Argh...applying screen guard - Nook Color General

Ok I got one of the anti-glare ones and I've got dust under it. The package says washable.....
I'm not too good with this but several websites say to use a little water in putting on one of these. Is it safe to do that with the Nook? Has anyone been able to put one on without getting dust under it?

Yes I have the anti glare on, with no dust and no water used.
The trick that I learned from applying screen covers on my Nexus, was if you get something underneath; lift it up, try not to get your fingers on the sticky side; and use a piece of scotch tape to lift off the dust from the sticky portion of the screen, then put it back down.

I had good luck installing the glossy protector. I didn't use water, I just scrubbed the screen with the felt that came in the packaging. Scrub it really well to get all the oil off (dont bare down really hard, just make multiple passes). Use clean hands while installing it. What I do is peal only the top 1/3 of the backing off, get it lined up on the screen (square to the top) and stick it down. Then slowly peal and press the remaining 2/3s. This way you never touch the sticky side, and you limit its exposure to incidental crud.
Hope that helps if you get what I mean.
Good luck!

I had dust under mine too. Didn't have a problem with the smaller phone screen but a tablet screen is harder to do. I washed mine and shook as much water off as I could and applied it. As I pushed the bubbles and water out to the edges, I dried it off with a cloth to prevent it from seeping into the nook. My nook is still running for 5 mos now.

My screen has been naked from when I got it. To tell you the truth, this screen can take a hell of a beating as I've dropped my keys on it once or twice and still not a single scratch.

I put the BandN hardshield type protector on mine and its bulletproof. It's kind of stiff so it's pretty easy to get on straight and if you do as suggested with the backpeel off its pretty easy to get on without dust. I got a tiny cat hair under the corner but it's hardly noticeable and doesn't cause any glare at all. You can't tell my nook even has a cover without sticking your nose on it.

There is a thread about this in the nook accessory forums area. They say to clean your screen and apply it in a steam filled bathroom. The steam from the shower keeps the dust out of the air. It worked great for me.
Sent from my Nook Color using XDA APP

JF-WS6 said:
There is a thread about this in the nook accessory forums area. They say to clean your screen and apply it in a steam filled bathroom. The steam from the shower keeps the dust out of the air. It worked great for me.
Sent from my Nook Color using XDA APP
Click to expand...
Click to collapse
I totally agree with this! After many Dsi and Ipod touch applications in my bathrom, I set off to do my NC in there too! The dust is so much less with the hot shower running, I got a Perfect install!

Ditto on the shower, only time ever that I got a perfect install was with a lil steam in the room. Also, if you want to go the extra mile, I read a tip somewhere that said to put a little water in a bowl, add a drop or two of dish soap and then dip your fingertips in it before applying. In a perfect world you would never touch the sticky side but I live far from there and with the soapy water deal helps a lot in repositioning since anything I touch dries clear.
You can actually get the whole sticky side SLIGHTY wet and just slide the thing around as long as you let it dry a day or so after install but I always worry about a drop of moisture sneaking in the side of the screen so I stick with finger tips.

Great...gonna have to peel it off tonight and try to reapply.

Used the anti-glare ones and got some dust under one. Just lifted the side with the dust and used some masking tape to get the dust stuck on the protector.

I applied my screen protector using the water trick. I used a little deionzed water. Just wet the screen protector, place it gently (you can move it around while it's wet). Then squeeze out the water using a card. While you do that collect the water off the edge using kitchen paper.
Sent from my NookColor using Tapatalk

Which protector did you use? I got one off amazon and it's just slightly off so that there's a large spot in one corner that's off.

I installed the Nook protector and decided that all I gained was another surface to collect fingerprints. It's glossy and not matte like other protectors so fingerprints show up just the same.
It did appear to make the touchscreen a little more stable. I don't seem to get as many false touches. Of course, it could just be me.
I am not sure it was worth it other than protecting the screen from any significant gouges.

