Related
Here is an interesting observation. I have noticed the signal strength (HTC Kaiser branded, with the ATT carrier), for the most part has been averaging 2 to 3 bars. While at a local ATT store, I noticed the Tilt, 2 display models, were both displaying 4 bars, while mine, (HTC) branded only gave 2 bars. Now add another customer that also had a branded HTC Kaiser, his displayed the same as mine. Yet both ATT Tilts were (4) bars. The rep. indicted that all the ATT Tilts have been tweaked!. I called HTC and they had no clue. Has anyone been aware of this difference?
more bars in more places...even if it's only imaginary.
is the radio software reporting as the same?
Kaiser signal strength seems OK
Signal strength can also depend on what cell your phone is locked onto at the time. If the nearest cell is busy, your phone could be switched to a less busy nearby cell and thereby show less bars. My own observations are that the Kaiser (I have HTC TyTN II) is every bit as good as my previous Dopod 810 (Trinity) and my friends dedicated LG phone. Signal strength is not an issue for me and I spend every weekend in a very marginal area.
Actually I have noticed the same. On my unbranded HTC Tytn II I also only get 2 bars when the band is set to Auto under phone settings. Selecting network type GSM thus forcing off 3G I can get back to 4 bars so maybe the radio rom for the At&T is better?
On my Tilt I've gone back and forth between the ATT and HTC ROMs and I do get about one bar better on the ATT ROM average.
Well thank you all for the posts. I tried switching the system from auto to GSM, and there you go......full 4 bars. Maybe the Auto 3G limits the signal strength.
Hi
Well thank you all for the posts. I tried switching the system from auto to GSM, and there you go......full 4 bars. Maybe the Auto 3G limits the signal strength.
Click to expand...
Click to collapse
3G doesn't have as good as coverage as GSM, and may even be coming from a different mast to your GSM signal. 3G normally uses higher frequencies that will not penetrate so far into buildings and is transmitted at a lower power.
It is quite common that you will have a lower 3G signal than you would on GSM.
Regards
Phil
Signal Strength.
Hi Thanks for all the posts. I went to settings and phone and cannot see where to change the auto to gsm. I have the new ATT tilt. Help I really need a better signal or I will have to take my wonderful new toy back
dot
Whether you have one or five bars is unimportant. What's important:
Are your calls getting to you or going out with acceptable consistency?
Are you getting the data connection and speeds you desire?
Are able to get the messages you want?
Are you getting the battery life you're looking for?
Answer those questions and then decide whether or not to take the phone back. If it's "yes" to all of the above, then you really don't care if it shows 1/2 a bar - it's meeting the needs you've got.
Signal Strength.
Most everything is great except: When I place or receive a call, most of the time we cannot communicate. Everything cuts out. It is frustrating for me and whomever I am speaking with. I would love to change the settings to GSM only, but I don't seem to have that option on my att tilt 8925.
Signal Strength Fixed AT&T Tilt
Signal Strength Fixed AT&T Tilt
http://www.commmgrpro.com/jsp/main_frame.jsf
switch to Bandswitch tab from CommMgrPRO
download bandswitch zip file unzip should give you cab file.
install it in your TILT, run the program, change AUTO TO GSM
i used to have 2 bars NOW I HAVE 4 FULL BARS
Merry Christmas and Happy Holidays!!!!!!!!!!!!!!!!!11
jimzeeem said:
Signal Strength Fixed AT&T Tilt
http://www.commmgrpro.com/jsp/main_frame.jsf
switch to Bandswitch tab from CommMgrPRO
download bandswitch zip file unzip should give you cab file.
install it in your TILT, run the program, change AUTO TO GSM
i used to have 2 bars NOW I HAVE 4 FULL BARS
Merry Christmas and Happy Holidays!!!!!!!!!!!!!!!!!11
Click to expand...
Click to collapse
Hi:
Sorry if this is a dumb question, but does this also disable 3G/hsdpa?
Thanks and MERRY CHRISTMAS to you too
fredm said:
Here is an interesting observation. I have noticed the signal strength (HTC Kaiser branded, with the ATT carrier), for the most part has been averaging 2 to 3 bars. While at a local ATT store, I noticed the Tilt, 2 display models, were both displaying 4 bars, while mine, (HTC) branded only gave 2 bars. Now add another customer that also had a branded HTC Kaiser, his displayed the same as mine. Yet both ATT Tilts were (4) bars. The rep. indicted that all the ATT Tilts have been tweaked!. I called HTC and they had no clue. Has anyone been aware of this difference?
