I finally installed the XOskin screen protector I got a while back.
It's been 17 hours since I installed it, about six hours in front of a heater register. I must have a hundred air bubbles! Doesn't look much different from this morning "before" a majority of the heated time. They say the micro bubbles go away in 24-48hrs. Don't know I'd call them micro bubbles and we'll see about them going away too.
Should get that guy that installed one in their video but he probably done a bunch. He had hardly any bubbles after installing it.
It's cut close near the speakers, top/bottom have some extra room but holes from the camera/sensor are tight. It took me three tries to get it right.
I put a Zagg on a 7" tab and don't remember this many bubbles. Maybe bigger doesn't mean easier?
wptski said:
I finally installed the XOskin screen protector I got a while back.
It's been 17 hours since I installed it, about six hours in front of a heater register. I must have a hundred air bubbles! Doesn't look much different from this morning "before" a majority of the heated time. They say the micro bubbles go away in 24-48hrs. Don't know I'd call them micro bubbles and we'll see about them going away too.
Should get that guy that installed one in their video but he probably done a bunch. He had hardly any bubbles after installing it.
It's cut close near the speakers, top/bottom have some extra room but holes from the camera/sensor are tight. It took me three tries to get it right.
I put a Zagg on a 7" tab and don't remember this many bubbles. Maybe bigger doesn't mean easier?
Click to expand...
Click to collapse
I installed Zaggs when I worked at Best Buy and was the go to guy there so I am going to see if I can explain this here and it might help some people out. (This is not me bragging, this is me trying to give back in whatever way I can)
First make sure you are using a clean surface and the air quality is pretty good (no dust floating around)
Next clean the screen with at least water, the spray included with Zagg and XO are actually pretty good cleaners too. You will need the cloth that comes with it to wipe it down later so use something like an extra microfiber cloth to clean it when it is wet.
Beat out the cloth that came with it against something. It will have dust in it, you need to get all that dust out. Wipe the dry screen down very well, make sure to end it you wipe all in one direction making sure there is no dust on the screen. I've found that if you start at the top and wipe towards yourself you will end up with no dust.
Spray the screen with the spray included while covering the holes that are showing on the front as you spray by them with that screen protector.
Spray the top of the screen protector (makes it easier for the squeegee to slide across and remove bubbles), and spray your fingers. (important step, saves so much grief later caused by finger prints or by trying really hard not to touch the back.)
Remove the protective backing making sure not to let any of the protector touch itself, that is a major problem with people trying their first time. Then spray the back of the protector generously and your fingers again.
Put the protector down and get it lined up. It will slide around pretty easily. When it is in line use the squeegee and make a line across the middle of the protector to hold it down.
Pull up half of it making sure not to go all the way to where you pressed it down and spray the screen and protector to make sure they are still wet and slowly squeegee it down. Start with the part touching the screen and squeegee, only laying down what the squeegee is pressing down. This will ensure that you don't create a bubble by just laying it down.
Pull up the other half to where you stopped the last time and repeat the last step with the other half.
You might end up with some liquid left in the protector, but the squeegee will get this out easily. Make sure you look at it from all angles with light hitting all sides so that you can see all the pockets. Squeegee out what remains and you are done.
It seems like a ton of work, but I consistently showed people up with this method. After putting enough down you just lay it and get it in line and squeegee the crap out of it, but this is the best way to learn. Remember that you will need some decent force to make sure you get it tight to the screen. Don't use too much though or you'll stretch it.
wptski said:
I finally installed the XOskin screen protector I got a while back.
It's been 17 hours since I installed it, about six hours in front of a heater register. I must have a hundred air bubbles! Doesn't look much different from this morning "before" a majority of the heated time. They say the micro bubbles go away in 24-48hrs. Don't know I'd call them micro bubbles and we'll see about them going away too.
Should get that guy that installed one in their video but he probably done a bunch. He had hardly any bubbles after installing it.
It's cut close near the speakers, top/bottom have some extra room but holes from the camera/sensor are tight. It took me three tries to get it right.
I put a Zagg on a 7" tab and don't remember this many bubbles. Maybe bigger doesn't mean easier?
Click to expand...
Click to collapse
are you sure you clean your screen perfectly before you apply it?
it might need longer time, like 24 hours - 48 hours, but it shouldn't that much bubble for 17 hours.
I apply the xoskin on my nexus 7 and end up with 1 bubble after about 24 hours or more, most probably because i didn't clean it well. Oh but well, the xoskin on my nexus 7 definitely reduce the sensitivity and sometimes makes the screen almost totally not responsive (i always gotta wipe the screen with something and it finally fixed). Might be the defect in my case but i don't wanna take a chance in their product again for now.
I used Monster screen cleaner with a micro fiber cloth, no cloth comes with the XOskin. One thing, it kind-of stuck and didn't slide around like the Zagg did. I wet it good on both sides but maybe because it took three tries, I should have rewet it??
In front of the heat register all day, no drastic change that I can tell and coming up on 24 hrs.
wptski said:
I used Monster screen cleaner with a micro fiber cloth, no cloth comes with the XOskin. One thing, it kind-of stuck and didn't slide around like the Zagg did. I wet it good on both sides but maybe because it took three tries, I should have rewet it??
In front of the heat register all day, no drastic change that I can tell and coming up on 24 hrs.
Click to expand...
Click to collapse
Yea, you have to rewet it when you reapply it. I would request a replacement from XO. I wouldn't put it in front of a heater either. If you squeegee it down good enough you don't need heat.
thacounty said:
Yea, you have to rewet it when you reapply it. I would request a replacement from XO. I wouldn't put it in front of a heater either. If you squeegee it down good enough you don't need heat.
Click to expand...
Click to collapse
I mean that I didn't have it completely laid down all way, I was off location a mile. You have to position by the camera/sensor holes and the top edge and there isn't much room for error. Sideways there is no room for error, overlap near the speakers and its edge will stick up.
I found the follow at the XOskin site:
How do I get rid of bubbles that appear after I’ve installed my XO Skins?
If it was recently that you installed the XO Skins, as soon as possible try pressing out the bubbles lightly with the squeegee. Make sure the squeegee is wet to avoid burn marks on the Skin. If the Skin has been dry for longer than a few hours, then the large bubbles are set in and you'll need a replacement. Small bubbles, or mini-bubbles, are normal and will disappear 24 to 48 hours after installation.
Whoops! I wonder what they call large and /or small bubbles? I removed it, wet applied to the sheet it came on on a flat surface. We'll see how it looks after a while and if it's worth a retry. Might have to get a replacement.