Related

Applying too much pressure to amoled screen?

so I was installing a new screen protector yesterday, I was pressing down the bubbles with my fingers, over a microfiber cloth of course, and applying pressure to single points on the screen with the tips of my fingers to get the individual bubbles out. I now at the time I was using alot more pressure than what I I shoud have
I didnt realise how hard i was pressing down and then I stopped
the screen was not tarnished at all, bo bruises or spotting on the particular areas I put massive amounts of pressure on
now I can guarantee you that if this was an lcd thier would be some sort of bruising on the screen, lots of it actually. my main concern is that I may have used to much strenght ( im a big strong dude haha) is their any chance I could have messed something up
I know lcd and amoled are differnt technologies so can someone explain to me how its built, why thier is no brusins and wether I should be worried about this, I would just like to understand the tech because im pretty suprised that nothing happened to the screen
but maybe something I cant see or that may arrive later, I do understand their is glass. Does it have any give etc?
like is the does the glass protect it enough to actually keep pressure from reaching the amoled tech?
I did the same thing; wondered the same wonder
Like, word for word that's what I did putting on my protector, and was amazed just as you were at how damn strong that screen is. Amazing ****.
Gorilla Glass is some strong stuff. Next time though, try using a credit card or a really thick business card.
Use the edge of the card to push the protector down. Do this in a forward sliding motion until the protector is completely applied. Doing this will make it a lot easier to get the bubbles out.
Also, I typically use rubbing alcohol to clean the screen. Afterwards, I use some Scotch tape and tap it across the screen. This will make sure you have cleaned off any remaining lint and dust.
Sent from my SAMSUNG-SGH-I897 using XDA App

HOW TO: Install a screen protector on your Google Nexus 7 Tablet (Dry Application)

Hi Nexus 7 fans,
Here at caseen we produced a video on how to install screen protector onto your Nexus 7! We used our GLARESHATTER Anti-Glare Dry Protection system for this video. It should help with anyone needing help installing a screen protection system.
For most dry application using Japanese PET, any additional bubbles will go out in 24 hours. Be sure to keep a CLEAN space!
Here is the video:
Link to screen protector system used in this video is here: http://www.caseen.com/caseen-2x-Goo...Anti-Fingerprint-Screen-Protectors_p_278.html
I'll be happy to answer any questions you guys might have
That nice, but you did it wrong.. I guess its like an Oreo cookie everyone has there own way of eating them
I would have just pealed about an inch off the top then applied it and slowly and softly pushed down as I peeled of the rest..
Cel1084 said:
That nice, but you did it wrong.. I guess its like an Oreo cookie everyone has there own way of eating them
I would have just pealed about an inch off the top then applied it and slowly and softly pushed down as I peeled of the rest..
Click to expand...
Click to collapse
Thats another way to do it ;P Both great ways IMO. The only reason I don't like that way is that too many issue with people accidentally touching the sticky part, and thereby adding oil to the installation =(.
Expert Tip: Keep scotch tape ripped and ready to go to catch any dust that may fall on the sticky portion during installaion. =].
caseenBrandon said:
Thats another way to do it ;P Both great ways IMO. The only reason I don't like that way is that too many issue with people accidentally touching the sticky part, and thereby adding oil to the installation =(.
Expert Tip: Keep scotch tape ripped and ready to go to catch any dust that may fall on the sticky portion during installaion. =].
Click to expand...
Click to collapse
They should use undusted latex gloves, and If you have access to It a heppa cirtifed Cleanroom. You can gets those dispozable clean suit at
home depot for under 20 bucks too.
Cel1084 said:
They should use undusted latex gloves, and If you have access to It a heppa cirtifed Cleanroom. You can gets those dispozable clean suit at
home depot for under 20 bucks too.
Click to expand...
Click to collapse
Haha! You know, after doing Zagg twice, I actually thought about doing it like that. All gowned up, wearing powderfree gloves and working in a BSC.
No more Zagg for me.
I always get mine wet. Helps get it down and slide a little bit to align. Also allows you to also remove any bubbles easier then a dry apply. Yes I'm talking about a dry application. A little soap helps too to prevent fingerprints.
Yea like oreos.
Sent from my Nexus 7 using xda premium
That installation video was brutal. In my house if I turned the screen protector over like had done, it wouldve had at least 1 or 2 dust particles catch on it. The way i do it is to always try to start from the top, peel back maybe an inch worth of the 1st guard, and lay it as perfect as possible all while holding the protector downwards. Then work your way down gently, push out the leftover bubbles with a microfiber cloth and my fingernail. Lift and dab with tape when necessary if dust bubbles occur.
Sent from my Nexus 7 using Tapatalk 2
so how's the feel on this one (is there any grip while swiping)? is there any orange peel? and how well does it reduce fingerprint?
Lol once i go back to school ill have access to a real cleanroom, may have to buy a new screen protector for it. But imo that wasnt a very good installation guide seeing how there were still some noticeable bubbles. The technique was good but Thats whT people are trying to avoid haha
Sent from my SAMSUNG-SGH-I747 using Tapatalk 2
I usually ignore any dusts/bubbles at the beginning. Of course, it's nice not to get them, but my main concern at the start is lining it up properly so that it sits perfect on the screen. Once I get that sorted, I use scotch tape and lift up every corner and clean up from below (while wearing lab nitrile gloves). I've had perfect applications using this method, though it takes time. Heck, it took me an hour and a half to get it absolutely perfect and bubble/dust free application for my Galaxy Nexus! Only took about 20 minutes to get a perfect and clean application for the Nexus 7
For those wondering, any bubbles on the screen protector will "dry out" after 24 hours [Ours is now bubble free after 24 hours of waiting]. I can understand wanting to do more! The more techniques performed the better. Just be ready to multi-task =).
NoTnERb said:
so how's the feel on this one (is there any grip while swiping)? is there any orange peel? and how well does it reduce fingerprint?
Click to expand...
Click to collapse
As a dry system there will be no noticeable orange peel. Also this one is super smooth, and does not grip your finger at all.
You won't need to wipe your screen for 2 weeks or more guaranteed. Our GLARESHATTER system takes care of fingerprints extremely well!
We have great Amazon reviews for our Nook Color version: http://www.amazon.com/caseen-GLARES...ie=UTF8&qid=1344896005&sr=8-9&keywords=caseen
You will like the Nexus 7 one =].

