Hi,
I've just reflashed with the new UK TMobile ROM, and since then I'm having trouble using active-sync at work, I know the problem is caused by the sygate personal firewall config, but I can't change that because of company rules.
When I had the Mr Clean 2.2.4 rom installed it had a panel in the settings screen to change the USB configuration to use a different type of connection.
This worked fine.
At some point in the past I also had some registry tweaks which changed some networking parameters and that made it work fine too, I can't remember if they were on the device or on my PC.
Anyone out there remember the settings or know where I can get a .cab of that usb configuration tool?
Adam
Re: Active Sync with new TMOBILE UK rom and Sygate Firewall
adam_xda said:
Hi,
I've just reflashed with the new UK TMobile ROM, and since then I'm having trouble using active-sync at work, I know the problem is caused by the sygate personal firewall config, but I can't change that because of company rules.
When I had the Mr Clean 2.2.4 rom installed it had a panel in the settings screen to change the USB configuration to use a different type of connection.
This worked fine.
At some point in the past I also had some registry tweaks which changed some networking parameters and that made it work fine too, I can't remember if they were on the device or on my PC.
Anyone out there remember the settings or know where I can get a .cab of that usb configuration tool?
Adam
Click to expand...
Click to collapse
If your device uses Windows Mobile 5 you must open some ports in the sygate firewall settings: http://www.microsoft.com/windowsmobile/help/activesync/sygate.mspx.
Also it's necessary to change the RNDIS driver settings in the mobile phones registry as well!
Use a regedit tool like PHM Registry Editor.
Here are the settings to be added (or to be changed respectively):
Key: HKEY_LOCAL_MACHINE\Drivers\USB\FunctionDrivers\RNDIS
Name of the Value to add: MTU
Type : DWORD
Data: 1514 (Value is Decimal)
Name of Value to add: MaxOutTransfer
Type: DWORD
Data: 1642 (Value is Decimal)
After a reset my Prophet (XDA Neo) synchronized well with active sygate firewall!
Anyone managed to get Foxtel (or even Telstra My Place) working on a Kaiser / Tytn II?
I've attempted to install Default_i-mate_MyPlace.cab (with or without Telstra_V5.5.CAB) from http://forum.xda-developers.com/showpost.php?p=1719900&postcount=63 but it fails to install, reporting nothing other than "Installation was unsuccessful".
I've tried this straight after a factory reset too. The ROM is the default one it shipped with - 1.82.707.0 WWE (11/03/2007)
From what I've seen posted by others, it 'should' be as simple as installing the MyPlace cab then changing a registry setting, but I'm not having any luck with even the first part!
Anyone run into similar problems, or able to assist?
prk.
telstra cab
If you install the latest Telstra ROM then use schaps utility to unlock the extended ROM and copy the contensts somewhere you can then install the TELSTRA 5.5 cab. You will probably also need another cab called Default_Imate_AUS_HR_V3.60.00.cab. I have SCHAPS 4.01 FULL with both of them installed and everything is fine. Contrary to some threads I have flashed heaps opf ROMS and I love my JASJAM, being a tech nerd of course.
Finally got Foxtel working on my Kaiser (Tytn II) with Telstra NextG.
The main problem I ran into was when downloading the files from http://forum.xda-developers.com/showpost.php?p=1719900&postcount=63 I was right clicking and selecting "save as". This doesn't work, as the link heads off to Rapid share, where you have to click free, then wait a while, etc. Silly me.
In case anyone's interested (or for the next time I reset):
1) Install the Default_i-mate_MyPlace.cab (approx 70k)
This gives the "My Place" option in the Programs list. When I ran it and tried to go to any of the options, it would connect, then timeout on finding location.
2) Ensure the Telstra Internet connection is using a proxy:
Start / Settings / Connections / Connections
Under "Telstra Internet Settings" select "Manage existing connections"
Under Proxy Settings, tick "This network uses a proxy server ..."