Click to expand...
Click to collapse
yep i have htc kaiser, same probelm, tried o2 simcard 2 bars same with 3g.Rang htc helpdesk they dont have a clue.many user generally one the net has this probelm.dont know what the fix is.
debu11 said:
yep i have htc kaiser, same probelm, tried o2 simcard 2 bars same with 3g.Rang htc helpdesk they dont have a clue.many user generally one the net has this probelm.dont know what the fix is.
Click to expand...
Click to collapse
I too have tried 2 different SIM cards. I have also tried turning off 3G. Motorola V3xx shows 4 bars of service, while the Tilt (sitting in the same exact spot, at the same time), shows at most 2 bars, and sometimes even 0 bars.
My Treo 750 also always shows at least 2 bars, when the Tilt goes down to zero.
Very frustrating
cincy1020 said:
Hi:
Sorry if this is a dumb question, but does this also disable 3G/hsdpa?
Thanks and MERRY CHRISTMAS to you too
Click to expand...
Click to collapse
I installed this, and before i had it i aways got hspda, now w/it intstalled i only get 3g, i still have hspda enabled via kaiser tweak, but it doesn't show up, i'm in a hspda city(st. louis) i've had it for about a month or so now and cant get it w/this program installed, any fix for this? on the upside i do get more signal strength w/it. I"m using att tilt w/the tilt rom.
tag for increasing signal strength program
In the Kaiser Upgrading forum I added my two cents about this in the Radios thread:
http://forum.xda-developers.com/showpost.php?p=1783489&postcount=96
It's been my experience that 3G/HSDPA has much better throughput than EDGE at a lower signal strength. "2 bars" of 3G reception still beats even "4 bars" of EVDO/EDGE.
Of course, if you want I could tweak the radio .dll to report 4 bars if it will make you feel better -- It's still 2 bars of 3G though. To use a much less flattering analogy it's the equivalent of me peeing on your back and telling you it's raining.
rob.ocelot said:
In the Kaiser Upgrading forum I added my two cents about this in the Radios thread:
http://forum.xda-developers.com/showpost.php?p=1783489&postcount=96
It's been my experience that 3G/HSDPA has much better throughput than EDGE at a lower signal strength. "2 bars" of 3G reception still beats even "4 bars" of EVDO/EDGE.
Of course, if you want I could tweak the radio .dll to report 4 bars if it will make you feel better -- It's still 2 bars of 3G though. To use a much less flattering analogy it's the equivalent of me peeing on your back and telling you it's raining.
Click to expand...
Click to collapse
I think the actual problem isn't that not enough bars are shown, I think the problem (at least for me) is terrible reception. At times, my phone goes down to zero bars, and sends all calls to voicemail. During this exact time, I can have a Moto V3xx and a Treo 750 sitting right next to the Tilt, and both will have at least 2 bars, and good call quality.
PS: My reception seems about the same with 3G on or off. Although I have seen many reports of 3G interfering with reception (ie. when it switches over), in my case turning 3G off completely hasn't helped at all.
HTC Kaiser/TytnII/Tilt Reception sucks!
I had an Mpx220 up until October 2007, which is when I purchased the AT&T Tilt. The VOICE reception on this phone is terrible! I get very low reception at home when I used to get full reception on my Mpx220 before! Also, whenever I'm on the speakerphone, the person on the other line has trouble hearing me. I called AT&T and had them exchange my bad phone. Once I got the new phone... THE SAME PROBLEMS!!!! I went back to my Mpx220 and the reception was wonderful on my Mpx! What's up with the Tilt? Also, the camera has a high resolution, but it takes about 5-6 seconds to take the picture once the button is pressed. Oh, and whenever I lose reception/signal completely and go back to an area where there is good signal, the phone will take FOREVER to recognize it's on a new signal area! Sometimes it doesn't even recognize this and I have to restart the phone. It sucks! This phone, so far, has been good in EVERYTHING except as a phone!!! BEWARE!
Hello all,
I've noticed that with my Kaiser signal usually is very low, no more than two stands... otherwise with all my old phone, for example in my home, signal was full, also with htc touch dual of my friend.
Maybe can be usefull a radio update?
Thanks
Stefano
it could be displaying the 3G signal vs the gprs signal of your old phone...
try turning off 3G
itarix said:
it could be displaying the 3G signal vs the gprs signal of your old phone...
try turning off 3G
Click to expand...
Click to collapse
Old phone was 3G and my operators supports 3G only...
