
I'm not sure mine is magnetic, by the way, it may just be metal.
The same I thought...but I sold TomTom gps years ago...
inframan said:
Do I get the award for the simplest mount?
Basically what I've done here is take the self-adhesive metal plate tomtom supply for securing their gps 'mice' to the car. It holds my Advantage just beautifully. I thought it might swing around a bit on its axis because the plate is so small but if you sit the end of the advantage that has two magnets (either side of the keyboard connector) it seems to hold in place pretty rigidly. I've tried a few twists and turns as well as emergency stops and not lost it yet. It might be the case that the screen would flop off the keyboard at a very rapid deceleration but it hasn't happened yet. I leave the cover on for convenience and to cushion its fall if that does happen.
So far it seems pretty secure but use at your own risk.
Cost approx GBP£5 (USD$10) plus tax, postage etc and ultimate convenience. No sucker bases, swing arms etc and it sits right where its needed for power etc.
I had mine left over from a previous tomtom installation but similar plates are apparently still available as spares e.g. from here.
I'm not sure mine is magnetic, by the way, it may just be metal.
Click to expand...
Click to collapse
Great idea. So in theory, any magnetic adhesive strip should serve in the car. Hmmm....
Maybe these
http://cgi.ebay.co.uk/Magnetic-Stri...yZ123866QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
Or cheaper ones!
inframan said:
Do I get the award for the simplest mount?
Basically what I've done here is take the self-adhesive metal plate tomtom supply for securing their gps 'mice' to the car. It holds my Advantage just beautifully. I thought it might swing around a bit on its axis because the plate is so small but if you sit the end of the advantage that has two magnets (either side of the keyboard connector) it seems to hold in place pretty rigidly. I've tried a few twists and turns as well as emergency stops and not lost it yet. It might be the case that the screen would flop off the keyboard at a very rapid deceleration but it hasn't happened yet. I leave the cover on for convenience and to cushion its fall if that does happen.
So far it seems pretty secure but use at your own risk.
Cost approx GBP£5 (USD$10) plus tax, postage etc and ultimate convenience. No sucker bases, swing arms etc and it sits right where its needed for power etc.
I had mine left over from a previous tomtom installation but similar plates are apparently still available as spares e.g. from here.
I'm not sure mine is magnetic, by the way, it may just be metal.
Click to expand...
Click to collapse
This is great! Can't believe I didn't think of it. DUH! Great job on reporting this.
I'm thinking of going to the hardware store and getting a small L shaped metal "plate" and put velcro on the back of it. Should hold things nicely.
Like the way you kept the case on it. I would have done exactly the same thing. Not only does it help but I would be too lazy to remove it all the time when I got into my vehicle.
magnetic adhesive strip
Actually I tried magnetic adhesive strip, but it is quite weak ... Found out a normal metal ruler is better magnetic adhesive, as the keyboard is quite a strong magnet
@topic
Its really a good idea... I might try it...
Im using this one
it's fantastic and very solid

I made my own self-contained kickstand for Leo. Here is how...

I decided to make my own kickstand for my HD2 and am pleased with the result. The benefit of how I did it is you don't need to carry any seperate accessory as the stand is built into the case so you will always have it with you as long as you have your phone. Nothing else to lose.
To make one you will need a stiff snug fitting case, cutting knife, pen and cutting board. These cases are inexpensive so if you make a mistake its not the end of the world.
Just cut 3 slots into the case. Make sure you draw straight lines inside the case and that the flap is centered. Don't make the flap too narrow as you want some strength. You can make it as wide as you like. You may want to make a template (on card) of the rectangle flap first and then draw around it inside the case. Make sure the flap is not too long or too short. The bottom of the flap should be reasonably close to the edge of the case too.
To open the flap, just flex the plastic by firmly pulling it with your thumb towards the center, or use your fingernail to catch the edge. To close it just click it it back to its original position and it stays in nice and flush. It will not accidently pop open. The flap is virtually invisible when closed.
It works brilliantly. I am well chuffed!
LoL very nice never thought about that... I have the same case, and it kinda might be useful ! nice tip cheers
Wouldn't the flap start to wear after a while and the opening degrade over time?
I don't think it would wear over time. I did not score or crease the hinge so it will never snap off. It is just flexed. The case is a flexible material. Nothing to degrade.
