Related
hello,
I have an htc touch diamond and I can't use it as modem,
Mention that I have on my pc windows mobile center...
every think is work ok, the only problem is, I can't see it like a modem,
I have found some topics here, on this forum and I have trry some drivers but isn't work,
any ideeas?
thanks very much!
What have you tried? Normally, when your synced, you can start using internet on your pc/laptop by opening the "Internet Sharing" application on your Touch Diamond. After this there'll be some drivers installed on your PC, enabling Bluetooth PAN. These were the only things I need to do on my Vista workstation, after this I was able to browse the internet on my laptop using the Touch Diamond.
It's pretty fast as well, using HSDPA. I can reach download speeds up to 150KB/s! Good luck!
it is in Italian language and I don't understand it very well,
Now I have connect it yo my laptop
I will try to install English language to my phone, because I don't understand very well Italian language...
thanks a lot!!!
Milenco said:
What have you tried? Normally, when your synced, you can start using internet on your pc/laptop by opening the "Internet Sharing" application on your Touch Diamond. After this there'll be some drivers installed on your PC, enabling Bluetooth PAN. These were the only things I need to do on my Vista workstation, after this I was able to browse the internet on my laptop using the Touch Diamond.
It's pretty fast as well, using HSDPA. I can reach download speeds up to 150KB/s! Good luck!
Click to expand...
Click to collapse
Hi, like zmeutz I'm trying to setup my diamond as a modem.
Works great with IS and bluetooth PAN. But what I'm looking for is the diamond as a simple Modem.... It should be possible as when using any kind of "terminal" application over a bluetooth serial link connected to the diamond it does response to AT hayes commands....
However, when I try to use a ipaq to connect to the diamond through DUN it does not work....
I'm trying to do this for two purpose:
1/ Connect my ipaq running TTN6 so it gets traffic information from tomtom server. PAN works, but it's a pain compared to DUN. You need to activate BT on your diamond, run internet share, clik on two fields to set it up. Then click on connect to make it active. Then you need to go back to you IPAQ, before running you application, launch BT, got to settings, click on the diamond short cut for PAN. Then you can can launch your navigator on your IPAQ.... If you loose your connection, you need to start all the process again.....
While with dune, you would just need to activate bt on your phone.... The rest would be transparent as soon as you IPAQ application tries to connect to internet you get the connection...... At least it's the way it worked with my motoroal (razr).....
2/ sending faxes..... For this I need a true modem ;-).
Any ideas other that PAN?
Rgds,
JP.
HTC Touch Diamond Internet Sharing Problems
I have a HTC touch Diamond and I did as stated above but my phone asks for server information. But I have unlimited data, why doesnt it just continue on with the Evdo it has?
lol
all you need to do is install Microsoft active sync, then use the usb lead to plug in your diamond.
A menu will pop up, press internet sharing, your computer will recognize the phone as a network connection and drivers will be installed, hay presto your online
You can also use your bluetooth in the diamond and laptop.
Pair your device with the laptop, goto internet sharing, select bluetooth and connect.
Then goto (xp) Start - connect to - bluetooth pan
it will then connect to the device.
This way is slow but it works.
I have also written a guide on how to use you phone as a proper access point, search for it.
and if it doesnt appear
I've tried several times to set up my phone as a modem.
I have installed active sync on my laptop, but if i connect my Touch diamond "NO" menu pops up. Where can i find this menu? On my laptop or phone? And can anyone direct me to it. THNX
HTC Touch Diamond does not support Bluetooth DUN profile.
Its not worth the trouble. I would buy a dedicated usb modem. Only 20-30 Dollars
Hi there,
I got a car-pc since a while and have been using my sony ericsson with it... calls get transferred via bluetooth to the computer, as like phonebook in integrated into the car-pc software... all transmitted via bluetooth...
