Related
Hi..huge problem here...
..I've been uisng Faria for about a week....very nice ROM...but yesterday i installed CheckNotification (for deleting old/duplicate niotifications..) and my AS stop working...
I tried mayn things from this forum..from switching to "COM connection" with USB switch, unchekd/checked USB to PC option....but nothing help.
When i cradle my Qtek 9100, ActiveSync detect phone...and status Synchronizing is in ActiveSync........but when it gotta be synchroniezd there is an error : ActiveSync cannot connect to the Windows Mobile Device...
I've even tried switch to USB mode (softreset+rec button) to make new ROM install from beginig, but I can't...i get error... ERROR 260 Update Error.
I'm not shure that CheckNotification software is guilty for all that..buw, before it's installation everything worked OK.
I noticed a few things..
when i cradle phone and my ActiveSync is in status Synchornizing...there is no sync sign on ma PDA in Start line as usually
my Contacts dissapeard
my Tasks/Appointments dissapeard..
I hope...i didnt' fuc*** up my PDA.
Any help? Please.....
Thank U very much!
Luka
akulp said:
Hi..huge problem here...
..I've been uisng Faria for about a week....very nice ROM...but yesterday i installed CheckNotification (for deleting old/duplicate niotifications..) and my AS stop working...
I tried mayn things from this forum..from switching to "COM connection" with USB switch, unchekd/checked USB to PC option....but nothing help.
When i cradle my Qtek 9100, ActiveSync detect phone...and status Synchronizing is in ActiveSync........but when it gotta be synchroniezd there is an error : ActiveSync cannot connect to the Windows Mobile Device...
I've even tried switch to USB mode (softreset+rec button) to make new ROM install from beginig, but I can't...i get error... ERROR 260 Update Error.
I'm not shure that CheckNotification software is guilty for all that..buw, before it's installation everything worked OK.
I noticed a few things..
when i cradle phone and my ActiveSync is in status Synchornizing...there is no sync sign on ma PDA in Start line as usually
my Contacts dissapeard
my Tasks/Appointments dissapeard..
I hope...i didnt' fuc*** up my PDA.
Any help? Please.....
Thank U very much!
Luka
Click to expand...
Click to collapse
i had the same problem and i did the following and solved the problem:
1. uninstall outlook (2003 or 2007 or other)
2. uninstall active sync
and after that reset computer and hen install
1. outlokk
2. install activesync
and u r donw. U can backup outlook files or sync again !! but it will solve the problem because sometimes he active sync misses up with exchange seerver and doing the following steps will solve the problems !!
I already tried that...i even trie updating from bootloader from other comp...but nothing....can I update ROM from SD?..and how ?
Hi,
i have upgraded to WM6 to Tofclock's version and all was fine, now i cannot sync with either of my PC's running XP and Vista. i get a "device not recoginsed" error message and my Himalaya has locked up?? is there another way of going back to WM2003 ?
any help would be greatly appreicated.
You have a activesync 4.5 ???
problems!!
i am using active sync on my laptop running XP and i've tried windows mobile device center on my PC running Vista. if i thought it would work i'd hook up my himalaya to my Wii..... ?
try going to settings>connections>USB to PC and enable the option if it isnt n if it is try disabling it.
make sure u are connecting ur USB cable directly to ur PC not via a hub..also make sure if ur Connector is soldered in the right place..maybe its broken or moving..some times i also get this type of error..try to softreset also and restart ur windows too
problems !!
thanks guys all sorted, it was the "usb to pc" link that was unticked.
thanks again
My Blue Angel Activsyn Is Not Recognized By The Pc For A Reason I Do Not Know , Tried Many Times Hard Reset Soft Reset , Mtty Tool
Bootloader Mode Nothing Is Working If Any One Has An Idea How Can I Upgrade Or Even Re Falsh The Same Rom I Will Appreciate It Thanks
mohannad18 said:
My Blue Angel Activsyn Is Not Recognized By The Pc For A Reason I Do Not Know , Tried Many Times Hard Reset Soft Reset , Mtty Tool
Bootloader Mode Nothing Is Working If Any One Has An Idea How Can I Upgrade Or Even Re Falsh The Same Rom I Will Appreciate It Thanks
Click to expand...
