Database Develop

Big Problem?

I was performing the radio update on my MDAIII and now he hangs in the bootloader with USB in the upper middle und 2.08 in the under middle. All resets won`t bring it back to life. If I try to reinstall the update all I get is a blank message screen (update from version to version) in my Vista. How can I get out of there.
I did everything what was stated here
The original BAUpgradeUT won`t find my device. The MAUpgradeUt_noID.exe gives me the blank screen with the update from to screen.

Drake008 said:
I was performing the radio update on my MDAIII and now he hangs in the bootloader with USB in the upper middle und 2.08 in the under middle. All resets won`t bring it back to life. If I try to reinstall the update all I get is a blank message screen (update from version to version) in my Vista. How can I get out of there.
I did everything what was stated here
The original BAUpgradeUT won`t find my device. The MAUpgradeUt_noID.exe gives me the blank screen with the update from to screen.
Click to expand...
Click to collapse
I'm using a Vista PC.
After the Radio update to 1.15 the error described above is not to go away yet.
What to do, I'm nearly in tears.

Finally I got it back but with an old Romupdate from T-Online. Is there someone who got the QTC 9090 update (latest one)

That was fast..
im glad you solved your problem.
i think someone here has it.
just post what you need and make it as a title for others to read in the digest.

Im not a expert but is vista the problem??

Most likely.

Failed MDA II flash with vista notebook
Hello everybody,
I just read this thread in hope to find a solution for my problem, which is quite similar to the one described here initially.
I got a used MDA III with T_Mobile ROM. Since I'm a customer with O2, I wanted to change the ROM to O2 as well. I followed the directions given in an other thread here (don't have the link just now) and during the flashing, the flash application suddenly had no connection to my MDA III anymore. It was securely settled in its craddle an connected to my laptop via USB. Now my MDA III is stuck in Bootloader Mode with USB v2.07 displayed on the screen.
Each retry of installing either the O2 or the T_Mobile ROM now meet with the error 101: no connection. I read here that you managed to update successfully with a vista pc. Thus I wanted to ask, how you did that since I just don't seem to find the reason for the connection failing each time.
Here is what i tried to establish connection so far:
* disabled virus scanner & firewall
* unplugged the mda III and plugged it in again. It was recognized as a new device but that didn't help the connection issue
Could you please post what you did to make the update work under vista? Help would be greatly appreciated

mda3newbie said:
Hello everybody,
I just read this thread in hope to find a solution for my problem, which is quite similar to the one described here initially.
I got a used MDA III with T_Mobile ROM. Since I'm a customer with O2, I wanted to change the ROM to O2 as well. I followed the directions given in an other thread here (don't have the link just now) and during the flashing, the flash application suddenly had no connection to my MDA III anymore. It was securely settled in its craddle an connected to my laptop via USB. Now my MDA III is stuck in Bootloader Mode with USB v2.07 displayed on the screen.
Each retry of installing either the O2 or the T_Mobile ROM now meet with the error 101: no connection. I read here that you managed to update successfully with a vista pc. Thus I wanted to ask, how you did that since I just don't seem to find the reason for the connection failing each time.
Here is what i tried to establish connection so far:
* disabled virus scanner & firewall
* unplugged the mda III and plugged it in again. It was recognized as a new device but that didn't help the connection issue
Could you please post what you did to make the update work under vista? Help would be greatly appreciated
Click to expand...
Click to collapse
Try on computer with Windows XP and kill activesynk (wcecomm.exe on taskmanager/processes)
Maybe it will work. If u cant flash O2 ROM try to use "MaUpgradeUt_noID.exe". On my Qtek 9090 allways flash using this APPS and allways work.
U can try too format device first, put it on candle and use "mtty1.42.exe". On XP, kill active sync, and open mtty1.42.exe and select port USB and put OK. Do "Enter" on command and should appear USB>. After this write Task 28. This will format all your PC. Try install SO after this. This command delete all files on PPC. I have attach files that you maybe need.