Like I mention, even when wet, it doesn't slide around easily. Maybe these are not as easy as a Zagg to install which has an orange peel surface which would allow the fluid in the pockets for easier movement?
wptski said:
I mean that I didn't have it completely laid down all way, I was off location a mile. You have to position by the camera/sensor holes and the top edge and there isn't much room for error. Sideways there is no room for error, overlap near the speakers and its edge will stick up.
I found the follow at the XOskin site:
How do I get rid of bubbles that appear after I’ve installed my XO Skins?
If it was recently that you installed the XO Skins, as soon as possible try pressing out the bubbles lightly with the squeegee. Make sure the squeegee is wet to avoid burn marks on the Skin. If the Skin has been dry for longer than a few hours, then the large bubbles are set in and you'll need a replacement. Small bubbles, or mini-bubbles, are normal and will disappear 24 to 48 hours after installation.
Whoops! I wonder what they call large and /or small bubbles? I removed it, wet applied to the sheet it came on on a flat surface. We'll see how it looks after a while and if it's worth a retry. Might have to get a replacement.
Like I mention, even when wet, it doesn't slide around easily. Maybe these are not as easy as a Zagg to install which has an orange peel surface which would allow the fluid in the pockets for easier movement?
Click to expand...
Click to collapse
I put xo skins on my evo 3d and my 2 touchpads when I had them. They don't slide as easily, you are correct, but keeping them wet will go a long way. That is why so much spray is included. Just make sure all bubbles are gone before you start letting it dry.
thacounty said:
I put xo skins on my evo 3d and my 2 touchpads when I had them. They don't slide as easily, you are correct, but keeping them wet will go a long way. That is why so much spray is included. Just make sure all bubbles are gone before you start letting it dry.
Click to expand...
Click to collapse
Too bad I didn't have /get more info before the first try. Yeah it probably needs lots of spray to let it slide but one has to be careful because of the speakers on the sides.
wptski said:
Too bad I didn't have /get more info before the first try. Yeah it probably needs lots of spray to let it slide but one has to be careful because of the speakers on the sides.
Click to expand...
Click to collapse
Yea, if you get liquid around them dry them out immediately. That's why I cover ports as I spray around them with the protector.
Related
Ok I got one of the anti-glare ones and I've got dust under it. The package says washable.....
I'm not too good with this but several websites say to use a little water in putting on one of these. Is it safe to do that with the Nook? Has anyone been able to put one on without getting dust under it?
Yes I have the anti glare on, with no dust and no water used.
The trick that I learned from applying screen covers on my Nexus, was if you get something underneath; lift it up, try not to get your fingers on the sticky side; and use a piece of scotch tape to lift off the dust from the sticky portion of the screen, then put it back down.
I had good luck installing the glossy protector. I didn't use water, I just scrubbed the screen with the felt that came in the packaging. Scrub it really well to get all the oil off (dont bare down really hard, just make multiple passes). Use clean hands while installing it. What I do is peal only the top 1/3 of the backing off, get it lined up on the screen (square to the top) and stick it down. Then slowly peal and press the remaining 2/3s. This way you never touch the sticky side, and you limit its exposure to incidental crud.
Hope that helps if you get what I mean.
Good luck!
I had dust under mine too. Didn't have a problem with the smaller phone screen but a tablet screen is harder to do. I washed mine and shook as much water off as I could and applied it. As I pushed the bubbles and water out to the edges, I dried it off with a cloth to prevent it from seeping into the nook. My nook is still running for 5 mos now.
My screen has been naked from when I got it. To tell you the truth, this screen can take a hell of a beating as I've dropped my keys on it once or twice and still not a single scratch.
I put the BandN hardshield type protector on mine and its bulletproof. It's kind of stiff so it's pretty easy to get on straight and if you do as suggested with the backpeel off its pretty easy to get on without dust. I got a tiny cat hair under the corner but it's hardly noticeable and doesn't cause any glare at all. You can't tell my nook even has a cover without sticking your nose on it.
There is a thread about this in the nook accessory forums area. They say to clean your screen and apply it in a steam filled bathroom. The steam from the shower keeps the dust out of the air. It worked great for me.
Sent from my Nook Color using XDA APP
JF-WS6 said:
There is a thread about this in the nook accessory forums area. They say to clean your screen and apply it in a steam filled bathroom. The steam from the shower keeps the dust out of the air. It worked great for me.
Sent from my Nook Color using XDA APP
Click to expand...
Click to collapse
I totally agree with this! After many Dsi and Ipod touch applications in my bathrom, I set off to do my NC in there too! The dust is so much less with the hot shower running, I got a Perfect install!
Ditto on the shower, only time ever that I got a perfect install was with a lil steam in the room. Also, if you want to go the extra mile, I read a tip somewhere that said to put a little water in a bowl, add a drop or two of dish soap and then dip your fingertips in it before applying. In a perfect world you would never touch the sticky side but I live far from there and with the soapy water deal helps a lot in repositioning since anything I touch dries clear.
You can actually get the whole sticky side SLIGHTY wet and just slide the thing around as long as you let it dry a day or so after install but I always worry about a drop of moisture sneaking in the side of the screen so I stick with finger tips.
Great...gonna have to peel it off tonight and try to reapply.
Used the anti-glare ones and got some dust under one. Just lifted the side with the dust and used some masking tape to get the dust stuck on the protector.
I applied my screen protector using the water trick. I used a little deionzed water. Just wet the screen protector, place it gently (you can move it around while it's wet). Then squeeze out the water using a card. While you do that collect the water off the edge using kitchen paper.
Sent from my NookColor using Tapatalk
Which protector did you use? I got one off amazon and it's just slightly off so that there's a large spot in one corner that's off.
I installed the Nook protector and decided that all I gained was another surface to collect fingerprints. It's glossy and not matte like other protectors so fingerprints show up just the same.
It did appear to make the touchscreen a little more stable. I don't seem to get as many false touches. Of course, it could just be me.
I am not sure it was worth it other than protecting the screen from any significant gouges.
Hi Nexus 7 fans,
Here at caseen we produced a video on how to install screen protector onto your Nexus 7! We used our GLARESHATTER Anti-Glare Dry Protection system for this video. It should help with anyone needing help installing a screen protection system.
For most dry application using Japanese PET, any additional bubbles will go out in 24 hours. Be sure to keep a CLEAN space!
Here is the video:
Link to screen protector system used in this video is here: http://www.caseen.com/caseen-2x-Goo...Anti-Fingerprint-Screen-Protectors_p_278.html
I'll be happy to answer any questions you guys might have
That nice, but you did it wrong.. I guess its like an Oreo cookie everyone has there own way of eating them
I would have just pealed about an inch off the top then applied it and slowly and softly pushed down as I peeled of the rest..
