Help please stuck in bootloader - Tilt, TyTN II, MDA Vario III General

After a good update of udK 8.0 R2 Vega on my Tynt II, I try to update the radio too, unfortunatelly at 99% this crash !!!
Now my device is always in Bootloader mode, I don't know how to exit from it, I tried to reinstall udK 8.0 R2 Vega but the updater say ERROR:
Please what to do to exit from bootloader mode ?
Giuseppe

uniprof said:
After a good update of udK 8.0 R2 Vega on my Tynt II, I try to update the radio too, unfortunatelly at 99% this crash !!!
Now my device is always in Bootloader mode, I don't know how to exit from it, I tried to reinstall udK 8.0 R2 Vega but the updater say ERROR:
Please what to do to exit from bootloader mode ?
Giuseppe
Click to expand...
Click to collapse
Here download attached file. Then run it and type in readconfig and record the results here. Or you can just try typing in boot
let me know if this helps hopefully it does.

I followed your instruction and used your program, after hard reset there is again bootloader mode, I tried to reinstall udK 8.0 R2 Vega but stop on 0%.
Help me !!
Giuseppe

uniprof said:
I followed your instruction and used your program, after hard reset there is again bootloader mode, I tried to reinstall udK 8.0 R2 Vega but stop on 0%.
Help me !!
Giuseppe
Click to expand...
Click to collapse
ok once you type boot, what happens?

follow these steps then:
1. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
2. put your device into the cradle
3. Run mtty and Choose WCEUSBSH001 in 'PORT' (if it doesn't show then you didn't stop all active sync processes above!)
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset. (for some devices it can also be "set 14 0")
5. type "task 8" to get your device formatted
6. type "task 0" to ask your device reboot
7. take the device out of the cradle, and manually reset it if it does not do that already.

i hope you have hardspl installed otherwise you can brick your device and thats not a pretty thing.

Thank youuuuuuu !!!!!
I was able to reset the device, all ok now.
But if I try to reinstall again the radio update, it stop at 99% and say update errror.
Then I have to re-follow your instruction.
How can I successly install the radio update ??
Giuseppe

uniprof said:
Thank youuuuuuu !!!!!
I was able to reset the device, all ok now.
But if I try to reinstall again the radio update, it stop at 99% and say update errror.
Then I have to re-follow your instruction.
How can I successly install the radio update ??
Giuseppe
Click to expand...
Click to collapse
do you have hardspl installed?

hehehhee noooo , I install it now, I will let you know.

uniprof said:
hehehhee noooo , I install it now, I will let you know.
Click to expand...
Click to collapse
haha you are lucky you did not ruin your device. Hopefully everything runs smoothly from here. Let me know if I can help you further.

redbandana said:
do you have hardspl installed?
Click to expand...
Click to collapse
You are the best, no body help me before like you.
Thank you.

uniprof said:
You are the best, no body help me before like you.
Thank you.
Click to expand...
Click to collapse
You're welcome and I am glad everything turned out well for you.

Hi Morning, do you know wich is the best ROM arround ?

uniprof said:
Hi Morning, do you know wich is the best ROM arround ?
Click to expand...
Click to collapse
I will tell you if you tell me the best car around.
The best woman around.
The best city in the world to live...
Be aware - these actually have to be the BEST in their category - not just YOUR opinion.
Get the idea? You are gonna have to read and flash for yourself to see what YOU actually think.
Bill

Related

Phone locked in bootleader!! Cannot even Hard Reset!!

