Wizard stuck in Bootloader - 8125, K-JAM, P4300, MDA Vario Software Upgrading

hey guys help me out here
i upgraded my ipl/spl to 3.08 and den wen flashing touchflo rom it had an error at 99% saying communication error ...
now wen i did da recovery and tried to reflash it .... in the bootloader when i insert the usb cable and start the upgrade utility the active sync disappears and den it shows an error the check da connection ...
can anyone tell me whats wrong and what to do
thanx

How to unbrick a phone search
If you search the forum for posts on how to "unbrick phones" you may find a solution.

Yeap
whateveryouneed said:
If you search the forum for posts on how to "unbrick phones" you may find a solution.
Click to expand...
Click to collapse
Search on wiki or just try this... reset your PC, dont run any other program on your PC neither the internet explorer neither the file explorer please then... sof reset your device, don't do a hard reset! remember just softreset. even if the activesync is not workind put your wizard in bootloader rgb screen and conect it via usb.... wait a little to see in PPC screen usb in a little letters at bottom... then start the upgrade original ROM to back to ipl/spl 3.08... are you sure that your device is cid sim unlocked?
download the Wizard service tool to check it please.... then retry the upgrade touchflo...

Related

PDA2K stuck on boot screen

i have downloaded update rom v 1.40 form the imate site. and connected my device to my PC via bluetooth link and sync through active sync4.5 and then run the update setup setup found the device v 1.22 and ready to update it to v1.4. and then after the restart (which the setup automaticlly does) a display with out back light appers which says (Serial v2.07). i tried to soft reset and hard reset but nothing happens, on the short i am unable to load os on my device and stucked to this display (Serial v2.07). i do not have data cable or cradel. any solution Please.
****
Moderator edit
Thread moved from news section to Blue Angel Upgrading
****
did you find a solution
because i have the same problem with mine
soegaard71 said:
because i have the same problem with mine
Click to expand...
Click to collapse
I have the same problem but i'am with mda III T-mobile can Any one help me ??????
well i do not want to offend you but you are too stupid to even try the upgrade over bluetooth, the upgrade only can be performed over cable
Get a cradle or a data cable and update according to descriptions in the Wiki. You're in bootloader mode, you should be able to resume the update from here, but ofcourse only by cable.
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel_WM5_Home
worst case scenario is to recover your device using mtty, search the forums for the method
Or you can find it in "the guide" which can be found within the wiki (near xplode ROM)
I really want to improve the wiki - but the ****ing time

