What do you guys use to clean the finger grease off your phones? It seems like a bit of a magnet when it comes to grease
Apart from that, I LOVE it
Yeah, it is a grease magnet but hanging out with a little rag in the same pocket you carry your diamond solves it.
Talking bout Cleaning Diamond look at this: LINK
Luck
hmm thanks, I have a cloth.. But I never seem to get the screen back as it was before I touched it..
Luckily I managed to get the screen protector on w/o any bubbles or anything!!
I breath on mine before wiping it, and now I have learned to eat my chips with a fork!
LOL fair point, perhaps your right.. Maybe I should just wash more often
I use a micro fiber cloth - it brings it back to new in general. When really dirty I use my water based cleaning agent for flat screen TVs. That surely works.
Related
Did you guys notice there is a crack on the upper face of the phone right above the ear speaker and the small camera?
Well the thing is that if you carry your baby around in your pocket then its highly probable that a lot of crud and dirt will get stuck in that little crack.
So cleaning the crack at least once a week with a needle or something would be great maintenance.
Cheers boys.
Sergio PC said:
Did you guys notice there is a crack on the upper face of the phone right above the ear speaker and the small camera?
Well the thing is that if you carry your baby around in your pocket then its highly probable that a lot of crud and dirt will get stuck in that little crack.
So cleaning the crack at least once a week with a needle or something would be great maintenance.
Cheers boys.
Click to expand...
Click to collapse
Ummm - nope! No crack here. None that I can see with my bare eye, at least.
Cant see no crack on mine either...unless your talking about the gap between the body of the phone and the screen??..if so thats normal, every Diamond is like that and i suppose in time it will gather some crud and dirt there but then you can either clean it out or get a case that would cover that part.
Spawn12 said:
Cant see no crack on mine either...unless your talking about the gap between the body of the phone and the screen??..if so thats normal, every Diamond is like that and i suppose in time it will gather some crud and dirt there but then you can either clean it out or get a case that would cover that part.
Click to expand...
Click to collapse
you are right.
anyway, using a needle it is not recommended. why not with a plastic or wooden toothpick?
If you do it carefully your OK.
Im just to exited with my gorgeous phone.
cheers boys.
why dont post a pic next time
Hi,
I just ordered a new screen protector for my ATT Tilt lsince the bootlegg one that ATT gives you sucks!
The new screen protector comes with a little soft clothe that you can use to clean your screen, but the stock screen protector used glue/sticky stuff to hold on and now my screen is a little smeared with the glue and I don't want to push it to the corner from fear or it sliding under the case. Also, the screen is a still sticky and I want to clean it completely before putting on the new one.
So how can I get it completely clean? Is using a damp tissue okay? I don't want to get water in my phone and miss it up or anything so any advice is helpful. Thanks.
I don't know if you can classify it as glue, however when i took mine off, there wasn't any residue of any sort on it. Just take a lentless piece of cloth and swipe up to down. You can then get a blow dryer (put it on cool) and blow away and lint that is left on.
Idea....
Try a screen cleaning solution like.... It hurts to mention an apple related product..... iKlear/iClean when I worked retail, we used it on everything from PDA screens to $3000+ Sony laptop screens it's a very gentle cleaning solution and a little seems to go a long way. Also seemed to work great at removing left over residue from security devices.... that is if they hadn't been on there for more than a month...
Thanks for the input peeps. I am going to give them a try. Hopefully finding IKlear won't be too much of a hassle if the blow drying trick doesn't work.
So some inconsiderate person at work just picks up my phone without asking, and runs her broke-ass fingernails across the screen, BAM! instantly two fine hairline scratches right through the middle, all the way across. ARGG! Is there anyway I can buff these out, or get a new plastic screen?
Scratches...
Always use a screen protector... and don't let women touch your device - women and technology don't mix! (Only joking ladies ).
I found this on eBay - it's really good stuff.
Displex
Hope this helps.
It's probably a little too late, but a screen protector is always a good idea! Once you find out how to get it fixed, I highly recommend using one.
Well, it worked for mine but i still say test, do this:
- Toothpaste, it can be used to sand things with, like shiny plastics
- now, before you put half a tube on it, it would be safer to test first, take a little bit of toothpaste on your finger, little bit of water, mix between 2 fingers, then in circles rub a small corner of your screen, for a few minutes
- if it doesnt get less shiny, you can go rub circles over the scratch, once again a little toothpaste and a little drop of water to mix toothpaste with (makes it easyer to rub bscly)
The above got a nasty (unfortunatlly deep) scratch to be almost invisible when using device (cuz its deep u can still see it when the device is off) on my htc touch diamond, wich i caused the second day i got the device, by having the diamond and its headphones in the same pocket
The mentioned displex is a paste somewhere in between toothpaste and silver-cleaner-stuff, it would most likelly work better then my trick, but hey, maybe you can save yourself a few quids by getting the scratches off for 'free' (assuming you have toothpaste already) i do still advice you to even when you get displex test on a tiny part of a corner first, theres a whole lot of different plastics on phones. you can pick displex up at those phone stores that work with several contracters (orange tmobile etc)
This topic reminded me i didnt try with displex yet btw
Edit:
Another thing, screen protectors kinda suck on touch devices, since it reduces the capability to detect touch, always.