I mean like clipping of the rubbery material and the flap starts to stay open. Over time.
It shouldn't stay open as the way it's been cut and because of the thickness it CLICKS into place. Wedged in. It's a little tricky to open so I can't see it springing open by itself. Time will tell but think it should be fine.
tboy2000 said:
It shouldn't stay open as the way it's been cut and because of the thickness it CLICKS into place. Wedged in. It's a little tricky to open so I can't see it springing open by itself. Time will tell but think it should be fine.
Click to expand...
Click to collapse
I think the concern is that with any press-fit or clip-fit flap, the friction will wear out the material slowly and with time become lose.
Even the HD2 OEM battery door, if opened/closed enough time, will become closed
The question becomes, then, whether the flap will outlast the device
The other idea to make the flap last longer is the ANGLE the cut so that instead of cutting perpendicular to the surface of the case, you cut slanting away from the way the flap open. This way you create a little lip for the flap to lock into.
felixdd said:
The other idea to make the flap last longer is the ANGLE the cut so that instead of cutting perpendicular to the surface of the case, you cut slanting away from the way the flap open. This way you create a little lip for the flap to lock into.
Click to expand...
Click to collapse
I thought of that and it was going to be my second attempt if this first attempt did not work out but I was surprised to find it click into place even with a non angled cut.
I also thought about adding a small bit of tape to the inside lip of the flap so you could pull it open, but dismissed it for looking unsightly.
Also thought about a magnetic closure. So far so good as is. As I say time will tell but I have been opening and closing it a lot so far and still no problems.
is that an ebay case? link to seller
ya if i do this i'm definitely going to angle cut it.
methodz this is the one I bought. Super cheap:
http://www.netimes.com/shop/resin-soft-jelly-case-for-htc-hd2-t8585-htc-leo-p-2455.html?cPath=80_731
I gotta say, I've seen a lot of DYI stuff on here (charging dock through a box, lanyard through battery cover, piggyback extended battery, etc), but this is one of the most ingenious thing I've seen. Kudos to you!!
..and for those who are questioning the durability of this, don't get the ultra thin gel case. Get one with a good amount of thickness so it doesn't flex too easily. Don't worry if it doesn't fit snuggly back on the case when you done...because it will if you get a good gel case. (I've done cutting to a few of my cases on other phones..no case for HD2 yet)
Very nice indeed!
I'm going do the same with mine.
Nice one mate. I too have the same type of case and would never have thought of this! I can see why people are talking about it losing its strength over time, and I too imagine that it would eventually lose the will to actually stand the device up, or click back into place - one or the other - but I would only use this "feature" maybe once or twice a week, so it would take a long time to have any detrimental effect on the case. But let's face it.... it's dirt cheap and replaceable!
Very clever idea mate - thanks a lot
I think it would be great if some case manufacturer took this idea up and made a professional version. I should get royalties of course.
I have noticed after prolongued time in the open stand up position, it does slightly spring open after closing it - however storing it on its back for a short time DOES make it stay flush again so no big issue.
I may try an angled cut next time. Think I will order a couple more cases and experiment on the most optimal design.
Wouldn't it be funny if you cut it the opposite way the accelerometer turns? Ha.
This is an AWESOME idea. $4.00 for a case? Fix def worth the "degraded" possibility.
Yes make sure you cut the flap in the right direction to your landscape view. Very important!
Sure you've seen this anyway but pocketnow.com wrote this up, kudos:
http://pocketnow.com/how-to/make-your-own-htc-hd2-kickstand
It made wmpoweruser.com news too!
http://wmpoweruser.com/?p=14723
Oh and if anyone else wants to try it I found it on ebay too for 4.00 GBP
http://tinyurl.com/ygoeapy
well done tboy2000. your 5min of fame!

I've become one of the Angry Birds because of the poor quality of NC's USB Cables.

I know this post is quite useless. I just wanted to vent out my frustration.
I just got off the phone with a B&N rep after 20 minutes of talking--because the rep kept beating around the bush and kept placing me on hold--and was told that I needed to callback on Monday to get the tracking no. for my 2nd--yup, this happened twice before--USB cable replacement. Yup, it broke again like the first one I got included with the NC--SIMPLY BECAUSE OF IT'S POOR QUALITY.