Click to collapse
You MUST flash via sync, there is no method available to flash from SD card. Are you using XP or Vista? There is a known issue with Vista not liking the BA. Are you manually putting the BA into bootloader mode then placing in the cradle or trying to do it some other way? The method that works 100% for me is to manually put in bootloader mode (power+reset+record), this gives me a screen that says Serial at the top and a version number at the bottom, there is no backlight and when I then place it into the cradle Serial changes to USB. At this point on the computer run MA_Upgrade and everything should work. Keep in mind that I will never use Vista so if you are the YMMV.
will i could manually go to bootloader mode but the time i place device on cradle " unknown device" appears and running the maupgrade.exe leads to blank upgrade rom version several times i have done it ??? any suggestions
i have windows xp , activsyn 4.5 , bootloader ver 2.06
mohannad18 said:
will i could manually go to bootloader mode but the time i place device on cradle " unknown device" appears and running the maupgrade.exe leads to blank upgrade rom version several times i have done it ??? any suggestions
i have windows xp , activsyn 4.5 , bootloader ver 2.06
Click to expand...
Click to collapse
As silly as this sounds, try a different USB port. Also make sure you are directly connected to the computer not via a USB hub.
tried more than one computer for connection and more than 4 ports still i got the same " usb device not recognized"
mohannad18 said:
tried more than one computer for connection and more than 4 ports still i got the same " usb device not recognized"
Click to expand...
Click to collapse
Try a different cradle/cable.
The time I had this exact problem, it turned out of be a broken wire in the data cable.
i bought another cradle still i hvae the same message " usb device is not recognised"
Hrmm... I'm going to throw out a few ideas to look at. Some probably don't apply since you tried this on another machine, per your post, but it can't hurt in regards to this issue...
Try uninstalling activesync, reboot, reinstall, reboot. The 'drivers' that are used are installed with activesync.
If you have any 3rd party USB drivers, try reinstalling them.
Disable 'advanced network functionality' on the phone
Backup your phone and hard reset
Do you have anything that monitors the USB port on the machine you are trying to do this on?
Make sure you are using activsync 4.5 or newer. Other than that and what you already read here I can think of nothing.
i have tried so many versions of activesyn 3.x-4.5 with reboot each time of installation ,advanced network diabled, still the same thing " usb device not recognized"
sorry for inconvenience what is usb moniter machine??
BA - Does the activesync (3x-4.5) - work via bluetooth 4 U/G's ?
Angel - Does the activesync's (3x-4.5) - work via bluetooth 4 U/G's?
(no cradle / no usb) , but file transfere's work ok, via BT exchange folder (paired)
for running the ====#====#===#XDATools#==#=== & the #====#====#====#special_rom_1.2.exe#==#
angel of the ph20b
1.31.00 wwe
rom 12/13/04
1.06.00FM
1337.38,
ext rom 1.31.139wwe - flavours
my BlueTooth is belkin F8T008 (belkin say it uses comm4) - (BlueAngel say it uses - in comm5 / out comm 6), & activesync4.5 says (no-way, even adding ports, then removing all under comm9 etc)
(if I could run them from midlet, from sd say )
ASK B4 U TRY ??? (101/Flash4dummies/NewbiesTube . . . .YouNube? where ()not the wiki() - Im getting to be a silver surfer, already!
followed a few tutorials, none look like my sp3, on xp-pro, I also have no outlook, etc (no excel, - NO office!), but I only came for a soft-key fix/addon = 4midlet's)
tried removing the pair'ings from regedit(then regclean). Oh and when running activesync from BA, I cannot even get a PC (discoverable 'n all devices 'n all services ect
and breathe!
Oh and any reply's would be gratefully received, B4 '2010', that is -
shame the bolt that was shot, was just too soon, so no score for the aim, though! -
usb activesync problem
usb activesync problem
ignore the previous post - cannot connect to activesync via bluetooth!
radio upgrade worked !!!!!!!!!!!!!!!!!!!!!!!!!!!
special_rom_1.2.exe, unzipped to a xdatools folder
running start.bat, after activesync's finnished sync-ing
in the dos window I get a get device error
and
error 011:execute remote comms prog error
I'm VNese, my level of Eng is poor. but I think u should check your USB port. Do u use full of usb port? may be, the power in USB port is low -> error. Or hardware(USB chip) is bad. check more
Shot in the dark but I had the same problem with a friends 6700. I found out that the antivirus/firewall/internet security suite was blocking the proper ports needed to connect. When I disabled the software for a moment, attempted a sync it would work, then I could turn the software back on and be fine. If I disconnected and reconnected it would only charge. Give that a whirl.
DESPERATELY NEED HELP.
