Database Develop

Forcing Bootloader Mode

Maybe some of you are already aware of this procedure, maybe not.
Anyway, it worked for me and I decided to share how to do it. Simple.
This procedure should only be used in case you really need enter into a bootloader mode and all other ways to do it has failed! Hold Camera button is one of these I am mentioning.
My Wizard was almost bricked at that time and after I speak with an I-mate technical guy, I got the following:
1. Make sure your i-mate™ K-JAM is not Connected to the PC and remove the dummy card or SD/MMC card
2. On your Desktop PC, open Microsoft ActiveSync, then go to File >Connection Settings >Remove the Selection from “Allow USB Connection with this desktop computer”
3. Reconnect your i-mate K-JAM to the Desktop PC using the USB Cradle and the Charger MUST be Connected to the Cradle (Don’t use the IrDA or Bluetooth for the Upgrade)
4. Run the Upgrade again and it will work fine without any problems.
While upgrading, the ActiveSync program will not go on, however the upgrade is running.
Hope it helps!

this realy worked for my (ex)bricked dutch tmobile mda vario !!!!
tip: REALY make shure that there is no wcescomm.exe running all the time and realy remove the sd card else is nogo
btw: my wizard is CID locked! and works like a charm

Thanks buddy!
I'm happy that worked for ya!
Take care!

I'm having a problem
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Any ideas?

Hi!
Have you already flashed your device once?
Which ipl/spl do you have?
I had problems over 1.05 ROM in the beggining.
If you stuck on bootloader mode, that's a good signal your device is not bricked.
I'd recommend you to disable activesync as you did and reflash it again! Check also if your device is CID unlocked! Search for a thread in the xda developers root.
Try to upgrade to ipl/spl 2.26 first and later to others you want.
Regarding the old file error...can be related to a missing file called enterbootloader.exe.
Hope it works for ya!
Take care
Ironman273 said:
I'm having a problem
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Any ideas?
Click to expand...
Click to collapse

My device is unlocked as I've been trying different ROMs as of late. I had gone back to the Cingular 2.25 ROM for a couple days to sort some things out and was going to flash Farias AKu 3.3 when my power problems happened. My Current IPL/SPL is 2.25
I've tried flashing the TMobile 2.26 but keep getting connection errors. In fact, I've tried flashing with every ROM I have pdviet 3 and 4, CIngular 2.25, TMobile 2.26 and Custom 1.05. Everything (except twice in the custom) gives me connection errors.
Any other trick I can try?
BTW, I used to live in Sao Paulo years ago...
Edit: OK, so I tried the 2.26 TMobile ROM after I typed this and it worked!! I'm back up but I was having trouble with that ROM beause of some incompatibilities with Cingular. I'll go back to Cingular's ROM and play it safe for now.
I believe part of my problem was I kept trying different updates one after the other. Now that I think back, the 2 times I got the update to almost work was after I turned off the device and turned it on again, which is what I did this time around also.

I had the same problems as mentioned by Ironman before. I followed the steps and with a few slight changes, I managed as well to "unbrick" my wiz. THANKS A LOT for the great step by step manual!!!
Still I wanted to know WHY i bricked my device:
I was trying to upgrade to the underground WM6 ROM. I got the same situation as ironman:
Quote:
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Unquote
I then followed the instructions by epimazzo as written above. I also tried the T-Mobile ROM 2.26 which was not working for me. PANIC!!!! Error messag was that I had the wrong Vendor ID. THerefore no upgrade to TMob 2.26 was possible. I tried it then my original qtek ROM in my language and see it worked!!! This IMHO means that I did not put the device in a proper IPL1.xx and SPL 1.xx status which is required for a clean system in irder to unlock it! So if it is bricked, try your native AKU2 ROM and make sure you unlocked it properly. Maybe you have to run the 1.05 ROM for a second time after the unlocking.
I hope this helps you guys.