Hi,
I wanted to update my trinity in the version of S300+ (French) with the original HTC ROM.
Not only it didn't work, but I lost my phone, I cannot access anything even with Hard Reset and battery removal...
When I want to upgrade, it's going till 1% and then it stops and I'm getting a message "Error 286" Cannot connect with phone.
I cannot hard reset, I cannot do anything! When I hard reset, I'm always coming back to the bootloader (I think it's the bootloader, the screen with colors, where it says numbers and it's says USB).
Any idea? A upgrade with miniSD will help?
Thanks!
Start flash utility again and wait untill it starts again (can take sometime).
I had it to when I first flashed a rom.
Hi,
I tried it already, but it's always blocking at 1% of progress and it's telling me in the computer Error 286, and the phone resets and comes back to the bootloader...
Any idea?
I just tried now to update the ROM with the HTC_Trinity_SIM_CID_Unlock_v1, it's going till 14% but then it stops...
Any idea, please?
I cannot send back my device to warantee because updating roms is forbidden...
This will solve all your problems:
http://forum.xda-developers.com/showthread.php?t=308691
sharedworld said:
I just tried now to update the ROM with the HTC_Trinity_SIM_CID_Unlock_v1, it's going till 14% but then it stops...
Any idea, please?
I cannot send back my device to warantee because updating roms is forbidden...
Click to expand...
Click to collapse
Put the phone in BOOTLOADER, then disactive ACTIVESYNC (form menu). After then start MTTY (you found it in the forum) set it on USB and then give the command:
task 32 Enter
task 28 Enter
task 2A Enter
info 8 Enter
task 8 Enter
After the last command the PDA restart and then you make a normal flash.
I concur :
http://forum.xda-developers.com/showthread.php?t=308691
after 1/2 a day wasted on the agony of a my problem phonem I finally managed to get pof's sxpliot to work, and I promise, it does.....
qubit76 said:
I concur :
http://forum.xda-developers.com/showthread.php?t=308691
after 1/2 a day wasted on the agony of a my problem phonem I finally managed to get pof's sxpliot to work, and I promise, it does.....
Click to expand...
Click to collapse
Please give more instruction howto
Can't you just reflash it with an original SFR ROM? And then read correctly all the instructions for the wm6 flash?
biohazard said:
Can't you just reflash it with an original SFR ROM? And then read correctly all the instructions for the wm6 flash?
Click to expand...
Click to collapse
SFR dosen't give any ROM... But the problem is that I cannot get out the bootloader, but I'll use the solution given here.
Thanks!
sharedworld said:
SFR dosen't give any ROM... !
Click to expand...
Click to collapse
Looks there]...and flash again
shym said:
Looks there]...and flash again
Click to expand...
Click to collapse
It's a DUMP... And not a full one... For ex. you do not get the splash screens...

cingular 8125 freez on splash.