Every time i connect my wizard to my machine using the USB cable, i get the following message in baloon.
"One of the USB Devices attached to this computer has malfunctioned, and windows does not recognize it."
It appears as "Unknonw Device" on windows device manager.
This started happening when i changed my ROM to AMP.v2.Vanilla. Prior to that my wizard was connecting fine. I have been trying to resolve this for days now but no luck.
Following are the things i have tried.
1. Un-installed Activesync & re-installed.
2. Soft & Hard Reset the device.
3. Tried going in bootloader so that i can install my preivous rom, but the machine still doesnt recognize the device and gives the same message as mentioned above.
4. Removed all the USB controllers and re-installed in the machine.
5. Tried on different machines but same results, so its not machine specific.
6. Tried with a new cable to so its not the cable, it has to be the device.
Anyone who can help with this. I am sure i am not the only one having this trouble.
Any kind of help is appreciated. Just need to connect and go back to my preivous rom.
FYI: I am running WINXP SP2 on my machine.
ROM: 10.0.0.10
Radio: 02.69.11
Protocal: 1.1.13.30
Thanks in advance.
Nick.
You can flash in bootloaders mode,its not necessary to activesync.Get you phone in Bootloaders (tri color screen) by holding down Camers button and either Soft Reset or push Power On button,it'll go into bootloaders,hook up the phone with pc via usb cable,watch small usb appear at the bottom of the bootloaders,its good to go and run the RUU in the Rom,it'll start to flash and upgrade.Solve the activesync problem afterwards.
Thanks for the reply mate but i have already tried that.
I went into the booloader and connected the usb. It does show USB at the screen, however my PC doesnt recognize it and the RUU doesnt run. It says to connect the device.
I am not at all worried abt the activesync. Syncing is the last thing i'll think. I just want to connect and go back to my previous rom.
Any other suggestions.
Please see attached screen shots.
This sounds like a hardware issue on your phone. I doubt this works but go to start -> settings -> connections -> usb-pc and either check or uncheck the box then close that app.
If that doesn't work Search for the thread on flashing from the miniSD card. But again, this sounds like the usb on your phone has failed.
I have tried checking the USB to PC and unchecking it. No help with that.
One more interesting thing is the phone does get charged with the USB cable, just doesnt connect.
Will check the thread for flashing from minisd.
Thanks bunches.
hmm,
Hard reset your phone and uncheck the option 'allow network connections' or something in the phone settings...> connections...> usb to pc
This error occurs when there is an “open port error” before upgrading ,You can reset the device and run RUU again. If you still encounter an “OPEN PORT ERROR” again, reset your computer and try again. disable or stop any antivirus/firewall running or any other such program which might be hindering the flash,don't surf the net.
Kill 'WCESCOM' altogether,in the Task Manager,stopping activesync.
nick_shire said:
I have tried checking the USB to PC and unchecking it. No help with that.
One more interesting thing is the phone does get charged with the USB cable, just doesnt connect.
Will check the thread for flashing from minisd.
Thanks bunches.
Click to expand...
Click to collapse
hmmm,you got a connection problem buddy,the mini usb port of the phone is broken or damaged,you cannot flash with sdcard method,untill you already had made a backup of the rom earlier and saved it on the sdcard.
Get the mini usb port of the phone repaired or you can try to wriggle it a bit and check if it works and try to hold it there in that possition till the flash completes.
IS there a place i can get step by step process of flashing through SD card?
For all the forums, i am not able to understand anything./
Even the mtty doesnt work, it doesnt open the usb port.
No Luck as of now.....Am very desperately waiting for any Saviour....PLEASE
No other way out,except to get the freakin mini usb port repaired or replaced.
zabardast_1 said:
hmmm,you got a connection problem buddy,the mini usb port of the phone is broken or damaged,you cannot flash with sdcard method,untill you already had made a backup of the rom earlier and saved it on the sdcard.
Get the mini usb port of the phone repaired or you can try to wriggle it a bit and check if it works and try to hold it there in that possition till the flash completes.
Click to expand...
Click to collapse
Dang, thats right. I forgot that on the Wizard you can only flash a previously saved rom image. Can't just flash roms like you can on the Tilt.
Yep, basically, you have to get the USB port fixed as you are stuck where you are currently at on the Wizard I'm afraid.
Thanks guys. Have given my Wizard to get the Mini USB Port changed. I have my fingers crossed. Hope it works.
What exactly happens to the mini usb port?
I am having the same problem syncing.
