Related
Hi all,
I had an O2 XDA Stellar which I believe is the HTC TYTN II. However, this phone was stolen a couple of weeks back. I purchased a second hand one today which is sim locked to the orange network. I managed to break the lock by following the instructions on this link http://forum.xda-developers.com/showthread.php?t=433835. I followed the instructions word for word till step 5.
The problem is now though it accepts the SIM and I can dial out, I don't have any audio on the calls So I can call and my phone also rings when I receive a call but I can't hear the caller nor can I be heard at the other end
Also, I hate the orange rom (and I used to complain about the O2 rom) and I wish to use the default HTC WM 6.1 professional upgrade the problem again is that it asks for a serial number and my serial number starts with DCOxxxxxxxxxxx and it says that this is not a valid serial number
What do I do now? Has my phone become a brick Please do help I can't bear the thought of having one stolen and the other toasted by me
All help will be greatly appreciated
fmervin said:
Hi all,
I had an O2 XDA Stellar which I believe is the HTC TYTN II. However, this phone was stolen a couple of weeks back. I purchased a second hand one today which is sim locked to the orange network. I managed to break the lock by following the instructions on this link http://forum.xda-developers.com/showthread.php?t=433835. I followed the instructions word for word till step 5.
The problem is now though it accepts the SIM and I can dial out, I don't have any audio on the calls So I can call and my phone also rings when I receive a call but I can't hear the caller nor can I be heard at the other end
Also, I hate the orange rom (and I used to complain about the O2 rom) and I wish to use the default HTC WM 6.1 professional upgrade the problem again is that it asks for a serial number and my serial number starts with DCOxxxxxxxxxxx and it says that this is not a valid serial number
What do I do now? Has my phone become a brick Please do help I can't bear the thought of having one stolen and the other toasted by me
All help will be greatly appreciated
Click to expand...
Click to collapse
Did you actually read anything or did you just start hacking away ? I will cut and paste a few items out of that thread, so that you don't have to actually read it .
PLEASE READ THE *FAQ* BEFORE FLASHING OR ASKING QUESTIONS!!!
* IF YOU DONT NEED TO FLASH A NEW ROM THEN PROCEED TO STEP 6 TO PUT YOUR DESIRED RADIO BACK*
7. After I flash a Rom I dont have any sound in calls and the camera is black
The Radio has to match the version of Rom you flash i.e. WM6.1, an incorrect Radio will give sound and camera problems. Read The Ultimate Radio Thread to find a Radio that matches the Rom there are lots to try on there if one doesnt work then try another.
3. What are the different types of Unlock?[/B] (answer by DaveShaw)
The three stages of unlock are:
SIM: Allows you to use SIM's from another carrier. Can be done using codes or unlocker programs on xda-devs.
Security: Allows you to flash radios from another device - It does other stuff, but this is all the casual user will use it for
CID: CID unlocking is an old concept, nowadays you flash HardSPL instead. This lets you flash any ROM, Splash or Radio (depending on sec unlock) to your device. N.B. the CID is the carrier ID (e.g. HTC__001). The stock SPL's only let you flash ROM's that match the CID in the ROM image with the CID on your device.
Obviously you did not unlock your phone if a serial number is needed to flash a new rom. I would re read everything and do it again
Thanks for the reply
denco7 said:
Did you actually read anything or did you just start hacking away ?
Click to expand...
Click to collapse
As a matter of fact I did read that more than once.
denco7 said:
* IF YOU DONT NEED TO FLASH A NEW ROM THEN PROCEED TO STEP 6 TO PUT YOUR DESIRED RADIO BACK*
Click to expand...
Click to collapse
As you can see I'm a bit of a newbie here, so wasn't too sure if I did need to flash to a new rom. But I did anyway. And the call problems still remain
denco7 said:
7. After I flash a Rom I dont have any sound in calls and the camera is black
The Radio has to match the version of Rom you flash i.e. WM6.1, an incorrect Radio will give sound and camera problems. Read The Ultimate Radio Thread to find a Radio that matches the Rom there are lots to try on there if one doesnt work then try another.
Click to expand...
Click to collapse
I've been through this link as well and I was contemplating installing the latest version of the HTC WM6.1 ROMS (version 3.34.721.2, radio version 1.70.19.09) available at http://wiki.xda-developers.com/index.php?pagename=Kaiser_ROMs However I was not sure if this would be ok and (at the risk of sounding extremely dumb) I was not sure what WWE stood for
denco7 said:
3. What are the different types of Unlock?[/B] (answer by DaveShaw)
The three stages of unlock are:
SIM: Allows you to use SIM's from another carrier. Can be done using codes or unlocker programs on xda-devs.
Security: Allows you to flash radios from another device - It does other stuff, but this is all the casual user will use it for
CID: CID unlocking is an old concept, nowadays you flash HardSPL instead. This lets you flash any ROM, Splash or Radio (depending on sec unlock) to your device. N.B. the CID is the carrier ID (e.g. HTC__001). The stock SPL's only let you flash ROM's that match the CID in the ROM image with the CID on your device.
Obviously you did not unlock your phone if a serial number is needed to flash a new rom. I would re read everything and do it again
Click to expand...
Click to collapse
I maintained the default that was given by the unlocker for the CID (I think all zeros). Do I have to change this as per the ROM image? I don't mind re-doing this again it's a relief that my device isn't busted
No your phone isn't busted. Go into bootloader and check what it says next to spl, if you followed Mark's steps, it should say 3.29 Hard. If that is what it says ,then you can flash any Kaiser rom you want. If it doesn't then start over again.
WWE stands for World Wide English and those roms are all in English. That rom you picked will be fine, if you do not wish to explore the fine world of custom roms ? Maybe later.
You only have to CID unlock once by following the steps, not at every rom flash.
No sound means wrong radio, 6.0 roms need 6.0 radios and 6.1 roms need 6.1 radios. If the rom has a radio in it already then flash away.
Thanks Denco Flashed the ones I mentioned and it works perfect. Can't believe I actually have a working device Thanks for all your help, really great.
Now to sync my data to my new (second hand) htc and I'm good to go
Another question, the device works fine, however since it is a HK rom, it seems to have localised to HK. I've changed this as much as possible to UK. However, I'm wondering if this will affect anything else? For example the gps? Is there any quicker way to configure this globally so all settings use UK instead of HK?