Hello.Sorry for wrong english.
my problem is on cingular 8125
I bought it with problem.
On splash screen it freeze, i flash RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1,because it firmware for cingular 8125. and it freeze too.
Can you help me?
my ipl 2.25
spl 2.25
gsm 02.25.11
os 2.25.11.1
Thank you. and again sorry for wrong english.
Ok Dude here is your solution ive found it myself after Searching
I will not be liable for Bricking your Device you do this at your own Risk*
First of All Is your Phone CID unlocked?
if it is check to see if you can hard reset if your phone says Format is Failed then here is your fix
First flash factory rom
grab a minisd that is blank *Warning it will Overwrite any card you put in*
enter into bootloader
reset+ camera button
in windows xp
Download mtty
http://forum.xda-developers.com/attachment.php?attachmentid=71806&d=1203597568
Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
run program
set port to
\\.\WCEUSBH001
click OK
*Warning it will Overwrite any card you put in*
type in at CMD>
r2sd all
then press enter
after it finishes reset pda and return back into bootloader mode
reset+ camera button
it will ask if you wish to flash from sd press Voice Command button to accept
after 100% complete reset phone you should be able to get back
hello. thank you for a help. mtty says me You didn't get the proper security level to download a specific image. why i do wrong?
cg_ar said:
hello. thank you for a help. mtty says me You didn't get the proper security level to download a specific image. why i do wrong?
Click to expand...
Click to collapse
Your phone is CID locked,Mtty will not work in this situation. Have you tried a Hard Reset.
Does it display any error message while flashing the official Rom,does it complete flashing or stops with a error message ?
Which windows you are flashing with,WinXP or Vista ?
when hard reser it says me a fat format failed. all sw flash without problem.
Anybody know how this is repair? (sorry for wrong english)
cg_ar said:
when hard reser it says me a fat format failed. all sw flash without problem.
Anybody know how this is repair? (sorry for wrong english)
Click to expand...
Click to collapse
how it cid unlock in bootloader mode?
cg_ar said:
how it cid unlock in bootloader mode?
Click to expand...
Click to collapse
You cannot CID unlock in the Bootloaders,it has to have a working OS (Rom),try to flash a rom,try these roms,lets hope one of them might work, Button's Rom 1.05 or xda_minis_launch or wizard_love_rom and official rom of your carrier and if there's any sdcard/mini_sdcard inserted in the phone,take it out before flashing,just keep on trying the different roms,its a catch 22 situation,it won't let the rom flash,stuck at splash screen and still it won't get CID unlocked in Bootloaders or use the Mtty method.I can imagine your frustration,but you gotta keep on trying.
i tried Xda_MiniS_LaunchROM_v154102,wizard love,button and original rom from cingular. and it freez on boot at all roms,and cannot make a hard reset. what i will doing next?
in this condition phone is not repairable?
cg_ar said:
in this condition phone is not repairable?
Click to expand...
Click to collapse
YES ! it is repairable,but not free,you'll have to pay for getting the CID unlock code from 'imei-check' uk.They might charge you around 20 or 30 dollars and provide you with a unlocking code,after that you'll be able to flash any Rom,but,here we were trying to get it working free somehow! Anyway, the choice is yours now,but certainly it is repairable,don't loose hope !
zabardast_1 said:
YES ! it is repairable,but not free,you'll have to pay for getting the CID unlock code from 'imei-check' uk.They might charge you around 20 or 30 dollars and provide you with a unlocking code,after that you'll be able to flash any Rom,but,here we were trying to get it working free somehow! Anyway, the choice is yours now,but certainly it is repairable,don't loose hope !
Click to expand...
Click to collapse
I know a way to avoid paying and manage a security_level=0 to allow "r2sd all"
It's just a matter of flashing a SoftSPL for G3 and use mtty
"Hello,
if the device doesn't boot up in windows then unlocker it will not work!
Regards,
IMEI-CHECK Team"
it says on imei-check.
how i will did?
what is softSpl for g3? please give url. thank you
mestrini said:
I know a way to avoid paying and manage a security_level=0 to allow "r2sd all"
It's just a matter of flashing a SoftSPL for G3 and use mtty
Click to expand...
Click to collapse
hey m8
You referring to 'JumpSPL' or something ? thats interesting
cg_ar said:
"Hello,
if the device doesn't boot up in windows then unlocker it will not work!
Regards,
IMEI-CHECK Team"
it says on imei-check.
how i will did?
what is softSpl for g3? please give url. thank you
Click to expand...
Click to collapse
hmmm, so imei-check' said that,yeah ! I presume,you got to have a working OS (Rom)
Well, softSpl for G3, I'm not sure myself,let mestrini handle this.
zabardast_1 said:
hey m8
You referring to 'JumpSPL' or something ? thats interesting
Click to expand...
Click to collapse
Something like that
If i recall correctly while developing SoftSPL for G4, The Equinox also made a G3. Problem is no one ever thought of a use to it (until now, and i have others hehe )
mestrini said:
Something like that
If i recall correctly while developing SoftSPL for G4, The Equinox also made a G3. Problem is no one ever thought of a use to it (until now, and i have others hehe )
Click to expand...
Click to collapse
WOW !
I'm all anxious here...... eyes n ears !!!
i download a wzg3.7z. unpack and have
Hard-SPL.nb
JumpSPL.exe
SPL.lnk
spl.nb.
it has in pack 145kb is it alright?
and jumpspl cannot execute and spl.ink too. How this flash?
cg_ar said:
please mail me softspl for wizard g3. because from my ip on rapidshare already downloading. please mail on cg_ar(a)mail.ru
Click to expand...
Click to collapse
Well, I do realize your frustration,but this application still needs to be tested and tried first,as far as I know,it has not been applied and tried yet.
But keep your fingers crossed as I'm,hope it comes out successful,it wud solve this problem of not allowing to "r2sd all" using mtty in CID locked device.
hmm, there's a flaw in my theory: It's necessary to access WinCE (WM) to allow Haret to do it's job
Maybe there's a work around i can think of...
sorry
cg_ar said:
i download a wzg3.7z. unpack and have
Hard-SPL.nb
JumpSPL.exe
SPL.lnk
spl.nb.
it has in pack 145kb is it alright?
and jumpspl cannot execute and spl.ink too. How this flash?
Click to expand...
Click to collapse
What to do?