In generic micro USB cables, you would notice that most of them are made of rubber material, especially the one covering the tiny metal tip that you insert on the device's USB port, which makes them quite durable. Even if you bend it intentionally multiple times, the metal tip will not be affected that much. Only downside is, it doesn't fast charge the NC. In my experience, it takes a day and a half (about 36 hours) to be able to charge the NC fully. And yup, my NC is now turned off for a week (and counting).
The NC's stock USB cable however is made out of a gloss plastic material, probably to give way to the LED? light indicator? Downside is, it gets cracked/chipped off easily whether it was done unintentionally or not, because of the plastic material not being 'hard' enough, and that's where most NC owners like me are getting pissed off.
You have to be very careful whenever you charge the NC--you need to make sure that it's on a flat surface, not on a surface where it can sink itself say for example, a foam bed, so that the cable will not 'sink' with it in and put pressure on the metal tip, finally chipping off the plastic coating.
Do you guys know of any alternative that can fast-charge the NC like it's stock USB cable? Does anyone have the ability to modify the NC's stock USB cable to coat it with rubber or something to make it more durable?
I'm sure there are others who are experiencing these things. Hope we can gather around and start a discussion about getting a permanent fix. Maybe rally at a local B&N store or something, I dunno.
Well, a cheap and quick bit would be to wrap it with electrical tape. If you have an electronics store or Radio shack carrying it, there is also something called shrink tubing. this is a rubberish tube that when carefully heated with a heat gun (not a blow dryer) or a lighter, will shrink down around wires, or plastic.
But, I am rather annoyed with this serious design flaw as well. Would be nice if B&N either recalled these cables with a properly designed one, or get a 3rd party available to handle that.
I was thinking of reinforcing the plug end of the cable by encasing it in a big wad of epoxy putty.
epoxy putty usually cures to something a bit too brittle for what this really needs. As the OP said, the plastic on the plugs are really way too brittle for what it's meant for. other than those things, the other option I can think of is some of that latex dip sold in some hardware stores, or sex shops. wrap the metal bit in tape, then give it a few dips, let it cure, then carefully cut the tape off. instant rubberized plug. could even carefully cut an indicator window for the charge light.
heat shrink tubing sounds best. will try that. you can get it from home depot or lowes. get the multiple size package. it is really best to use a heat gun. if you dont know what your doing and use a lighter you will burn right through the heat shrink.
It sounds like you might be looking for Sugru. It hardens to a rubbery flexible consistency. There's also a how to floating around the web on making your own using caulk and ...baking soda? I think?
For that matter, a flexible clear caulk might do the trick.
I was thinking that RTV silicone (downside is long cure time) or maybe hot melt glue would be worth a try. Either one would be translucent enough to see the LED color. The Sugru looks interesting, although opaque like heat shrink tubing.
You could probably use something like Scotch Coat (more or less liquid electrical tape..) or plasti-dip perhaps?
*I'm still waiting on my NC to arrive. So, I'm not sure exactly which portion of the connector you're talking about. If it's the entire outside portion that is typically metal... this is normally a chasis ground which equalizes the chasis potential between the NC and whatever it's plugged into..., and really shouldn't be coated with anything
I ordered this off Amazon with the intent of fixing several things in my house. I was going to use the clear for the tip of the charger.
http://www.amazon.com/gp/product/B0027JIEPU
I think the shame of it is that all they had to do was use a strain relief sleeve like one of there:
Using the shrink tubing-
1. make sure you get a size large enough to get around the connection end.
2. Measure out a length. you want at least from the bottom of the N light to about 1/2 inch past the nub where the cord goes into the connector.
3. Slip the tube into place
4. Using a heat gun or lighter, carefully shrink the tube into place (NOTE: with a lighter, keep the flame moving, don't let it linger too long or you'll melt something)
5. If the resulting reinforcement doesn't seem enough, feel free to add another layer or 2.
WHAT DOES THIS ACCOMPLISH?
Well, most of the failure pictures I have seen, as well as the failed cord of my own, it seems the plastic is too friable (meaning it cracks really easy) to handle the stresses put on it at that end. Most of the cracks and fractures take place below the N, towards the cable side of the connection.
By adding this, it not only adds a semi flexible reinforcement around where it likes to crack up, it also stiffens and immobilizes a stretch of the cable, relieving a little of the stress that can happen in that part.