Why didn't you flash the latest UK ROM.
Use this code: HT750GB02264 to download from HTC's site.
fmervin said:
Another question, the device works fine, however since it is a HK rom, it seems to have localised to HK. I've changed this as much as possible to UK. However, I'm wondering if this will affect anything else? For example the gps? Is there any quicker way to configure this globally so all settings use UK instead of HK?
Click to expand...
Click to collapse
Once you are unlocked and HardSpl'd you can flash any rom you want. Pick a UK one another WWE rom or a custom rom. Test a bunch until you have one you like. Your only restriction is it has to be a Kaiser rom. And with all the Kaiser roms available, it is not a restriction at all.
Mister B said:
Why didn't you flash the latest UK ROM.
Use this code: HT750GB02264 to download from HTC's site.
Click to expand...
Click to collapse
Wow, thanks for that, I was looking for a valid serial through which I can download from the htc uk site One question I had is do I install the radio which I download from htc? Or do I keep the one I have already flashed? The one I have flashed yesterday seems to be a later version than what I've downloaded from htc
denco7 said:
Once you are unlocked and HardSpl'd you can flash any rom you want. Pick a UK one another WWE rom or a custom rom. Test a bunch until you have one you like. Your only restriction is it has to be a Kaiser rom. And with all the Kaiser roms available, it is not a restriction at all.
Click to expand...
Click to collapse
1. I keep hearing on this forum about Hard SPL, I'm not sure what this is used for or why it is required but I followed the instructions and it seems I had installed JumpSPL1.56-KAIS.exe. Now, since then I had flashed the rom, so do I need to reinstall this again? Is there some other one I should be using? I come across different versions on some threads. Also, how can I check the version of HardSPL I have?
2. When I view the memory (under settings) it shows me Storage and Program. However, I can't seem to see any storage area in file explorer. I know in my old xda 2i, there used to be a separate storage area. The reason is because some of the apps I install are quite bulky for example lexisgoo english dictionary (the dictionary files themselves are about 18mb) and this fills up the main memory. How can I install this in the storage memory? (not storage card since I sometimes swap storage cards)
Sorry lot of questions I know, but I'm a newbie and all help will be greatly appreciated
The UK downloaded ROM will install the radio too.
I would do a bit of testing with your current set-up, then flash the UK ROM.
Test the new UK ROM & radio & then reflash the radio only if you want (do some searching on Radio versions)
Newer versions are not always best, chasing the latest builds normally bites you in the ass at the end of the day.
Check HardSPL by going into bootloader:
* Using a stylus, press and hold the soft reset button at the bottom of the phone along with the camera button
* Release both buttons once the bootloader screen appears
* Exit bootloader by pressing soft reset button
Once you have installed HardSPL thats it, job done (you installed it during unlocking)
What you see in file explorer regarding storage is correct: 128MB RAM for running software ect & 256MB ROM for storing your programs ect (WM2003SE was different)
ROM can be increased by using one of the cooked lite ROMs if storage space is a concern.
Mister B said:
The UK downloaded ROM will install the radio too.
I would do a bit of testing with your current set-up, then flash the UK ROM.
Test the new UK ROM & radio & then reflash the radio only if you want (do some searching on Radio versions)
Newer versions are not always best, chasing the latest builds normally bites you in the ass at the end of the day.
Click to expand...
Click to collapse
Will do, the HK version seems very stable, the only thing that bothers me is the region settings. Anyway, I think I'll give the UK Rom a go and if that works well I'll stick with it
Mister B said:
Check HardSPL by going into bootloader:
* Using a stylus, press and hold the soft reset button at the bottom of the phone along with the camera button
* Release both buttons once the bootloader screen appears
* Exit bootloader by pressing soft reset button
Once you have installed HardSPL thats it, job done (you installed it during unlocking)
Click to expand...
Click to collapse
I checked the version and this is what it showed:
KAIS130
SPL-3.2.9.Hard
CPLD-8
Click to expand...
Click to collapse
TBH, I don't know what any of that means But do you think the version I have is ok, or do I need to upgrade this to some other version?
Mister B said:
What you see in file explorer regarding storage is correct: 128MB RAM for running software ect & 256MB ROM for storing your programs ect (WM2003SE was different)
ROM can be increased by using one of the cooked lite ROMs if storage space is a concern.
Click to expand...
Click to collapse
I've attached a screenshot of my memory screen. The bit that puzzles me is that the storage area apparently has a lot more storage but I do not have an option to install all my applications on that area or atleast the bulky ones. I don't think I need a lite one since I do have 112MB free in the storage area which is more than sufficient for all the apps I usually install. Can you advise how I can install apps to the storage area as well?
Lastly, I was wondering if it is possible for me install my apps on the rom and then kind of take an image of my setup and flash the rom with this setup. That way when I do a hard reset, all my apps are installed again. Which will save me the trouble I know sprite backup does something like this but I'd prefer if it was in the rom
Thanks for all your help, it has given me a lot of confidence in these matters. Something I probably wouldn't have attempted
Mister B said:
Test the new UK ROM & radio & then reflash the radio only if you want (do some searching on Radio versions)
Newer versions are not always best, chasing the latest builds normally bites you in the ass at the end of the day.
Click to expand...
Click to collapse
I agree 101% and it appears fewer resources are put into ironing out bugs in the WM 6.1 ROMs than the WM 6.0 ones. I replied to fmervin's post in the ROM forums along these lines.
If all is running OK I would stick with your current HardSPL.
When installing your applications choose the option of installing to "Device"
You could install all your apps into a ROM, this would be cooking a ROM & is a complex process.
I would suggest a backup via Sprite or SPB. I use SPB v2.0 build3065 & it works well for me, preference of backup software is a bit of a Marmite scenario, you either love it or hate it.
Lastly, I was wondering if it is possible for me install my apps on the rom and then kind of take an image of my setup and flash the rom with this setup. That way when I do a hard reset, all my apps are installed again. Which will save me the trouble I know sprite backup does something like this but I'd prefer if it was in the rom
Click to expand...
Click to collapse
You can't do that, it is flash memory. It's not like you can partition the hard drive.
But this is the easiest way to get your Apps and settings back after a flash.
