After searching for answers... Screen taps not responding - Tilt, TyTN II, MDA Vario III General

Hi there. I picked up an important call whilst in the shower. Very little water fell on my Kaiser but I belive that this caused the screen to stop working. Or I have dropped it as well.
Now I tried the business card remove dust particle trick. Didn't work. So I disabled cube / Touchflo. Then I reinstalled my ROM. Basically, I can't align the screen... I tried using the Remote Screen Alignment tool as well.
What's weird is that when you leave the phone for a couple of seconds, the battery conservation feature kicks, and when I touch the screen, the screen powers back up. So I know the screen works but just not properly.
Do I have to replace my screen (or just the TOUCH component of it)? I'm not too good with hardware but can I take it apart and fix the problems?
EDIT: For those facing similar problems, use the trial version of SOTI Pocket Controller to work on your Kaiser remotely.

I'm sure someone knows what to do... please help.

I had the exact same issues you were having, I had to send it in finally so I hope it is warrantied.

jallenclark said:
I had the exact same issues you were having, I had to send it in finally so I hope it is warrantied.
Click to expand...
Click to collapse
nope, its out of warranty. I'm thinking of using pocketpctechs or some other similar service. Any suggestions?

I would just order a new screen and replace it yourself.

jallenclark said:
I would just order a new screen and replace it yourself.
Click to expand...
Click to collapse
Did they replace the entire screen or jus the TOUCH component? I heard that the TOUCH surface is way cheaper.
Also, I'm not too sure how to replace it myself.

when my tilt was in warranty they just gave a new device but on the call they said the screen was dead even though it displayed and had minimal responce.
I could be wrong but I don't think it would be easy (if even possible) to replace just the touch surface of the screen.

Related

Erratic behaviour of Trinity

Is anyone having an idea on how to handle the following:
- Start menu is opening and closing by itself, and
- after a while the device stops to respond to any input on the touchscreen, while other functionalities seem to be OK;
- neither a soft nor a hard reset help. The screen remains 'frozen' until... again difficult to say why, it recovers and then ...all over again as above.
thanks,
Nic
I had the same problem after about 2 weeks of use. Turn off, soft-reset, hard-reset didn't help at all. Leaving the phone off for couple hours helped but the problem occurred again. Very frustrating. I have contacted the HTC support but still haven't received any responses from them. I think it's the hardware problem.
This is either a motherboard problem- it has occurred on some Trinity and Hermes devices and involves the screen controller chip; or it could be a problem with a screen protector (if fitted ) causing pressure around the edge of the screen
I had the same problem. Sent my device to HTC and they replaced the motherboard. When I got it back, I thought all is well. The drop down menu started again so I sent back to them with a nasty message. It is in repair now and hopefully they will fix it again, change the motherboard and the screen!!!
Hello Gilbert,
When you send to them, you had to pay the shipping fee?
nbc17 said:
Hello Gilbert,
When you send to them, you had to pay the shipping fee?
Click to expand...
Click to collapse
Hi,
Oh yes. twice already and this pisses me off. When they sent the device to me the first time after claiming it was fixed, i did not have to pay for shipping costs. Let's hope they fix the bloody device soon or I am going to change brands.
Thanks,
Gilbert
I saw that problem on youtube
http://www.youtube.com/watch?v=KYfohqde2E8
Man I really hope mine doesn't have that problem, I wonder what it is? Let us know what happens when you get it back, again.
Dam, wtf, while reading this thread my Trinity started to act exactly as described in the above posts!!! IT'S contagous! Seriously... I do have a screen protector... Hope it rights itself....
This is really terrible...
http://youtube.com/watch?v=KYfohqde2E8
Hi there,
After having used my Trinity for 4 weeks I am experiencing same problems of erratic behavior, the start menu is activating itself and as a consequence device is slowing down gradualy up to the point where it freezes. I tried, soft/hard resets, removing battery etc. but nothing seemed to work. I have not installed the screen protector yet, so I can rule out straight away the effect of the screen protector. First I thought it could be jog dia lwheel which might be faulty, then it crosses my mind that it could be some virus. I donwloaded some applications off the internet. Before I found this thread I was considering of deleting the ROM and replacing it with another one, but it seem that the issue is more of hardware origin rather than software related. What happend after you got it from the repair? Is it working now? Cheers.