The phone hooks up, charges, and makes the "connected" sound when I plug it into the usb port, but NO activesync...DOH!!!
Honestly, i couldn't figure it out.....no one seems to know whats the cause. The phone is bricked. It wont even start now... and its lying....
I am using an LG KS20 these days.....
Let me know if somebody happens to find a solution for that.
nick_shire said:
Honestly, i couldn't figure it out.....no one seems to know whats the cause. The phone is bricked. It wont even start now... and its lying....
I am using an LG KS20 these days.....
Let me know if somebody happens to find a solution for that.
Click to expand...
Click to collapse
Dear NIce_shire,
i am having the same problem and i got it resolved just by holding and tightly pressing the mini usb in my device. Its basically the problem with mini usb port of pda (Hardware) not a software one. Get it reparied from market or do it by urself. Good Luck!
USB link?
Hi mfrazzz
I have the same problem - USB link stopped working after a Radio upgrade. Definitively not a h/w USB miniport problem. Even when I get the Wizard G3 phone into bootloader and the USB word is at the bottom in the white line, flashing ROMs does not work as the RUU reports Error message stating no USB link (BTW, ActiveSync also reports no mobile device present and doesn't connect).
Is this a bricked phone then?
Thanks.
DesperateDan
PS The set is an MDA Vario and I had successfully installed S.V.I.s Manila 4.5 Beta (IPL 1.01, SPL 1.01 shows now, but was IPL 1.01, SPL 1.06 prior to installing Manila and Radio was 1.12.10 and I upgraded it to 2.69.11 and then the bloody thing stopped working and the USB link can't be enabled again)
Dear all,
I was facing the same issue of "USB device malfunctioned" and got it resolved yesterday. Its not because of software neither coz of cable (i did changed lots of cables but faced the same issue), its just because of mini USB in device. Its working perfectly alright now, it may not be replaced even dont need replacement at all. It needs minor soldering, even you can do it by urself. Just open 4 screws at its back (two under the camera cap one is below stylus placement and 4th is on opposite side) and open it. No need to be worried about......
Regards,
Barjees
Hi, I've an Ba with WM6.5 in it. But when I want to reflash it, the BA wasn't detected by my computer. I've put it into the bootloader mode, but it just shows Serial, even I've waiting for almost 2 hours. But when I boot the OS, it can connected to the PC via ActiveSync. What's going on here?? Is my BA or my cradle broken??
are you running XP if so open CTRL ALT DEL then look for wscesscom or somthing and end task and then WcessMgr OR somthing and end task and try
You should see Troubleshooting in the WIKI ~ http://forum.xda-developers.com/wiki/ActiveSync
I've done all of that, but still not working. I think it's not in the activesync, because I can connect my BA to the PC, the problem looks like in the bootloader mode.... It just standing there shows "serial" and "V2.07", even I've connect it to the USB port... Any ideas??
Is there are any possibility I can repair my bootloader (if it's really broken)??, or Can I reflash my BA with other way around?? Without using the bootloader maybe??
UPDATE:
Later, I think I began to recognize the problem...
In every tutorial for Win7 that I read (this tutorial and d-two's tutorial), I was ask to update the driver of "Microsoft USB Sync". But in my case, that "Microsoft USB Sync" wasn't shown. I think it's because I haven't sync my BA with the PC yet (I've just reinstall my Windows, so all of the setting is gone). If you sync your BA, you will get the "Microsoft USB Sync" on your device manager.
But now, the problem is, I can't sync my BA with the PC, because of error in my PIM (Contact, Calendar, Task, Phone, Messages, etc). I only able to explore my devices through ActiveSync/Windows Mobile Device Center, not synchronize it. Even my ActiveSync/WMDC shows an error on the connection. So, I can't update/install the driver for "Microsoft USB Sync", because my BA have an error connection with the PC. Any ideas to solve it??
And would cloning method worked for my devices?? I mean, I get a cloning from another BA, install it in my BA, and then repeat the reflash process with my preferred ROM??
Please, need help over here....
try a hard reset
Broken Power Switch ...
Dear experts,
My device is PDA2K, last week i did upgrad from original windows to WM6.5 Pro_QVGA, Radio 1.12.00 ...... but the power switch is broken
..... as your experience how did that happened!!!! it was on cradle connected to WinXP, but since that day i'm trying to do flashing to install another Windows ...... i failed ...
Please Please Please .... Help me to do flashing or formating from pc or sd card ... because i'll never get into bootloader in my life.
Thank you ...