Try this Sashimi Auto installer by a former XDA member. It is a nice little program that installs all your apps after a flash
http://www.winmo-experts.com/viewtopic.php?f=7&t=4
Help Please
Hey Denco..Than'x for considering my thread & giving out suggestion towards the link to check the info. But i m really nt that techy afterall so i can burn a ROM on my Tytn II. Even though i tried to burn a RUU rom that supports TyTN II ..Its just gets disconnected from USB mode..So i was looking forward to start it initially with some comparatively easier to install .cab files..Can't these RUU files be transformed into .cab files or maybe some other version of Manila 3D cab file that is completely fixed...I seriously have done a lot of research upon this but nothing looks like working. So please if you have some links to .cab files that can give a better & different look to my Kaiser running Windows 6.1...It'l be a great help !!
Than'x & regards in advance
vicky_crispy said:
Hey Denco..Than'x for considering my thread & giving out suggestion towards the link to check the info. But i m really nt that techy afterall so i can burn a ROM on my Tytn II. Even though i tried to burn a RUU rom that supports TyTN II ..Its just gets disconnected from USB mode..So i was looking forward to start it initially with some comparatively easier to install .cab files..Can't these RUU files be transformed into .cab files or maybe some other version of Manila 3D cab file that is completely fixed...I seriously have done a lot of research upon this but nothing looks like working. So please if you have some links to .cab files that can give a better & different look to my Kaiser running Windows 6.1...It'l be a great help !!
Than'x & regards in advance
Click to expand...
Click to collapse
I think you need to decide what it is that you want to accomplish. Unless you cook your own rom, there is no way to add apps to the rom ( so that they will remain after a hard reset) Your rom is wyour phone's base operating system, it contains your OS (WM 6.1 ) and can only be replaced after completely erasing and replacing all files from the previous rom.
If it is a new rom you want, pick a rom that interests you and follow these instructions verbatim .
http://forum.xda-developers.com/showthread.php?t=433835
Your phone will go to the bootloader screen ( three color) and it will disconnect from usb during the process, but be patient until the end. When it says it takes ten minutes, it takes ten minutes. Leave the room if you have to , to keep from getting impatient.
If you just want to keep your OEM WM 6.1 and keep it simple, but change the look of your phone try this,
http://www.htcwiki.com/page/Manila+2D+and+M2D+Themes
This will change the look and feel of your phone with uninstallable .cab files and will not affect the rom or brick your phone by accident.
Hello!
I have a Tmobile MDA Vario 3 and the following problem:
I used my phone normally every day, and one day no ringtones are working... I can hear them choose one of the sounds, but no sound if somebody rings me...
what can it be? I dont wanna make a hardreset, because many programs on it and i dont wanna lose them...
I did a hardreset and used before sprite backup, i tested the ringtone and IT WORKS, now i put back my backup and no ringtones working now again, how can i find the mistake in the system? Can i look into the registry like normal windows too?
in another forum i saw someone means it can be the divx player, i deinstalled it, but nothings better...
I NEED HELP... what can i do?
Regards
Can't you just put the programs back on there? It's really not that hard.
ChumleyEX said:
Can't you just put the programs back on there? It's really not that hard.
Click to expand...
Click to collapse
Its too much for me...
Its an tmobile device and i putted manually the o2 internet settings in there nobody knows whats the defect on there?
Regards
I could flash and setup my Tilt in no time flat.
Ok, i will do a hardreset, but is there a ROM for the Vario 3 so that i have an original HTC ROM?
And can i flash the phone then to WM 6.5?
Do you have any links for me?
are you on a flashed non OEM rom?
I am on an original tmobile rom, and i i have to reset i wanna change to another rom like windows mobile 6.5, i have to change rom to a htc rom 6.1 and then i have to go to 6.5 right? i wanna put away tmobile settings on hardreset!
Well if you hard reset it will put the oem rom on it. Then you follow the instructions to be able to flash roms on it. Until you flash a rom on it, every time you hard reset it the factory rom will install.
Can you give me a link where i find a description what to do for this?
I wanna flash the rom to HTC WM 6.1 original, and after this i wanna install 6.5 is this the right way??
[Resources] Flashing Your First Kaiser Rom (For Noobs)
No need for interim flashes after hard-spl you can flash a 6.5 make sure you read about Radio update
Maybe you have installed some softwares. let check recent installed softs and uninstall them, then restart. No need to use other rom if you like it
If it still does not work, do hard-reset.
Goodluck
I am trying to get the cool 4 shortcut buttons and was directed to something called Cookies Home Tab. I installed it but no program showed up.
I would then try and uninstall it an install it again with sense deactivated, but when choosing uninstall on the program (which shows up on the "remove program" menu, but not in the start menu) the "busy-cursor" is just rotating and nothing happens. I tried powering off and try again, and the same thing happens: It says its uninstalling, but it takes forever and nothing happends.
Can someone help? How do I get the program properly installed. I am running a danish original rom and assumed it would be compatible when directed there. I am not sure where to find my sense version. Can it be that its 2.16xxxxx or is that windows?
came99 said:
I am trying to get the cool 4 shortcut buttons and was directed to something called Cookies Home Tab. I installed it but no program showed up.
I would then try and uninstall it an install it again with sense deactivated, but when choosing uninstall on the program (which shows up on the "remove program" menu, but not in the start menu) the "busy-cursor" is just rotating and nothing happens. I tried powering off and try again, and the same thing happens: It says its uninstalling, but it takes forever and nothing happends.
Can someone help? How do I get the program properly installed. I am running a danish original rom and assumed it would be compatible when directed there. I am not sure where to find my sense version. Can it be that its 2.16xxxxx or is that windows?
Click to expand...
Click to collapse
If you cannot find your manila version, or at least search on how to find it, you really need to learn more before you mess up your phone.
I assume you did a hard reset after your registry issue. If not I suggest you do as you will probably have to do it a few times as you attempt to customize your device.
Your manila version can be found in Settings\Device Info\Software Info.
Read the thread on Cookies Home tab for compatable versions and install instructions. Post your questions there.
p.s. Thanks for implying...
I am really sorry for sounding like a total noob, but I DID read the post, installation instructions and whats not. I also read the "how to find your manila version" which also said to go to settings tab - device info - software info. The thing is that its danish on my phone and I cant find anything called device info on my tab, only "about" which leads me to a webpage with a lot of copyright and legal mumble jumble.