Sounds great to hear that!
I had play around with pdaviet3, underground and another ROM just today without any problems at all. I don't think that this is the case. Now you get your device back to normal, try to reflash it again. Hope it works this time!
BTW,...São Paulo is a nice city. Thanks! Let me know if you decide to come here!
Take care
Ironman273 said:
My device is unlocked as I've been trying different ROMs as of late. I had gone back to the Cingular 2.25 ROM for a couple days to sort some things out and was going to flash Farias AKu 3.3 when my power problems happened. My Current IPL/SPL is 2.25
I've tried flashing the TMobile 2.26 but keep getting connection errors. In fact, I've tried flashing with every ROM I have pdviet 3 and 4, CIngular 2.25, TMobile 2.26 and Custom 1.05. Everything (except twice in the custom) gives me connection errors.
Any other trick I can try?
BTW, I used to live in Sao Paulo years ago...
Edit: OK, so I tried the 2.26 TMobile ROM after I typed this and it worked!! I'm back up but I was having trouble with that ROM beause of some incompatibilities with Cingular. I'll go back to Cingular's ROM and play it safe for now.
I believe part of my problem was I kept trying different updates one after the other. Now that I think back, the 2 times I got the update to almost work was after I turned off the device and turned it on again, which is what I did this time around also.
Click to expand...
Click to collapse

It seems you got the idea!
You did the right thing! Sometimes, use the official ROM can solve many issues out there!
Keep walking!
enlite_de said:
I had the same problems as mentioned by Ironman before. I followed the steps and with a few slight changes, I managed as well to "unbrick" my wiz. THANKS A LOT for the great step by step manual!!!
Still I wanted to know WHY i bricked my device:
I was trying to upgrade to the underground WM6 ROM. I got the same situation as ironman:
Quote:
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Unquote
I then followed the instructions by epimazzo as written above. I also tried the T-Mobile ROM 2.26 which was not working for me. PANIC!!!! Error messag was that I had the wrong Vendor ID. THerefore no upgrade to TMob 2.26 was possible. I tried it then my original qtek ROM in my language and see it worked!!! This IMHO means that I did not put the device in a proper IPL1.xx and SPL 1.xx status which is required for a clean system in irder to unlock it! So if it is bricked, try your native AKU2 ROM and make sure you unlocked it properly. Maybe you have to run the 1.05 ROM for a second time after the unlocking.
I hope this helps you guys.
Click to expand...
Click to collapse

Excellent post. I messed up with my own cooked ROM and could only get the bootloader screen. Tried the tips here - didn't work first time but I pulled the battery from the KJAM to reset it rather than using the reset button and it worked fine.

In my opinion this thread is so helpful to people who brick their device, it should go "sticky". Mods anything you can do about it?

Thanks buddy! I really appreciate!
We survive here over tips like that!
jt_armstrong said:
Excellent post. I messed up with my own cooked ROM and could only get the bootloader screen. Tried the tips here - didn't work first time but I pulled the battery from the KJAM to reset it rather than using the reset button and it worked fine.
Click to expand...
Click to collapse

Help me similar problem
I upgraded Super Rom, then my Wizard run very slow and no signal (no call out and in- no network at all). And Terible thing is PC could not dectect PPC thought Active Sync. I've soft and hard reset but no use.
So I donot know where to start to re install Rom again.
Please help me....

Hi there!
It seems that you just need to enter into the bootloader mode and reflash it again!
I had similar problems and more during my brick "false" stage!
So, just try to follow my steps here and you should be fine! Once you get into bootloader mode, just use any ROM out there to reflash.
Good [email protected]
thaiphong said:
I upgraded Super Rom, then my Wizard run very slow and no signal (no call out and in- no network at all). And Terible thing is PC could not dectect PPC thought Active Sync. I've soft and hard reset but no use.
So I donot know where to start to re install Rom again.
Please help me....
Click to expand...
Click to collapse