While other things might do the trick, and even electrical tape could do, this tubing is about the best option I've seen so far.
Srilania said:
While other things might do the trick, and even electrical tape could do, this tubing is about the best option I've seen so far.
Click to expand...
Click to collapse
Heat shrink tubing isn't a bad idea. I don't know how readily available it is in consumer stores and stuff... but I know I've used the Heat shrink tubing with the glue inside on quite a few connectors (higher end coaxial/heliax connectors tend to come with it). It's a bit thicker and more durable than typical heat shrink tubing, and the glue holds it solidly in place.
I used scotch tape. ugly, but it works.
Heat Shrink tubing shouldn't be too hard to find, most any electrical / hardware store should carry it, even Wal-mart will have it from time to time in the automotive section.
A better option may be plastidip. It gives a thick rubnery coating.
Sent from my NookColor using Tapatalk
After having a Nook Color for less than 6 months, mine just broke this morning! I would do without the LED indicator for a durable rubber casing.
Imbroglio said:
I was thinking of reinforcing the plug end of the cable by encasing it in a big wad of epoxy putty.
Click to expand...
Click to collapse
Epoxy works very well actually, but you need to put it on the inside, not the outside. Split open the plastic cover. Clean it up so it fits back together cleanly. Mix up a batch of translucent 5 Minute epoxy and completely fill the cavity with epoxy. Fit it back around the cable and secure it with a clip or clamp of your choice. A small binder clip works perfectly. After about 5 or ten minutes you can remove the clip and use an exacto knife to clean up the excess. Clamp it up again and
let it cure for 12 hours or so. Works well for me.
Triple wall heat shrink is just what you need. A heat gun (not a lighter, it won't work well) is the way to go. A hair dryer most likely won't have the heat needed.
I use the stuff in my home business and have tons of it...if you need some let me know!
I bent the male end that plugs into the nook unit... I Pressed the male end against a counter in my kitchen so it was bent back into place, put a few spots of super glue (the kind you get at the dollar store) and waited overnight for it to dry. good as new, no more wiggle or bend in my usb end.

My semi DIY car mount.

So lately I've been trying to figure out a way to get my tablet mounted at the optimum position for GPS usage without obstructing anything. In my van I have the Arkon seat bolt tablet mount, which is perfect because it keeps the tablet lower in the dash area so it's not blocking my view or baking in the sun, and it's also a solid mount point. I'd have no where else to mount it in the van aside from the window if it wasn't for this mount, and I absolutely don't like window mounting anything bigger than a cell phone. So in that instance, things work out great. Recently I put that Arkon mount in my car, which is a Hyundai Elantra. I thought since the distance from the seat bolt to the mount area would be less, I'd have more (if anything, too much) "neck" to work with. It turned out to be the opposite. My Elantra is stick shift, so when I had the tablet mounted in the most convenient spot that reached, I was all but punching the screen when I went to 3rd/5th gear. The only other alternative was to have it sitting over in the passenger area, which works for me but it adds as a huge inconvenience to any passengers in that seat since their left knee is where the tablet is. As a result I decided to put the Arkon seat bolt mount back in the van and work on something else for the car.
I have an empty space under my head unit for random storage, etc. I began to wonder if I could somehow utilize that space for incorporating a mount there. It would be the perfect height because it's higher up from the gear shift and it would definitely be optimum viewing for GPS usage. Originally I made the perfectly sized wooden block that had a slight slight slope to it so it would wedge itself in place. I then epoxy'd a BluRex Amazon case to it that I wasn't too happy with and was no longer using. This proved to be an awesome 10 minute mount, but it also gave me zero adjustability. I began to think was going to be important since last time we were on a road trip when the road I was on was going to be 3 hours long my wife watched a movie, so I knew I'd want a way to move it around for best viewing in multiple scenarios.