Tilt no longer enjoys being touched.

So, i'm usually quiet on these forums. Just reading, trying roms, etc. But here is something that has me stumped. Last thursday my phone crapped out. When i woke up and looked at it (it was connected to my laptop/charging) Applications were opening left and right, i couldn't close any of them because stuff kept opening. I tried to soft reboot it and it didn't help. Once it rebooted stuff started opening itself at random again. I ended up pulling the SIM and battery out and leaving it for 5 minutes. When i put it back and powered it up the touch screen no longer worked, but apps weren't opening on their own.
What gives?
I have hard reset (which means it's waiting for me to touch the screen to setup my rom), i have also taken off the screen protector (in case it had something stuck under it. Neither of these things helped. Per the forums I got a new screen, just put it in, and the touch screen doesn't work still... I'm drawing a blank here can anyone give me some advice. Going back to my Prophet for the time being but I HATE not having a keyboard (and it's slower than molasses)
have you tried flashing a new rom via sd?
Check that the screen protector has not moved under the front bezel and keeps pressing your touchscreen.
Robert
I have totally removed the screen protector and even replaced the screen for that matter so I dont think that's it. I haven't tried flashing a new rom. I just found it odd that this has worked for so long and now I get what appears to be hardware problems. As for flashing Via SD memory, is that better than doing it via cable for some reason? I'd be willing to give it a go...
Any other suggestions?
fiddelm3742 said:
I have totally removed the screen protector and even replaced the screen for that matter so I dont think that's it. I haven't tried flashing a new rom. I just found it odd that this has worked for so long and now I get what appears to be hardware problems. As for flashing Via SD memory, is that better than doing it via cable for some reason? I'd be willing to give it a go...
Click to expand...
Click to collapse
Similar problem happened to my Kaiser phone, although no multiple files opened, the phone just won't react to any touching, not stylus pen either. So I first soft reset, then hard reset, none of them works, now the phone can Sync alright, but the screen just stands on the Window Mobile screen, saying "Tap the screen to set up your window mobile device"
I only have this new phone for <3 weeks.
I went to HTC site, want to download a latest ROM file from them, after typing in the S/N, it won't let me, saying that ROM is not suitable for my phone.
So now I am download ROM file from this site, will choose one to flash the phone, see whether it works.
I will call HTC tech support tomorrow after Thanksgiving, see what they suggest
Hope some gurus here can also make some suggestion, Thanks!
Well I replaced the LCD and the new LCD works great, but the screen still doesn't respond to touches. What gives?! I hard reset and I got past the windows screen alignment thing by creating a welcome.not file but it's still pretty much worthless w/o a touch screen. Anyone have any suggestions?
Whoa, i thought something odd was going on. Never mind i got entirely the wrong idea.
Ha, not the case.
Anyone know if a flex cable would fix my issue? I dont really know what the felx cable is for but i've seen posts about people replacing them w/ LCD problems. I don't know if it is touch screen related or not, and i'm kind of tired of buying parts that don't fix my problem
please just flash a new rom whch ever you want (for some reason i thought you said that it keeps restarting your device because if that was the case the only option you would have was to flash via sd as activesync would load long enough for you to get a connection to flash from the computer)..trust me just try it..what have you got to lose
I reflashed one yesterday actually. The newest HyperDragon (which is looks like a new one is available today) It wasn't rebooting but initially windows were popping open left and right so i restarted it a couple of times(which i first had the problem, not yesterday) Yesterday it worked like any normal rom w/o the ability to touch. Anywho, after the flash of a different rom. No luck. I'm thinking it's a hardware problem of some sort but as i've already replaced the LCD i have no idea what?
yah thats sounds funky..you can bring it in for a warranty exchange either at a local DSC or over the phone (that is if your with att) and if not call HTC..all devcies come with a 16 or 18 month warranty
Well I called ATT yesterday, apparently I purchased the phone On Oct 17th 2007 which means It's out of warranty (apparently it has a 12 month warranty?) So it sounds like I'm SOL. So, i guess I'm off to ebay to try and fine a phone that I can canibalize to try and get mine going again.
touch screen
this may sound dum but when you replaced the screen did you replace the touch part as this is different from the screen
Well I picked up this
http://www.blackberry8100parts.com/...B3-NEW-HTC-TyTN-II-KAISER-P4550-_p_35-70.html
which includes the digitizer (from what I know it's all one part when they send it to you) The screen has the digitizer built in. So i replaced the part they sent me.
I just stated having this issue. My touchscreen stopped responding to touches over the weekend while the keyboard was extended. I just took the phone apart to make sure everything was connected right & put it back together, & now the touchscreen doesn't work at all. This sucks!
Any news? i'm having the same problem: no response at all, stuck at "Tap the screen to set up Windows Mobile-based device"
An interesting problem with screen
well my tilt fell out of the car holster while using gps and i suspect the screen hit my gear shift. I didn't notice anything odd after i put the battery back in it (yeah it fell that hard lol). Later that night I went to check mail and noticed something not right. Turns out my screen seems to have been pushed in a bit. Well here's the issues I've noticed so far: All the touch responses seem fine except for 1) the screen alignment doesn't register taps, but otherwise the touchscreen works and 2) on the htc home screen, I can't tap the house icon unless I tap any other icon first.
Initially I thought there was some pressure or deformation right at that particular spot, but it reacts the exact same way in landscape mode. I can't tap the house icon first; I have to tap something else first, then the icon works fine until I open a program or something and go back to the home screen. Then I simply have to tap weather or something and then home.
I'd reflash the rom or do a hard reset, but the screen alignment didn't work when I tried it so I didn't want to get stuck at the "tap your screen to begin" part.
Any ideas or do I just need to buy another screen or maybe just the digitizer. the amount the screen seems recessed is maybe a millimeter at most. Just enough so that I noticed a difference when touching contacts just above the housing. I tried cleaning by using a business card and running between screen and housing. Ohh... and one more thing... when I open the cube and then close it, I get what I refer to a static frazzle for split second and it goes back to normal. That only happened a couple of times after the business card thing. Do you think I just loosened a connection? damn... I still haven't taken it apart yet. Think I need to. Any help appreciated.
If your screen does not work, you can still use your phone. There is an app that you use on your computer that acts as the touch screen. This also works when the screen craps out.
http://www.sparus-software.com/spip.php?page=download&lang=en&ref=at&t=tilt
(EveryWAN Remote Support Personal Edition - Free download)
yeah -- my touchscreen didn't crap out totally, it just got muffed up when I dropped it a bit. Well, i went ahead and installed codefreaks remote screen alignment thing and did a hard reset. Well, the hardreset did the trick w/out the need for anything else. The alignment worked and everything. So, i'm back in business. Everything seems to work properly, except that my screen is still recessed a tad; but, that's not a big deal really.