Advanced / HTTP
Set server to "10.1.1.181" and port to 80
Okay out.
At this stage I could now go to the various locations in Telstra My Place. Except Foxtel which gave an error about not having a compatible phone.
3) Change the User Agent by editing the registry.
The key is \HKLM\Security\Internet Explorer\User Agent\CustomBase
I changed it from: HTC_P4550 Mozilla/4.0
to: i-mate JASJAM V2 PPC; 240x320; HTC_TyTN/1.0 Profile/MIDP-2.0 Configuration/CLDC-1.1
Now I could load the foxtel link. When I tried the free service, streaming media told me it couldn't connect.
4) Configure streaming media:
Start / Programs / Streaming Media
Menu / Options
Set "Connect Via" to "Telstra Internet Settings"
Voila - Foxtel now works.
prk.
prk said:
Finally got Foxtel working on my Kaiser (Tytn II) with Telstra NextG.
The main problem I ran into was when downloading the files from http://forum.xda-developers.com/showpost.php?p=1719900&postcount=63 I was right clicking and selecting "save as". This doesn't work, as the link heads off to Rapid share, where you have to click free, then wait a while, etc. Silly me.
In case anyone's interested (or for the next time I reset):
1) Install the Default_i-mate_MyPlace.cab (approx 70k)
This gives the "My Place" option in the Programs list. When I ran it and tried to go to any of the options, it would connect, then timeout on finding location.
2) Ensure the Telstra Internet connection is using a proxy:
Start / Settings / Connections / Connections
Under "Telstra Internet Settings" select "Manage existing connections"
Under Proxy Settings, tick "This network uses a proxy server ..."
Advanced / HTTP
Set server to "10.1.1.181" and port to 80
Okay out.
At this stage I could now go to the various locations in Telstra My Place. Except Foxtel which gave an error about not having a compatible phone.
3) Change the User Agent by editing the registry.
The key is \HKLM\Security\Internet Explorer\User Agent\CustomBase
I changed it from: HTC_P4550 Mozilla/4.0
to: i-mate JASJAM V2 PPC; 240x320; HTC_TyTN/1.0 Profile/MIDP-2.0 Configuration/CLDC-1.1
Now I could load the foxtel link. When I tried the free service, streaming media told me it couldn't connect.
4) Configure streaming media:
Start / Programs / Streaming Media
Menu / Options
Set "Connect Via" to "Telstra Internet Settings"
Voila - Foxtel now works.
prk.
Click to expand...
Click to collapse
Hi im extremely new to this stuff.and sorry for the Noob question.
I am upto the part of the registry key. I cant seem to find the registry key that i need to change it. Could you give some type of instruction on this. Ill keep searching in the mean time.
Thanks for your help
Frank
Got it going. Thanks. Had to reset unit.
Big thanks
I-Mate Cab Installation
Hi,
could anyone please tell me (or point me to a link) how to install Cabs on an I-mate 9502.
I need to access Telstra's Myplace after installing windows 6.1.
I have downloaded the appropriate cab onto my pc, and then transferred it to the storage card on the 9502, but I cannot instal it onto the 9502.
I am a beginner with the 9502, and would appreciate any help.
Many thanks
Paul
Hey it's ok. I finally worked it out!
Cheers
Pauyl
Hey Pauly,
what did you do? I just got 6.1 and am lost. I got the configurator cab (correct one?) off the imate page but little does it config. No My Page or Foxtel etc. BTW I couldn't find a My Place cab.
Teddo
Hi,
I think (better I hope) I have found a solution for the "HTC looses HTTP proxy settings for WiFi connections". Probably you have already noticed, that the HTTP proxy setting for a WiFi connection (e.g. configured using "Work" connection setup) is lost after closing and reopening the connection configuration dialog.
During my investigations I found, that the registry snapshots, shortly taken after entering the proxy and after reopening the configuration settings again, were nearly identical. There was no clue, that the configuration program itself reversed the settings, so there was a high feasibility, that the problem is either the entry or the re-read into/out of the registry.