thankfor the tipp and sorry for my late reply. Since I have no XP PC available i tried the mtty1.42.exe on my vista notebook. When i run it however, it only lists com port 1-3, no usb port. Do i have to make a special configuration on vista for it to work?
Thanks in advance,
mda3newbie

mda3newbie said:
thankfor the tipp and sorry for my late reply. Since I have no XP PC available i tried the mtty1.42.exe on my vista notebook. When i run it however, it only lists com port 1-3, no usb port. Do i have to make a special configuration on vista for it to work?
Thanks in advance,
mda3newbie
Click to expand...
Click to collapse
In vista i dont know...sorry for my late reply too.... in XP u must kill ActiveSync process called wincecom.exe. in vista, maybe u have to kill the Windows Mobile Device Center....i dont know...
Dont forget, put the Qtek 9090 in Boot Loader Mode (Pressing Power Button + Record Button + Reset), maybe will appear USB and u can format the device.
If this does not work, try on Windows XP....Find a friend with Windows XP and ask him to use his PC only to do that.
Maybe somebody in forum have the Windows Vista and can help u....
Sorry my terrible english....

Sjogos said:
Try on computer with Windows XP and kill activesynk (wcecomm.exe on taskmanager/processes)
Maybe it will work. If u cant flash O2 ROM try to use "MaUpgradeUt_noID.exe". On my Qtek 9090 allways flash using this APPS and allways work.
U can try too format device first, put it on candle and use "mtty1.42.exe". On XP, kill active sync, and open mtty1.42.exe and select port USB and put OK. Do "Enter" on command and should appear USB>. After this write Task 28. This will format all your PC. Try install SO after this. This command delete all files on PPC. I have attach files that you maybe need.
Click to expand...
Click to collapse
hi guys I tried the step by step process and when im enterin( Task 28 ) then pressed Enter -
Invalid command : Task28
For a help screen, use command ? or h
does any one know where the problem is??

Try this
Downlaod the XDA IIs .exe file and run it - no need to put into USB mode
http://www.o2online.ie/wps/wcm/conn...es+&+accessories/Xda+Range/Software+upgrades/
this should reset to factory default (o2)
it runs on vista too
I am not 100% sure it will work but worth a try

diesel_dog said:
Im not a expert but is vista the problem??
Click to expand...
Click to collapse
Yes, i know my reply is late but the problem ist 100% Vista! i Tryed 2 ours with vista...then i decided to format my pc and to install XP. At the first try it worked!

D810 w/WM6 upgrading fail, error 260

I've spent whole day reading through the froum and the trinityguides.info site but can't find any proposed solution to work for my situation.
Device info:
ROM version: 3.00.707.17 (WM6)
ROM Date: 6/29/07
Radio version: 1.46.00.11
I've tried using all 3 versions of hard-spl but they all end up with the same result. With active sync linked and ready, ran the "romupdateutility.exe" at the end the PDA prompts if I want to run the "enterbootloader.exe", the moment I press yes the active sync connection would drop and eventually the program timed out with error "260" while PDA stuck in the tri color screen displaying the following:
TRIN100
SPL-1.07.ds
I've found some similar problems in the forum but those users are using vista however I am running XP sp3 in this case. I've tried all other solutions in the FAQ areas but none of them works.
My unit came with the WM6 already but I just want to upgrade the radio and get some cooked ROM to get faster performance. What am I missing here?
Any help is appreciated.

Once it drops to the tri-colour screen and is in bootloader, run the RUU again. Should be all that you need.

I've tried running it over and over but on the bottom it just kept on saying "serial" when it suppose to say USB.
Anyways, problem solved and it turned out to be the cable. For some reason the cable is good for anything, except keeping the phone connected/recognized while in bootloader mode.
I think this should be listed as one of the FAQ in the trinityguide. This might be a rare problem but it surely took me a lot time to figure out.

on Vista
Hi,
I have similar problem but I'm using Vista (Business). Is there any workaround ?
Regards,
Daneal

Hi
I have the same problem
spl 1.20 Olipro display serial instead of usb
I tryed several usb cables and still the same
when trying to update the rom it refuse to connect the ppc and end displayng the 260 error no connection
My system is vista and the first time I upgrade everything was fine, I followed all tutorials and no problem at all.
Do you think that could be this new 6.1 Mobile device center I recent install the cause?
best regards
Inabox

The problem isn't the WMC as such more the fact its Vista. Find an XP PC and do it from there.