Diamond touch screen not reacting when touched.

The touch screen of my htc touch diamond is not working properly. It does not react to my touch. For me to get it to work I have to rub my fingers over it then it will be work again as normal. This only lasts for a few minutes after a while it becomes non responsive again. It is like it has to be warmed up to get it to work. This a problem when it comes to sending text messages. (the problem remains when I remove the protective screen).
Anyone has a answer to this?
remember the last program you installed and remove it , maybe it cause this problem
or try hardreset
Tried both methods still not working. I have ran out of ideas. Anyone else expierenced this problem?
Im having the same problem with my Raphael
To really know whether it is a hardware problem or software based problem, I recommend a hard reset and see whether the problem persists...
this is likely to be water damage on the screen. send it off for warranty see if they fix it. they fixed it for mine.
The thing is iv noticed the touch screen isn't thermal reactive like most touch screens. In other words the temprature of your finger is sensed on thermal screens, the HTC you can use anything solid that makes contact. Usefull if you have long nails.
So I'm guessing its probably hardware if it works after a while of 'rubbing' it, But like otacon said I would do a hard reset before jumping to that conclusion.
Same problem
Hi there....i saw that this is an old thread but did you manage to get it to work?
Cause i have a HTC Diamond that i changed both the displays on(LCD and the "point screen") and everything works fine on mine now,even tried to recieve phonecalls and it works excellent so as i said EVERYTHING works like a charm but the touch function.....it doesn´t react in any way while trying to use the touch function and i have tried soft reset,hard reset,new rom,checked all the internal connections around 4-5times and everything is ok but the damn touch function won´t work whatever i do with it.
I haven´t "glued" the 2 screens together,but they are sitting close to eachother so it should work anyways right?
Now from what i have seen on internet is that there are different versions of touch screens available on the market and i ordered the LCD from one company and the touch screen from another.
Could it be so that they aren´t compatible together or am i doing something wrong?
I´m still stuck at "Tap the screen to set up your Windows Mobile-based device" and can´t get any further after trying another rom.
Please help me out if it´s possible.
I have exactly the same issue you're experiencing, I've actual flashed the original rom, thinking that might put every settings in place to make it work, but no joy.
I don't be leave the concept of the weather condition equate to the performance of the device, as read in some of the forums. reason being I've had mine in very hot climate Country for over year whiles working on a project in Africa. In fact that was when I realised the the screen has become unresponsive.
I think this is a hardware issue.
It´s working perfect again
So since my last reply i ordered a new touch digitizer and lcd display and soldered them together carefully(first time i bought a lcd and digitizer from two different companies so they weren´t compatible with eachother and made the touch defective and second time i bought both digitizer and LCD screen from the same company and then it worked) and it has been working perfect since i last wrote my comment so i recomend you check the contacts/connections first on the phone because i had some minor issues with them when i assambled the phone again so i had to #wiggle# the contacts so i made sure they were connected.
We had a company here that sold lcd displays and digitizers out for a total of 30dollars with shipping so i had nothing to loose on it so that´s why i ordered a new set again and that made everything work as a charm since i replaced it.
Now i have searched online about the displays and the digitizers and i have found out that there are atlast three different versions of them so if you order a digitizer and a LCD make sure you atleast order both from the same company so it doesn´t happen the same to you what happened to me the first time.
Cheers and hope i helped you somewhat or else just ask on and i should try to answer.