The problem seems to be, that the configuration program does enter the proxy setup in a wrong format. Whereas the "type" parameter should be set to "1" (HTTP) the configuration setup sets this to "0" (null proxy).
So in order to reverse this one has to change the registry (e.g. using PHMRegedit) by performing the following procedure:
1) Go to
HKLM\Comm\ConnMgr\Providers\{EF097F4C-DC4B-4c98-8FF6-AEF805DC0E8E}
2) Locate your proxy setup (key starts with HTTP-{xxxxxxx})
3) Change the "type" value to "1"
For PocketIE the parameter "EnableAutoDetect" in HKCU\Software\Microsoft\Windows\CurrentVersion\Internet Settings (Note: There is no space in the key, don't know, why this forum inserts one) should be either not there (default) or set to 1.
Please double check and let me know. Keep in mind, that your settings may get lost, every time you tamper with the connection configuration program. Probably somebody could provide an OMA Provisioning CAB (_Setup.xml with CM_ProxyEntries and stuff).
EDIT: CAB attached. The contained _Setup.xml connects WORK (SrcID) with WiFi (DestId) using the specified proxy. Taylor it to your needs. Don't forget to "makecab /D COMPRESS=OFF _setup.xml ProxyOn.cab" (Note: COMPRESS=OFF) and ActiveSync it to your device. Tap it to "install". Save the cab for other uses.
EDIT II: Registry key fixed...sorry....
Regards
Neil
i hope this works, ill give it a go when i have time.
It works - great.
Thank you
Andre
I tried the proposed solution, using the .cab file and also by hand, without success.
My regietry key defining the proxy has type=1, but still does not connect...
Sorry, It works when conneting through activesync, but not through wifi.
Does anybody know where is the "intelligence" that decides which connection to use? Is it in the registry?
You have to ensure:
a) Your WiFi board connects to Work, not to Internet
b) Both connection setups must point to Work
The providec cab connects Wifi with Work and configures the proxy.
Hi, neil,
Thanks for the quick response. I did check that the card points to Work, and both connection set ups point to my work network. When editing the connections, I can see that the proxy is well defined. If I enter the registry, I can also see the proxy definition and "enable=1", "type=1". But still PIE hangs in "locating..."
Now, I run the .cab file with wifi "on"...
Probably something is wrong with your proxy. Fortunately I have a transparent proxy up and running. 141.39.43.185 port 8080. Try it. I'll see you
BTW: Sometimes a softreset does make wonders...
Regards
Ah, and don't forget: Whenever you open your devices proxy configuration and closes it again, the proxy config is messed up again by HTC.
Regards
Will try and provide feedback, but, What do you mean by try the transparent proxy? Shoul i define that proxy?
I din know about soft resets. I have even done a hard reset so I am now traying with a fresh registry... Have not ASed yet. But I wonder, Is there a key in the registry that defines which are the correct connections? Or is it all done via SrcId and DestId?
One more thing. I tried to change the proxy definition in your cab file. Extracted the setup, changed it and winrared it back... but this new cab will not install. My proxy is 192.168.0.254:8080...
Sorry for beeing not specific enough: Yes, please define that proxy. Transparent was meant in the sense of "does nothing than transfer back and forth"
Concerning repacking: Use makecab not rar. And don't compress.
SrcID and DestID makes the thing. This GUIDs haven't changed since the very first version of WM
Regards
Tryied my own cab file and worked... only once. It's lost again. Soft reset and will recheck. Thanks for the support
I can not make it connect anymore.
I run the cab file without success. What should the sequence be?
1.- set both connections to "my work network"
2.- open PIE
3.- run the cab file?
In Mobile 6.1 the settings stays but PIE doesn't use the the proxy configuration for some reason.
I'm experimenting with this. Making progress. But I'm still having some difficulty.
I think my Socks proxy port is not getting set right. I'll post back how it is going, but does anyone have thought about the Socks?