XOskin screen protector

I finally installed the XOskin screen protector I got a while back.
It's been 17 hours since I installed it, about six hours in front of a heater register. I must have a hundred air bubbles! Doesn't look much different from this morning "before" a majority of the heated time. They say the micro bubbles go away in 24-48hrs. Don't know I'd call them micro bubbles and we'll see about them going away too.
Should get that guy that installed one in their video but he probably done a bunch. He had hardly any bubbles after installing it.
It's cut close near the speakers, top/bottom have some extra room but holes from the camera/sensor are tight. It took me three tries to get it right.
I put a Zagg on a 7" tab and don't remember this many bubbles. Maybe bigger doesn't mean easier?
wptski said:
I finally installed the XOskin screen protector I got a while back.
It's been 17 hours since I installed it, about six hours in front of a heater register. I must have a hundred air bubbles! Doesn't look much different from this morning "before" a majority of the heated time. They say the micro bubbles go away in 24-48hrs. Don't know I'd call them micro bubbles and we'll see about them going away too.
Should get that guy that installed one in their video but he probably done a bunch. He had hardly any bubbles after installing it.
It's cut close near the speakers, top/bottom have some extra room but holes from the camera/sensor are tight. It took me three tries to get it right.
I put a Zagg on a 7" tab and don't remember this many bubbles. Maybe bigger doesn't mean easier?
Click to expand...
Click to collapse
I installed Zaggs when I worked at Best Buy and was the go to guy there so I am going to see if I can explain this here and it might help some people out. (This is not me bragging, this is me trying to give back in whatever way I can)
First make sure you are using a clean surface and the air quality is pretty good (no dust floating around)
Next clean the screen with at least water, the spray included with Zagg and XO are actually pretty good cleaners too. You will need the cloth that comes with it to wipe it down later so use something like an extra microfiber cloth to clean it when it is wet.
Beat out the cloth that came with it against something. It will have dust in it, you need to get all that dust out. Wipe the dry screen down very well, make sure to end it you wipe all in one direction making sure there is no dust on the screen. I've found that if you start at the top and wipe towards yourself you will end up with no dust.
Spray the screen with the spray included while covering the holes that are showing on the front as you spray by them with that screen protector.
Spray the top of the screen protector (makes it easier for the squeegee to slide across and remove bubbles), and spray your fingers. (important step, saves so much grief later caused by finger prints or by trying really hard not to touch the back.)
Remove the protective backing making sure not to let any of the protector touch itself, that is a major problem with people trying their first time. Then spray the back of the protector generously and your fingers again.
Put the protector down and get it lined up. It will slide around pretty easily. When it is in line use the squeegee and make a line across the middle of the protector to hold it down.
Pull up half of it making sure not to go all the way to where you pressed it down and spray the screen and protector to make sure they are still wet and slowly squeegee it down. Start with the part touching the screen and squeegee, only laying down what the squeegee is pressing down. This will ensure that you don't create a bubble by just laying it down.
Pull up the other half to where you stopped the last time and repeat the last step with the other half.
You might end up with some liquid left in the protector, but the squeegee will get this out easily. Make sure you look at it from all angles with light hitting all sides so that you can see all the pockets. Squeegee out what remains and you are done.
It seems like a ton of work, but I consistently showed people up with this method. After putting enough down you just lay it and get it in line and squeegee the crap out of it, but this is the best way to learn. Remember that you will need some decent force to make sure you get it tight to the screen. Don't use too much though or you'll stretch it.
wptski said:
I finally installed the XOskin screen protector I got a while back.
It's been 17 hours since I installed it, about six hours in front of a heater register. I must have a hundred air bubbles! Doesn't look much different from this morning "before" a majority of the heated time. They say the micro bubbles go away in 24-48hrs. Don't know I'd call them micro bubbles and we'll see about them going away too.
Should get that guy that installed one in their video but he probably done a bunch. He had hardly any bubbles after installing it.
It's cut close near the speakers, top/bottom have some extra room but holes from the camera/sensor are tight. It took me three tries to get it right.
I put a Zagg on a 7" tab and don't remember this many bubbles. Maybe bigger doesn't mean easier?
Click to expand...
Click to collapse
are you sure you clean your screen perfectly before you apply it?