HD blocked on 0%

Hello my HD always rest on 0% when I want to flash it !
and always rest on loading... if I want flash with my SD card
If somebody have a solution for me ? ...
what SPL u use?
do0fusz said:
what SPL u use?
Click to expand...
Click to collapse
what is spl ? I think it's v1.14
I try to install pyrana v7 or duty 1.9 but it's same
read everything here and it will answer your questions:
http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone
phil,
you got lucky you didn't brick you're phone..
next time, R E A D U P
effrything is explainend
do0fusz said:
phil,
you got lucky you didn't brick you're phone..
next time, R E A D U P
effrything is explainend
Click to expand...
Click to collapse
Ok but where ?
I try on my other computer under xp but same ...
I try to use spl 2.2 found on link give by mkent_barbados but I don't know how to install it ?
Ok i found i have to use sspl 1.07.Olinex, I've downloaded it but I have the same problem to install it always 0% !?
phil_rouge said:
Ok i found i have to use sspl 1.07.Olinex, I've downloaded it but I have the same problem to install it always 0% !?
Click to expand...
Click to collapse
I try to launch 1.07.olinex manualy and launch hard-spl ruu but same same same 0% nothing else
phil,
pleas read the info..
start at the wiki page.
i would be sorry to see you brick you're phone cause ý don't know what ur doing
do0fusz said:
phil,
pleas read the info..
start at the wiki page.
i would be sorry to see you brick you're phone cause ý don't know what ur doing
Click to expand...
Click to collapse
I've read all the info in wiki page, I've try olinex like it's described but I have always the same result
Before I have flash my phone and all was ok but now I can't flash again...
witch net framework are you running?
http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Flash3
Hi phil,
first, check your PC framework, as do0fusz has suggested.
Second, look at these steps:
Code:
read this if unsure how to install Hard-SPL...
1) download Hard-SPL package from attachment, extract to an empty folder.
2) you must Have Phone Synced with PC in Windows Mobile!!!
3) run HardSPLWrapper_Blackstone.exe on PC, make sure it's launched from a local drive (not through network drive, etc.). if you are on vista, launching as Administrator is recommended,
4) follow steps in the RUU, check device for prompts after PC shows loading bar, press Yes on phone if asked. please answer with Yes as fast as you can!
5) some notes: when RUU says it will hard reset, do not worry, it is not going to do that. also when it says the flash will take 10 minutes, ignore that, it will only take a minute or so.
6) device should go to a tricolour screen now that says 1.07.OliNex, the SSPL version, which is temporary.
7) in a bit unusual way, it will take a few seconds for the RUU to detect the device, but do not worry, as soon as the "USB" text on the tricolour screen shows up, RUU will see device.
8) SPL flashes, device automatically reboots, job done.
9) to confirm you got it installed, go into bootloader mode (tricolour screen!) and verify the screen shows 1.14.OliNex, which is the Hard-SPL version.
Note the point 4, expecially this "please answer with Yes as fast as you can!". When I've flashed HSPL I had the same problem like you, but after reading this carefully, all went in the right way.
Good luck
do0fusz said:
witch net framework are you running?
http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Flash3
Click to expand...
Click to collapse
I try v3.5 sp1 may be this ...
phil_rouge said:
I try v3.5 sp1 may be this ...
Click to expand...
Click to collapse
YOU WILL TRY
u clearly didn't read the wiki..
why don't you help you touch HD a little ?
if you read efferything and understood it properly this won't be a problem.
try copying SSPL-Manual-TouchHD.exe to you phone, execute it.
then try flashing again..
do0fusz said:
YOU WILL TRY
u clearly didn't read the wiki..
why don't you help you touch HD a little ?
if you read efferything and understood it properly this won't be a problem.
try copying SSPL-Manual-TouchHD.exe to you phone, execute it.
then try flashing again..
Click to expand...
Click to collapse
I read all but my english is a little bit bad so i try all i understand
I have try copying SSPL-Manual-TouchHD.exe to you phone, execute it.
then try flashing again it the same thing
I try run flash with my sd card it's same ...
now i'am installing net framework v3.5 ...
without framework v.3.5, it is N O T posible to flash..
sorry, my french is wourse then you're english
do0fusz said:
without framework v.3.5, it is N O T posible to flash..
sorry, my french is wourse then you're english
Click to expand...
Click to collapse
THANK'S I've install framework v3.5 and I can install olinex and now I can flash ! YES
But I don't understand why before I was able to flash on my computer ...
because of the standard v.2.0 effery windows haves..