[POOL] About the touchscreen problem

I only discovered the touchscreen issue yesterday doing the test of the other thread. So, i would like to every z1 owner to answer this pool to know how bad things are and if we can try to find a solution, since i think Sony won't.
So, please answer the poll and post any useful information. I'll start.
My phone model is C6943, I currently don't use case and I'm using a screen protection. I can do the xperia touchscreen test without touching the phone body without problem and also doesn't have problem with pattern password.
ffp. said:
I only discovered the touchscreen issue yesterday doing the test of the other thread. So, i would like to every z1 owner to answer this pool to know how bad things are and if we can try to find a solution, since i think Sony won't.
So, please answer the pool and post any useful information. I'll start.
My phone model is C6943, I currently don't use case and I'm using a screen protection. I can do the xperia touchscreen test without touching the phone body without problem and also doesn't have problem with pattern password.
Click to expand...
Click to collapse
Pool? I think you mean "poll"
My 6902 is completely screwed. At first I used a screen protector and the problem wasn't too bad. Then I removed it when I took the phone in to get another issue fixed and soon after that the problem got very bad. I was traveling so couldn't go back to the service center. Now it's a bit better, randomly works and randomly doesn't. When I was home in cold weather though it seemed a lot worse than it is now that I'm back in India where it's warm. Not sure if temperature is a factor, or could be conscience. But a few weeks ago it was so bad you couldn't type even a two letter word using Swype.
Also, I now have a part of my screen in the form of a horizontal line where touch doesn't work at all. No single touch and no drag. Completely dead. Taking it to the service center soon.
You should vote on the first option, then
Guys, check my post "News from whats is causing touch screen problem" to see if is your case!
ghostman2 said:
Guys, check my post "News from whats is causing touch screen problem" to see if is your case!
Click to expand...
Click to collapse
It's not.
I got problem unlocking with patterns, scrolling pages and when I play some games after few minutes it stop working so I voted the first option. My phone is back to Sony, I hope they know what to do and at last it's Made in China.
Please, post if you use case and screen protections too. This could help understanding the problem.
Additional data : Z1 is being handled in a leather case, back and screen protector removed ( not the one with the logo, the plastic ones that makes your camera blurry )
Touchscreen problem seen in the game Alien Shooter, after some playing, the touch screen becomes less and less responsive ( i tap a button to shoot and use some onscreen joystick to move ) - both become unresponsive/less responsive as you play and the phone gathers some heat ( you can feel the touchscreen becoming hotter )
i have a simple tpu case, i had a bit of problem when playing all touch-based games (not ones with gyro like asphalt).
ever since i got the case it's better, i have the ASF and nillkin matte screen protector
ffp. said:
Please, post if you use case and screen protections too. This could help understanding the problem.
Click to expand...
Click to collapse
I did not use any case just a chip screen protector. Anyway on a good healthy touch screen the screen protector should not influence the touch screen respond.
Hey guys, I have also this touchscreen issue, and I would appreciate if you give a feedback about warranty service, if sony accepted the problem and replaced a touchpanel or not, and also if the replaced touchscreen is better or not. I´m also thinking about sending it back for warranty repair.
I have also found that my phones touch screen is temperature sensitive, when it get cold or warm it just refuses to detect touch actions. Try it yourself put the phone into cold/hot water for 5 second, take it out, quickly clean the display from water and test the touchscreen. I first tought this behavior is normal and I didn´t cared until I started to play games. After 15minutes of playing the touchscreen bug every time appears. But also after a while its randomly disappears. So this thing is strange. (the bug appears identically also when I have my phone in a plastic case)
Vippo321 said:
Hey guys, I have also this touchscreen issue, and I would appreciate if you give a feedback about warranty service, if sony accepted the problem and replaced a touchpanel or not, and also if the replaced touchscreen is better or not. I´m also thinking about sending it back for warranty repair.