I was about to start a EMERGENCY HELP thread, but I *think* this is the right place instead.
The "touch" of my screen went dead today. It got progressively worse over a few hours, starting with difficulty in using the phone dialer, then random incorrect stuff getting triggered by screen taps.
So I hard reset, and got no response on the fifth alignment cross, meaning 1) "Tap on the screen...; 2) center; 3) top left; 4) bottom left; 5) bottom right. In that I could not proceed with alignment, I hard reset again, and now, at the first alignment screen, i.e. "Tap on the screen...", I have no screen response at all.
I called T-mo, and they are being great about sending a replacement ASAP (and getting me a loaner in the meantime).
BUT, I am running Faria+ AKU3.3 V2... so I clearly have to flash back to T-mo 2.26. I can;t figure out how to do it though, as no matter what I do I am stuck at the first alignment screen!!
HELP!! EMERGENCY!!!
(I have three or four days to get this done, so it's not THAT urgent)

Do a search for Broken Screen. Someone (either in Wizard Upgrading or in the Wizard forum) just had a similar issue with a cracked screen. They downloaded something that allowed them to get around the welcome page.

Actually, if you are just trying to flash a new ROM, don't even mess with it. Go straight to the Boot Loader screen (see the first post of this thread). No tapping necessary until the new rom is on (and that will be the Tmobile then so you would be good.

Thanks for the quick reply. Charging up to green now, and then will try to enter bootloader and flash T-mo 2.26. Will report back.

Worked great. Back to T-mo she goes!!!

BootLoader Mode
Excellent thread but you left out one thing.....exactly how to place your device in bootloader mode.
To clear up any misunderstanding because this is very important....this is how you do it:
Perform a soft reset, when the screen goes blank hold the camera button until a multi colored screen comes up .... That's it !!!!!!
When the unit is connected, USB is displayed at the bottom left.

How to Flash in BootLoader

I have a stuck image on my 8125. The phone "boots" but only shows a white screen, and is unusable.
The "a2sd all" restore option mentioned in the forums doesnt work for me. I have read on several forums that I should be able to reflash the OS from the bootloader, though I cant find any instructions on how to do this
Could someone point me in the right direction for how to flash an OS VIA bootloader?
Thx

1. Get the phone to bootloader (tree color mode) - I think by soft resetting and pressing the camera button at the same time
2. Connect it to the computer (Windows XP) with a USB cable
3. You will notice "USB" written in a lower corner of the phone (this means it is connected)
4. Now you can flash your provider's ROM without any problems
I am not sure whether the bootloader flashing is possible from Windows Vista.
You must flash normally (in bootloader you cannot use either shelltools or SoftSPL - so use your provider's ROM).
Mirek

Mirek - not to be totally ignorant, but the step 4 is what I'm having problems with .... where can I find either a providers ROM, or something that I can actually use while in bootloader mode?
Thanks!

NM ... Found it!
For anyone reading this .... You can get the provider ROM for the 8125 from HTCAmerica here: http://www.htcamerica.net/support/8125/software-downloads.html
Thanks for your help!

mirekluza said:
1. Get the phone to bootloader (tree color mode) - I think by soft resetting and pressing the camera button at the same time
2. Connect it to the computer (Windows XP) with a USB cable
3. You will notice "USB" written in a lower corner of the phone (this means it is connected)
4. Now you can flash your provider's ROM without any problems
I am not sure whether the bootloader flashing is possible from Windows Vista.
You must flash normally (in bootloader you cannot use either shelltools or SoftSPL - so use your provider's ROM).
Mirek
Click to expand...
Click to collapse
Dear Readers,
I'm having problem with my Dopod 900(,Qtek 9000,HTC Universal,O2 Xda Exec,Jasjar ). Can somebody please tell me what to do?
Before this, every time somebody called, the PDA lost the network bar and start to search or network and reject the calls automatically and also i wasn't able to send SMS. Now, i tried to install WM6 crossbow, the phone even cannot be on !!! even when i connect it to the charger, even the light will not be on. the only page that i can see is a white page asks Press 0 to Restore factory default or press X to exit. either perss 0 or X, the phone will be off and i cant turn it on with power key....
Please tell me what can i do ?? I really need your help.
PLEASE REPLY, PLEASE.
[email protected]
Warm Regards to All
G-Jorji

brick?
hey guys, i need a little help. i downgraded my phone to buttons rom and then i was gonna attempt to upgrade the ipl/slp to 2.xx. so i downloaded the wizard ipl/spl 208 from the ftp site. i had a successful flash but when it went to reboot, my wizard never turn on again. ive searched the forums but it seems to me i have a brick found nothing. has anyone had the same situation happen to them? and find a solution?
it wont turn on at all anymore