[TUT] Task 29 (Format internal memory) XPeria X1

Hello, i have searched on xda-developers how to use Task 29 tool, and it's not explained very well, so i am going to explain you how to use it... I would like to thank to agent_47 for his explanation, and link.
We use Task 29 to format phone memory. When we install a lot of ROMs, sometimes new ROM just overwrite old ROM files, not delete them. That cause new ROM to unstability.
(IMPORTANT) Using Task 29, phone memory will be deleted, but it won't delete you SPL and Radio
1. Connect your XPeria X1 to PC in Disk Drive mode.
2. Transfer the custom ROM you want to install on ROOT of memory card and make sure that it's named "kovsimg.nbh"
3. Disconnect phone from USB.
4. (IMPORTANT) DO NOT TURN OFF DEVICE, JUST REMOVE MEMORY CARD!
5. Download the Task 29
(Click here to download Task 29)
6. Extract it to Desktop
7. Connect phone in ActiveSync mode. (wait until installs drivers itself)
8. Now open "task29" folder, and there is 9 items.
9. Run ROMUpdateUtility (Vista/7 Users - right click>Run as Administrator)
10. Follow on screen instructions, and it will start to clean storage. (It says that this process takes up to ten minutes, but it only takes 2,3 minutes top)
11. When the bar comes to 100%, press finish.
12. (IMPORTANT) THE PHONE WILL REBOOT ITSELF AND IT WILL STUCK ON SONY ERICSSON LOGO! But that's okay, because there is no ROM to run, we just cleaned the phone storage.
13. Remove battery and insert memory card. (We put custom ROM on memory card in step 2)
14. Put battery and cover on, and press the volume button down, and power button, and HOLD BOTH BUTTONS UNTIL 3-colored screen shows.
15. That's it, now follow on-screen instructions to install custom ROM, and when done, i strongly reccomend to HARD RESET PHONE.
Hard Reset - Press two buttons below screen (left and right) and hold it, and press the power button UNTIL VIBRATE, then release the power button, BUT STILL HOLD TWO BUTTONS BELLOW THE SCREEN (IMPORTANT)
That's it, i have done it for the first time, and i was looking for explanation like this ( I do not want to brag myself ) So i hope i made you easy this process, and belive me, my phone it really works faster after Task 29.
Also, take a look at my other thread "Installing new custom ROM using phone" in which is explained how to install a custom ROM also step-by-step.
That's a great guide to flashing ROMs! Very straightforward and clear.
Wish it existed when I was flashing a custom ROM for the first time.
It would be nice to have it stickied as it's really very helpfull and informative.
Haplok said:
That's a great guide to flashing ROMs! Very straightforward and clear.
Wish it existed when I was flashing a custom ROM for the first time.
It would be nice to have it stickied as it's really very helpfull and informative.
Click to expand...
Click to collapse
Thank you.
I also flashed first ROM with suffer, because there isn't guides like this one, so i created one
i like your tuturial, too!
good work bro!
freak4all said:
i like your tuturial, too!
good work bro!
Click to expand...
Click to collapse
Thank you very much
Great turtorial!!
Very straightfoward and easy to understand in the steps provided.
This should definately be stickied for novice flashers.
nycdemons said:
Great turtorial!!
Very straightfoward and easy to understand in the steps provided.
This should definately be stickied for novice flashers.
Click to expand...
Click to collapse
Thank you very much
Also, check out new thread "Installing new custom ROM using phone"
milancex said:
Thank you very much
Also, check out new thread "Installing new custom ROM using phone"
Click to expand...
Click to collapse
nice! perhaps you may want to compile that thread into this one though and label it, Tutorial: using task 29 to clear phone memory and install custom. that way, people wont have to check 2 threads
nycdemons said:
nice! perhaps you may want to compile that thread into this one though and label it, Tutorial: using task 29 to clear phone memory and install custom. that way, people wont have to check 2 threads
Click to expand...
Click to collapse
Thanks again! Well, i think it's better this way, there are many steps in this thread, and in the other one, so might be confusing but thank you for interesting but i will put link into this thread for "Installing new custom ROM using phone"