When going to settings - advanced - about the device I get a tab called version, where it says Rom Version 2.16.403.1 (67041) dan. But I dont know if thats it.
But lord, how many original stock roms can there be? Its a pretty new phone and I installed every HTC update available to me. I must say that configuring this little diamond seems to take a rocket scientist or above. I can use a computer pretty well, but getting a little modifications to the HTC UI seems to take a phd
You seem like a nice guy, and I would like to learn. Maybe you can help me out so I dont have to ask so many noobish questions. I really tried to learn by myself but it is a new world to me and it is quite overwhelming.
1) I read that installing a rom is ireversible. Does that really mean that I under no circumstances can replace the original software? Is a cooked rom really a whole other OS and replace windows mobile 6.5 completely? Or is it just a modified windows?
2) What is the distinction between HTC Sense, Touch Flo and Manila, if any? As far as I read the black and white icons is manila and the colored ones is sense... Is that true? And does that mean that I cant use any programs that needs manila to run if I have the HTC Ui with the colored icons?
I hope the above questions helps me to a basic understanding, so I further on dont have to ask so many questions.
PS) after installing TD2 tools my screen rotation line in my system registry came back, and I got rid of the landscape.. Thats one problem solved. Call recording aswell. If I find a way to get these 4 shortcut-buttons available and set one of them to my to-do list I think Im done.. No more tampering.. I promise.
came99 said:
1) What exactly is the difference between installing Cookies Home tab and installing another rom? As I understand it, a rom is a whole other OS, where this software only is a skin? Correct?
Correct, The ROM is the whole OS, where CHT is a modification to the Sense (Manila) UI.
2) I read that installing a rom is ireversible. Does that really mean that I under no circumstances can replace the original software?
No, You must first install hard SPL to be able to flash a cooked(custom) ROM.
Once you install HSPL, your device is considered "out of warranty".
However you can reflash a Stock ROM and then reflash Stock SPL to return the phone to the factory state for warranty purposes. So it can be reverted.
3) What is the distinction between HTC Sense and Manila, if any?
They are one and the same, also referred to as Touch Flo 3D (TF3D)
4) The original question about getting Cookie to work, if someone feels like helping.
If you have installed Cookie's Home Tab and soft reset, when you are on your home screen you should see the flip clock (assuming that in Settings\System\Home\Items is set to HTC Sense), on top right of that is a little dash, this opens up additional panels for your shortcuts.
There should also be a new program possibly in settings or \Programs\Tools called CHTEditor to access your tab settings.
I suspect that it installed, you just didn't know how to access it.
Lemme know.
PS) after installing TD2 tools my screen rotation line in my system registry came back, and I got rid of the landscape.. Thats one problem solved. Call recording aswell. If I find a way to get these 4 shortcut-buttons available I think Im done.. No more tampering.. I promise.
Click to expand...
Click to collapse
See above for answers. One quick word of advice; If the program interfaces with your today screen, phone functions, etc. install to device memory and never to Storage Card. Programs that just tweak the registry and settings can be installed to SD card.
Uhm, and I wouldn't be promising anything because its addicting. Once you pop, you can't stop!
Sorry.. I edited my post while you were answering. I found the preguide to roms which was just about basic enough to enlighten me. Your answers helped a lot to, and everything fell into place.
I do think that I will stay away from flashing as it seems like risky business.. The option to hard-reset without to much hassle seems like the emergency brake I like available to me
At the moment I am trying to reinstall Cookies Home Tab, but the installation just hangs.. Probably because it wasnt uninstalled correctly. Any tips other than Hard Resetting which means several hours of setup
Edit: Ahh f... it.. I may aswell do it.. All the tampering made my phone slow anyway.. Now I know what I need and can get it to work without too much experimenting..
Thanks dude.
I did some research on your stock ROM and it looks like you are running Manila 2.1 which is the older version so many tweaks you are attempting may be for 2.5.
You would be better off changing ROMs.
Here is a download of our stock ROM for warranty purposes, keep it just in case. You may have to register for the site, but you may also find a nice cooked ROM in your language on that site. Dutty is a great chef and I use his ROMs because of their stability.
I can attempt to walk you through HSPL, but there have been many issues lately. Almost seems like the only way to get it to work is to "donate" to the developer.
Okay Mr Dope Pusher.. i see where you are going.. Telling me to stay away from these sheningans and 1 hour later you got me hooked anyway
Jokes aside.. Yes.. I Do think I am gonna need some help here.. While the stock backup rom is downloading I will try and find out for myself, but I would very much like some confirmation on what to do before I take the leap.. Stay tuned and thank you very much.. Your help is very appriciated.
I have a question though.. Now I downloaded the stock rom, but what if my phone breaks when Duttys Rom is installed.. Then I wont be able to reinstall the original rom before sending it in for repair. And then Im screwed warranty wise, right?
..., in anticipation of your next question;
As long as you have over 50% battery and do not interupt the flash (unplug the USB) there are very few chances of it bricking.
I have never had it happen and most errors are correctable with a hard reset. It really sounds worse than it is.
Most devices get bricked because the user attempts to flash a cooked ROM w/o HSPL or a ROM or radio from another device.
I have attached 3 files.
Do the following after you download these files;
1. Remove your SIM and SD card.
2. Sync your device to your PC through Active Sync or WMDC depending on your windows version.
2. Copy the enablenewrapi.cab to your device through file explorer and install
to device memory.
3. Open both the SPL 1.83 and the RUU zip files and place contents of both into a new folder.
4. Run the RUU.exe and you should see a progress screen appear.
5. With any luck, you won't get stuck at 0% and the flash will complete.
As the screen states, it may take up to 10 minutes. You will see your device disconnect from active sync, which is normal. Let it run until it completes and do not open anything or let your PC go into standby. Also, you may want to disable your AV and any firewalls as these can mess with the installation.
Make sure you have greater than 50% battery before you attempt this as any interuption during the flashing process can brick your device.
If the steps above complete, you can go into bootloader mode by holding down both volume keys right after you hit the soft reset buton, but before the device begins to boot. You may have to try a couple of times if you are not fast enough. Or you can power off the device then hold both volume keys and press the power button. In bootloader mode which is a tri colored screen, you should see SPL: 1.83.Olinex, then you will know it has installed correctly.