Here's two pictures from that build:
http://i.imgur.com/dsfQx.jpg
http://i.imgur.com/guw86.jpg
I began to give it more thought. I knew that the empty space under my head unit was going to be the mount point, but I just had to figure out how. I searched through multiple mounts, particularly from Arkon. In the end I bought this mount on eBay for about 20 bucks. It came with a suction cup which I knew wouldn't work for my uses. My plan was to cut the arm off, drill a hole into a wooden block, then fill it with epoxy and shove the arm in. The block of wood in question would be a piece that I cut to perfectly fit the open slot under my deck with a slight slant to it, that way as I pushed it in, it wedged itself in place (much like the last mount)
When I got this mount from eBay I began to wonder if I even needed to cut the arm off. Fortunately the height of the suction cup base was ALMOST the height of the opening in my dash. I figured all I had to do was wedge that in place and I wouldn't have to do the whole sha-bang with the wooden block and epoxy. I ended up cutting off the suction cup since it was useless in my case. The bottom of the plastic suction cup area had some flat ridges, so I figured I'd use double sided tape instead of epoxy to adhere it to a flat piece of wood. The flat piece of wood was to bump the thickness up just enough to replace the need for that wooden wedge.
http://i.imgur.com/yHOLR.jpg
http://i.imgur.com/l9mRO.jpg
http://i.imgur.com/O4Gin.jpg
http://i.imgur.com/KFJad.jpg
In the last picture you can see that I flipped things around. Originally I had the arm facing downward, but when I had the tablet mounted, 5th gear was still a problem as the gear shift would nearly hit the tablet. I knew if I flipped it upside down the arm would be facing upward, giving me some height... so I re-did the tape and put it on the other side. Since I mounted it more to the right (to ensure there was a super low chance of the steering wheel ever obstructing view, even if I was leaning far to the left while driving) I sensed a small amount of uneven stability since there was nothing keeping the left side tight against the roof of the opening. A small wooden wedge later and we were golden.
http://i.imgur.com/t7v4P.jpg
I ended up painting that wooden piece black to blend it in a little bit. I also noticed while driving that some roads had a degree of ripple to them, which would cause the tablet to sway back and forth. It didn't obstruct my view-ability of the screen at all, but if I was in an area where the tablet was casting a glare from the screen it became more obvious. On a hunch I pulled out two quarters and slid them under the arm mount, which is where I thought I was seeing a degree of flexing. Surprisingly it helped quite a bit and that area no longer has any flex. Not bad.
http://i.imgur.com/gzcV0.jpg
Final product:
http://i.imgur.com/LoUZT.jpg
Hopefully those of you out there who are finding some tablet mounts are *almost* perfect but not a home run can utilize some sort of DIY ideas like I did to make it work. I now have a solid mount for both vehicles, so no more worries about where the tablet will sit, etc. No complaints there. :good:
Great mod! I too have a compartment like that when I replaced my factory double din to a single din radio. To compensate, I had to put in a CD holder type opening, much like your area. I just have slots for CD cases. In my case, it wouldn't work out too well because my opening is held by epoxy and because of the texas heat, loses it's adhesiveness big time and alas, too weak for N7.
I have since bought a Kropsson Aero, which can hold both my tablet and Sensation. I do wish someone made a mount that can fit like the Aero can. Oh well, sorry to detract, just wanted to give you some kudos in getting a mount that works for you! :good:
I'm curious on how the epoxy is failing you. Is it not gripping like it should? A little side story - I epoxy'd a cracked side skirt in my first car, and when I got tires one day the hydraulic lift bowed the sides out pretty dramatically. (this wasn't a body kit - just lower siding from the factory. Here's a picture of a car nearly identical to what I had). It took the weight of my car for 30 seconds on that lift before the pressure was enough that it broke the epoxy bond. We may not have Texas heat, but here in Pennsylvania we have some crazy cold winters and some pretty muggy summers... I would think the differentiation wouldn't be good for epoxy when it's outdoors and hitting rain/snow/mud/hot/cold throughout the years.
I'm curious if the surface you epoxy'd wasn't really that optimal for epoxy. I say that based on my own experience recently, as I thought for sure epoxy would bond to anything, and for the most part it does, but take a look back at the first pictures of the BluRex/wooden block mod I did. I epoxy'd those two things together. After I took it out of the car and didn't use it, I wanted to see if I could somehow separate the two. I figured if anything the epoxy would separate from the wood and the epoxy would have just stayed gripping to wood particles from the block. But it was the opposite - the epoxy let go of the semi rubberized BluRex case, pretty cleanly too. It took a good amount of force, don't get me wrong, but once done it was a pretty clean break. I'm basing this entirely on assumption as I don't know what you were bonding together, but I wanted to throw out those FYI's as part of my epoxy experience.