I have also found that my phones touch screen is temperature sensitive, when it get cold or warm it just refuses to detect touch actions. Try it yourself put the phone into cold/hot water for 5 second, take it out, quickly clean the display from water and test the touchscreen. I first tought this behavior is normal and I didn´t cared until I started to play games. After 15minutes of playing the touchscreen bug every time appears. But also after a while its randomly disappears. So this thing is strange. (the bug appears identically also when I have my phone in a plastic case)
Click to expand...
Click to collapse
For me the warranty worked perfectly, i changed the phone 3 times until get a working one, i called Sony, discribed my problem and they changed for me, only 2 days for the change. BUT i recorded the problem and sent to them, so they accept the change.
Vippo321 said:
Hey guys, I have also this touchscreen issue, and I would appreciate if you give a feedback about warranty service, if sony accepted the problem and replaced a touchpanel or not, and also if the replaced touchscreen is better or not. I´m also thinking about sending it back for warranty repair.
I have also found that my phones touch screen is temperature sensitive, when it get cold or warm it just refuses to detect touch actions. Try it yourself put the phone into cold/hot water for 5 second, take it out, quickly clean the display from water and test the touchscreen. I first tought this behavior is normal and I didn´t cared until I started to play games. After 15minutes of playing the touchscreen bug every time appears. But also after a while its randomly disappears. So this thing is strange. (the bug appears identically also when I have my phone in a plastic case)
Click to expand...
Click to collapse
Same here. I sent my phone back last week to the store where I bought it 2 months ago. They will send the phone to Sony Center but the time for repair or replace the device will not be 2 or 3 days but from 2 weeks to no eta. When the phone will come back to the store they will send the phone to me. I will post if the problem persist or not.
The problem is if they return a phone with the same problem.
ffp. said:
The problem is if they return a phone with the same problem.
Click to expand...
Click to collapse
They should be aware about this issue even on the new device so at this time they probably will check that but if they return a phone with the same problem, I will send it back again like many did. Someone had to replace the phone 3 times and I will do the same.
IYeah, you will be a long time without your phone though. I think I'll wait a bit since i rarely get the error and actually only when i try to reproduce it. How bad was yours?
ffp. said:
IYeah, you will be a long time without your phone though.
Click to expand...
Click to collapse
What I can do, I want a fully working Z1, I paid for it.
ffp. said:
I think I'll wait a bit since i rarely get the error and actually only when i try to reproduce it. How bad was yours?
Click to expand...
Click to collapse
I was able to reproduce the problem in many ways, Touch Screen Test, Opening the phone with Patterns, Scrolling Pages or with Launcher instead of switch the page it was opening the applications and at last when I was gaming at one point the touch stopped working and I had to wait, so this made my mind to send it back. On daily use was all ok but in some circumstances was frustrating.
i had the problem with cm11. and when I retored to stock then the problem was gone:S
I'm on stock and I got the problem.
Today for the first time I got the problem when writing on handrite. So I thought about using my phone warranty to get anotehr one. But it don't always fails when i do the method to reproduce it. So, how do you test if your new phone is working and how do you prove that it isn't? I mean what if i take the phone to warranty and it works?
And for you who already changed phone, it is working?
ffp said:
'm on stock and I got the problem.
Today for the first time I got the problem when writing on handrite. So I thought about using my phone warranty to get anotehr one. But it don't always fails when i do the method to reproduce it. So, how do you test if your new phone is working and how do you prove that it isn't? I mean what if i take the phone to warranty and it works?
And for you who already changed phone, it is working?
Click to expand...
Click to collapse
For me after the 3rd change is working now, here is what i did: i recorded the error and send it togheter with the phone. They saw the video and changed imediately.
Sent from my C6943 using xda app-developers app
Did youu made the method to reproduce and it didn't failed? For how long do you have the 3rd phone?