Cel1084 said:
That nice, but you did it wrong.. I guess its like an Oreo cookie everyone has there own way of eating them
I would have just pealed about an inch off the top then applied it and slowly and softly pushed down as I peeled of the rest..
Click to expand...
Click to collapse
Thats another way to do it ;P Both great ways IMO. The only reason I don't like that way is that too many issue with people accidentally touching the sticky part, and thereby adding oil to the installation =(.
Expert Tip: Keep scotch tape ripped and ready to go to catch any dust that may fall on the sticky portion during installaion. =].
caseenBrandon said:
Thats another way to do it ;P Both great ways IMO. The only reason I don't like that way is that too many issue with people accidentally touching the sticky part, and thereby adding oil to the installation =(.
Expert Tip: Keep scotch tape ripped and ready to go to catch any dust that may fall on the sticky portion during installaion. =].
Click to expand...
Click to collapse
They should use undusted latex gloves, and If you have access to It a heppa cirtifed Cleanroom. You can gets those dispozable clean suit at
home depot for under 20 bucks too.
Cel1084 said:
They should use undusted latex gloves, and If you have access to It a heppa cirtifed Cleanroom. You can gets those dispozable clean suit at
home depot for under 20 bucks too.
Click to expand...
Click to collapse
Haha! You know, after doing Zagg twice, I actually thought about doing it like that. All gowned up, wearing powderfree gloves and working in a BSC.
No more Zagg for me.
I always get mine wet. Helps get it down and slide a little bit to align. Also allows you to also remove any bubbles easier then a dry apply. Yes I'm talking about a dry application. A little soap helps too to prevent fingerprints.
Yea like oreos.
Sent from my Nexus 7 using xda premium
That installation video was brutal. In my house if I turned the screen protector over like had done, it wouldve had at least 1 or 2 dust particles catch on it. The way i do it is to always try to start from the top, peel back maybe an inch worth of the 1st guard, and lay it as perfect as possible all while holding the protector downwards. Then work your way down gently, push out the leftover bubbles with a microfiber cloth and my fingernail. Lift and dab with tape when necessary if dust bubbles occur.
Sent from my Nexus 7 using Tapatalk 2
so how's the feel on this one (is there any grip while swiping)? is there any orange peel? and how well does it reduce fingerprint?
Lol once i go back to school ill have access to a real cleanroom, may have to buy a new screen protector for it. But imo that wasnt a very good installation guide seeing how there were still some noticeable bubbles. The technique was good but Thats whT people are trying to avoid haha
Sent from my SAMSUNG-SGH-I747 using Tapatalk 2
I usually ignore any dusts/bubbles at the beginning. Of course, it's nice not to get them, but my main concern at the start is lining it up properly so that it sits perfect on the screen. Once I get that sorted, I use scotch tape and lift up every corner and clean up from below (while wearing lab nitrile gloves). I've had perfect applications using this method, though it takes time. Heck, it took me an hour and a half to get it absolutely perfect and bubble/dust free application for my Galaxy Nexus! Only took about 20 minutes to get a perfect and clean application for the Nexus 7
For those wondering, any bubbles on the screen protector will "dry out" after 24 hours [Ours is now bubble free after 24 hours of waiting]. I can understand wanting to do more! The more techniques performed the better. Just be ready to multi-task =).
NoTnERb said:
so how's the feel on this one (is there any grip while swiping)? is there any orange peel? and how well does it reduce fingerprint?
Click to expand...
Click to collapse
As a dry system there will be no noticeable orange peel. Also this one is super smooth, and does not grip your finger at all.
You won't need to wipe your screen for 2 weeks or more guaranteed. Our GLARESHATTER system takes care of fingerprints extremely well!
We have great Amazon reviews for our Nook Color version: http://www.amazon.com/caseen-GLARES...ie=UTF8&qid=1344896005&sr=8-9&keywords=caseen
You will like the Nexus 7 one =].
I am a Best Buy employee so should be no issue with getting an exchange. Looks like we have one of the 64GB AT&T ones in stock. Gonna be there bright and early to get mine exchanged.
I would advise everyone to keep an eye out.. I actually didn't notice it this morning. Around 6pm I noticed a black part on the screen and thought it was a glitch, so restarted but it was still there.
The line on the right side is just my temporary screen protector film. LOL. I bought an Invisishield and will install it on my replacement device tomorrow.
deepen915 said:
I am a Best Buy employee so should be no issue with getting an exchange. Looks like we have one of the 64GB AT&T ones in stock. Gonna be there bright and early to get mine exchanged.
I would advise everyone to keep an eye out.. I actually didn't notice it this morning. Around 6pm I noticed a black part on the screen and thought it was a glitch, so restarted but it was still there.
The line on the right side is just my temporary screen protector film. LOL. I bought an Invisishield and will install it on my replacement device tomorrow.
Click to expand...
Click to collapse
That's not a single deal pixel.
done12many2 said:
That's not a single deal pixel.
Click to expand...
Click to collapse
All good now.. got my replacement.
Also have installed a Invisible Shield.. After this picture was taken.
deepen915 said:
All good now.. got my replacement.
Also have installed a Invisible Shield.. After this picture was taken.
Click to expand...
Click to collapse
Did you go with the regular or HD InvisibleShield? I'm not a big fan of their new alcohol swab method for activating the adhesive on the HD model. I ended up using left over spray from several previous InvisibleShield installs.
When I used the alcohol swab provided, it just left lint embedded in he adhesive and I ended up with a bunch between the glass and the screen protector. I saw it before I even began to squeegee, so I broke out the spray and went old school. Turned out perfect after that.
InvisibleShield really screwed up this new application method because it leaves no room for error.
done12many2 said:
Did you go with the regular or HD InvisibleShield? I'm not a big fan of their new alcohol swab method for activating the adhesive on the HD model. I ended up using left over spray from several previous InvisibleShield installs.
When I used the alcohol swab provided, it just left lint embedded in he adhesive and I ended up with a bunch between the glass and the screen protector. I saw it before I even began to squeegee, so I broke out the spray and went old school. Turned out perfect after that.
InvisibleShield really screwed up this new application method because it leaves no room for error.
Click to expand...
Click to collapse
I did get the HD model. Yeah the swab was horrible. Mine had issues it has some lint on the bottom right corner. Screen is fully visible but slightly cloudy. Good thing I only paid $5 as an employee lol. I'll just buy another.
deepen915 said:
All good now.. got my replacement.
Also have installed a Invisible Shield.. After this picture was taken.
Click to expand...