From this point, you are able to flash any cooked Topaz ROM.
The ROM flashing process is the same as HSPL in regards to placing the ROM's .nbh file into the same folder as the custom RUU.exe, so keep that RUU.exe file for future use.
You need only flash HSPL once to continue to flash as many ROMS as you like.
If you ever have to revert to stock, you would install the ROM you downloaded, then find the StockSPL file from the HSPL thread and follow the instructions.
Always hard reset after you flash a new ROM.
**If you are not successful in flashing HSPL, you will need to go to the HSPL thread and read up on opening a ticket with HTC Support, which will give you an autoinstaller that will work once you donate through the program. I believe they are asking for 4gbp.
Ok.. And one of the above files is the Dutty Rom? Edit: Oh I se.. It isnt.. I will download it then..
Will it look and feel similar to Sense, just with more features and customisation options?
You write: Most devices get bricked because the user attempts to flash a cooked ROM w/o HSPL or a ROM or radio from another device.
Can you please elaborate? I understand it like you need to make sure I install the hspl first before cooking, but "radio" from another device. Please explain it for a dummy as me, so I dont attempt to do it by accident.
came99 said:
Ok.. And one of the above files is the Dutty Rom? Is it available in danish as is, or do I have to do something.
Will it look and feel similar to Sense, just with more features and customization options?
Click to expand...
Click to collapse
No, I have not provided you with a ROM, just the HSPL unlocker.
You can go to HTCPedia and search for a Danish ROM with manila 2.5, or take a look through the ROM development thread and find one from another chef. It should have Sense installed but 2.5 unless it states otherwise. 2.5 has more features and functions and is the most current.
Many ROMs are multilanguage so I believe you select your region language when the ROM first loads. Just look for one that supports DAN. I use WWE (World Wide English) so I am not experienced with multilanguage variations.
Just make sure your HSPL is successful before you attempt to flash a ROM.
If you search hard enough you may even find a ROM with CHT cooked in which will alleviate you from having to install it yourself, but I suspect that your previous install didn't work because your on Sense 2.1
I have never used CHT, but use Max Manila Themes which is just a different mod, but I am thinking about trying CHT.
I'll take a look and see what I can find.
Regarding Radios;
A stock ROM comes with the OS and Radio ROM.
Most cooked ROMs take just the OS and tweak it for best performance, adding programs, removing other useless programs and do not include the radio ROM, therefore you will still have your stock Radio unless you flash a cooked ROM that has included the radio (usually denoted in the title of the ROM by the radio#, i.e. 4.49.25.57 (which is a Topaz radio version)
The only time you can brick is you attempt to install a radio from another device (sometimes they work better) such as a Blackstone radio to a Topaz device unless your SIM is unlocked or attempting to flash a Topaz radio w/o HSPL.
Personally, there are enough Topaz radios posted in the radio thread that I don't need my SIM unlocked to try others.
Symptoms of a problem radio are poor signal strength, rapid battery loss and your device heating up.
I have switched my radio ROM a few times but honestly haven't noticed a difference from my stock radio.
The stock ROM you downloaded would replace your Stock Radio if you happen to flash to a different one.
Your region and carrier are also a factor in choosing a radio, so again, just stick to stock unless you have issues.
Dude.. That radio thingie made me EXTREMELY paranoid and I see that there is dozens of different roms from dutty and thousands of rom in general where many of them seems to come with radio-thingies... I am extremely afraid of choosing something that will brick my system, so please, please help me through this, even though you already have been extremely helpful.
If I were on my own, I would go with this:
http://htcpedia.com/duttys_topaz_wm_leo_r_rtm_e11d19c3e22de899a/soft/htc-topaz-rom.html
But to be honest I dont know if it will work on my device or if I will be able to get it with a danish language pack..
Please help me choose the right one.... I am ready to rock, so I hope for a quick reply, and I promise I will do a extra good deed tomorrow to repay the world for all the help you gave me tonight.
came99 said:
Dude.. That radio thingie made me ETREMELY paranoid and I see that there is dozens of different roms from dutty and thousands of rom aswell where many of them seems to come with radio-thingies... I am extremely afraid of choosing something that will brick my system, so please, please help me through this, even though you already have been extremely helpful.
If I were on my own, I would go with this:
http://htcpedia.com/duttys_topaz_wm_leo_r_rtm_e11d19c3e22de899a/soft/htc-topaz-rom.html
But to be honest I dont know if it will work on my device or if I will be able to get it with a danish language pack..
Please help me choose the right one.... I am ready to rock, so I hope for a quick reply.
Click to expand...
Click to collapse
Don't sweat it Bro, if its posted as a Topaz ROM then its got the Topaz Radio, the only thing you risk is not being able to connect to certain 3G bands.
I've used Dutty's R-8 and its not a bad ROM, but its a little outdated and I didn't see that it had multi language support.
I am really having a hard time locating a Danish language ROM.
I find FRE. GER, ITA, ESN, NLD, WWE, but no DAN????
"I am really having a hard time locating a Danish language ROM.
I find FRE. GER, ITA, ESN, NLD, WWE, but no DAN????"
Then it aint just me being total clueless.. I cant find any either..
Im bafled by this world.. I basically have two modest demands: To record calls in mp3 and get easy access to my to-do list.. preferably on my homescreen, but just as good by one of the nifty Hotbuttons Ive seen in pictures..
To get those two modest demands fulfilled I either:
- Need to give up on my danish interface and crack my phone beyond warranty and a chance of bricking it.
- Disable HTC sense and go with WM interface
I know how limited I would be with any other phone, but this road I got myself on is really amazing
came99 said:
"I am really having a hard time locating a Danish language ROM.
I find FRE. GER, ITA, ESN, NLD, WWE, but no DAN????"
Then it aint just me being total clueless.. I cant find any either..
Im bafled by this world.. I basically have two modest demands: To record calls in mp3 and get easy access to my to-do list.. preferably on my homescreen, but just as good by one of the nifty Hotbuttons Ive seen in pictures..
To get those two modest demands fulfilled I either:
- Need to give up on my danish interface and crack my phone beyond warranty and a chance of bricking it.