acuraholic said:
hey guys, i need a little help. i downgraded my phone to buttons rom and then i was gonna attempt to upgrade the ipl/slp to 2.xx. so i downloaded the wizard ipl/spl 208 from the ftp site. i had a successful flash but when it went to reboot, my wizard never turn on again. ive searched the forums but it seems to me i have a brick found nothing. has anyone had the same situation happen to them? and find a solution?
it wont turn on at all anymore
Click to expand...
Click to collapse
WHAT did you downgrade from?
Did you re-unlock your G3?
How's your battery?

acuraholic said:
hey guys, i need a little help. i downgraded my phone to buttons rom and then i was gonna attempt to upgrade the ipl/slp to 2.xx. so i downloaded the wizard ipl/spl 208 from the ftp site. i had a successful flash but when it went to reboot, my wizard never turn on again. ive searched the forums but it seems to me i have a brick found nothing. has anyone had the same situation happen to them? and find a solution?
it wont turn on at all anymore
Click to expand...
Click to collapse
IPL/SPL 2.08? Does that exist? Do you mean 3.08?
Are you sure your device is a G3? Or you killed it when flashing Button's ROM?

Stuck on Splash, can't flash another ROM

A while ago I tried to Flash a version of WM6 from mfrazzz on my wizard. The installation seemed to go ok, but when I boot it up i coudn't get past the second splash screen. I thought the phone was a gonner until last night, when I gave it another shot putting on Button ROM. I followed these instructions and it worked. The instructions also had me unlock the phone, and that worked fine too. after that I tried updating my IPL and SPL, Right now my IPL is 1.05 and SPL is 3.08
After this I tried unsuccessfully to get WM6, I think I started off trying Faria.
(So here is the actual problem)
After I tried installing Faria unsuccessfully, I couldn't get Button ROM back up. I'm stuck on the second splash screen (picture of a mug of beer in front of the Colosseum). I've tried flashing my phone w/ everything i've got, including button ROM and Love, and nothing works. most of the WM6 Update Utilities won't even connect. Button Rom connects, stalls at 98%, finished and says it was a success, but I'm still hung up on the Splash.
(I'm running WinXP w/ SP2)
I really just want something running on this phone, don't care what it is.
Thank you for your time

Download official stock rom to recover back and download WST_4.2.2 to verify the CID lock/unlock status,most probably its still CID locked.or you can even reflash 'Button's Rom' again.

No, I've tried to reflash button rom many times. It says it works but it gets hung up on the splash. Since I can't get anything to run on it WST won't work (I think)

Yes! WST only works on a working OS,have you tried to flash the official stock rom ?
Don't activesync or establish partnership,better if you altogether disable & close activesync and end process 'WCESCOMM.EXE' in the Task Manager and try to end as many applications running at the background.Don't surf the net,disable all anti virus and firewall.
Simply get the phone into Bootloaders mode,hook up with pc via usb cable,watch small usb appear at the bottom of Bootloader screen and run the Rom,hope it'll work.

hEY ZABARDAST
zabardast_1 said:
Yes! WST only works on a working OS,have you tried to flash the official stock rom ?
Don't activesync or establish partnership,better if you altogether disable & close activesync and end process 'WCESCOMM.EXE' in the Task Manager and try to end as many applications running at the background.Don't surf the net,disable all anti virus and firewall.
Simply get the phone into Bootloaders mode,hook up with pc via usb cable,watch small usb appear at the bottom of Bootloader screen and run the Rom,hope it'll work.
Click to expand...
Click to collapse
I did this when my Wizard stucks on the splash...
Get mtty 1.04 i thin i dont remember exactly but the higher i ever saw.
kill process wcesscom in PC
conect the ppc on Bootloader
click on conection it shows USB if not... start up again the process
then a white screen appears
I type: task 28
then it works a little on some memory directions
I type: task 28 55aa [or something] (its better get the info on wiki cause it works on chip directly)
without unplug the PDA starts the RUU again...
It works for me...
This is a process for HTC Universal but it works on Blue angel and Wizard for sure!
wait a little i will confirm the steps and the exactly words to type in.

you might need clean the ROM or your flash ROM is overcooked.
I can repair your phone !