Hi,
nice one. Could have been added to the original thread but maybe it's easier to find like this.
I won't sticky it, as we want to keep as little stickies as possible to keep the forum "tidy", but I will add this to the reference thread.
I also updated the title.
Thx and best, DK
hard reset
to hard reset, the easiest way is to dial *74*# and call button, then it will be asked whether to soft reset or hard reset?... hope it was informative...
susheelnamdeo said:
to hard reset, the easiest way is to dial *74*# and call button, then it will be asked whether to soft reset or hard reset?... hope it was informative...
Click to expand...
Click to collapse
Well, we need to reset phone BEFORE FIRST RUN
I don't think that's actually necessary. But you would be wasting a lot of time to configure the system if you activated the phone before the hard reset (because then you have to configure it again anyways).
Haplok said:
I don't think that's actually necessary. But you would be wasting a lot of time to configure the system if you activated the phone before the hard reset (because then you have to configure it again anyways).
Click to expand...
Click to collapse
Yeah, and hard reset BEFORE first run is strongly reccomended!
Help. I have tried to run task29 but every time the phone gets into bootloader mode I get connection error [260]. My computer then says "USB device not recognized". My HardSPL version is Olinex-0.72. I am using Energy Rom.
naklar said:
Help. I have tried to run task29 but every time the phone gets into bootloader mode I get connection error [260]. My computer then says "USB device not recognized". My HardSPL version is Olinex-0.72. I am using Energy Rom.
Click to expand...
Click to collapse
That happend to me first time also, your driver for ActiveSync (for Vista/7 "Windows Mobile Device Center") are not installed...
If you are Windows XP user download ActiveSync (link below)
ActiveSync
It won't ask for validation, you can download it...
If you are Windows Vista/7 user download Windows Mobile Device Center (link below)
Windows Mobile Device Center
(This link for Windows Mobile Device Center is on Microsoft site, and YOU NEED TO HAVE ORIGINAL WINDOWS INSTALLED, IT WILL ASK YOU FOR VALIDATION KEY! IF YOU DO NOT HAVE ORIGINAL WINDOWS... google for "Windows Mobile Device Center" )
Let us know what have you done...
Greetings
milancex said:
That happend to me first time also, your driver for ActiveSync (for Vista/7 "Windows Mobile Device Center") are not installed...
If you are Windows XP user download ActiveSync (link below)
ActiveSync
It won't ask for validation, you can download it...
If you are Windows Vista/7 user download Windows Mobile Device Center (link below)
Windows Mobile Device Center
(This link for Windows Mobile Device Center is on Microsoft site, and YOU NEED TO HAVE ORIGINAL WINDOWS INSTALLED, IT WILL ASK YOU FOR VALIDATION KEY! IF YOU DO NOT HAVE ORIGINAL WINDOWS... google for "Windows Mobile Device Center" )
Let us know what have you done...
Greetings
Click to expand...
Click to collapse
Thanks for your help milancex. I am running Windows 7 (genuine) and I have reinstalled WMDC. My Xperia is still not recognized in bootloader mode.
I reran the X1_HardSPL.exe and it was able to connect (it probably loads bootloader drivers). It seems that HardSPL uninstalls the bootloader drivers when it finishes running
A check of the properties of the Unknown Device under Device Manager when I connect my X1 in bootloader mode says that windows stopped the device because there was a problem with it.
Any other ideas?
Greetings
naklar said:
Thanks for your help milancex. I am running Windows 7 (genuine) and I have reinstalled WMDC. My Xperia is still not recognized in bootloader mode.
I reran the X1_HardSPL.exe and it was able to connect (it probably loads bootloader drivers). It seems that HardSPL uninstalls the bootloader drivers when it finishes running
A check of the properties of the Unknown Device under Device Manager when I connect my X1 in bootloader mode says that windows stopped the device because there was a problem with it.
Any other ideas?
Greetings
Click to expand...
Click to collapse
first, why did u run x1_hardspl? don't u have hardspl installed?
Nice TUT, thanks...
Oz
ozzybulldog said:
Nice TUT, thanks...
Oz
Click to expand...
Click to collapse
you're welcome