Didn't HTC state somewhere that it was amazing scratch proof glass and screen protector was only included out of habit?
suicidal.banana said:
.......
The mentioned displex is a paste somewhere in between toothpaste and silver-cleaner-stuff, it would most likelly work better then my trick, but hey, maybe you can save yourself a few quids by getting the scratches off for 'free' (assuming you have toothpaste already) i do still advice you to even when you get displex test on a tiny part of a corner first, theres a whole lot of different plastics on phones. you can pick displex up at those phone stores that work with several contracters (orange tmobile etc)
This topic reminded me i didnt try with displex yet btw
Edit:
Another thing, screen protectors kinda suck on touch devices, since it reduces the capability to detect touch, always.
Didn't HTC state somewhere that it was amazing scratch proof glass and screen protector was only included out of habit?
Click to expand...
Click to collapse
Displex is really awesome! Some ime ago i bought it for fixing my Laptop-Screen and even there (on an ASUS Crystal Display) it worked perfectly!
The only negative thing about Displex in my opinion is, that if you are using it too often, the screen will become kinda "unshiny" just like after polishing a car too much.... i noticed that after i used it several times to fix my Samsung D900 Screen
And regarding the screen protector delivered with the devide... I think it is a really good thing! I attached it to my Diamond after one week and didn't notice any differences... it even worked better when using the fingers to tap the screen.
Good advice here....tooth paste is good for removing most of a deep scratch BUT test first....
Displex to get the fine stuff....I would still test this as well, VERY CAREFULLY of course!!
Try this..
http://forum.xda-developers.com/showthread.php?t=415933
please search before you post...
Do not use toothpaste unless you test it first. Different toothpastes use different size grit. You may end up causing more problems.
To polish plastics, I use jeweller's rouge. Just rub some on a clean cloth and work away. It's slow but there's les chance of screwing things up.
If it's only a couple of fine scratches that are difficult to see, then leave it. Polishing will change the surface texture so you will need to polish the entire surface, not only the area of the scratches. It's doubtful that you'll find anything to match the original surface.
Okay, I'm gonna start with this that I have OCD. Now that you know, Let's get on with business.
This happened to my beloved tablet:
Don't ask why or how, it's a long story and frankly it doesn't matter now, it's done.
my purpose for this thread, was that how can I fix it?
I've tried ceramic paint, it was okay, but it had some serious flaws.
1. Hard to paint it with that. huge PITA with brush, better with a sponge but still really hard.
2. It's very stable, and can't be removed easily, but, it cracks and falls off after a while.
3. only one coat is not enough. it needs at least 3 coats to completely cover it, and with that many coats it is creates a big bulge which is a huge eye sore.
Now, I've came to this conclusion that paint is no good. I thought I going for a complete re-paint (as I really like black for these stuff, I thought that may be a good idea), but when I opened the back cover of the tablet, I changed my mind. Now, I need some suggestions.
Thank you.
Before you post something, remember, I have OCD.
so, replacing the back cover is out of the question.. Going be a tricky one to solve.
thats going to be a pain to fix but i still think paint is the way to go.
Use a high grit sand-paper and sand it down until its smooth.
Use a spay of black primer and put like 2 coats of primer on and allow time to dry between hands.
Then i would use a high gloss black spray paint. 2 to 3 light coats of that.
Then very lightly sand it down(more of roughing it up a bit, not actually sanding it down) with the highest grip sandpaper you can get your hands on.
Apply 2 coats of clearcoat.
finally use a buffing compound and lightly buff the surface, that will give you a mirror black finish.
Those are steps i have taken in the past to paint electronics and they lasted a while under normal use and i was happy with the results. You could probably find a better step by step guide online somewhere.
Oh, and make sure you mask the screen and the side panels with MORE then one layer of masking tape or you will scratch it.
m1l4droid said:
Thanks for the reply. You mean full body paint? But it's very sensitive, slightest mistake and you lost your USB or speakers... and it's very hard to cover the speakers, am I right?
And you mean to scratch the whole paint off? That's really hard, on this device which is quite big, and has markings on the back.
I was thinking maybe covering it with something like leather... I can design a pattern for it or something, no?
