Does not ask for passcode when connecting a bluetooth headset - Touch Diamond, MDA Compact IV General

I've got a cheap headset from dealextreme.com. The pairing should be fairly easy (hold a button until the headset flashes red and blue, and search for bluetooth devices using the phone).
I do so, and Diamond finds the headset. I connect, but Diamond never asks for a passcode.
The result is that the pairing between the headset and Diamond is lost every time I turn of the headset (which makes it practically worthless).
I tried pairing it with my laptop. The laptop ask for a passcode, I enter "0000" as told in the manual. The pairing stays even if I turn the headset off and on again.
Is there a "trick" to be done? I thought I had paired enough bluetooth devices over the years, but this was new to me...

winmobile automaticly tries the "standard" bt-headset passcodes like 1234, 1111 and a few others. if they fail you will be asked to enter one yourself. it's weird that it fails. have you done a complete reset of the headset?

I would, if I only could figure out how to do that...
The manual in "engrish" does not tell me how to, allthough it's listed as a step in the "Failure guide".

My headset pairs as yours does, automatically, as 0000 is the passcode.
If I turn off my headset and turn it back on again, it doesn't appear to pair back but if you make a call or receive one, it pairs straight away then puts the call through.
Have you tried any calls after turning off headset then on again?

My jabra headset resets if you press all buttons at once for a few seconds, but i guess you've already tried that.. same moskus as in the hw.no and smartmobil forums?

Yes, I've tried to make a phonecall after a "reboot". However, it's like Diamond doesn't know that the headset is even turned on.

me too!jabra bt500

Related

Can't switch bluetooth headset off on call

Since I upgraded to Summiter's Test2 and now the multi-installer, I can not switch to phone handsfree. There is a button on the call status page that says "speaker on". It used to be I could press that and it would switch to speaker phone (away from BT). Now pressing that button does nothing.
The reason this is a problem is that it's easy to leave the BT headset in a different location than the phone. If I initiate a call from the phone, it automatically connects to the BT headset.
On recieving calls, I know to press the hard button for "talk" and it will let me use the phone in the traditional mode (even if the BT is connected). BUt when I initiate a call, I don't have any choice like that.
Thoughts? Am I the only one with this problem?
RayB

Customized bluetooth headset settings?

I have a Tilt and the 510 Voyager headset. I'm wondering if there's a way to do the following two things:
1. When the headset is turned on and connected to the phone is there a way that I can make it so that I can still talk on the phone? It seems like when the headset is turned on that the microphone and sound is muted on the phone, so you have to use the headset.
I want to be able to use either the phone or the headset at the same time.
2. If I walk out of range of the headset while it is turned on, then walk back in range, can I set it so that the headset will automatically reconnect?
1. You can switch from the headset to the phone during a call. It is one of the options on the "call screen". I don't believe you can set it to default, but you can just turn off bluetooth if you want the default headset to be the phone.
2. The headset should automatically reconnect when brought back in range. Try pushing the "pick up" button on the headset. It should automatically re-pair in a second or two.

Bug: Bluetooth Headset not *really* connected on boot-up

I've been experiencing this problem on my TyTN II with the original ROM. The programs I have installed which may be affecting the problem are:
-CooTek TouchPal 2
-TIInit_4_2_38 Kaiser (Official HTC Bluetooth Fix)
- duttythroy v3 Voip Setup
- Microsoft Voice Command v1.6.17913
Here's the problem:
- boot up the TyTN II (after being completely powered off) or toggle Bluetooth power off & on, with paired bluetooth headset within range and on
- Go to Phone screen. Headset icon is there indicating that the Bluetooth headset is connected.
- Press talk/send button on Bluetooth headset to start Microsoft Voice Command or answer an incoming call.
Result: Headset beeps as expected, but nothing happens on the TyTN II. Voice Command is not initiated. Incoming calls are not answered.
Workaround: If I go to Start>Settings>Connections>Bluetooth... Tap & Hold on my Bluetooth Headset, then choose "Set as Hands Free" the headset beeps again indicated that it made a connection. After I do that, all is as it should be! I can activate Voice Command, and answer/end calls with the Bluetooth Headset. I should not have to set my Bluetooth Headset as the Handsfree device everytime a reboot or toggle the Bluetooth power status.
I suspect it might be the Voip implementation, or the HTC Bluetooth "fix" but haven't done a hard reset yet to test.
Has anyone else had this problem? Does anyone know of a solution??
What headset are you using? I have the same software (except ROM) as you and haven't experienced this problem. I can SR with headset on and it will reconnect once the device reboots.
I tried it with the Nextlink Invisio G5, and Bluespoon AX2, both of which worked properly with other phones (HTC P3300, Nokia N95, etc., etc.,). I can try other headsets, but I'm pretty sure it's the phone software.
If your Voip and MS Voice Command are the same as mine and everything is working properly, maybe it's the HTC Bluetooth "fix". I guess another hard reset is in order soon.