Help with touch related problem

Hi guys,
My Xperia ZR started behaving abnormally some days back, I put "screentouchtest" app and found that there were random inputs on the phone which made the phone go useless... Check the screen shot attached.
So I tried to make an app that will disable only that part on my screen and I was successful at it... Check screenshot attached. I could then at least use my phone to some extent.
But now the frequency of these random touch inputs have increased and that has made it again go unusable...
Problem is that I made this app as a floating app and whenever user touches other part of the phone , touch below the unblocked area is activated.
SO now I wanted to disable the touch completely over this area...any help will be appreciated.
Sony says it is due to water logging in the motherboard and no warranty will be given.
You are not alone!
Having the same problem here. Random touch inputs on the top right corner of device. I can assure you it's not because of water log of any sorts because i have opened ,checked, dried and even tested the touch display. Its a software related issue I guess which I am not able to pinpoint or understand. I wish someone from the forum helps with it.
water logging? did your phone get wet some time? its waterproof phone and no warranty given? :laugh: screw sony in consumer court
highevolutionary said:
Having the same problem here. Random touch inputs on the top right corner of device. I can assure you it's not because of water log of any sorts because i have opened ,checked, dried and even tested the touch display. Its a software related issue I guess which I am not able to pinpoint or understand. I wish someone from the forum helps with it.
Click to expand...
Click to collapse
If you think its a software problem, i'll try putting some custom ROM.
sourabhp said:
water logging? did your phone get wet some time? its waterproof phone and no warranty given? :laugh: screw sony in consumer court
Click to expand...
Click to collapse
Yeah I know Its waterproof. My brother was using it so not sure if there was water logging. But when we went to customer service the condition of the mobile was not good(Plastic that covers charging port was loose) so couldnt fight actually.
Custom rom doesn't help
Engic0 said:
If you think its a software problem, i'll try putting some custom ROM.
Yeah I know Its waterproof. My brother was using it so not sure if there was water logging. But when we went to customer service the condition of the mobile was not good(Plastic that covers charging port was loose) so couldnt fight actually.
Click to expand...
Click to collapse
Sorry to say unfortunately custom ROM doesn't help either. After I installed one just to see if the problem persists, To my surprise it didn't! But after a week or so the pendulum was back to square one. So I had to roll back. I really don't know how to go about this problem I think the problem is because of a bug of some sorts which causes the chip to send signals to the display addressing that its being touched or whatever. Anyway this is just my guess. You can try installing a custom ROM for your device and see if the issue ceases. In that case my problem would be just device specific. Do share your results after you install a custom ROM :good:.
highevolutionary said:
Sorry to say unfortunately custom ROM doesn't help either. After I installed one just to see if the problem persists, To my surprise it didn't! But after a week or so the pendulum was back to square one. So I had to roll back. I really don't know how to go about this problem I think the problem is because of a bug of some sorts which causes the chip to send signals to the display addressing that its being touched or whatever. Anyway this is just my guess. You can try installing a custom ROM for your device and see if the issue ceases. In that case my problem would be just device specific. Do share your results after you install a custom ROM :good:.
Click to expand...
Click to collapse
May be there is a problem with the touch digitizer under the LCD panel which is misbehaving. No software can fix it. You will need to replace the touch digitizer along with LCD screen as they are sold as single unit. Check online if you can find the parts and ask any local mobile repairer to replace it. :good:
NO Luck with Custom ROM