Hi there, I had the same problem just now and cured it(in Vista). Just upgrade the htc driver in device manager again with "wceusbsh.inf" previous file, then should be ok. It seem to be Vista replaced the driver during it switched to Tri color menu.....

Stuck on Splash, can't flash another ROM

A while ago I tried to Flash a version of WM6 from mfrazzz on my wizard. The installation seemed to go ok, but when I boot it up i coudn't get past the second splash screen. I thought the phone was a gonner until last night, when I gave it another shot putting on Button ROM. I followed these instructions and it worked. The instructions also had me unlock the phone, and that worked fine too. after that I tried updating my IPL and SPL, Right now my IPL is 1.05 and SPL is 3.08
After this I tried unsuccessfully to get WM6, I think I started off trying Faria.
(So here is the actual problem)
After I tried installing Faria unsuccessfully, I couldn't get Button ROM back up. I'm stuck on the second splash screen (picture of a mug of beer in front of the Colosseum). I've tried flashing my phone w/ everything i've got, including button ROM and Love, and nothing works. most of the WM6 Update Utilities won't even connect. Button Rom connects, stalls at 98%, finished and says it was a success, but I'm still hung up on the Splash.
(I'm running WinXP w/ SP2)
I really just want something running on this phone, don't care what it is.
Thank you for your time

Download official stock rom to recover back and download WST_4.2.2 to verify the CID lock/unlock status,most probably its still CID locked.or you can even reflash 'Button's Rom' again.

No, I've tried to reflash button rom many times. It says it works but it gets hung up on the splash. Since I can't get anything to run on it WST won't work (I think)

Yes! WST only works on a working OS,have you tried to flash the official stock rom ?
Don't activesync or establish partnership,better if you altogether disable & close activesync and end process 'WCESCOMM.EXE' in the Task Manager and try to end as many applications running at the background.Don't surf the net,disable all anti virus and firewall.
Simply get the phone into Bootloaders mode,hook up with pc via usb cable,watch small usb appear at the bottom of Bootloader screen and run the Rom,hope it'll work.

hEY ZABARDAST
zabardast_1 said:
Yes! WST only works on a working OS,have you tried to flash the official stock rom ?
Don't activesync or establish partnership,better if you altogether disable & close activesync and end process 'WCESCOMM.EXE' in the Task Manager and try to end as many applications running at the background.Don't surf the net,disable all anti virus and firewall.
Simply get the phone into Bootloaders mode,hook up with pc via usb cable,watch small usb appear at the bottom of Bootloader screen and run the Rom,hope it'll work.
Click to expand...
Click to collapse
I did this when my Wizard stucks on the splash...
Get mtty 1.04 i thin i dont remember exactly but the higher i ever saw.
kill process wcesscom in PC
conect the ppc on Bootloader
click on conection it shows USB if not... start up again the process
then a white screen appears
I type: task 28
then it works a little on some memory directions
I type: task 28 55aa [or something] (its better get the info on wiki cause it works on chip directly)
without unplug the PDA starts the RUU again...
It works for me...
This is a process for HTC Universal but it works on Blue angel and Wizard for sure!
wait a little i will confirm the steps and the exactly words to type in.

you might need clean the ROM or your flash ROM is overcooked.
I can repair your phone !

+ Que PPC said:
I did this when my Wizard stucks on the splash...
...
wait a little i will confirm the steps and the exactly words to type in.
Click to expand...
Click to collapse
Hey + Que PPC!
Have you confiirmed those values? And is your Wizard CID unlocked?
This would be great to confirm working so that all those with CID locked devices could get their phones back - without paying IMEI-check.co.suckourmoney.uk
@ twig2256
If your phone is CID unlocked try Drugstore's method of recovering Splash Screen frozen phones
cheers

YES
The values are the same for every DOC CHIP
When the MTTY conects to USB type exactly this...
task 28
(then it will work formating and cleaning the DOC
then it says succesfully clean
and now type...
task 28 55aa
it again works on the same process you can close the mtty without unplug your device... update your device with a Stock rom.
Actualy I have issues with mtty i dont know why i can acces to USB it say CMD GOD Damn can anybody helps...
This is the link that mestrini said for drug gsm store metod to unfreeze
http://forum.xda-developers.com/showthread.php?t=276963
Hey mestrini see this...
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader
even if it is universal it work for Wizard i did it once it works for me. but now it wont why????