[Q] Bluetooth Headset Won't Stay Connected

I've been using a new bluetooth headset for about a week now, and suddenly it won't stay connected to my Pure. I have not done anything different to the phone to affect the bluetooth settings, and I've checked them several times anyway and everything seems normal.
I even deleted the pair with the headset, re-paired, but still the same results. The headset is properly recognized, it connects to the phone normally, but after about 20 or 30 seconds it disconnects.
If I turn on the phone's bluetooth, turn on the headset, then make a call after it connects, the call is properly routed to the headset but only for those first 20 or 30 seconds. What's worse is when the headset disconnects from the phone during the call it doesn't just revert the call to the phone's mic & speaker, it ends the call.
By the way, the headset is a NoiseHush N450, but I don't think the problem is with the headset because the same thing happens when I pair my phone to other BT headsets.
Any ideas?

How can I pair a Bluetooth headset?

I've got a Verizon tab and am trying to connect to a Bluetooth headset so I can make video calls with Fring or something else with a little more privacy than using the speakerphone.
I can't get the tab to find the headset!
I have successfully paired with a Bluetooth keyboard, mouse, and the Jawbone Jambox. While the audio out on the Jambox works fine, the built in mic does not work for speakerphone calls with the tab either.
Anyone have any idea what I can do?
Refer to the headset menu to perform a hard reset on it (on a nokia headset this done by simultaneously pressing power and action buttons till it alternates its LED between red and green). Activate the bluetooth on the tab and make it discoverable. In bluetooth setting scan for devices till the headset appears.
Same Issue
slamorte said:
I've got a Verizon tab and am trying to connect to a Bluetooth headset so I can make video calls with Fring or something else with a little more privacy than using the speakerphone.
I can't get the tab to find the headset!
I have successfully paired with a Bluetooth keyboard, mouse, and the Jawbone Jambox. While the audio out on the Jambox works fine, the built in mic does not work for speakerphone calls with the tab either.
Anyone have any idea what I can do?
Click to expand...
Click to collapse
I have a TMobile tab with the same problem. It connects to my btooth antenna, but not my two btooth headsets.
My headset bluetooth also facing the same problem. I read the manual and it say i have to press the answer button for more than 8 second as a hard reset to the headset. Later my tab can detect the headset.
You should read the manual and try to do hard reset to your headset
Sent from my GT-P1000 using XDA App
Can't seem to find out how to reset the headset. Nothing in the manual or Google (it's a Samsung HM1100).
It's weird - the Astro Bluetooth network shows the headset in its Bluetooth explorer but the GT will not even see the device to pair to.
Firstly you open bluetooth under setting, wireless & network. Press scan for bluetooth. Result, it will not show any bluetooth found. Press back button once only. And again open bluetooth setting. Then you will see all bluetooth devices already detected.
This is a bug. I happen all the time to me.
Please try it
naimmkassim said:
Firstly you open bluetooth under setting, wireless & network. Press scan for bluetooth. Result, it will not show any bluetooth found. Press back button once only. And again open bluetooth setting. Then you will see all bluetooth devices already detected.
This is a bug. I happen all the time to me.
Please try it
Click to expand...
Click to collapse
Still No Luck.

Categories

Resources