Now with the diamond, how do i set it up as a phone? winXP doesnt recognize other services than the moden funxtion
you should enable Remote SIM access on you Diamond: Start -settings - connections bluetooth SIM acces and also activate the service for your BT connection (do this in the first tab of the BT settings dialogue after connectig)
already done :-( But the Computer doesn't list other functions than modem for the HTC
Do i need any drivers for XP? Usually not...
Using Diamond & CarPC Via Internet sharing over BT
I have a CarPC in my car, it has a 7" touch screen & it is running WinXP and have built in Bluetooth. So for surfing in the internet , MSN, Skype in my car over the carpc i am using my HTC Diamond with the Internet Sharing icon and connecting it via Bluetooth to the carPC so i get FAST Internet over Bluetooth between my carpc and my HTC Diamond.
It works very good - very stable.
Matter of fact it is "capturing" my 3G Internet and pass it over Bluetooth to the carpc.
Solution works very well.
k, but i am not interested in using it as internet connection, i want to phone via the computers hardware, so the car-pc should act as an headset... besides that, he shoult be able to access the adress book and to begin calls... that for, i neeed 2 comports emulated, but how to create them?
could it be because the device is seen as a PDA, and not as a mobile phone?
I know somewhere here on XDA there is a reg hack for earlier devices to make them appear as a mobile phone to car kits. maybe the same thing will help here. I don't know where it is, can only suggest searching, unless anyone else can point you in the right direction....
I used to have PhoneConnector on my CarPC, with PhocoAdapter on the phone. It worked, but now this software is not supported anymore and unfortunately it does not work with WM6.
Freefone is not compatible either.
My good Blackbaron, I believe we users of CarPCs and Windows Mobile are scr...d!
By the way, sharing the 3G connection workds a treat, by USB, BT, Wifi... I just wish Vodafone would allow other ports than port 80
I still didnt realize what 3G is... ^^ I never owned a ppc before...
Well, on the CarPC the internet speed is as great as a DSL line, here is France I measured it at more than 3.5 MB/s (KS20 is limited to 4 MB/s with HSDPA, who knows why). Coming from the crappy Edge Motorola phone I had before, the browsing is truly amazingly fast!
help
golympio can you tell me step by step how to connect htc diamond via bluetooth for internet?
Try this app called JetWare
gerardo66 said:
golympio can you tell me step by step how to connect htc diamond via bluetooth for internet?
Click to expand...
Click to collapse
1) Launch the Internet Sharing application on your phone (all WM6 phones have it)
2) Select your 3G connection, and BT or USB, tap "Connect"
3) USB: have ActiveSync installed on the PC, connect the USB cable, it's done.
4) BT: you have to set up a BT PAN hosted from your phone, add your PC to it, it's done.
5) If your provider uses a proxy, setup Firefox to use it (Tools/Options/Advanced/Network)
6) If your provider has a filter on User Agent, then you need the plug-in "User Agent Switcher", to put the same User Agent string as on your phone.
There you go!
zmob123 said:
Try this app called JetWare
Click to expand...
Click to collapse
Looks interesting, I'll give it a try when I have some time. Do they have a trial version?
Yes they have, i leeched it... But i don't find the difference between now and before installing it...
Hi,
I'm trying to use the Bluetooth PAN setting in the Internet Sharing program with a Macbook (Mac OS X 10.5.4). I successfully paired the laptop and Kaiser. I start Internet Sharing on the Kaiser, go to the Bluetooth icon in OSX, click Tilt and click Connect to Network. This doesn't seem to work. Does anyone have suggestions?
I can successfully get it working with Windows XP so I'm guessing it's OSX's fault?
SPL: 3.56 hard
Rom: NotATreoFan's V1 Final (http://forum.xda-developers.com/showthread.php?t=421852)
Radio: 1.65.24.36
Might anyone have an idea, or maybe the better question is has anyone ever gotten Bluetooth PAN working with OSX?
anonova said:
Might anyone have an idea, or maybe the better question is has anyone ever gotten Bluetooth PAN working with OSX?