Click to collapse
Actually, your InvisibleShield screen protector doesn't look anything like mine. Mine covers completely to through the curved edges. Is your protector for a different device?
deepen915 said:
I did get the HD model. Yeah the swab was horrible. Mine had issues it has some lint on the bottom right corner. Screen is fully visible but slightly cloudy. Good thing I only paid $5 as an employee lol. I'll just buy another.
Click to expand...
Click to collapse
Yeah, thanks for affirming that. I'm pretty sure they did the whole thing as a huge cost saving measure. It damn sure wasn't an improved method to install.
If you compare the savings between the difference in cost for the little plastic liquid spray canisters they provided and the supposed new and improved cheap alcohol swabs, Zagg just made out like a bandit.
Their packaging and marketing keeps getting better and better, but their quality and service keeps getting worse and worse.
done12many2 said:
Actually, your InvisibleShield screen protector doesn't look anything like mine. Mine covers completely to through the curved edges. Is your protector for a different device?
Click to expand...
Click to collapse
No this pic is yesterday morning and is not an invisible shield lol I said I installed after I took the pic. Installed it last night and looks just like yours. How did u do it so perfectly? I think I messed up by not using the squeegee in one motion. I did sections and I think it dried as I was doing it. I have some cloudiness and lint on the bottom. I'll have to get a new one.
deepen915 said:
No this pic is yesterday morning and is not an invisible shield lol I said I installed after I took the pic. Installed it last night and looks just like yours. How did u do it so perfectly? I think I messed up by not using the squeegee in one motion. I did sections and I think it dried as I was doing it. I have some cloudiness and lint on the bottom. I'll have to get a new one.
Click to expand...
Click to collapse
I knew as soon as I saw that piece of crap alcohol swap that the new method was flawed. ZAGG has lost their damn minds!!
The whole point behind getting these types of screen protectors on right is to get them and your fingers sprayed down really good. Once both are pretty much soaking, I pinch the protector between my finger and slide off excess fluid which in turn takes the lint/dust with it. Then I spray just a bit more on and apply it. I get it aligned and squeegee. While you are squeegeeing (is that a word?) and you come across a bubble that isn't going away, it isn't a bubble. It's lint/dust. Simply lift the protector at the edge and spray or apply some additional soapy water with your sprayer or fingers and get it out of there. Carefully fold the screen protector back so as to not allow additional lint/dust to get under there while you were dealing with the last one.
I don't try to use the squeegee to get every bubble. I just get most of the water out. Once 90% of it's gone, I work the edges with my fingers and around things like home buttons and camera lenses and sensors.
I guess my point is, even though their new instructions call for the use of the new alcohol swap, the old soapy water trick works perfectly fine. Actually, better.
done12many2 said:
I knew as soon as I saw that piece of crap alcohol swap that the new method was flawed. ZAGG has lost their damn minds!!
The whole point behind getting these types of screen protectors on right is to get them and your fingers sprayed down really good. Once both are pretty much soaking, I pinch the protector between my finger and slide off excess fluid which in turn takes the lint/dust with it. Then I spray just a bit more on and apply it. I get it aligned and squeegee. While you are squeegeeing (is that a word?) and you come across a bubble that isn't going away, it isn't a bubble. It's lint/dust. Simply lift the protector at the edge and spray or apply some additional soapy water with your sprayer or fingers and get it out of there. Carefully fold the screen protector back so as to not allow additional lint/dust to get under there while you were dealing with the last one.
I don't try to use the squeegee to get every bubble. I just get most of the water out. Once 90% of it's gone, I work the edges with my fingers and around things like home buttons and camera lenses and sensors.
I guess my point is, even though their new instructions call for the use of the new alcohol swap, the old soapy water trick works perfectly fine. Actually, better.
Click to expand...
Click to collapse
Alright so I'll buy another one tonight and see if that works. Good advice, thanks.
Here is what mine looks like.
deepen915 said:
Alright so I'll buy another one tonight and see if that works. Good advice, thanks.
Here is what mine looks like.
Click to expand...
Click to collapse
Looks pretty good to me. If your trying to get it closer to the edge, all I did was continue to work mine while it was still wet. Just a little at a time while I was working the water out from the center of the screen towards the edge.
Good luck man. Like I said, I think it looks great as it is now.
done12many2 said:
Looks pretty good to me. If your trying to get it closer to the edge, all I did was continue to work mine while it was still wet. Just a little at a time while I was working the water out from the center of the screen towards the edge.
Good luck man. Like I said, I think it looks great as it is now.
Click to expand...
Click to collapse
Got another one and did it again. Lint is gone now but got some micro bubbles. Let's see if it goes away. Not noticeable when screen is on.
Also even with no Zagg. I noticed some screen blemishes. Like it seems cloudy in some parts. I put brightness all the way while I was wiping it down to prepare the Zagg install. It's very noticeable. I may need to get my phone replaced again smh.
That completely sucks to hear about the cloudiness issue. I haven't heard of that one yet. I've heard of the swirls, scratches, and whites appearing yellow issues, but not the cloudiness.
I would lose my mind if I had to take a phone back twice for a screen related issue. It's probably not as big of a deal for you since you can do it while you're at work so to speak, but when your spending a grand on a phone, you just don't expect to have to take it back two times to be replaced.
Switching gears back to the bubbles in the Zagg. If you turn the screen on and they are barely noticeable, but with a slight prism light effect to them, you're fine. They'll dry up and be gone in hours.
If however you turn the screen on and see a shadow, it won't be going away when it's dried.
done12many2 said:
That completely sucks to hear about the cloudiness issue. I haven't heard of that one yet. I've heard of the swirls, scratches, and whites appearing yellow issues, but not the cloudiness.
I would lose my mind if I had to take a phone back twice for a screen related issue. It's probably not as big of a deal for you since you can do it while you're at work so to speak, but when your spending a grand on a phone, you just don't expect to have to take it back two times to be replaced.
Switching gears back to the bubbles in the Zagg. If you turn the screen on and they are barely noticeable, but with a slight prism light effect to them, you're fine. They'll dry up and be gone in hours.
If however you turn the screen on and see a shadow, it won't be going away when it's dried.
Click to expand...
Click to collapse
Yeah the Zagg is good enough for me.
And yeah I can see the cloudiness when scrolling on a white page in Chrome. I really don't want to have to exchange it again but may have to if it is really annoying me over the nextra few days.
It's like gray smudges going diagonally on the glass. I can't tell if its on the actual amoled panel or glass.
i have dead pixel on my Galaxy S6 Edge Plus
got the dead pixel after 4 Months using the phone.
how did i get a dead pixel??? i don't understand.
https://www.youtube.com/watch?v=_JbgaYIfdZo
seem's very small
do you think i should repair the phone?