[EDIT]
Well, I had hooked up once (or maybe it was reading cache).
Anyway, I'm not having luck. It looks like the settings are right.
One thing I do notice, is that the WAP one, the Type is 2, and the Socks the type is 4, if that makes any difference. But the type for the HTTP one is 1, and the setting for IE looks correct to.
ewingr said:
I'm experimenting with this. Making progress. But I'm still having some difficulty.
I think my Socks proxy port is not getting set right. I'll post back how it is going, but does anyone have thought about the Socks?
[EDIT]
Well, I had hooked up once (or maybe it was reading cache).
Anyway, I'm not having luck. It looks like the settings are right.
One thing I do notice, is that the WAP one, the Type is 2, and the Socks the type is 4, if that makes any difference. But the type for the HTTP one is 1, and the setting for IE looks correct to.
Click to expand...
Click to collapse
With the downloaded cab, extract the file (may use winrar), change it to your liking and makecab again (no compression).
neil.young said:
Hi,
I think (better I hope) I have found a solution for the "HTC looses HTTP proxy settings for WiFi connections". Probably you have already noticed, that the HTTP proxy setting for a WiFi connection (e.g. configured using "Work" connection setup) is lost after closing and reopening the connection configuration dialog.
During my investigations I found, that the registry snapshots, shortly taken after entering the proxy and after reopening the configuration settings again, were nearly identical. There was no clue, that the configuration program itself reversed the settings, so there was a high feasibility, that the problem is either the entry or the re-read into/out of the registry.
The problem seems to be, that the configuration program does enter the proxy setup in a wrong format. Whereas the "type" parameter should be set to "1" (HTTP) the configuration setup sets this to "0" (null proxy).
So in order to reverse this one has to change the registry (e.g. using PHMRegedit) by performing the following procedure:
1) Go to
HKLM\Comm\ConnMgr\Providers\{EF097F4C-DC4B-4c98-8FF6-AEF805DC0E8E}
2) Locate your proxy setup (key starts with HTTP-{xxxxxxx})
3) Change the "type" value to "1"
For PocketIE the parameter "EnableAutoDetect" in HKCU\Software\Microsoft\Windows\CurrentVersion\Internet Settings (Note: There is no space in the key, don't know, why this forum inserts one) should be either not there (default) or set to 1.
Please double check and let me know. Keep in mind, that your settings may get lost, every time you tamper with the connection configuration program. Probably somebody could provide an OMA Provisioning CAB (_Setup.xml with CM_ProxyEntries and stuff).
EDIT: CAB attached. The contained _Setup.xml connects WORK (SrcID) with WiFi (DestId) using the specified proxy. Taylor it to your needs. Don't forget to "makecab /D COMPRESS=OFF _setup.xml ProxyOn.cab" (Note: COMPRESS=OFF) and ActiveSync it to your device. Tap it to "install". Save the cab for other uses.
EDIT II: Registry key fixed...sorry....
Regards
Neil
Click to expand...
Click to collapse
Hi, Neil
Have you noticed the key "Modified"? If no wifi network is selected, this key seems to be "0", but when a wifi network is connected, it changes to "1"...
javes said:
With the downloaded cab, extract the file (may use winrar), change it to your liking and makecab again (no compression).
Click to expand...
Click to collapse
Hi Javes
That is what I'm doing. The only mod I made to the file was I changed the Proxy address to the DNS name of our proxy here at work.
What I"m finding is that the key is going in with Type set to 0, even though the XML file has 1 in it.
I'm also noticing that there is another HTTP characteristic with my Proxy (I'm guessing likely from setting in Conn Manager, with my Proxy, and a type of 0, so I have manually set both it and the one added by XML to a type of 1.
After that, still does not connect. I soft reset, and they are back to 0.
So, I went into Connection manager, and deleted references to Proxy,and turned off Proxy, and ran DClicked the Proxy cab again. The settings went in with 1, doesn't connect, and I get a popup that says "Cannot connect with current connectin settings"
So, I soft reset again, and it's back to 0.