zabardast_1 said:
Yes! WST only works on a working OS,have you tried to flash the official stock rom ?
Don't activesync or establish partnership,better if you altogether disable & close activesync and end process 'WCESCOMM.EXE' in the Task Manager and try to end as many applications running at the background.Don't surf the net,disable all anti virus and firewall.
Simply get the phone into Bootloaders mode,hook up with pc via usb cable,watch small usb appear at the bottom of Bootloader screen and run the Rom,hope it'll work.
Click to expand...
Click to collapse
can't solve my t-mobile mda

HELP! Can´t Get Stock SPL on my X1

Hello!
Please I need help, i want to send my Xperia back for warranty reasons, but i can not manage to get the Stock Spl back on my Phone.
I have done the same as in the Video turturals from BioVolt
(here:
HTML:
http://forum.xda-developers.com/showthread.php?t=497511
)
I am using My Brothers Laptop, which runs on Windows Vista, because I have a Macbook.
So when I do the Steps on the HardSPL programm and finally there comes the Process bar on the Screen of the Laptop. then my X1 turns off and there comes the green-red-....-Screen, which is normal according to the video turtural. Then the phone goes to grey/white screen and says Loading....
Finally the HardSPL programm pops up an error Page where it says that it cannot connect to the PDA Phone. The Phone keeps showing the loading screen and never stops. So i removed the Battery.
I have the tmobile R1 DE ROM currently on it Because it was the Stock Rom.
Please can anybody tell me What is the Problem and how to Solve it?
Is it maybe because I am trying it with Vista and not with XP?
If yes can anybody tell me how to do it with Vista??
Thanks

lernst_07 said:
Hello!
Please I need help, i want to send my Xperia back for warranty reasons, but i can not manage to get the Stock Spl back on my Phone.
I have done the same as in the Video turturals from BioVolt
(here:
HTML:
http://forum.xda-developers.com/showthread.php?t=497511
)
I am using My Brothers Laptop, which runs on Windows Vista, because I have a Macbook.
So when I do the Steps on the HardSPL programm and finally there comes the Process bar on the Screen of the Laptop. then my X1 turns off and there comes the green-red-....-Screen, which is normal according to the video turtural. Then the phone goes to grey/white screen and says Loading....
Finally the HardSPL programm pops up an error Page where it says that it cannot connect to the PDA Phone. The Phone keeps showing the loading screen and never stops. So i removed the Battery.
I have the tmobile R1 DE ROM currently on it Because it was the Stock Rom.
Please can anybody tell me What is the Problem and how to Solve it?
Is it maybe because I am trying it with Vista and not with XP?
If yes can anybody tell me how to do it with Vista??
Thanks
Click to expand...
Click to collapse
vista is not % 100 compatible with x1.so i ll recommend you to use xp.you ll be allright.because i did in xp without problem.in the vista or mac you can install wmware and you can get virtual xp if you want.you can google for more info about wmware.good luck mate.

I've done it with vista ok:
Tips: Disconnect from internet (Shut down wifi/lan)
Turn of Windows firewall/standalone firewall
Turn off anti-virus software
remove SD card
Try to remove hard spl again
Once finished re-enable all firewall/virus stuff before you go back on the internet

cant start WM6.5

Hi,
im cant find on xda-developers solution for my problem :-(
my WM "X2H_WM6.5_v4.8" cant start. sometimes wizard show number for typing PIN and light off...
so i followed this http://forum.xda-developers.com/showthread.php?t=298613, but no working :-(
i get to bootloader screen IPL and SPL 2.26 , when a connect USB (in bootloader) is displayed USB on screen. i downloaded wizard_love rom (as in tutorial) a i tryed to upload to wizard, but romupdateutility say me, that device is not connect :-((
i have windows 7, flash by VMware workstation, where i have installed XP
can anybody help me pls?
(sorry for my English )