it might need longer time, like 24 hours - 48 hours, but it shouldn't that much bubble for 17 hours.
I apply the xoskin on my nexus 7 and end up with 1 bubble after about 24 hours or more, most probably because i didn't clean it well. Oh but well, the xoskin on my nexus 7 definitely reduce the sensitivity and sometimes makes the screen almost totally not responsive (i always gotta wipe the screen with something and it finally fixed). Might be the defect in my case but i don't wanna take a chance in their product again for now.
I used Monster screen cleaner with a micro fiber cloth, no cloth comes with the XOskin. One thing, it kind-of stuck and didn't slide around like the Zagg did. I wet it good on both sides but maybe because it took three tries, I should have rewet it??
In front of the heat register all day, no drastic change that I can tell and coming up on 24 hrs.
wptski said:
I used Monster screen cleaner with a micro fiber cloth, no cloth comes with the XOskin. One thing, it kind-of stuck and didn't slide around like the Zagg did. I wet it good on both sides but maybe because it took three tries, I should have rewet it??
In front of the heat register all day, no drastic change that I can tell and coming up on 24 hrs.
Click to expand...
Click to collapse
Yea, you have to rewet it when you reapply it. I would request a replacement from XO. I wouldn't put it in front of a heater either. If you squeegee it down good enough you don't need heat.
thacounty said:
Yea, you have to rewet it when you reapply it. I would request a replacement from XO. I wouldn't put it in front of a heater either. If you squeegee it down good enough you don't need heat.
Click to expand...
Click to collapse
I mean that I didn't have it completely laid down all way, I was off location a mile. You have to position by the camera/sensor holes and the top edge and there isn't much room for error. Sideways there is no room for error, overlap near the speakers and its edge will stick up.
I found the follow at the XOskin site:
How do I get rid of bubbles that appear after I’ve installed my XO Skins?
If it was recently that you installed the XO Skins, as soon as possible try pressing out the bubbles lightly with the squeegee. Make sure the squeegee is wet to avoid burn marks on the Skin. If the Skin has been dry for longer than a few hours, then the large bubbles are set in and you'll need a replacement. Small bubbles, or mini-bubbles, are normal and will disappear 24 to 48 hours after installation.
Whoops! I wonder what they call large and /or small bubbles? I removed it, wet applied to the sheet it came on on a flat surface. We'll see how it looks after a while and if it's worth a retry. Might have to get a replacement.
Like I mention, even when wet, it doesn't slide around easily. Maybe these are not as easy as a Zagg to install which has an orange peel surface which would allow the fluid in the pockets for easier movement?
wptski said:
I mean that I didn't have it completely laid down all way, I was off location a mile. You have to position by the camera/sensor holes and the top edge and there isn't much room for error. Sideways there is no room for error, overlap near the speakers and its edge will stick up.
I found the follow at the XOskin site:
How do I get rid of bubbles that appear after I’ve installed my XO Skins?
If it was recently that you installed the XO Skins, as soon as possible try pressing out the bubbles lightly with the squeegee. Make sure the squeegee is wet to avoid burn marks on the Skin. If the Skin has been dry for longer than a few hours, then the large bubbles are set in and you'll need a replacement. Small bubbles, or mini-bubbles, are normal and will disappear 24 to 48 hours after installation.
Whoops! I wonder what they call large and /or small bubbles? I removed it, wet applied to the sheet it came on on a flat surface. We'll see how it looks after a while and if it's worth a retry. Might have to get a replacement.
Like I mention, even when wet, it doesn't slide around easily. Maybe these are not as easy as a Zagg to install which has an orange peel surface which would allow the fluid in the pockets for easier movement?
Click to expand...
Click to collapse
I put xo skins on my evo 3d and my 2 touchpads when I had them. They don't slide as easily, you are correct, but keeping them wet will go a long way. That is why so much spray is included. Just make sure all bubbles are gone before you start letting it dry.
thacounty said:
I put xo skins on my evo 3d and my 2 touchpads when I had them. They don't slide as easily, you are correct, but keeping them wet will go a long way. That is why so much spray is included. Just make sure all bubbles are gone before you start letting it dry.
Click to expand...
Click to collapse
Too bad I didn't have /get more info before the first try. Yeah it probably needs lots of spray to let it slide but one has to be careful because of the speakers on the sides.
wptski said:
Too bad I didn't have /get more info before the first try. Yeah it probably needs lots of spray to let it slide but one has to be careful because of the speakers on the sides.
Click to expand...
Click to collapse
Yea, if you get liquid around them dry them out immediately. That's why I cover ports as I spray around them with the protector.