+ Que PPC said:
I did this when my Wizard stucks on the splash...
...
wait a little i will confirm the steps and the exactly words to type in.
Click to expand...
Click to collapse
Hey + Que PPC!
Have you confiirmed those values? And is your Wizard CID unlocked?
This would be great to confirm working so that all those with CID locked devices could get their phones back - without paying IMEI-check.co.suckourmoney.uk
@ twig2256
If your phone is CID unlocked try Drugstore's method of recovering Splash Screen frozen phones
cheers

YES
The values are the same for every DOC CHIP
When the MTTY conects to USB type exactly this...
task 28
(then it will work formating and cleaning the DOC
then it says succesfully clean
and now type...
task 28 55aa
it again works on the same process you can close the mtty without unplug your device... update your device with a Stock rom.
Actualy I have issues with mtty i dont know why i can acces to USB it say CMD GOD Damn can anybody helps...
This is the link that mestrini said for drug gsm store metod to unfreeze
http://forum.xda-developers.com/showthread.php?t=276963
Hey mestrini see this...
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader
even if it is universal it work for Wizard i did it once it works for me. but now it wont why????

zabardast_1 said:
Yes! WST only works on a working OS,have you tried to flash the official stock rom ?
Don't activesync or establish partnership,better if you altogether disable & close activesync and end process 'WCESCOMM.EXE' in the Task Manager and try to end as many applications running at the background.Don't surf the net,disable all anti virus and firewall.
Simply get the phone into Bootloaders mode,hook up with pc via usb cable,watch small usb appear at the bottom of Bootloader screen and run the Rom,hope it'll work.
Click to expand...
Click to collapse
can't solve my t-mobile mda

kaiser not starting

ok, some urgent help needed, yesterday ok, today will not start. only get as far as, 'smart mobility' R1.27.12.32 G22.45.88.07H D 1.56.00.00
phone is standard WM6 HTC. i have the 6.1 image for upgrading and tried to load using SD card, i get past tri colour screen, then loading, then checking then 'not allowed' and back to tri colour. it says KAIS130, SPL-1.93.000 CPLD-8. what?next
any help appreciated guys......

gazzacbr said:
ok, some urgent help needed, yesterday ok, today will not start. only get as far as, 'smart mobility' R1.27.12.32 G22.45.88.07H D 1.56.00.00
phone is standard WM6 HTC. i have the 6.1 image for upgrading and tried to load using SD card, i get past tri colour screen, then loading, then checking then 'not allowed' and back to tri colour. it says KAIS130, SPL-1.93.000 CPLD-8. what?next
any help appreciated guys......
Click to expand...
Click to collapse
To Flash a ROM you'll most likley need Hard SPL
Follow the "Getting Started" Link in my Sig.
If you cannot get WM to boot, you'll need to re-flash your orginal carriers ROM.
Ta
Dave

thanks for quick reply DaveShaw. fell at the first though, site for 'Cmonex's HardSPL 3.29SD' is blocked here in UAE, dont know why. are there any other links?

gazzacbr said:
thanks for quick reply DaveShaw. fell at the first though, site for 'Cmonex's HardSPL 3.29SD' is blocked here in UAE, dont know why. are there any other links?
Click to expand...
Click to collapse
You shouldn't be using cmonex's SD method the first time round. It is for upgrading only.
I have downloaded the package from point 2 (you should follow the USB method in post 3, NOT the SD set) and have upload it onto my site, please let me know when you are done with it.
http://taeguk.co.uk/xda/HardSPL and CidUnlocker.zip
Ta
Dave

ok, thanks DaveShaw, i have downloaded those files. the method in step 2 involves copying the jump progs to the device memory, which i do not have access to as it will not start. can i just copy to the sd card? thats why i was trying to flash a standard rom. i need a solution that will work just from the card. will the RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship.rar load using what i have on my phone now? i assume that the spl gets replaced when i upgrade to 6.1 with htc ruu. i can try anything as i have nothing to lose now (do i?)