Problem qtek 9090 with upgrading from windows 2003 to windows mobile 6.5

Howdy XDA-deveopers! My name is Adrian and i'm problem is:I want to upgrade the qtek 9090 to windows mobile 6.5 and I tried the Rom Updater Utility and the screwed up bad! The display shows v 2.08 somewhere at the bottom of the screen and write SERIAL! When you connect to your PC via a serial cable instead of writeUSB which leads me to believe that it is in download mode. I don't know what to do! Please help me with this problem to solve!
Waiting for suggestions and questions!
Yours faithfully
:good:
Adrian
ady_90 said:
Howdy XDA-deveopers! My name is Adrian and i'm problem is:I want to upgrade the qtek 9090 to windows mobile 6.5 and I tried the Rom Updater Utility and the screwed up bad! The display shows v 2.08 somewhere at the bottom of the screen and write SERIAL! When you connect to your PC via a serial cable instead of writeUSB which leads me to believe that it is in download mode. I don't know what to do! Please help me with this problem to solve!
Waiting for suggestions and questions!
Yours faithfully
:good:
Adrian
Click to expand...
Click to collapse
LOOK HERE:
http://forum.xda-developers.com/showpost.php?p=5456317&postcount=6
OR
http://forum.xda-developers.com/showthread.php?t=630416
OR
....
The forum is full of guides... Searching is a good start...
Thank you for d-two!
d-two said:
LOOK HERE:
http://forum.xda-developers.com/showpost.php?p=5456317&postcount=6
OR
http://forum.xda-developers.com/showthread.php?t=630416
OR
....
The forum is full of guides... Searching is a good start...
Click to expand...
Click to collapse
Thank you so verry much! All for good!:highfive::good:
Problem installing WM 6.5 x Blue Angel!
d-two said:
LOOK HERE:
http://forum.xda-developers.com/showpost.php?p=5456317&postcount=6
OR
http://forum.xda-developers.com/showthread.php?t=630416
OR
....
The forum is full of guides... Searching is a good start...
Click to expand...
Click to collapse
Hi d-two! All the programs I've recommended you've downloaded earlier and we did nothing to do with them until today when we've executed on a computer with Windows XP I have a laptop with windows 7 Ultimate and I think it was the reason why we did nothing! Today we managed to restart the windows of the old one by updating the RADIO and then i did update to the Blue Angel WM6.5.x x! We managed to enter in the phone and then drove off, then started installing windows! I did format the memory I set English and more than a few moments was restarted and was blocked, would remain the 3 colors on the screen and the bottom corner data about it. it stuck about 2 minutes and i pulled out the battery and I reintroduced it after that I turned on the phone and he remains all at that stage and doing nothing! This you can see in the attached posting. I want to know what can I do in this case! Expect questions and suggestions!
Thanks for that help me and please do it!
Yours faithfully!
Adrian
ady_90 said:
Hi d-two! All the programs I've recommended you've downloaded earlier and we did nothing to do with them until today when we've executed on a computer with Windows XP I have a laptop with windows 7 Ultimate and I think it was the reason why we did nothing! Today we managed to restart the windows of the old one by updating the RADIO and then i did update to the Blue Angel WM6.5.x x! We managed to enter in the phone and then drove off, then started installing windows! I did format the memory I set English and more than a few moments was restarted and was blocked, would remain the 3 colors on the screen and the bottom corner data about it. it stuck about 2 minutes and i pulled out the battery and I reintroduced it after that I turned on the phone and he remains all at that stage and doing nothing! This you can see in the attached posting. I want to know what can I do in this case! Expect questions and suggestions!
Thanks for that help me and please do it!
Yours faithfully!
Adrian
Click to expand...
Click to collapse
ok first please, don't make so big and color full font... this is really ugly for my eyes...
yes, i know this problem turn out the battery for 1 hour and put it back and it will bootup...
ady_90 said:
Hi d-two! All the programs I've recommended you've downloaded earlier and we did nothing to do with them until today when we've executed on a computer with Windows XP I have a laptop with windows 7 Ultimate and I think it was the reason why we did nothing! Today we managed to restart the windows of the old one by updating the RADIO and then i did update to the Blue Angel WM6.5.x x! We managed to enter in the phone and then drove off, then started installing windows! I did format the memory I set English and more than a few moments was restarted and was blocked, would remain the 3 colors on the screen and the bottom corner data about it. it stuck about 2 minutes and i pulled out the battery and I reintroduced it after that I turned on the phone and he remains all at that stage and doing nothing! This you can see in the attached posting. I want to know what can I do in this case! Expect questions and suggestions!