Ste
My Tilt doesn't get very good reception either. When sitting next to a Motorola Razr V3xx (my Mom's phone), the Razr consistently has at least 2 bars, often 3 or 4 when in my house, but the Tilt has, at most 2 bars, and sometimes even loses signal completely. That never happens on the Motorola, but mine often goes straight to voicemail due to lack of signal.
Now, I realize a Razr and a Tilt are apples and oranges , but they are both 3G, so I would think signal should be comparable. Also, this is not a mattar of one phone simply displaying more bars, but of actual call quality.
I thought it may be a defect in my particular phone, but I have since done a warranty replacement for another issue, and was sent out a new one (it wasn't even a refurb). The new one has the same poor reception.
The Tilt is obviously a superior phone to a Razr in most ways. An ideas why call strength is so poor?
PS: I had a Treo 750 prior to the Tilt, and it too had good reception when in the exact same spot as the Tilt.
Hello I bought the Diamond yesterday, I'm very satisfied except for the UMTS signal.
I already have a Touch Cruise (it didn't work in UMTS so HTC repaired it on warranty and now it works like a charm).
In the last 48 hours I had Diamond and Cruise one next to the other, and Diamond has always 2 lines less:
* when Cruise is in HSDPA with 4 lines, Diamond is in HSDPA with 2 lines
* when Cruise is in HSDPA with 2 lines, Diamond is in GSM.
Is this normal?
Many thanks in advance.
J.
Everyone has it i have also a TC and indeed, its shows always 2 lines more then the TD.
Same here my htc diamond has always two lines less than my htc kaiser.
The diamond has really a poor UMTS signal reception. I hope they will be able to boost it with a new ROM.
Same here
before with TC i got 2 lines 3G now non
Thanks for your feedback!
So it seems to be a common problem.
Today I checked during all the day, moving from a city to another city, half the time the Cruise had more lines, half the time they had the same.
Other feedbacks? Thanks
same problem here in austria. before i had full signal with my sony erricson t650i, now with the touch diamond i only have the half signal strength...
Well, it doesnt give many bars, but it works like hell here.
When using it as a modem (I often do on the road) I get speeds upto 150kb/s for browsing and emailing and that is just perfect for everything.
My 3G Reception is also VERY Bad.....
I´m using the latest Radio ROM 1.00.25.03.
Because of this weak 3G Recepion the Diamond changes to GSM very often, this eats the Battery up in about 6-8 Hours.....Even if I don´t play around much and the 3G Coverage here is excellent.....
Diamond: 1-2 Bars
Nokia E51: Always full Bars (-87dBm and up)
Hopefully Reception will be better with a new Radio ROM.
If it´s an Antenna issue.........DAMN!!!
I never had a Mobile with THAT bad 3G Reception.
BtW: GSM Reception is fair to good.... could be better also....
Poor 3G signal
That's right,
I have also very poor 3g signal, even though I live in the city area. I have also missed incoming/outgoing calls because the poor 3G signal.
That's not nice
same prob here (big city)
switched manually to gsm not to loose calls
Are you sure this is just 3G and not worse reception in general (ie due to smaller antenna in Diamond)?
in gsm mode i never experienced any trouble with calls.
in auto mode diamond switches to 3g (half signal strength), but one can't call me
wcg-tom said:
in auto mode diamond switches to 3G (half signal strength), but one can't call me
Click to expand...
Click to collapse
Uh, this sounds even worse. Having a bad reception is one thing but showing a "fake reception" is a complete different level of bug.
Just to ensure that I did not get you wrong: You see a 3G reception (e.g. 2 or 3 bars) but the phone does not receive incoming calls and the caller is redirected to your mailbox instead?
foo said:
Uh, this sounds even worse. Having a bad reception is one thing but showing a "fake reception" is a complete different level of bug.
Just to ensure that I did not get you wrong: You see a 3G reception (e.g. 2 or 3 bars) but the phone does not receive incoming calls and the caller is redirected to your mailbox instead?
Click to expand...
Click to collapse
yes, got me right.
in my case it's not the mailbox, just a message ("not available" or something like that) because of my settings, but that's petty.
thats why i manually switched to gsm. for using 3g (internet) i have to swith this back again.
annoying!
wcg-tom said:
in gsm mode i never experienced any trouble with calls.
in auto mode diamond switches to 3g (half signal strength), but one can't call me
Click to expand...
Click to collapse
This should not happen, even when I have the minimum bars in 3G or H others can call me.