I can't get all of the answers from their customer service but I am sure many would be interested to know answers to these questions. You can add your own.
1. Is the glue dangeours if it gets into the mic, speaker, inside buttons?
2. Can you install the glass over a decal sticker on bezels?
3. Does the surface have to be 100% level or is a degree or two off not such a problem?
4. Do they sell just a replacement glass/glue in case of breakage? No point spending extra money for the lamp if you already have one plus what are you going to do with extra lamps.
Thanks a bunch!
I can only answer #4. They do sell a kit with just the glass and glue, but it is only $5 less lol
refusedchaos said:
I can only answer #4. They do sell a kit with just the glass and glue, but it is only $5 less lol
Click to expand...
Click to collapse
What? That is kind of a rip off...
1. it can be dangerous if it gets in. use masking tape for the top speaker and one time around the phone so everything will be sealed.
2. maybe, but i wouldn't do it.
3. it needs to be level so the glue won't flow in the wrong direction.
4. yes but it's still 35 bucks or so
chrisknife said:
1. it can be dangerous if it gets in. use masking tape for the top speaker and one time around the phone so everything will be sealed.
2. maybe, but i wouldn't do it.
3. it needs to be level so the glue won't flow in the wrong direction.
4. yes but it's still 35 bucks or so
Click to expand...
Click to collapse
How do you then get masking tape off the top speaker? I am pretty sure it is not in demo videos?
If you follow the directions I don't see how you would get it in the hole. It should dump out just above center and you tip it towards the bottom in the "jig". Once you drop the protector it should only flow under the screen as long as you don't press then cure with light.
So... is it possible, sure if you do 1 or more things wrong during installation but it doesn't seem likely.
notefreak said:
What? That is kind of a rip off...
Click to expand...
Click to collapse
Yup
https://www.amazon.com/Whitestone-Dome-REPLACEMENT-PROTECTOR-Protector/dp/B075D74S7K/
I'm sure some company will come up with a cheaper alternative eventually. It is just a glass protector and loca glue.
According to Whitestone, the glue is not harmful to any components or yourself. You can wipe off excess glue with alcohol.
hx4700 Killer said:
If you follow the directions I don't see how you would get it in the hole. It should dump out just above center and you tip it towards the bottom in the "jig". Once you drop the protector it should only flow under the screen as long as you don't press then cure with light.
So... is it possible, sure if you do 1 or more things wrong during installation but it doesn't seem likely.
Click to expand...
Click to collapse
I am pretty sure it easily and normally gets into the front top speaker.
notefreak said:
I can't get all of the answers from their customer service but I am sure many would be interested to know answers to these questions. You can add your own.
1. Is the glue dangeours if it gets into the mic, speaker, inside buttons?
2. Can you install the glass over a decal sticker on bezels?
3. Does the surface have to be 100% level or is a degree or two off not such a problem?
4. Do they sell just a replacement glass/glue in case of breakage? No point spending extra money for the lamp if you already have one plus what are you going to do with extra lamps.
Thanks a bunch!
Click to expand...
Click to collapse
1. I had a little bit of seepage around my power button, and found some in my S-Pen slot - no damage done.
2. I think this is likely not to work terribly well. Anything that prevents the progress of the glue is likely to screw up the installation, and I suspect the edges of the decal would probably interfere.
3. I suspect that mine wasn't 100% flat, and it didn't cause problems (I had a bit of seepage both sides, not just the side that I suspect was marginally lower).
4. Yes, as has been mentioned, there is a new glass/glue option at a small saving over buying the whole kit again.
I stand corrected. I did my install last night and taped the speaker just in case and probably should have run tape around the perimeter of the phone as well. It came out nice but for one tiny bubble right at the curve that isn't visible when in use and mostly only in bright light.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Tips:
1. I definitely recommend taping not only the speaker but the perimeter below the glass so it can't go in buttons or ports. I had to wipe down the vol up/down side a bit.
2. Absolutely make sure the work surface is level. I have a tiny level I set across the screen face in both directions while it was inserted in to the jig to confirm this.
3. Write down the steps on a short, simple checklist you can refer to and put it on the table next to the phone so you don't miss any. I almost forgot to tilt the phone after removing the adhesive "bridge" and setting the tempered glass down in the slot and across the drop pin. A speck got on there right next to the glue and I freaked and had to pick up the protector and dab the dust bit up. That lead to me hurrying/panicking and nearly forgetting a step.
4. Either before you start or after you drop the glass on the glue and it spreads make sure you and/or the phone are in a position where you can inspect all sides/angles before applying the UV light. I may not have had the bubble if I had been in such a position to more thoroughly inspect. It was on the curve of the glass on the far side away from me and I didn't see it and I was afraid to move the jig :/
5. DO NOT remove any part of the positioning jig until you have hit it with the first 15 seconds of UV light. That cover is floating on a lot of liquid and will skate all over the place if you aren't careful.
6. You can gently tap/(very gently)push down a bit to push glue in to bubbles but be aware doing so will most likely lead to it "squirting" out the edge(s) a bit.
7. Do this when you are not in a hurry and well rested (not exhausted like I was). Make sure no one will bust in the room you are working and bug you (or swirl up the air). Do it in a clean environment. Wait for the AC to be OFF and no fans on so air isn't causing dust bits to swirl. I wore Nit-rile gloves to minimize any bits falling off my skin/hair (don't touch the screen with the gloves once cleaned or you may end up with a residue on it). If you are at all unsure about your install or what your results will be like DO NOT hit the glue with the UV light. Up until then it can be cleaned off and you have another bottle for try 2. Afterwards the say its impossible to clean and re-use thought I may put that to the test much later on.
If you want perfect results then EVERYTHING must go perfectly or you will not have perfect results. Even if its perfect bubbles may still get missed :/
**This screen protector install is NOT for the faint of heart or someone who is not willing to take the time and even dry run it a couple of times to be sure they have it down or the results will be less than optimal. This is coming from someone who can take apart these Samsung phones and replace the display itself!
hx4700 Killer said:
I stand corrected. I did my install last night and taped the speaker just in case and probably should have run tape around the perimeter of the phone as well. It came out nice but for one tiny bubble right at the curve that isn't visible when in use and mostly only in bright light.
View attachment 4278097
View attachment 4278098
Tips:
1. I definitely recommend taping not only the speaker but the perimeter below the glass so it can't go in buttons or ports. I had to wipe down the vol up/down side a bit.
2. Absolutely make sure the work surface is level. I have a tiny level I set across the screen face in both directions while it was inserted in to the jig to confirm this.