So, that Aero can widen itself enough for a Nexus 7? I Googled around and I keep seeing screenshots of it with iPhones and Galaxy 3's... not tablets. That's wild if it does. Does your's mount based on suction cup? Or did you do some sort of additional mod?
JaSauders said:
I'm curious on how the epoxy is failing you. Is it not gripping like it should? A little side story - I epoxy'd a cracked side skirt in my first car, and when I got tires one day the hydraulic lift bowed the sides out pretty dramatically. (this wasn't a body kit - just lower siding from the factory. Here's a picture of a car nearly identical to what I had). It took the weight of my car for 30 seconds on that lift before the pressure was enough that it broke the epoxy bond. We may not have Texas heat, but here in Pennsylvania we have some crazy cold winters and some pretty muggy summers... I would think the differentiation wouldn't be good for epoxy when it's outdoors and hitting rain/snow/mud/hot/cold throughout the years.
I'm curious if the surface you epoxy'd wasn't really that optimal for epoxy. I say that based on my own experience recently, as I thought for sure epoxy would bond to anything, and for the most part it does, but take a look back at the first pictures of the BluRex/wooden block mod I did. I epoxy'd those two things together. After I took it out of the car and didn't use it, I wanted to see if I could somehow separate the two. I figured if anything the epoxy would separate from the wood and the epoxy would have just stayed gripping to wood particles from the block. But it was the opposite - the epoxy let go of the semi rubberized BluRex case, pretty cleanly too. It took a good amount of force, don't get me wrong, but once done it was a pretty clean break. I'm basing this entirely on assumption as I don't know what you were bonding together, but I wanted to throw out those FYI's as part of my epoxy experience.
So, that Aero can widen itself enough for a Nexus 7? I Googled around and I keep seeing screenshots of it with iPhones and Galaxy 3's... not tablets. That's wild if it does. Does your's mount based on suction cup? Or did you do some sort of additional mod?
Click to expand...
Click to collapse
I just got the Aero in actually. It doesn't fit the N7 with my Seidio Case installed. So it's a fail on my end. It fits my Sensation fine, but thats a given lol.
As for the surface areas, I think you are correct that maybe the surface I am trying to apoxy to (on the car) does not play well/adhere with the epoxy I put on. No biggie though. I wanted something off the dash anyways. I may just get the exogear/kropsson mounts eventually...
EDIT: semi DIY modding LOL...
Just getting back, regarding the Kropsson Aero. Because of the Seidio case making the N7 bigger than expected to fit in the Kropsson Aero, I decided to cut down the foam pads on the sides. Now the N7 fits! The said arms are maxed out, but I will try it in the car after work. I took pics, but my work computer is borking at the card reader. But I'll try to upload them at home if I have time ( I have a 4 yr old to contend with lol).
I did almost the same thing, except the empty space is above my stereo instead of below. I just drilled some holes in the top of it and fashioned a plastic mount that bolts in and connects to part of an Arkon mount. If I want to remove the mount, I can just unbolt the Arkon part from the part that's bolted to the double din kit and you barely notice the rest of it.
I did something similar with my GNex car dock so it wasn't on my window. I placed a adapter plate (see link below) so I could use the suction cup on some interior plastic below my stereo. It holds pretty snug, not sure if it would be enough to support a tablet though.
http://www.amazon.com/AP020-Adapter-Circular-Adhesive-Console/dp/B001DAT0XE/ref=pd_sim_cps_10
xxgoosexx said:
I did something similar with my GNex car dock so it wasn't on my window. I placed a adapter plate (see link below) so I could use the suction cup on some interior plastic below my stereo. It holds pretty snug, not sure if it would be enough to support a tablet though.
http://www.amazon.com/AP020-Adapter-Circular-Adhesive-Console/dp/B001DAT0XE/ref=pd_sim_cps_10
Click to expand...
Click to collapse
I have that same disk that came with my tomtom gps that I never used. But it works! I have it installed and holds the arkon mount fine without issues.
ydoucare said:
I did almost the same thing, except the empty space is above my stereo instead of below. I just drilled some holes in the top of it and fashioned a plastic mount that bolts in and connects to part of an Arkon mount. If I want to remove the mount, I can just unbolt the Arkon part from the part that's bolted to the double din kit and you barely notice the rest of it.