gazzacbr said:
ok, thanks DaveShaw, i have downloaded those files. the method in step 2 involves copying the jump progs to the device memory, which i do not have access to as it will not start. can i just copy to the sd card? thats why i was trying to flash a standard rom. i need a solution that will work just from the card. will the RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship.rar load using what i have on my phone now? i assume that the spl gets replaced when i upgrade to 6.1 with htc ruu. i can try anything as i have nothing to lose now (do i?)
Click to expand...
Click to collapse
Enter your bootloader and try flashing any ROM supplied by your carrier to get into Windows Mobile.
What screen do you get stuck on? If it is the tri color screen check out the link in my signature.
Ta
Dave

Hi again, i am not actually 'stuck' on the screen as i can get into the loader, its just that i get the message saying that the (newer) rom will not load. i am extending my (c)rapidshare as free will not let me down load the 'standard' rom, then i will try that (just had to re-initialise my paypal and the passwords are on eWallet the phone, so ive reloaded the eWallet on my pc and ....so it goes on zzzzzzzzzz its funny how these things spiral down - not).
is there any way to update the spl only from the sd card?

gazzacbr said:
Hi again, i am not actually 'stuck' on the screen as i can get into the loader, its just that i get the message saying that the (newer) rom will not load. i am extending my (c)rapidshare as free will not let me down load the 'standard' rom, then i will try that (just had to re-initialise my paypal and the passwords are on eWallet the phone, so ive reloaded the eWallet on my pc and ....so it goes on zzzzzzzzzz its funny how these things spiral down - not).
is there any way to update the spl only from the sd card?
Click to expand...
Click to collapse
No.
Can your phone boot into Windows or not?
Ta
Dave

Hi, no, it will not boot to windows. just been reading around while 'RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship' is downloading. ive got connected with mtty and get cmd>. when i type boot i get 'Command Error !!!' i assume thats not good, i think rom is corrupted. tried standard HTC 6.1 RUU_Kaiser_HTC_FIN_3.29.414.0_radio_sign_25.83.40.02_1.65.17.56_Ship version 3.14.4.1 again on USB and after phone says 1% also message saying that it will not load error 294: invalid vendor id

gazzacbr said:
Hi, no, it will not boot to windows. just been reading around while 'RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship' is downloading. ive got connected with mtty and get cmd>. when i type boot i get 'Command Error !!!' i assume thats not good, i think rom is corrupted. tried standard HTC 6.1 RUU_Kaiser_HTC_FIN_3.29.414.0_radio_sign_25.83.40.02_1.65.17.56_Ship version 3.14.4.1 again on USB and after phone says 1% also message saying that it will not load error 294: invalid vendor id
Click to expand...
Click to collapse
Yeah, you need the ROM your carrier supplied.
Where is the Phone from?
Does a Hard Reset help?
Ta
Dave

woo hoo, yippeeeeeeeeeeeeee. the kaiser lives. back to standard 6.0 rom. cheers, i owe you a beer (or 2) if you are ever in abu dhabi, let me know ;-)
i can reload all from sprite backup (only from yesterday) to get me going again
but..... next will try to replace spl and then load 6.1. not sure why HTC standard would not let me update, i thought the ruu would update any htc phone
HardSPL 3.29 is first (yes?) then will try Kaiser_HTC_ASIA_HK_WWE_3.34.721.2 which sounds good. one more thing, my phone is not locked so do i need to do the 'SIM and CID-Unlock'

gazzacbr said:
woo hoo, yippeeeeeeeeeeeeee. the kaiser lives. back to standard 6.0 rom. cheers, i owe you a beer (or 2) if you are ever in abu dhabi, let me know ;-)
i can reload all from sprite backup (only from yesterday) to get me going again
but..... next will try to replace spl and then load 6.1. not sure why HTC standard would not let me update, i thought the ruu would update any htc phone
HardSPL 3.29 is first (yes?) then will try Kaiser_HTC_ASIA_HK_WWE_3.34.721.2 which sounds good. one more thing, my phone is not locked so do i need to do the 'SIM and CID-Unlock'
Click to expand...
Click to collapse
That's right, flash the HardSPL 3.29 first (SIM unlock is optional, CID unlock isn't needed - Hard SPL takes care of that - but it comes as part of the SIM unlock) then flash a WM6.1 ROM.
Ta
Dave