So I went into connections, set Proxy to ON, but no proxy settings. Ran the XML file, still no connection.
I think I have a gremlin that won't let mu connect on the public at work. Interestingly, one day a copule weeks ago I was successful connecting...until a soft reset later that day. I had set EVERY item with my work Proxy: HTTP, WAP, SOCKS, and SECURE WAP.
ewingr,
I am no expert at all and have no solutions. Like you, I followed the original instructions about the cab file, with results similar to yours. I've been able to connect on two different occasions, but these connections only last for a minute. After this minute, connection is impossible for me, with resets, re-cabs and the lot. Lets wait until someone more knowledgeable drives us to success...
In the meanwhile, I will keep trying different things.
I have a file called ATT Settings.cab which I got from this forum (somewhere, can't remember where). It is supposed to set the phone to ATT US connection settings. I have installed it (i.e. clicked on the cab file), but can't find where the icon is to start it (I'm expecting menu settings, etc.) Has anyone used this before and if so where do I look to run this program?
I haven't used this cab before, but I have to assume all it does is automatically enter the browser settings. Like the ones you would find here. You won't find an installed program for you to run.
it's automatically installed.
its not an application, it changes settings. some roms it may be just install the cab and your good to go, but in others such as L26 diamond you have to go settings>connections(tab)>connections(icon)>advanced(tab)> select networks> change both to mediaNet then edit>proxy settings> uncheck this network uses a proxy server...
fjc3 said:
its not an application, it changes settings. some roms it may be just install the cab and your good to go, but in others such as L26 diamond you have to go settings>connections(tab)>connections(icon)>advanced(tab)> select networks> change both to mediaNet then edit>proxy settings> uncheck this network uses a proxy server...
Click to expand...
Click to collapse
well after you install att settings cab and follow these operations you may as well install removehiddenproxy.cab because attsettings.cab doesn't remove the hidden proxy. The hidden proxy can prevent you from downloading quickgps, htc weather updates, and a few other things.
Okay, i just flashed RomeoS 4.1 onto my AT&T tilt. How do I get my 3g data connection back? I can use my LAN WIFI to go on the interent, but not the 3g line. There has got to be something simple I am missing! help
Did you run "Connection Setup".
I don't have RomeoS ROM, but it should be here:
Start>Settings>
>Connections Tab
>Connection Setup
run that and it should set up the correct settings for your network.
The other thing you may need to do is:
in the same place as the "Connections Setup" there should be a "Connections" Icon.
>Connections
>Manage existing connections
>Proxy Settings
>make sure "this network uses a proxy server to connect to the internet" option is UNCHECKED.
I hope that does the trick for you. It the only thing I can think of.
Run HTC Connection setup and DISABLE proxy
thanks for your suggestions, i will try this today!
still doesn't seem to work. I would assume that every single time anyone flashes a new rom, they have to setup their data connection again, right?
It'll work for sure, as suggested above, use Network Wizard or the HTC Connection tool, both do the same thing and the cabs area available on XDA-Dev.
And yes if you re-flash your ROM you'll need to set your Data Connection settings again as they are formatted when you ROM upgrade.
I had the same issue when i installed that rom, theres a cab called Cingular PDA Medianet mms and one called wpbear_AT&T_proxy there on this site if i wasent on my phone i would link you
wpbear_AT&T_proxy
Click to expand...
Click to collapse
Don't like it... however pending on your flash history and what you installed you may have to check a reg entry
[HKEY_LOCAL_MACHINE \SOFTWARE \HTC \CommManager \WLAN] = " \\ Windows \\ WLanMgr.exe " "DeviceName" = " {98C5250D-C29A-4985-AE5F-AFE5367E5006} \\ TNETW12511 "
If it reads TNETW12511 you're OK
downloading those cabs worked like a charm! thank you very much!