Sent from my Nexus S with CyanogenMod 9
Click to expand...
Click to collapse
well, the back cover pops off and you can do anything youwant to it without affecting device functionality. Iknow from my a500. As for the scratching, I meant that you dont want to scratch by accident your screen and the sides of the tablet, where the Ports are located. the paint will be a pain to do but with patience you could pull it off. you need to understand that since you are not a paint pro there will be a trade-off between the quality of the work and the self satisfaction of doing it yourself.
As for covering it, go to an upholstery shop and look at different fabrics. Get a really good glue, an exacto knife and a heatgun and get on it. Keep in mint that once the glue touches the tablet, there is no going back.
I finally installed the XOskin screen protector I got a while back.
It's been 17 hours since I installed it, about six hours in front of a heater register. I must have a hundred air bubbles! Doesn't look much different from this morning "before" a majority of the heated time. They say the micro bubbles go away in 24-48hrs. Don't know I'd call them micro bubbles and we'll see about them going away too.
Should get that guy that installed one in their video but he probably done a bunch. He had hardly any bubbles after installing it.
It's cut close near the speakers, top/bottom have some extra room but holes from the camera/sensor are tight. It took me three tries to get it right.
I put a Zagg on a 7" tab and don't remember this many bubbles. Maybe bigger doesn't mean easier?
wptski said:
I finally installed the XOskin screen protector I got a while back.
It's been 17 hours since I installed it, about six hours in front of a heater register. I must have a hundred air bubbles! Doesn't look much different from this morning "before" a majority of the heated time. They say the micro bubbles go away in 24-48hrs. Don't know I'd call them micro bubbles and we'll see about them going away too.
Should get that guy that installed one in their video but he probably done a bunch. He had hardly any bubbles after installing it.
It's cut close near the speakers, top/bottom have some extra room but holes from the camera/sensor are tight. It took me three tries to get it right.
I put a Zagg on a 7" tab and don't remember this many bubbles. Maybe bigger doesn't mean easier?
Click to expand...
Click to collapse
I installed Zaggs when I worked at Best Buy and was the go to guy there so I am going to see if I can explain this here and it might help some people out. (This is not me bragging, this is me trying to give back in whatever way I can)
First make sure you are using a clean surface and the air quality is pretty good (no dust floating around)
Next clean the screen with at least water, the spray included with Zagg and XO are actually pretty good cleaners too. You will need the cloth that comes with it to wipe it down later so use something like an extra microfiber cloth to clean it when it is wet.
Beat out the cloth that came with it against something. It will have dust in it, you need to get all that dust out. Wipe the dry screen down very well, make sure to end it you wipe all in one direction making sure there is no dust on the screen. I've found that if you start at the top and wipe towards yourself you will end up with no dust.
Spray the screen with the spray included while covering the holes that are showing on the front as you spray by them with that screen protector.
Spray the top of the screen protector (makes it easier for the squeegee to slide across and remove bubbles), and spray your fingers. (important step, saves so much grief later caused by finger prints or by trying really hard not to touch the back.)
Remove the protective backing making sure not to let any of the protector touch itself, that is a major problem with people trying their first time. Then spray the back of the protector generously and your fingers again.
Put the protector down and get it lined up. It will slide around pretty easily. When it is in line use the squeegee and make a line across the middle of the protector to hold it down.
Pull up half of it making sure not to go all the way to where you pressed it down and spray the screen and protector to make sure they are still wet and slowly squeegee it down. Start with the part touching the screen and squeegee, only laying down what the squeegee is pressing down. This will ensure that you don't create a bubble by just laying it down.
Pull up the other half to where you stopped the last time and repeat the last step with the other half.
You might end up with some liquid left in the protector, but the squeegee will get this out easily. Make sure you look at it from all angles with light hitting all sides so that you can see all the pockets. Squeegee out what remains and you are done.
It seems like a ton of work, but I consistently showed people up with this method. After putting enough down you just lay it and get it in line and squeegee the crap out of it, but this is the best way to learn. Remember that you will need some decent force to make sure you get it tight to the screen. Don't use too much though or you'll stretch it.
wptski said:
I finally installed the XOskin screen protector I got a while back.
It's been 17 hours since I installed it, about six hours in front of a heater register. I must have a hundred air bubbles! Doesn't look much different from this morning "before" a majority of the heated time. They say the micro bubbles go away in 24-48hrs. Don't know I'd call them micro bubbles and we'll see about them going away too.
Should get that guy that installed one in their video but he probably done a bunch. He had hardly any bubbles after installing it.
It's cut close near the speakers, top/bottom have some extra room but holes from the camera/sensor are tight. It took me three tries to get it right.
I put a Zagg on a 7" tab and don't remember this many bubbles. Maybe bigger doesn't mean easier?