gazzacbr said:
not sure why HTC standard would not let me update, i thought the ruu would update any htc phone
Click to expand...
Click to collapse
Only if it's from the same region the RUU was intended for eg the European TyTN II's won't accept the latest Hong Kong WWE ROM by default because of this so as already suggested hardSPL works around this. My WM 6.0 UK original TyTN II upgraded to WM 6.1 OK but that was using the HTC UK provided ROM update. That updated everything required including the SPL and Radio to the required HTC versions. I'm back on the original WM 6.0 version though due to reliability issues with 6.1 and poor GPS performance.

I Think I just Bricked my AT&T Tilt

Uhh......yea......I was trying to upgrade my Rom to Dutty's Diamond V1 Build 19588. I was using the instructions from Flash-Your-Tilt . I got to Step 4 CID-Unlock it installed 100% rebooted and then nothing. Now the phone will only play the intro with no sound, then go black. It shows in the lower right hand R 1.70.02iNex, G25.65.30, D1.62.00.00. The phone will allow me to do a hard reset but after it it goes through the intro with screen alignment and installs the extra apps, it reboots and then goes black. I did a ton of reading through the wiki's if someone could point me in the right direction or tell me if its toast, it would be much appreciated.
Thanks

Be strong. I think it's only bricked when you can't power it on.
I have a poor net connection and not time atm. So a suggestion if you haven't already, search the forum for the word bricked. I'm sure this has happened before..
There are several tricks that people know so you might be ok. good luck.

Calihoe said:
Uhh......yea......I was trying to upgrade my Rom to Dutty's Diamond V1 Build 19588. I was using the instructions from Flash-Your-Tilt . I got to Step 4 CID-Unlock it installed 100% rebooted and then nothing. Now the phone will only play the intro with no sound, then go black. It shows in the lower right hand R 1.70.02iNex, G25.65.30, D1.62.00.00. The phone will allow me to do a hard reset but after it it goes through the intro with screen alignment and installs the extra apps, it reboots and then goes black. I did a ton of reading through the wiki's if someone could point me in the right direction or tell me if its toast, it would be much appreciated.
Thanks
Click to expand...
Click to collapse
Flash an OEM Rom/Radio Combo. Also it wont hurt if you already CID unlocked to to go ahead and flash a new SPL to it. Should fix any and all issues as your phone is still actually booting and Not bricked

Installing windows the 6.1 ROM from HTC's site worked. Thank you very much for the great advice. If I wanted to now put Dutty's ROM on my phone can I go straight to that, or do I need to restart the whole ROM flashing process(installing Jump SPL, Hard SPL and CID) ?

If you have unlocked it, just put duttys onto the SD card and rename the .nbh to KAISIMG.nbh
Put the phone into bootloader and install Its the fastest most successful method. No worry about a data cable coming out mid flash ( happened once to me....not fun )
Shouldnt have to install hardspl again ( or use JumpSPL )
Just make sure that if you are installing a WM6.0 rom that you have a WM6.0 radio. If not, the flashing process for the radio is the same ( rename to KAISIMG.nbh )

Is there a way to see if I the hard SPL install and CID unlock worked ? Can I just restart the whole process regardless. Sorry for the noob questions.

Calihoe said:
Is there a way to see if I the hard SPL install and CID unlock worked ? Can I just restart the whole process regardless. Sorry for the noob questions.
Click to expand...
Click to collapse
Go into bootloader. If your screen says hardspl somewhere near the top then you're good to go. Check which version because you can have radio problems if you use a WM6.0 spl with a WM6.1 rom. Most recent roms are WM6.1 so try HardSPL 3.29 or higher.
If you don't have hardspl, get it here for wm6.0 roms or here for wm6.1 roms.

many thanks, your advice with the links were invaluable. I read and read and read, but i guess i did not read enough. This site rocks.