Click to expand...
Click to collapse
Nice! Do you have any pictures of the actual mounting point where the bolts are? I'm super curious how you accomplished this. :good:
JaSauders said:
Nice! Do you have any pictures of the actual mounting point where the bolts are? I'm super curious how you accomplished this. :good:
Click to expand...
Click to collapse
I don't, I'll try to grab one and post it here.

Made My own GameKlip with 3 feet of Stainless steel wire

so i was staring at this GameKlip accessory and thought, I could probably make one myself. They sell for about $20 including shipping online. Why not save some $ since I had the material.
What I used:
1 piece of 3" long and 1/8" thick stainless steel wire ( I got from a welding shop )
some shrink tubing from an electronics store, to protect the mounting points on the controller.
lighter or hair drier to shrink the tubing.
2 pairs of pliers to bend the wire
1 Sharpie marker to mark my bending points.
Playstation 3 Sixaxis wireless bluetooth joystick.
you can design as you see fit, but i started by bending the wire in half like a big V
bent the curved part 1/4" down @ 180 degrees. this is my anchor point for the joystick. this part goes right between the thumb sticks at the back.
from there i went underneath the joystick, making small bends to follow the contours of the controller.
NOTE: this is where you slide small pieces of shrink tubing over the wire at any point you don't want scratches on your joystick. Keep adding more as you progress, if you make too many sharp bends, you wont be able to slide the tubing around the bends.
anyways from the bottom to the front the wire goes, again following the V shape and spreading towards the L1 and R 1 buttons.
from there I bent the wires up, again following the contours and adding shrink tubing. Every time i needed a bend, i marked the wire with the Sharpie first and eyeballed it. the great thing is if you mess up, just bend the wire back and try again.
After going to the top front of the joystick, i made mounting bends like the first one. now with two single wire ends instead. (see photo) went backwards a tad and curved back 180 deg foward again.
i bent the remaining wire into a smallish platform then back to the joystick again, aiming for the USB charging port for my final brace to hold the weight of the phone.
I finished off by joining the two loose ends at the bottom of the joystick again with the shrink tubing. Both ends in one piece of tubing.
now i need a cheapo eBay TPU rubber case to permanently glue/double side tape to the mounting platform.
In all it took me about an hour.
you can use a thicker gauge of wire to make the whole assembly stiffer, but that would be too hard to bend and possible damage your controller when putting it on or removing. I had to remove it many times during the build to test my bend angles and fit.
oh and if you're not feeling the MacGuyver-ness, buy a real one here: http://buy.thegameklip.com/
reserved
More pics without joystick
Nice work
thanks
on second thought, thicker,copper wire would be doable too, as you can easily solder the pieces any way you want, and its malleable enough to bend easily.
I thought about Aluminum Wire but its too soft and likely to come loose and make your hands all black from the oxidation. It would be light though
I may just tack weld a small sheet of metal to the platform part so i can stick a case on easier.
Maybe just punch some small holes in the TPU case and zip tie it to the frame....
Can we get a pic with the phone attached?
mr mystery said:
Can we get a pic with the phone attached?
Click to expand...
Click to collapse
He said in the OP that he needs to get a cheap case so he can adhere it to the mount.
Nice craftsmanship ^_^
Sent from my Kangadore 64
mr mystery said:
Can we get a pic with the phone attached?
Click to expand...
Click to collapse
Using an ultrathin 3mm case and double sided tape. I dont recommend this case for this job as its super hard to remove the phone from it.. A softer flexable TPU case is best.
Sorry for the bad photo, using my Nexus 7 for a camera blows.
The last 3 photos from my Note 1. Anyways the finished product. Enjoy.
What about modifing this car mount to clip in and out?
Sent from my SCH-I605 using Tapatalk 2
Dakota0206 said:
What about modifing this car mount to clip in and out?
View attachment 1572530
Sent from my SCH-I605 using Tapatalk 2
Click to expand...
Click to collapse
looks good but likely cost way more than its worth. may as well just spend the $20 for an original one. you'd still have to make a clip on part and bond it to that mount.
Good job buddy. And here I am, thinking about spending the $25 bucks to get this item n' all.
See this one
Such wow, reviving a very old thread.
My next target controller will be the Dualshock 3.

Categories

Resources