3. Write down the steps on a short, simple checklist you can refer to and put it on the table next to the phone so you don't miss any. I almost forgot to tilt the phone after removing the adhesive "bridge" and setting the tempered glass down in the slot and across the drop pin. A speck got on there right next to the glue and I freaked and had to pick up the protector and dab the dust bit up. That lead to me hurrying/panicking and nearly forgetting a step.
4. Either before you start or after you drop the glass on the glue and it spreads make sure you and/or the phone are in a position where you can inspect all sides/angles before applying the UV light. I would not have had the bubble if I had been in such a position. It was on the curve of the glass on the far side away from me and I didn't see it :/
5. DO NOT remove any part of the positioning jig until you have hit it with the first 15 seconds of UV light. That cover is floating on a lot of liquid and will skate all over the place if you aren't careful.
6. You can gently tap/(very gently)push down a bit to push glue in to bubbles but be aware doing so will most likely lead to it "squirting" out the edge(s) a bit.
7. Do this when you are not in a hurry and well rested (not exhausted like I was). Make sure no one will bust in the room you are working and bug you (or swirl up the air). Do it in a clean environment. Wait for the AC to be OFF and no fans on so air isn't causing dust bits to swirl. I wore Nit-rile gloves to minimize any bits falling off my skin/hair (don't touch the screen with the gloves once cleaned or you may end up with a residue on it). If you are at all unsure about your install or what your results will be like DO NOT hit the glue with the UV light. Up until then it can be cleaned off and you have another bottle for try 2. Afterwards the say its impossible to clean and re-use thought I may put that to the test much later on.
If you want perfect results then EVERYTHING must go perfectly or you will not have perfect results. Even if its perfect bubbles may still get missed :/
**This screen protector install is NOT for the faint of heart or someone who is not willing to take the time and even dry run it a couple of times to be sure they have it down or the results will be less than optimal. This is coming from someone who can take apart these Samsung phones and replace the display itself!
Click to expand...
Click to collapse
I didn't tape anything off and had to wipe a little glue off the side where the volume buttons are located. The glue didn't get into the speakers or any ports. The glue didn't even make to the volume buttons (close to the buttons but not touching.
Definitely make sure to have a level surface. I used the Bubble Level app to ensure the surface I was working on was level.
I watched the youtube videos a couple times and had it running while I was performing the install. Aside from the barely noticeable two air bubbles (and I mean BARELY noticeable), the install was fairly straight forward and easy.
warkentinkd said:
I didn't tape anything off and had to wipe a little glue off the side where the volume buttons are located. The glue didn't get into the speakers or any ports. The glue didn't even make to the volume buttons (close to the buttons but not touching.
Definitely make sure to have a level surface. I used the Bubble Level app to ensure the surface I was working on was level.
I watched the youtube videos a couple times and had it running while I was performing the install. Aside from the barely noticeable two air bubbles (and I mean BARELY noticeable), the install was fairly straight forward and easy.
Click to expand...
Click to collapse
I will grant you, if you don't give a crap what it looks like then yes. Its easy. I am a perfectionist. It requires absolute perfection if you want perfect results. There is no room for error, and no "fix" it later if you screw up. Other tempered glass you can remove, use tape and pull debris off it and re-install. This says you can't remove it once glued and re-use. To quote them "It is impossible"
So when your installing it, and you want perfection and you think about the fact that $50 is on the line if you blow it well.... its more stress than I like for doing that job.
It also yields the best results of any protector I have ever used so risk vs reward I guess.
hx4700 Killer said:
I will grant you, if you don't give a crap what it looks like then yes. Its easy. I am a perfectionist. It requires absolute perfection if you want perfect results. There is no room for error, and no "fix" it later if you screw up. Other tempered glass you can remove, use tape and pull debris off it and re-install. This says you can't remove it once glued and re-use. To quote them "It is impossible"
So when your installing it, and you want perfection and you think about the fact that $50 is on the line if you blow it well.... its more stress than I like for doing that job.
It also yields the best results of any protector I have ever used so risk vs reward I guess.
Click to expand...
Click to collapse
Good luck with that. lol
I have circled the two air bubbles that I have. Only noticeable with the screen off.
warkentinkd said:
Good luck with that. lol
I have circled the two air bubbles that I have. Only noticeable with the screen off.
Click to expand...
Click to collapse
Now with attachment. lol
hx4700 Killer said:
I stand corrected. I did my install last night and taped the speaker just in case and probably should have run tape around the perimeter of the phone as well. It came out nice but for one tiny bubble right at the curve that isn't visible when in use and mostly only in bright light.
Tips:
1. I definitely recommend taping not only the speaker but the perimeter below the glass so it can't go in buttons or ports. I had to wipe down the vol up/down side a bit.
2. Absolutely make sure the work surface is level. I have a tiny level I set across the screen face in both directions while it was inserted in to the jig to confirm this.
3. Write down the steps on a short, simple checklist you can refer to and put it on the table next to the phone so you don't miss any. I almost forgot to tilt the phone after removing the adhesive "bridge" and setting the tempered glass down in the slot and across the drop pin. A speck got on there right next to the glue and I freaked and had to pick up the protector and dab the dust bit up. That lead to me hurrying/panicking and nearly forgetting a step.
4. Either before you start or after you drop the glass on the glue and it spreads make sure you and/or the phone are in a position where you can inspect all sides/angles before applying the UV light. I may not have had the bubble if I had been in such a position to more thoroughly inspect. It was on the curve of the glass on the far side away from me and I didn't see it and I was afraid to move the jig :/
5. DO NOT remove any part of the positioning jig until you have hit it with the first 15 seconds of UV light. That cover is floating on a lot of liquid and will skate all over the place if you aren't careful.
6. You can gently tap/(very gently)push down a bit to push glue in to bubbles but be aware doing so will most likely lead to it "squirting" out the edge(s) a bit.
7. Do this when you are not in a hurry and well rested (not exhausted like I was). Make sure no one will bust in the room you are working and bug you (or swirl up the air). Do it in a clean environment. Wait for the AC to be OFF and no fans on so air isn't causing dust bits to swirl. I wore Nit-rile gloves to minimize any bits falling off my skin/hair (don't touch the screen with the gloves once cleaned or you may end up with a residue on it). If you are at all unsure about your install or what your results will be like DO NOT hit the glue with the UV light. Up until then it can be cleaned off and you have another bottle for try 2. Afterwards the say its impossible to clean and re-use thought I may put that to the test much later on.