Removing Scratches from Display

It appears that I have a small scratch in the upper left portion of my display. I am unsure if I caused this (no drops) or if it came with a scratch (highly unlikely), either way though it's there.
I didn't think it would be enough of a reason to warrant an exchange, so I was wondering if you guys knew of any tips or tricks to fix the scratch. It's only visible at certain times and you can slightly feel it when running your fingernail or s pen across it.
Any help would be greatly appreciated! I have T-Mobile Jump, so I might check to see how the warranty covers it.
If you cant feel them with finger nail, use some high quality polishing compound and buffing wheel on dremel. If scrath is little deeper, you will need to do some fine wet sanding with 2000 or higher sand paper. Make sure you mask everything very well. Another option is to put screen protector and it may hide fine scratches.
Sent from my SM-N910T using XDA Free mobile app
I have a scratch on mine also..actually if u include the really fine micro scratches that u can see with bright light,then i have quite a few,noticed 2 hrs after I got home with phone on launch day,don't how they got there,tmobile store were I got phone was really rude to me about exchanging it and told me it wasn't like that when I left,so...I've been stuck with it, put screen protector on it hides some of it but have one pretty deep one that u can see all the time,luckily it's only a couple of mm long..sorry for long rant,but had to vent,lol phone was in box till I got home and put screen protector on,that's when I noticed it..grr...

Whitestone Dome disaster!