When you have full bars in 3G does it work?
same here, although i found that switching off umts and just using plain 3g solved the issues.
jwalker said:
This should not happen, even when I have the minimum bars in 3G or H others can call me.
When you have full bars in 3G does it work?
Click to expand...
Click to collapse
yes. when it's stable at full bars or even H, i can use it.
but i deacivated 3g anyway because of powersaving. only using it for web access.
there's a tool for switching 3g in comm manager easily, now i'm happy so far.
So, is it phone or is it just peace of s***?
Hi All
Do you have any fresh idea could it(lousy 3g signal) be hardware or software related issue?
The globe is full of small 3g phones without that kind of problem. That's why I really hope this issue could be fixed with the new ROM radio version...???
I hope I'm right, because if the pain is hardware related, we all have bought pretty expencive peace of crap -not the phone. It is not acceptable if the incoming / outgoing calls are missed!
Same problem, poor 3G reception .
Cruise was far better for receiving 3G signal.
Hope it is software only....
For comparison sake I have an old stock razr v3xx and I get FULL service in my room with it.
On my at&t tilt, I get 1-2 bars.
Im running Slueth 3.0 (WM6.1) and I've tried different combinations of HardSPL's and Radios but each one gives me problems that I can not fix. (i.e. - some SPL's have certain bugs where i get a text and it vibrates until i change the ringer to silent, and any other radio than the stock slueth (1.64.08.21 - which I need a link to if anyone can find?) makes my camera not work and I get a black screen.
One thing Ive noticed is on my razr, the band always says 3G. On my tilt, it says "H" - which Ive never seen before. What is "H" - and could this be the reason for poor service?
Again, if anyone knows where I could find Radio 1.64.08.21, and the disable xt9 cab I would greatly appreciate it. (I have searched for both but to no avail for a working link)
H is for hsdpa its just a nother type of service, gprs hsdpa 3g are the main in the US.
No "h" it isn't the problem.
try the ultimate radio thread for the radio you are looking for.
yeah i did, 1.64.08.21 isnt in there
can I force my tilt to choose 3G? My razr picks up 3G with full service yet the tilt uses H with hardly any
I have really awful service too. It loses connection from 3G every 10-30 seconds sometimes, but other times it can sit connected to the 3G.
Sometimes it won't even connect to 3G, then when I soft reset, it connects at 2 bars. Right now it's sitting connected at 3 bars.
What's up with this, and is there any way to improve it? The nearest base station is only 2-3 miles away.
I'd recommend trying out different radios.
Also H stands for HSDPA which is considered to be 3.5g but it actually is 9x faster then 3g.
jay487, search harder.. i found the disable xt9 cab in one search for "xt9". as for the radio your looking for, check out the wiki.
if you change the band to GSM in the band tab in the phone settings the signal will get better if you turn off WCDMA which is 3G or HSDPA, if you don't use 3g for internet then turn it off it will help
yeah I changed the band to GSM out of curiosity and it definitely seems to help so far. I dont use 3G for internet just for picture messaging, this shouldnt be affected correct? I also just did a complete reload of Sleuth to resolve the radio issue.
One problem I still notice on occasion is my sounds will just stop working. If i get a text the sound doesnt play, and if i set it to vibrate when i get a text too sometimes it constantly vibrates until i change the sound to silent and then back. I can fix it with a soft reset but having to do this everyday is anoying.
Do you need a specific program or app to disable 3g or hsdpa? i have the exact same problems, ATT +tilt= bad recep and lots of dropped calls
thanks
tone
I've flashed my phone countless of times now over the past months and one thing I was hoping for would be better signal strenght for WCDMA mode... I live in Switzerland and my provider is sunrise. Whenever I'm using WCDMA mode the signal is just horrible. Mostly 1 bar or sometimes dropping to zero. 3g and H works most of the time, but the signal is bothering me.. I've tried different modems etc.. but nothing seems to change.. Does anyone else have this problem?? what can I do about it? GSM has full bars most of the time and that's why it's so weird.
also worthy to note is that people hear an echo sometimes when they're talking to me both in GSM and WCDMA mode.
it would be great if someone knows how to solve this problem...
have you been on your providers website to check the coverage in your area ? they could be a fault on their part affecting your signal strength
Im on Vodafone UK and i have terrible 3g signal, I can only use 2g/GSM otherwise my phone doesnt recieve 1 bar of signal - bit of a bummer when you have a smart phone and unlimited internet
Finally, How was your signal before you flashed ? when the phone popped out of the box ? was it still poor then ?