Click to expand...
Click to collapse
It works for me on a mbpro with 10.5.5. It's been a while since I've set it up, but I don't remember doing anything special to get it working.
Make sure you set your shared internet connection to the correct setting ( Media Net or My ISP )
I have found that tethering using MY ISP works the best and seems to have a tad less latency.
I am running a MB Pro C2D with 10.5.3
My "Hack Pro " is running 10.5.2 and is also tethering with no issues.
P.S.
One more thing. Make sure the phone is set to Visible. Although you can pair it , if its not in Visible mode, it will NOT work
Do you get a connection and it just wont give you an active connection or does your laptop attempt to tether and give a network connection error ?
Here's how I'm trying everything. The device and computer are already paired. The device is visible.
Open Internet Sharing.
Set PC Connection to Bluetooth PAN and Network Connection to MEdia Net.
I tap connect, and the status changes to "Device setup finished. On the PC, connect Bluetooth PAN."
On the Macbook, I click the Bluetooth icon on the menu bar, hover over the device's name, and click Connect to Network.
On the device, the status changes to "Connected."
When doing this in Windows, that's it. I can open up a browser, and the internet is working fine. But on my Macbook, I open up a browser, and I'm not connected to anything. I open up the Network preference pane, and nothing is connected. OSX doesn't see the Bluetooth PAN profile is maybe the problem?
anonova said:
Here's how I'm trying everything. The device and computer are already paired. The device is visible.
Open Internet Sharing.
Set PC Connection to Bluetooth PAN and Network Connection to MEdia Net.
I tap connect, and the status changes to "Device setup finished. On the PC, connect Bluetooth PAN."
On the Macbook, I click the Bluetooth icon on the menu bar, hover over the device's name, and click Connect to Network.
On the device, the status changes to "Connected."
When doing this in Windows, that's it. I can open up a browser, and the internet is working fine. But on my Macbook, I open up a browser, and I'm not connected to anything. I open up the Network preference pane, and nothing is connected. OSX doesn't see the Bluetooth PAN profile is maybe the problem?
Click to expand...
Click to collapse
Ahhhhh When you pair the phone to the mac, make sure you have internet sharing enabled on the phone before you go into pair mode. Otherwise mac osx doesnt see the PAN capability. I think thats what I had to do.
I tried with Internet Sharing pre-connected, but it still didn't work. I did get it working though! In the network connections, Bluetooth does not equal Bluetooth PAN. I went to the little plus at the bottom, and specifically added a Bluetooth PAN interface, and it picked the device up.
Thanks for all of the help!
anonova said:
I tried with Internet Sharing pre-connected, but it still didn't work. I did get it working though! In the network connections, Bluetooth does not equal Bluetooth PAN. I went to the little plus at the bottom, and specifically added a Bluetooth PAN interface, and it picked the device up.
Click to expand...
Click to collapse
Unfortunately, I am on HTC Touch with a WM6.5 ROM, and even though I added the Bluetooth PAN interface manually, my Mac is still not picking up the phone, even though it's been paired successfully and Internet Sharing pre-connected.
OK this is for last year but just in case someone else searches for this a solution I found a while back
Added step open "com port 1" on the WM, not sure where I found that, otherwise the mac keeps "dialing" and the phone says "???? no need to dial, 3G not modem"
These steps work for me on SE Xeperia1 with WM 6.5 and Mac 10.5.8.
http://www.hightechdad.com/2007/05/...sharing-from-windows-mobile-6-to-mac-os-1049/
"Now with Windows Mobile 6, Bluetooth PAN (Personal Area Network) is used. So, if you are on Mac OS 10.4.9, you now have the ability to use a Network Port called “Bluetooth PAN.” Here are the high-level steps you use to enable your Bluetooth Internet Sharing:
1. Turn on Bluetooth and BT discovery on both your WM6 device and your Mac
2. Set up a Pairing between the two devices
My steps + Setup Bluetooth from Phone to Mac. Do it form the phone to the mac not the other way around.