- Disable HTC sense and go with WM interface
I know how limited I would be with any other phone, but this road I got myself on is really amazing
Click to expand...
Click to collapse
I found some Danish support threads, just search Danish Topaz in XDA and you may find something to load over a WWE rom.
Personnaly I think you will be disappointed if you do not take the plunge.
I had a Rhodium before my Topaz and once I go tmy Topaz, I couldn't stand it. It wouldn't do half the **** my Rhodium did. Because I had my Rhodium flashed to custom.
Finally HSPL was released and I flashed it immediately and can't believe I ever liked that other brick of a phone.
Take your time, get comfy with the process first, and read lots on the language packs.
The brick warning is just a disclaimer and it is very difficult to achieve if you follow the steps correctly.
I know these are expensive toys to take a chance on, but they really are only at 50% capacity out of the box. What a waste....
Bruce, dude, you're a saint. This is why so many folks look to xda for help. You should be commended, but probably won't be! You got my vote.
jdwilson said:
Bruce, dude, you're a saint. This is why so many folks look to xda for help. You should be commended, but probably won't be! You got my vote.
Click to expand...
Click to collapse
Thanks JD!
Is that commended or condemed???
Just trying to give a little back.
Greetz from SoCal.
I agree.. The helpfulnes here has been overwhelming, and has given me the bravery to try this out. But I am still very nervous.
Let me sum up what I learned from tonight.
1) When following your instructions I will have a phone which I can modify with custom roms.
2) As long as I am 100 % sure the rom is for Topaz I dont have to worry about messing up and bricking my phone due to doing wrong stuff to the radio-thingie? (yes, I still dont understand what that is)
3) I will be able to get back to factory defaults and warranty by installing the official rom you linked and afterwards install the original spl thingie afterwards?
4) Should I mess up and brick my phone, there is a fair chance of being able to restore it by the help of another device and a micro SD-card? (See I DO try and learn myself.. (Its probably incorrect though ))
5) I need to give up on the danish interface, but I will without too much hassle be able to get a danish keyboard?
6) To be absolutely sure not choosing a wrong ROM, please confirm this one as a possible choice: "Duttys Topaz HG R10 [5.2.23541.5.5.0]"
It is downloading and I am ready to take the leap... Geronimoooo!
came99 said:
I agree.. The helpfulnes here has been overwhelming, and has given me the bravery to try this out. But I am still very nervous.
Let me sum up what I learned from tonight.
1) When following your instructions I will have a phone which I can modify with custom roms.
Yes
2) As long as I am 100 % sure the rom is for Topaz I dont have to worry about messing up and bricking my phone due to doing wrong stuff to the radio-thingie? (yes, I still dont understand what that is)
Radio controls cell signal, GPS and WiFi connections.
3) I will be able to get back to factory defaults and warranty by installing the official rom you linked and afterwards install the original spl thingie afterwards?
Yes
4) Should I mess up and brick my phone, there is a fair chance of being able to restore it by the help of another device and a micro SD-card? (See I DO try and learn myself.. (Its probably incorrect though ))
Exactly.
5) I need to give up on the danish interface, but I will without too much hassle be able to get a danish keyboard?
Bingo!
6) To be absolutely sure not choosing a wrong ROM, please confirm this one as a possible choice: "Duttys Topaz HG R10 [5.2.23541.5.5.0]"
That's the one I am currently running. Great ROM!
It is downloading and I am ready to take the leap... Geronimoooo!
Click to expand...
Click to collapse
I'm usually not on the forum as much on the weekends but if you get stuck, shoot me a PM which will notify my e-mail and I'll see if I can help.
I take it you were successful with HSPL? If so, thats most of the battle!
Peace!
"5. With any luck, you won't get stuck at 0% and the flash will complete."
Well... Guess what...
Can someone please help.. Im stucked here and having a stroke.
Edit: Tried on 2 different computers and its the same: Stuck on 0 %.. Antivirus disabled.
Hi, if anyone could please help me i would be gratefull, i recently purchased a D2 but its already preloaded with WM6.5 rom version 2.53.405.5 (76952)WWE, But i really wanted WM6.1 as, among other things, i wanted to use the handwriting rec.
does anyone know what stock rom to reload? and where i can get it? sorry to ask such a basic question.
thanks in advance,
http://www.htc.com/europe/SupportDownload.aspx?p_id=249&cat=2&dl_id=613
thanks for that, however it seems to have just bricked the phone
thanks for that, however it seems to have just bricked the phone
it seemed to work, all the correct messages displayed
but......
now all that happens is it turns on, shows the touch diamond2 screen, then resets
it has the following text in red in the lower left hand corner
r 3 . 43. 25 .19
g 61. 20t. 25. 10U
d 1. 39. 47382
does any one have any ideas?
Try to hard reset.
tried that before i posted
and a soft reset, and another hard reset to be sure,
i searched the forum but couldn't find any reference to that type of error either.
any ideas on how to retrieve it from paperweight mode?
Download stock ROM for your region
Unpack it with WinRar or TotalCMD
Rename RUU_signed.nbh to topaimg.nbh
Copy topaimg.nbh on your SD card
Enter bootloader (hold volume down and turn on phone) and follow instructions
edit:I guess for wm 6.1 you need lower version of SSPL
thanks dude, i used the bootloader to reinstall the latest rom from HTC.
Topaz_S2_HTC_WWE_2.53.405.5_Radio_Signed_Topaz_61.44etc.25.35_4.49.25.91_Ship
my phone is no longer a brick however i am back to square 1 in that i still have wm6.5, and i want 6.1
ive tried to reflash with the older rom fighter7139 suggested
RUU_Topaz_HTC_WWE_1.39.405.3_Radio_Signed_Topaz_61.20t.25.10_3.43.25.19_Ship
but it gives me the same rebooting error.
any ideas why wont the older rom work on my phone? or if theres an alternative to that rom ?
thanks
I've loaded hardspl 1.83 and extracted the file RUU_signed.nbh and renamed it to topaimg.nbhand,
i moved it to the SD card, reflashed the phone with the 6.1 rom,
but i get the same error.
any idea on what rom i should use to update from?
or what stock spl i'd need to run this rom's version of 6.1 ?
a thought
maybe i don't even need 6.1, all i want to do is to fix two things -
1) make the sms messaging work like on the old htc devices ie diamond or tytn ie not use htc messaging
2) add handwriting recognition
- would also be nice to have the taskmanger icon, the battery icon and the original windows start menu back too, but im not dependent on them....
so i guess any rom would do that allows these functions, any help or info on this would be much appriciated
terminalkhaos said:
1) make the sms messaging work like on the old htc devices ie diamond or tytn ie not use htc messaging
Click to expand...