I need to vent, I'm so pissed off. Back in January I got a Whitestone Dome when they were on sale. I was happy with my plastic protector at the time, so I didn't install it right away. Fast forward to last night...
I watched a solid dozen Note8 install videos on YouTube, have been reading for months on reddit and xda all the other threads, and executed my installation perfectly according to the directions. I even taped off the earpiece just in case. Not to brag, but I'm usually really good with this sort of stuff. It ended in disaster due to the poor quality control of this product and its company.
I have read quite a few horror stories on social media about Whitestone's products, but I assumed if I was very careful I could do a successful install. WRONG. The supplied vial of glue was way too much, and after perfectly applying the glue and dropping the glass on top, capillary action pulled the glue nicely across the screen and I was very pleased. It looked beautiful. After waiting the full 15 seconds top and 15 seconds bottom, I removed my Note8 from the tray as instructed. To my horror, TONS of liquid excess glue was dripping down the sides. My S-Pen was DRIPPING with glue! There was glue everywhere, even in the bottom of the plastic jig. AND THE SCREEN WAS STILL LOOSE! After trying my best to clean up that huge mess, I followed the instructions to do the "secondary" cure. AFTER MULTIPLE MINUTES UNDER THE SUPPLIED UV LIGHT, THE GLUE IS STILL WET! My phone STINKS of this chemical, and every crevice of it is oozing this glue that will not cure under the UV light. I was meticulous about everything, there is nothing I did wrong. And besides WHY WON'T THE GLUE FULLY CURE UNDER UV!? I used the supplied USB cable, and a powerful Samsung USB wall charger so I know the light isn't "weak." I will admit that the screen has stopped moving around as of today, so something has sorta cured. But the edges are still wet, and leave an oily residue when touched, and look furry because there is so much tacky, sticky residue still oozing out.
What a horrible mess. It took me hours to clean everything up, and there is still glue in every tiny crevice of my Note8. I hope I got my S-Pen out and wiped off in time - it's still working, for now.
Always take your S-Pen out first!
ffolkes said:
I need to vent, I'm so pissed off. Back in January I got a Whitestone Dome when they were on sale. I was happy with my plastic protector at the time, so I didn't install it right away. Fast forward to last night...
I watched a solid dozen Note8 install videos on YouTube, have been reading for months on reddit and xda all the other threads, and executed my installation perfectly according to the directions. I even taped off the earpiece just in case. Not to brag, but I'm usually really good with this sort of stuff. It ended in disaster due to the poor quality control of this product and its company.
I have read quite a few horror stories on social media about Whitestone's products, but I assumed if I was very careful I could do a successful install. WRONG. The supplied vial of glue was way too much, and after perfectly applying the glue and dropping the glass on top, capillary action pulled the glue nicely across the screen and I was very pleased. It looked beautiful. After waiting the full 15 seconds top and 15 seconds bottom, I removed my Note8 from the tray as instructed. To my horror, TONS of liquid excess glue was dripping down the sides. My S-Pen was DRIPPING with glue! There was glue everywhere, even in the bottom of the plastic jig. AND THE SCREEN WAS STILL LOOSE! After trying my best to clean up that huge mess, I followed the instructions to do the "secondary" cure. AFTER MULTIPLE MINUTES UNDER THE SUPPLIED UV LIGHT, THE GLUE IS STILL WET! My phone STINKS of this chemical, and every crevice of it is oozing this glue that will not cure under the UV light. I was meticulous about everything, there is nothing I did wrong. And besides WHY WON'T THE GLUE FULLY CURE UNDER UV!? I used the supplied USB cable, and a powerful Samsung USB wall charger so I know the light isn't "weak." I will admit that the screen has stopped moving around as of today, so something has sorta cured. But the edges are still wet, and leave an oily residue when touched, and look furry because there is so much tacky, sticky residue still oozing out.
What a horrible mess. It took me hours to clean everything up, and there is still glue in every tiny crevice of my Note8. I hope I got my S-Pen out and wiped off in time - it's still working, for now.
Always take your S-Pen out first!
Click to expand...
Click to collapse
My s-pen was in the whole time too, nothing got in mine so not sure why it did with yours. You're right though, even with the tape/sponges the glue still goes everywhere. I cured it a little before moving it, and that did help keep the screen in place. Then I cured a little more afterwards and let it sit for a while... You can just carefully rinse/wash off the excess glue after. End result was good in my case, but the process can definitely be a messy experience.
sefrcoko said:
My s-pen was in the whole time too, nothing got in mine so not sure why it did with yours. You're right though, even with the tape/sponges the glue still goes everywhere. I cured it a little before moving it, and that did help keep the screen in place. Then I cured a little more afterwards and let it sit for a while... You can just carefully rinse/wash off the excess glue after. End result was good in my case, but the process can definitely be a messy experience.