+ Opem Comm port one from Phone bluetooth setup.
3. Enable the Bluetooth PAN port under your Mac’s Network Preferences (Network Port Configurations) by clicking the checkbox
4. Ensure that your devices are “talking together”
5. Start “Internet Sharing” on your WM6 device and click “Connect”
6. On your Mac, it is helpful having the “Show Bluetooth status in the menu bar” enabled
7. On your Mac, from the Bluetooth menu, select “Join Network on [WM6 device]“
8. That is it! (You should have internet connectivity on your Mac, provided you have good signal on your WM6 device). You can even verify that you got an IP address from your WM6 device by going to Network control panel and selecting Bluetooth PAN. Mine shows a 192.168.0.XXX number.
I hope that works. This is a good tip to know if you travel a lot and don’t want to pay for the expensive hotel internet services. Just plug power into your phone and your laptop, connect and you have “dialup” speeds for no additional costs!
If you have questions, write a comment below. If this works for you, DIGG it!
Don’t forget, you will drain your battery pretty quickly and use a lot of bandwidth from your cellular provider (especially if your internet service has a cap)."
Hi Guys
Just got the Diamond2 from devicewire, and I'm really pleased with it.
One thing that differs from my Touch Diamond is that when I try to use internet sharing my laptop* won't recognise it as a BT PAN device.
I realise this may be a bit premature, but has anyone else experienced this yet? Any fixes out there, or even fixes for the Touch HD which may be appropriate?
Thanks
Stoatie
*Lenovo X61s
WM WiFiRouter
I have this WM WiFiRouter and Access point (Wifi and BT) on all the time
Sorry just found !!! You now have buy before try version 1.30 had a trial !!!
http://www.wmwifirouter.com/
Bluetooth PAN
Stoatie
I initially had the same problem until I realised I had to go into Internet Sharing on the Diamond2 and click connect once I had selected Bluetpooth PAN as the PC Connection. Once this was done I was able to join the PAN from my Vista laptop.
Hope this solves your problem.
b10lld said:
Stoatie
I initially had the same problem until I realised I had to go into Internet Sharing on the Diamond2 and click connect once I had selected Bluetpooth PAN as the PC Connection. Once this was done I was able to join the PAN from my Vista laptop.
Hope this solves your problem.
Click to expand...
Click to collapse
I don't understand what you mean. Do you mean that you think I wasn't pressing "connect" to connect the two devices up?
Initially I paired the 2 devices and connected them via bluetooth. I then tried to join a bluetooth PAN from my laptop and it showed my diamond2 as a bluetooth access point. I pressed connect on my laptop and got an error message.
It wasn't until I realised that I needed to initiate an Internet Sharing connection from the phone first and then join the PAN from the laptop as well (connecting on both devices) that it worked. And it works fine.
Sorry if your problem is different.
Hi All,
Long story short,
I broke my 3G modem somehow; Huawei E169, it can't find the network but will install fine and try to find it.
I want to pull the SIM out of it and use my X1 as a modem. Last night I tried but couldn't make it connect to the network. X1 is custom unlocked, SIM is Optus in Australia. I have the SP code etc but do not know where to put this in the phone?
Any help would be great thanks!
it works fine on mine.
1. your PCs bluetooth must have the Bluetooth PAN stack.
2. pair PC with X1
3. on the X1, go to Start, then Internet Sharing, then turn on Internet Sharing
4. in Windows, go to your Bluetooth devices folder, right click on X1 and connect via Access Point
5. done
if connecting via USB cable, just do Step 3. and connect USB cable to PC.
apparently the X1 supports Dial-Up Networking (DUN) as an alternative but the setup is much more complicated.
All sorted now thankyou.
I needed to set the correct access point in my phone internet settings.
Will be trying the usb cable and BT very soon. Thanks!