Click to collapse
Try http://forum.xda-developers.com/showpost.php?p=3771519&postcount=2991
2) add handwriting recognition
Click to expand...
Click to collapse
http://www.htc.com/www/SupportDownload.aspx?p_id=249&cat=0&dl_id=824
thanks for that, however that was the first thing i tried, i saw the download for the handwriting ap just after i got the phone, not knowing it didnt have it when i swapped from my diamond,
the thing is the update only works on certian AP version control builds -
the message on the site is -
Note: AP version control -> The criterion will pass if the Touch Input for Pocket is equal to Version 2.1 (Build1919.1320), or lower.
mines a higer version, which i assumed originally had to do with it being wm6.5 not 6.1,
- i have tried downloading and installing anyway but it wont load.
does anyone know how to get this update to load, or how to change the AP version control back to a lower version ?????
any help would be much appriciated.
if it matters,
i'm running Duttys HG, and ive flashed to hardspl,
i don't mind flashing back to whatever, i just really need the handwriting app
The handwriting SIP is likey hidden.
There is a reg edit to unhide, just search SIP Reg Edit and you should find it.
If I recall it was under the WM general tweaks.
thanks for that, i got the letter and block rec working, but still not the transcriber the reg key shows it should be showing, but i think the actual file may not be there,
fixed after changing the reg, and downloading the update, you then need this transcriber cab
http://forum.xda-developers.com/showpost.php?p=3661845&postcount=47732
result
Any luck finding a way to get 6.1 working on this phone? I just bought the Pure from AT&T as a replacement for my LG Incite that had 6.1 on it. So far I can't stand 6.5 at all. My main beef is with IE, I really like the one on my Incite vs. this one. And my other problem is with the start menu, I also prefer the drop-down style in 6.1.
Thanks for any replies or help.
TheNorthSideWhiteGuy said:
Any luck finding a way to get 6.1 working on this phone? I just bought the Pure from AT&T as a replacement for my LG Incite that had 6.1 on it. So far I can't stand 6.5 at all. My main beef is with IE, I really like the one on my Incite vs. this one. And my other problem is with the start menu, I also prefer the drop-down style in 6.1.
Thanks for any replies or help.
Click to expand...
Click to collapse
Start here.
Once you unlock your phone, you can flash to anything you want.
6.5 is hands down better than 6.1, there are 6.5.219xx builds that have the drop down start menu.
Thanks Bruce!
For some reason I couldn't find a good Pure forum, so that link helps a lot.
Edit: We now have a whole Q&A Forum...
Ok theres something I've been wonderin, it might be a toddler question but what are the guidelines for full Backup/Restore from one ROM to another (with same rom/sense build)? (using SPBbackup, RescoBackup, or SKtools)
And when I know I can't do a FULL restore what can I restore? (ex: Dutty r15 23569 --> Nhathoa 23123) prob not registry, but what about sys files?
Or if its just a different version of the same rom.. for example --
-- Full backup Energy Cookie Dinik 23569 (july2) -> Full restore after flashing Energy Sense2.5 standard. (and lets say I skinned a few things and installed apps like cleanRAM, IconChanger, Opera 10.. before the backup) -- Would it work?
Thanks.
Scabes24 said:
Ok theres something I've been wonderin, it might be a toddler question but what are the guidelines for full Backup/Restore from one ROM to another (with same rom/sense build)? (using SPBbackup, RescoBackup, or SKtools)
And when I know I can't do a FULL restore what can I restore? (ex: Dutty r15 23569 --> Nhathoa 23123) prob not registry, but what about sys files?
Or if its just a different version of the same rom.. for example --
-- Full backup Energy Cookie Dinik 23569 (july2) -> Full restore after flashing Energy Sense2.5 standard. (and lets say I skinned a few things and installed apps like cleanRAM, IconChanger, Opera 10.. before the backup) -- Would it work?
Thanks.
Click to expand...
Click to collapse
Basically,the only clean restore would be the same ROM to the same ROM, minus PIM data.
Let's say you're running Dutty HG15 23569 and he releases HG 16 23569 with fixes, whether registry, programs whatever, you would end up restoring over the changes.
With Manila, even if you back up your own ROM and restore, its not a good idea to restore your PIM data back to Manila as its been known to cause it to crash. However PIM backup works well for this.
I'm not saying it 'won't' work, but it 'can' cause issues.
I see.. Thanks!
So when restoring a backup from HG r15 to r16 like u said, besides PIMbackup, would any of these options be safe to restore
-databases
-registry
-system files
-device
-force rom upgrade (im not even exactly sure what this action does, just an option in SPB)
-Also Settings exporter from the same CHT ver.
Thanks for the help!
Use pim backup!!!
you better off using PIM backup and you wont screw it up...Use mortscript to create a script to install the files you need on first boot...(XDA-UC is written in Mortscript.). Just make .reg files, .cabs and what ever else you need , edit XDA-UC to your needs and you are ready to go!
Scabes24 said:
I see.. Thanks!
So when restoring a backup from HG r15 to r16 like u said, besides PIMbackup, would any of these options be safe to restore
-databases
-registry
-system files
-device
-force rom upgrade (im not even exactly sure what this action does, just an option in SPB)
-Also Settings exporter from the same CHT ver.
Thanks for the help!
Click to expand...
Click to collapse
Force upgrade is for different ROM builds. I wouldn't use it.
I use a combination depending on what I am restoring.
For same ROM restoring, I use SPB Backup with PIM disabled, and Google sync (gmail as exchange server) for contacts, e-mail and calendar.
For different ROMs, I only restore Gmail, my exported registries such as my sound settings, owner info, and various other tweaks I apply and databases.
Naturally any program specific settings would be fine.
As far as registries and system files, you could be restoring something that's incompatible or an older version.
Sashimi and User Config are 2 alternatives for auto installing your stuff.
Hope this helps.