Thanks for that help me and please do it!
Yours faithfully!
Adrian
Click to expand...
Click to collapse
Try MTTY is it does not work. This happened to me.
Thank you for best answer!
TheAH said:
Try MTTY is it does not work. This happened to me.
Click to expand...
Click to collapse
First of all thank you for the reply and I want to tell you that I did what you recommended and so is no longer doing anything! Sometimes it appears R: G: none and none D: WM 6.5 X! Please tell me what do you do with MTTY! Waiting for your answer!
Yours faithfully
Adrian
ady_90 said:
First of all thank you for the reply and I want to tell you that I did what you recommended and so is no longer doing anything! Sometimes it appears R: G: none and none D: WM 6.5 X! Please tell me what do you do with MTTY! Waiting for your answer!
Yours faithfully
Adrian
Click to expand...
Click to collapse
"R: G: none and none" this can resolve with press reset...
Sorry for the late reply. If it says R: None, G: None... Just reset the device. Let me know if it works.
The problem is continue! Help!
TheAH said:
Sorry for the late reply. If it says R: None, G: None... Just reset the device. Let me know if it works.
Click to expand...
Click to collapse
Thank you all for your answers and I know that I did just as you said! After I reset the faut showed figures at R and G but here no longer continue to start the installation! I upgraded the RADIO and software HTC BlueAngel but so is no longer wants to start installing as it did the first time and it was locked! What should I do so I can install the WM 6.5 successfully or to install other software ...? Waiting for your suggestions and questions!
Yours faithfully!
Adrian.
The problem is beeing continue! HELP!
d-two said:
"R: G: none and none" this can resolve with press reset...
Click to expand...
Click to collapse
Thank you all for your answers and I know that I did just as you said! After I reset the faut showed figures at R and G but here no longer continue to start the installation! I upgraded the RADIO and software HTC BlueAngel but so is no longer wants to start installing as it did the first time and it was locked! What should I do so I can install the WM 6.5 successfully or to install other software ...?I check other versions WM 6.5 and not succesfully install on my qtek 9090! Why? Waiting for your suggestions and questions!
Yours faithfully!
Adrian.
ady_90 said:
Thank you all for your answers and I know that I did just as you said! After I reset the faut showed figures at R and G but here no longer continue to start the installation! I upgraded the RADIO and software HTC BlueAngel but so is no longer wants to start installing as it did the first time and it was locked! What should I do so I can install the WM 6.5 successfully or to install other software ...?I check other versions WM 6.5 and not succesfully install on my qtek 9090! Why? Waiting for your suggestions and questions!
Yours faithfully!
Adrian.
Click to expand...
Click to collapse
If you stuck at the 4 color screen put the battery out and wait an hour or two and put it back...
The problem is beeing continue! HELP!
d-two said:
"R: G: none and none" this can resolve with press reset...
Click to expand...
Click to collapse
Thank you for your answers and to know that I did this! I kept battery remover for a day and when I pornut him so I don't want to start installing WM 6.5! Why not go to install it? What still needs to be installed on your phone or what else needs to be done and I do not do? I entered in the boot options by pressing RECORD and perform the reset! Showed some features like ENABLE KITL-NO; CLEAN REGISTRY HIVE-NO; FORMAT STORAGE-NO and YES they make room! What can I do here I mean to put YES and NO to that and then how do I save the settings made? Waiting for your answer and questions!
Yours faithfully!
Adrian.
The problem is SUCCESFUL SOLVED
d-two said:
"R: G: none and none" this can resolve with press reset...
Click to expand...
Click to collapse
Hello! Thank you for all answers that is verry good and we helped my! The problemn is solved because the WM 6.5 is installed on my Qtek 9090! This is pobsible because with MTTY i'm run an commands on the device and we performe reset the PDA! And sudenly the windows installation is begined until the finished! Good bye and we hear in futture! Until then I wish you very good health and all the best!
Yours faithfully!
Adrian

Categories

Resources