If you want perfect results then EVERYTHING must go perfectly or you will not have perfect results. Even if its perfect bubbles may still get missed :/
**This screen protector install is NOT for the faint of heart or someone who is not willing to take the time and even dry run it a couple of times to be sure they have it down or the results will be less than optimal. This is coming from someone who can take apart these Samsung phones and replace the display itself!
Click to expand...
Click to collapse
I had bubbles in the top center and took off after two days. That's glue did not come off screen protector and trying to wipe off glue caused scratches on the inside off the glass. So now I have to but another package. I love the way it looked but be very careful on the part of lowering the glass after applying the glue. I went too fast and let it slam down and got bubbles. I watched a video saying u can take off and reapply, yeah that didn't work.
Be really careful, and tape the head speaker in case...
I'll tell you my story, which Murphy's law hit me with! I admit i didn't think this would happen to me... but it did, as always.
So i was being really careful, as this is a one shot story... watched the youtube video, surface was perfectly flat, the glass perfectly clean. Once the "glue" was put I saw a little dust, took it away, I was about to put the glass on top, fingers were stable as a sniper... Then suddenly out of nowhere two things happen : 1. i forgot to put the volume of my computer down and got a message which surprised me, 2. my dog decided to run after a bird across my office and while doing so hit my knee under my table... the destabilised me, the glass fell on the screen, didn't land on the level bar obviously and splashed the glue all over the place... and into the top speaker grill.... luckily i had an alcohol bottle and some cotton swap next to me, so i immediately cleaned the speaker but I guess some glue fell inside...
result : i was able to perfectly align the glass, small air bubbles that i was able to move out thanks to a hairdryer, I was able to recover 80% of my volume in my damaged speaker... but still trying to figure a way to win those 20%. Seems like some liquid is still on/inside the speaker OR the glue dried on the speaker INSIDE....trying with the hairdryer, maybe the cotton swab alcohol dripped inside. Well if anyone has an idea how to recuperate that lose, please share.
Just in case you have air bubble, use a hairdryer... but be careful of the heat. Also, i tried it on my Ringke Onyx.. it barely didn't work, so it bended a corner of the glass... but when i changed cases, used the hairdryer, and it fixed the issue.
Trial and error, trust me, you wanna put that tape, just in case Murphy decides to write a new law with you as example...
notefreak said:
How do you then get masking tape off the top speaker? I am pretty sure it is not in demo videos?
Click to expand...
Click to collapse
Is this a serious question?
Kawaisa said:
Is this a serious question?
Click to expand...
Click to collapse
I just used scotch tape. It came off easily. You are supposed to run the light for 15 seconds on each end first then remove from the holder. Wipe off excess around screen and then do the final cure. Tape just lifted off and removing any excess glue around the perimeter is easy.
FIRST STEP MAKE SURE THE UV LIGHT WORKS. My first one the uv light was junk and I already had glue on. Really annoying.
I would also watch out when taking the bridge off with the uv glue. It can drip. I had it happen twice. I was worried the drips would cause a bubble so I picked up the whole thing and tilted it like the old game where you tilt the playing surface and move the ball around a maze. The puddle will move around like a ball of Mercury. Move the main puddle of glue to the drips and they join it like the liquid metal of the T-1000 in terminator 2. Then move the whole puddle back and gently set it down. Finish your install. I have done 3 now and think I can get it perfect every time.
Make sure you pinch the tray together at the bottom when you lay the glass on just before release. I had the tray separate and the whole glass slid between and fell right past the stopping tab you pull out and onto the phone in the wrong spot. Next time I made sure and pinch the bottom of the tray as I set the glass on it.
I also successfully removed the glass from a cured phone without breaking the glass. Just lift carefully from each edge and work your way in. You must go very slow and use very little force. I bet the glass could be cleaned up. I tried acetone and gave up as it didn't make a dent in it. That glue is tough. There may be something out there that will remove the glue and not jack the glass up I just don't want to invest time in it.
I need to vent, I'm so pissed off. Back in January I got a Whitestone Dome when they were on sale. I was happy with my plastic protector at the time, so I didn't install it right away. Fast forward to last night...
I watched a solid dozen Note8 install videos on YouTube, have been reading for months on reddit and xda all the other threads, and executed my installation perfectly according to the directions. I even taped off the earpiece just in case. Not to brag, but I'm usually really good with this sort of stuff. It ended in disaster due to the poor quality control of this product and its company.
I have read quite a few horror stories on social media about Whitestone's products, but I assumed if I was very careful I could do a successful install. WRONG. The supplied vial of glue was way too much, and after perfectly applying the glue and dropping the glass on top, capillary action pulled the glue nicely across the screen and I was very pleased. It looked beautiful. After waiting the full 15 seconds top and 15 seconds bottom, I removed my Note8 from the tray as instructed. To my horror, TONS of liquid excess glue was dripping down the sides. My S-Pen was DRIPPING with glue! There was glue everywhere, even in the bottom of the plastic jig. AND THE SCREEN WAS STILL LOOSE! After trying my best to clean up that huge mess, I followed the instructions to do the "secondary" cure. AFTER MULTIPLE MINUTES UNDER THE SUPPLIED UV LIGHT, THE GLUE IS STILL WET! My phone STINKS of this chemical, and every crevice of it is oozing this glue that will not cure under the UV light. I was meticulous about everything, there is nothing I did wrong. And besides WHY WON'T THE GLUE FULLY CURE UNDER UV!? I used the supplied USB cable, and a powerful Samsung USB wall charger so I know the light isn't "weak." I will admit that the screen has stopped moving around as of today, so something has sorta cured. But the edges are still wet, and leave an oily residue when touched, and look furry because there is so much tacky, sticky residue still oozing out.
What a horrible mess. It took me hours to clean everything up, and there is still glue in every tiny crevice of my Note8. I hope I got my S-Pen out and wiped off in time - it's still working, for now.
Always take your S-Pen out first!
ffolkes said:
I need to vent, I'm so pissed off. Back in January I got a Whitestone Dome when they were on sale. I was happy with my plastic protector at the time, so I didn't install it right away. Fast forward to last night...
I watched a solid dozen Note8 install videos on YouTube, have been reading for months on reddit and xda all the other threads, and executed my installation perfectly according to the directions. I even taped off the earpiece just in case. Not to brag, but I'm usually really good with this sort of stuff. It ended in disaster due to the poor quality control of this product and its company.