Click to expand...
Click to collapse
are you sure you clean your screen perfectly before you apply it?
it might need longer time, like 24 hours - 48 hours, but it shouldn't that much bubble for 17 hours.
I apply the xoskin on my nexus 7 and end up with 1 bubble after about 24 hours or more, most probably because i didn't clean it well. Oh but well, the xoskin on my nexus 7 definitely reduce the sensitivity and sometimes makes the screen almost totally not responsive (i always gotta wipe the screen with something and it finally fixed). Might be the defect in my case but i don't wanna take a chance in their product again for now.
I used Monster screen cleaner with a micro fiber cloth, no cloth comes with the XOskin. One thing, it kind-of stuck and didn't slide around like the Zagg did. I wet it good on both sides but maybe because it took three tries, I should have rewet it??
In front of the heat register all day, no drastic change that I can tell and coming up on 24 hrs.
wptski said:
I used Monster screen cleaner with a micro fiber cloth, no cloth comes with the XOskin. One thing, it kind-of stuck and didn't slide around like the Zagg did. I wet it good on both sides but maybe because it took three tries, I should have rewet it??
In front of the heat register all day, no drastic change that I can tell and coming up on 24 hrs.
Click to expand...
Click to collapse
Yea, you have to rewet it when you reapply it. I would request a replacement from XO. I wouldn't put it in front of a heater either. If you squeegee it down good enough you don't need heat.
thacounty said:
Yea, you have to rewet it when you reapply it. I would request a replacement from XO. I wouldn't put it in front of a heater either. If you squeegee it down good enough you don't need heat.
Click to expand...
Click to collapse
I mean that I didn't have it completely laid down all way, I was off location a mile. You have to position by the camera/sensor holes and the top edge and there isn't much room for error. Sideways there is no room for error, overlap near the speakers and its edge will stick up.
I found the follow at the XOskin site:
How do I get rid of bubbles that appear after I’ve installed my XO Skins?
If it was recently that you installed the XO Skins, as soon as possible try pressing out the bubbles lightly with the squeegee. Make sure the squeegee is wet to avoid burn marks on the Skin. If the Skin has been dry for longer than a few hours, then the large bubbles are set in and you'll need a replacement. Small bubbles, or mini-bubbles, are normal and will disappear 24 to 48 hours after installation.
Whoops! I wonder what they call large and /or small bubbles? I removed it, wet applied to the sheet it came on on a flat surface. We'll see how it looks after a while and if it's worth a retry. Might have to get a replacement.
Like I mention, even when wet, it doesn't slide around easily. Maybe these are not as easy as a Zagg to install which has an orange peel surface which would allow the fluid in the pockets for easier movement?
wptski said:
I mean that I didn't have it completely laid down all way, I was off location a mile. You have to position by the camera/sensor holes and the top edge and there isn't much room for error. Sideways there is no room for error, overlap near the speakers and its edge will stick up.
I found the follow at the XOskin site:
How do I get rid of bubbles that appear after I’ve installed my XO Skins?
If it was recently that you installed the XO Skins, as soon as possible try pressing out the bubbles lightly with the squeegee. Make sure the squeegee is wet to avoid burn marks on the Skin. If the Skin has been dry for longer than a few hours, then the large bubbles are set in and you'll need a replacement. Small bubbles, or mini-bubbles, are normal and will disappear 24 to 48 hours after installation.
Whoops! I wonder what they call large and /or small bubbles? I removed it, wet applied to the sheet it came on on a flat surface. We'll see how it looks after a while and if it's worth a retry. Might have to get a replacement.
Like I mention, even when wet, it doesn't slide around easily. Maybe these are not as easy as a Zagg to install which has an orange peel surface which would allow the fluid in the pockets for easier movement?
Click to expand...
Click to collapse
I put xo skins on my evo 3d and my 2 touchpads when I had them. They don't slide as easily, you are correct, but keeping them wet will go a long way. That is why so much spray is included. Just make sure all bubbles are gone before you start letting it dry.
thacounty said:
I put xo skins on my evo 3d and my 2 touchpads when I had them. They don't slide as easily, you are correct, but keeping them wet will go a long way. That is why so much spray is included. Just make sure all bubbles are gone before you start letting it dry.
Click to expand...
Click to collapse
Too bad I didn't have /get more info before the first try. Yeah it probably needs lots of spray to let it slide but one has to be careful because of the speakers on the sides.
wptski said:
Too bad I didn't have /get more info before the first try. Yeah it probably needs lots of spray to let it slide but one has to be careful because of the speakers on the sides.
Click to expand...
Click to collapse
Yea, if you get liquid around them dry them out immediately. That's why I cover ports as I spray around them with the protector.