Yeah I use XDA_UC with very few configs cuz I'm never sure if certain stuff will restore correctly. I seem to have trouble with settings exporter.
How do I restore specific program configs (bsbtweaks, advanced config, Tabs) without using the UC exporter or a full restore? Can I do it with SPB?
Because I like UC but just for CABs and PIMrestore (sometimes CHTedits)..
Sorry for all the Q's, I've been flashin a lot lately and always end up doin manual config labor and soft reseting a million times. But thanks a lot for the help!
I should note that the reason I don't use the Exporter is because I used it a bit before and when I would import the settings the bottom row of quicklinks would be all mangled and everything seemed glitchy. does this mean I was doing something wrong? I'm not sure but I think I remember NRGZ28 mentioning something in the changelog about an update/fix for UC so maybe I just need to try again.
How can I tell which Hard SPL / Factory SPL I have?
Hi All,
I have been reading the forums for a couple of weeks and I really want to flash my AT&T Pure with a new TOPAZ ROM. However, I got a second hand PURE and I don't know if they have done any modifications yet.
How can I tell which version or if they did change the stock SPL? Also, if there was a fail during the upgrade of the SPL would it still show the version and the phone still be functional?
This is what the bootloader screen says:
TOPAZ210 32M
SPL-1.83.0000
MicroP-Topaz (LED) v11
Turbo HW/Turbo SW
Thanks in advance!
snailspeeder said:
Hi All,
I have been reading the forums for a couple of weeks and I really want to flash my AT&T Pure with a new TOPAZ ROM. However, I got a second hand PURE and I don't know if they have done any modifications yet.
How can I tell which version or if they did change the stock SPL? Also, if there was a fail during the upgrade of the SPL would it still show the version and the phone still be functional?
This is what the bootloader screen says:
TOPAZ210 32M
SPL-1.83.0000
MicroP-Topaz (LED) v11
Turbo HW/Turbo SW
Thanks in advance!
Click to expand...
Click to collapse
It should say
SPL-2.51.OliNex or 1.83.OliNex
And it depends on the error you encountered. Did you try the upgrade already?
Thanks for looking into this. Well, I tried once to do upgrade (before checking what SPL version I had) and I got everything, but then the screen just showed 0%. I waited for a little bit, but then I just soft reset because it wasn't progressing. It shouldn't take that long, right? From the thread on the Olinex post, it seems like it should be over in a minute or so.
So does this mean I still have the stock spl?
snailspeeder said:
Thanks for looking into this. Well, I tried once to do upgrade (before checking what SPL version I had) and I got everything, but then the screen just showed 0%. I waited for a little bit, but then I just soft reset because it wasn't progressing. It shouldn't take that long, right? From the thread on the Olinex post, it seems like it should be over in a minute or so.
So does this mean I still have the stock spl?
Click to expand...
Click to collapse
Possibly, I just upgraded the latest version right when I got the device. I did have a bit of trouble with my upgrade though. Did you follow the steps exactly?
I ended up having to install a cab file (enablerapinew). Then it worked fine.
You can always try removing the battery/SD/SIM for a min or 2, put em back in, establish connection, then follow the steps.
Otherwise you should read the troubleshooting and Q&A.
SPL-1.83.0000 is the stock SPL I'm pretty sure by the way
Scabes24 said:
Possibly, I just upgraded the latest version right when I got the device. I did have a bit of trouble with my upgrade though. Did you follow the steps exactly?
I ended up having to install a cab file (enablerapinew). Then it worked fine.
You can always try removing the battery/SD/SIM for a min or 2, put em back in, establish connection, then follow the steps.
Otherwise you should read the troubleshooting and Q&A.
Click to expand...
Click to collapse
I tried again following their "automatic flash" but then I got the error of the server being down or something. I will try again. I have flashed ROMs on other phones, but this one is giving me a bit of a problem. I also tried the Manual version, but it didn't put the phone in the bootloader mode, it kinda just stood there.
So you followed the directions like they posted? Any other hints or tips? I installed the enablerapinew too.
EDIT:
I figured it out, I am such an idiot. Thanks for your help. After installing the enable I did a soft reset. That was what I did not do. Thanks. Any recommendation on a stable ROM? I am looking at Nhathoa's
Nice, yeah NhatHoa is good. I've been using the Energy ROMs.. close-to-stock and fully loaded versions available.
begin with htc pure rom install
I'm not finding link for how to take an htc pure with AT&T rom and install Tom Topaz Rom. Looking for link for instructions. Right now it has the AT&T rom and I don't know how to take the file and apply it to the phone. The AT&T provided rom is an .exe file.
knightto said:
I'm not finding link for how to take an htc pure with AT&T rom and install Tom Topaz Rom. Looking for link for instructions. Right now it has the AT&T rom and I don't know how to take the file and apply it to the phone. The AT&T provided rom is an .exe file.
Click to expand...
Click to collapse
Check out this thread first, it is the pre-guide to learn the basic:
forum.xda-developers.com/showthread.php?t=585457[/url]
knightto said:
I'm not finding link for how to take an htc pure with AT&T rom and install Tom Topaz Rom. Looking for link for instructions. Right now it has the AT&T rom and I don't know how to take the file and apply it to the phone. The AT&T provided rom is an .exe file.
Click to expand...
Click to collapse
Do you have Hard-SPL already?
Can't get sms dialog to automatically rotate to landscape mode
Hmm, I'm still not sure if this is the right thread to ask a general, non-rom-development topaz question... It says so in the first post, but the thread is located in the rom development section - strange...
Anyway, I'll try: I'm using the latest cookie sense 2.5 energy rom for my diamond2, but the problem existed on all previous (energy) rom versions - whatever I try to add to the touch tools' rotation manager (or g-config), I can't get the sms writing dialog (htc "threaded" or "normal" version) to automatically rotate to landscape mode when I turn my phone. Nothing happens... I have a default hard button assigned for doing that and that works flawlessly. Other apps added to g-config rotate automatically...
I'm desperate, anyone willing to help? Is there some setting I have to enable or some registry tweak to apply or something? I searched the forum but users don't seem to have any problems with that, so I must be doing something wrong...
Thanks!
About the Touch diamond 2 Resitive touch screen problems ^^; , My Lovely diamond 2 if there cold , My diamond 2 automatically Touch in the center .. , Can you help me ?