I have read quite a few horror stories on social media about Whitestone's products, but I assumed if I was very careful I could do a successful install. WRONG. The supplied vial of glue was way too much, and after perfectly applying the glue and dropping the glass on top, capillary action pulled the glue nicely across the screen and I was very pleased. It looked beautiful. After waiting the full 15 seconds top and 15 seconds bottom, I removed my Note8 from the tray as instructed. To my horror, TONS of liquid excess glue was dripping down the sides. My S-Pen was DRIPPING with glue! There was glue everywhere, even in the bottom of the plastic jig. AND THE SCREEN WAS STILL LOOSE! After trying my best to clean up that huge mess, I followed the instructions to do the "secondary" cure. AFTER MULTIPLE MINUTES UNDER THE SUPPLIED UV LIGHT, THE GLUE IS STILL WET! My phone STINKS of this chemical, and every crevice of it is oozing this glue that will not cure under the UV light. I was meticulous about everything, there is nothing I did wrong. And besides WHY WON'T THE GLUE FULLY CURE UNDER UV!? I used the supplied USB cable, and a powerful Samsung USB wall charger so I know the light isn't "weak." I will admit that the screen has stopped moving around as of today, so something has sorta cured. But the edges are still wet, and leave an oily residue when touched, and look furry because there is so much tacky, sticky residue still oozing out.
What a horrible mess. It took me hours to clean everything up, and there is still glue in every tiny crevice of my Note8. I hope I got my S-Pen out and wiped off in time - it's still working, for now.
Always take your S-Pen out first!
Click to expand...
Click to collapse
My s-pen was in the whole time too, nothing got in mine so not sure why it did with yours. You're right though, even with the tape/sponges the glue still goes everywhere. I cured it a little before moving it, and that did help keep the screen in place. Then I cured a little more afterwards and let it sit for a while... You can just carefully rinse/wash off the excess glue after. End result was good in my case, but the process can definitely be a messy experience.
sefrcoko said:
My s-pen was in the whole time too, nothing got in mine so not sure why it did with yours. You're right though, even with the tape/sponges the glue still goes everywhere. I cured it a little before moving it, and that did help keep the screen in place. Then I cured a little more afterwards and let it sit for a while... You can just carefully rinse/wash off the excess glue after. End result was good in my case, but the process can definitely be a messy experience.
Click to expand...
Click to collapse
I know I read you can wash it off somewhere else, but I thought it was oily. Is it really water soluble? I feel like bathing my phone is only going to make things worse right now haha.
ffolkes said:
I know I read you can wash it off somewhere else, but I thought it was oily. Is it really water soluble? I feel like bathing my phone is only going to make things worse right now haha.
Click to expand...
Click to collapse
It definitely feels oily, but I didn't end up having too much trouble getting it off in the end. I just ran the faucet and used my hand to wipe away what I could, rinsed hand, and repeated. Maybe a drop of hand soap at the worst, but I don't remember now. Never put the phone directly under water though...why tempt fate .Thankfully I don't have to do that more often lol
ffolkes said:
I need to vent, I'm so pissed off. Back in January I got a Whitestone Dome when they were on sale. I was happy with my plastic protector at the time, so I didn't install it right away. Fast forward to last night...
I watched a solid dozen Note8 install videos on YouTube, have been reading for months on reddit and xda all the other threads, and executed my installation perfectly according to the directions. I even taped off the earpiece just in case. Not to brag, but I'm usually really good with this sort of stuff. It ended in disaster due to the poor quality control of this product and its company.
I have read quite a few horror stories on social media about Whitestone's products, but I assumed if I was very careful I could do a successful install. WRONG. The supplied vial of glue was way too much, and after perfectly applying the glue and dropping the glass on top, capillary action pulled the glue nicely across the screen and I was very pleased. It looked beautiful. After waiting the full 15 seconds top and 15 seconds bottom, I removed my Note8 from the tray as instructed. To my horror, TONS of liquid excess glue was dripping down the sides. My S-Pen was DRIPPING with glue! There was glue everywhere, even in the bottom of the plastic jig. AND THE SCREEN WAS STILL LOOSE! After trying my best to clean up that huge mess, I followed the instructions to do the "secondary" cure. AFTER MULTIPLE MINUTES UNDER THE SUPPLIED UV LIGHT, THE GLUE IS STILL WET! My phone STINKS of this chemical, and every crevice of it is oozing this glue that will not cure under the UV light. I was meticulous about everything, there is nothing I did wrong. And besides WHY WON'T THE GLUE FULLY CURE UNDER UV!? I used the supplied USB cable, and a powerful Samsung USB wall charger so I know the light isn't "weak." I will admit that the screen has stopped moving around as of today, so something has sorta cured. But the edges are still wet, and leave an oily residue when touched, and look furry because there is so much tacky, sticky residue still oozing out.
What a horrible mess. It took me hours to clean everything up, and there is still glue in every tiny crevice of my Note8. I hope I got my S-Pen out and wiped off in time - it's still working, for now.
Always take your S-Pen out first!
Click to expand...
Click to collapse
What a nightmare. I fear using glue that might run down and block all my holes and crevices LOL.
Sent from my SM-N950U using Tapatalk
I had this issue when I was installing the Whitestone Dome on my S8+.
The sides and back of the phone were dripping with the greasy ass glue.
However, I've had no issues since with my Note 8.
I would like to add that when i was applying it to the S8+ I don't think the surface was entirely flat- the tip I saw was to use the glue vials and put them on the table to see if they'd roll; I did this until I had a perfectly level table.
I managed to install the protector flawlessly on my Note 8 without any issues.
I'm sure if you contact Whitestone they'll be able to provide you with another vial if you've used both.
Are you certain that the screen was dry before you applied it?
Definitely not trying to be contradictory
But for my Note 8 the install was easy, no mess, no problems...... Went just like instructions
S-Pen still works, and I must say the glass looks fantastic. Edges aren't great, but I vigorously rubbed the sides in one direction with a cloth. Over and over, until eventually the ragged glue on the edges sorta wiped away. I'm sure there will be problems down the road, but it's good for now at least. I also used some scraps of tape to try to remove the excess tacky glue that didn't wipe away. Just have to remember to use 1/3 less glue next time. Maybe remove the vial right after removing the second cap, rather than waiting for it to completely empty out.
ive replace my whitestone twice already. never any issue with the install. I wish the glass was stronger though. First crack was a legit saved my phone. someone bumped me on accident and screen down onto a bunch of pebbles. left junks missing from the protector but totally safe screen. last one was fell of my bed and chipped of the whole top edges and a nice crack across. but.... still saved the phone so i'm loyal
I hate to necro this thread considering its two years old but I just had the same painful experience on my Note 10+ 5G LOCA somehow managed to leak into my SPen slot. If you're thinking of buying this screen protector. Don't. You're better off with nothing.
Edit: After re-registering my fingerprints for the 3rd time it is working much faster and the SPen has seemed to loosen up after repeatedly taking it out and putting it back in and now appears to charge just fine.