Click to expand...
Click to collapse
I know I read you can wash it off somewhere else, but I thought it was oily. Is it really water soluble? I feel like bathing my phone is only going to make things worse right now haha.
ffolkes said:
I know I read you can wash it off somewhere else, but I thought it was oily. Is it really water soluble? I feel like bathing my phone is only going to make things worse right now haha.
Click to expand...
Click to collapse
It definitely feels oily, but I didn't end up having too much trouble getting it off in the end. I just ran the faucet and used my hand to wipe away what I could, rinsed hand, and repeated. Maybe a drop of hand soap at the worst, but I don't remember now. Never put the phone directly under water though...why tempt fate .Thankfully I don't have to do that more often lol
ffolkes said:
I need to vent, I'm so pissed off. Back in January I got a Whitestone Dome when they were on sale. I was happy with my plastic protector at the time, so I didn't install it right away. Fast forward to last night...
I watched a solid dozen Note8 install videos on YouTube, have been reading for months on reddit and xda all the other threads, and executed my installation perfectly according to the directions. I even taped off the earpiece just in case. Not to brag, but I'm usually really good with this sort of stuff. It ended in disaster due to the poor quality control of this product and its company.
I have read quite a few horror stories on social media about Whitestone's products, but I assumed if I was very careful I could do a successful install. WRONG. The supplied vial of glue was way too much, and after perfectly applying the glue and dropping the glass on top, capillary action pulled the glue nicely across the screen and I was very pleased. It looked beautiful. After waiting the full 15 seconds top and 15 seconds bottom, I removed my Note8 from the tray as instructed. To my horror, TONS of liquid excess glue was dripping down the sides. My S-Pen was DRIPPING with glue! There was glue everywhere, even in the bottom of the plastic jig. AND THE SCREEN WAS STILL LOOSE! After trying my best to clean up that huge mess, I followed the instructions to do the "secondary" cure. AFTER MULTIPLE MINUTES UNDER THE SUPPLIED UV LIGHT, THE GLUE IS STILL WET! My phone STINKS of this chemical, and every crevice of it is oozing this glue that will not cure under the UV light. I was meticulous about everything, there is nothing I did wrong. And besides WHY WON'T THE GLUE FULLY CURE UNDER UV!? I used the supplied USB cable, and a powerful Samsung USB wall charger so I know the light isn't "weak." I will admit that the screen has stopped moving around as of today, so something has sorta cured. But the edges are still wet, and leave an oily residue when touched, and look furry because there is so much tacky, sticky residue still oozing out.
What a horrible mess. It took me hours to clean everything up, and there is still glue in every tiny crevice of my Note8. I hope I got my S-Pen out and wiped off in time - it's still working, for now.
Always take your S-Pen out first!
Click to expand...
Click to collapse
What a nightmare. I fear using glue that might run down and block all my holes and crevices LOL.
Sent from my SM-N950U using Tapatalk
I had this issue when I was installing the Whitestone Dome on my S8+.
The sides and back of the phone were dripping with the greasy ass glue.
However, I've had no issues since with my Note 8.
I would like to add that when i was applying it to the S8+ I don't think the surface was entirely flat- the tip I saw was to use the glue vials and put them on the table to see if they'd roll; I did this until I had a perfectly level table.
I managed to install the protector flawlessly on my Note 8 without any issues.
I'm sure if you contact Whitestone they'll be able to provide you with another vial if you've used both.
Are you certain that the screen was dry before you applied it?
Definitely not trying to be contradictory
But for my Note 8 the install was easy, no mess, no problems...... Went just like instructions
S-Pen still works, and I must say the glass looks fantastic. Edges aren't great, but I vigorously rubbed the sides in one direction with a cloth. Over and over, until eventually the ragged glue on the edges sorta wiped away. I'm sure there will be problems down the road, but it's good for now at least. I also used some scraps of tape to try to remove the excess tacky glue that didn't wipe away. Just have to remember to use 1/3 less glue next time. Maybe remove the vial right after removing the second cap, rather than waiting for it to completely empty out.
ive replace my whitestone twice already. never any issue with the install. I wish the glass was stronger though. First crack was a legit saved my phone. someone bumped me on accident and screen down onto a bunch of pebbles. left junks missing from the protector but totally safe screen. last one was fell of my bed and chipped of the whole top edges and a nice crack across. but.... still saved the phone so i'm loyal
I hate to necro this thread considering its two years old but I just had the same painful experience on my Note 10+ 5G LOCA somehow managed to leak into my SPen slot. If you're thinking of buying this screen protector. Don't. You're better off with nothing.
Edit: After re-registering my fingerprints for the 3rd time it is working much faster and the SPen has seemed to loosen up after repeatedly taking it out and putting it back in and now appears to charge just fine.

Categories

Resources