I put Android Lollipop (CM12 Port) and there have been no change. Looks like the problem is with digitizer, last time I told local repair shop to replace the screen they said they cant separate the screen and had no clue. But I searched and found out from youtube videos that it can be done. Now all I have to do is buy Screen+Digitizer.
As you can see the random touch strip have moved little upwards from my earlier screenshots. That happened months back. If anyone wants the app I made then let me know. It helps me to some extent.
Engic0 said:
I put Android Lollipop (CM12 Port) and there have been no change. Looks like the problem is with digitizer, last time I told local repair shop to replace the screen they said they cant separate the screen and had no clue. But I searched and found out from youtube videos that it can be done. Now all I have to do is buy Screen+Digitizer.
As you can see the random touch strip have moved little upwards from my earlier screenshots. That happened months back. If anyone wants the app I made then let me know. It helps me to some extent.
Click to expand...
Click to collapse
LCD with digitizer is around INR 4000
Which app did you make? What does it do?
sourabhp said:
LCD with digitizer is around INR 4000
Which app did you make? What does it do?
Click to expand...
Click to collapse
Where can I buy 1? Online? Link Please...
Since there are random touches on my phone, I made app that blocks this touch... Check the screenshots, I have "Show Touches" Option ON from Developer Settings. This makes all the touches show white marker... So I made app that floats over the screen and wont show any response when there are touches over that area. "Semi Transparent Area" in the screenshot - Touch wont work over that part. App wont completely disable the touch though, if we press other part of screen for that time app gets disabled...
Engic0 said:
Where can I buy 1? Online? Link Please...
Since there are random touches on my phone, I made app that blocks this touch... Check the screenshots, I have "Show Touches" Option ON from Developer Settings. This makes all the touches show white marker... So I made app that floats over the screen and wont show any response when there are touches over that area. "Semi Transparent Area" in the screenshot - Touch wont work over that part. App wont completely disable the touch though, if we press other part of screen for that time app gets disabled...
Click to expand...
Click to collapse
https://www.google.co.in/?gfe_rd=cr&ei=8BTTVIDzOc6AuASH8oCQCQ&gws_rd=ssl#q=sony+xperia+zr+lcd
Use google with different keywords
sourabhp said:
https://www.google.co.in/?gfe_rd=cr&ei=8BTTVIDzOc6AuASH8oCQCQ&gws_rd=ssl#q=sony+xperia+zr+lcd
Use google with different keywords
Click to expand...
Click to collapse
lol Okay
SOLUTION!!
Engic0 said:
lol Okay
Click to expand...
Click to collapse
Finally, a solution. Time for a digitizer+screen. Thank you guys.
Hey what is the app you made? I'm in the same boat but can't really afford a new digitizer....
Yep i need it too. It will be greatly appreciated if you share your app here. Thanks in advance.
Sent from my Sparkle V using Tapatalk
sorry guys for late reply!
I am attaching the apk here...
I have this problem too but it only happens if the phone screen get wet
Some time it happen randomly but when i press on the screen at bottom and on led gently it disappear and back to normal
Thank you!
The Float APK solved the major issue of my faulty touch screen in my Nexus 4. There are two lines in my screen where the touch is not working anymore. One of them is having several crazy clicks making my phone somehow useless. By using this app, I can prevent that, which is great!
Two issues I've got:
- the textbox to set the distance from the top is located exactly in the first dead line! So I need to turn my phone sideways to be edit to click there and edit its value.
- when using the phone in horizontal mode, blocked zone turns as well, but the faulty zone is fixed there.
I'm wondering if you might share with us the source code or maybe you consider to make some improvements on it?
Thank you so much for sharing this app here!
thanks for this app solution.
I too have problem of ghost touches. This app definately helps with that and makes the phone somewhat usable again.
The only problem is that some ghost touches are continous (it's like someone presses their finger on the screen and keeps holding it there). This makes action by other touches unresponsive.
Maybe we can find a solution for this in the float app?
Source code for the app
Finally since many of you requested, here is the source code! - Stop Touch - Source Code

Categories

Resources