How to Flash in BootLoader

I have a stuck image on my 8125. The phone "boots" but only shows a white screen, and is unusable.
The "a2sd all" restore option mentioned in the forums doesnt work for me. I have read on several forums that I should be able to reflash the OS from the bootloader, though I cant find any instructions on how to do this
Could someone point me in the right direction for how to flash an OS VIA bootloader?
Thx
1. Get the phone to bootloader (tree color mode) - I think by soft resetting and pressing the camera button at the same time
2. Connect it to the computer (Windows XP) with a USB cable
3. You will notice "USB" written in a lower corner of the phone (this means it is connected)
4. Now you can flash your provider's ROM without any problems
I am not sure whether the bootloader flashing is possible from Windows Vista.
You must flash normally (in bootloader you cannot use either shelltools or SoftSPL - so use your provider's ROM).
Mirek
Mirek - not to be totally ignorant, but the step 4 is what I'm having problems with .... where can I find either a providers ROM, or something that I can actually use while in bootloader mode?
Thanks!
NM ... Found it!
For anyone reading this .... You can get the provider ROM for the 8125 from HTCAmerica here: http://www.htcamerica.net/support/8125/software-downloads.html
Thanks for your help!
mirekluza said:
1. Get the phone to bootloader (tree color mode) - I think by soft resetting and pressing the camera button at the same time
2. Connect it to the computer (Windows XP) with a USB cable
3. You will notice "USB" written in a lower corner of the phone (this means it is connected)
4. Now you can flash your provider's ROM without any problems
I am not sure whether the bootloader flashing is possible from Windows Vista.
You must flash normally (in bootloader you cannot use either shelltools or SoftSPL - so use your provider's ROM).
Mirek
Click to expand...
Click to collapse
Dear Readers,
I'm having problem with my Dopod 900(,Qtek 9000,HTC Universal,O2 Xda Exec,Jasjar ). Can somebody please tell me what to do?
Before this, every time somebody called, the PDA lost the network bar and start to search or network and reject the calls automatically and also i wasn't able to send SMS. Now, i tried to install WM6 crossbow, the phone even cannot be on !!! even when i connect it to the charger, even the light will not be on. the only page that i can see is a white page asks Press 0 to Restore factory default or press X to exit. either perss 0 or X, the phone will be off and i cant turn it on with power key....
Please tell me what can i do ?? I really need your help.
PLEASE REPLY, PLEASE.
[email protected]
Warm Regards to All
G-Jorji
brick?
hey guys, i need a little help. i downgraded my phone to buttons rom and then i was gonna attempt to upgrade the ipl/slp to 2.xx. so i downloaded the wizard ipl/spl 208 from the ftp site. i had a successful flash but when it went to reboot, my wizard never turn on again. ive searched the forums but it seems to me i have a brick found nothing. has anyone had the same situation happen to them? and find a solution?
it wont turn on at all anymore
acuraholic said:
hey guys, i need a little help. i downgraded my phone to buttons rom and then i was gonna attempt to upgrade the ipl/slp to 2.xx. so i downloaded the wizard ipl/spl 208 from the ftp site. i had a successful flash but when it went to reboot, my wizard never turn on again. ive searched the forums but it seems to me i have a brick found nothing. has anyone had the same situation happen to them? and find a solution?
it wont turn on at all anymore
Click to expand...
Click to collapse
WHAT did you downgrade from?
Did you re-unlock your G3?
How's your battery?
acuraholic said:
hey guys, i need a little help. i downgraded my phone to buttons rom and then i was gonna attempt to upgrade the ipl/slp to 2.xx. so i downloaded the wizard ipl/spl 208 from the ftp site. i had a successful flash but when it went to reboot, my wizard never turn on again. ive searched the forums but it seems to me i have a brick found nothing. has anyone had the same situation happen to them? and find a solution?
it wont turn on at all anymore
Click to expand...
Click to collapse
IPL/SPL 2.08? Does that exist? Do you mean 3.08?
Are you sure your device is a G3? Or you killed it when flashing Button's ROM?

Error 246 Device not responding

I'd bought my htc p3600 pro (black, free from sim-lock & free from any carrier) from London.
As advised by TRINITYGUIDES.INFO site I tried to do HardSPL with all the three available HardSPL files, but of no avail.
When the HardSPL's progress bar comes(on pc) it gives a message on my phone " Enterbootloader.exe....This may harm your device...Do you want to continue.." I pressed yes & the process stopped & gave an error on pc "Error 246 Device not responding" & on phone screen showed the bootloader with
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
I did soft reset on my p3600 & its working as usual with it original spl infos.
I want to put official WM6 SEA version(ROM+RADIO) on my phone...Please help.
I too have the same message when I try to upgrade to hard spl as per teh guide here: http://trinityguides.info/index.php...ask=view&id=25&Itemid=66&limit=1&limitstart=2
Can anyone help? I have tried updating active synch... could there be anything else?
I have flashed my rom befroe to unlock the GPS but I now want to upgrade to WM6.
I guess the hard spl is a failsafe and I can skip this step?
Thanks
wingnutLP said:
I too have the same message when I try to upgrade to hard spl as per teh guide here: http://trinityguides.info/index.php...ask=view&id=25&Itemid=66&limit=1&limitstart=2
Can anyone help? I have tried updating active synch... could there be anything else?
I have flashed my rom befroe to unlock the GPS but I now want to upgrade to WM6.
I guess the hard spl is a failsafe and I can skip this step?
Thanks
Click to expand...
Click to collapse
Search is great function
http://trinityguides.info/index.php?option=com_content&task=view&id=37&Itemid=67
wingnutLP said:
Sorry!
I am an idiot.
Thanks
Click to expand...
Click to collapse
sorry I tried a Google search on the error message and came up with this thread!
wingnutLP said:
sorry I tried a Google search on the error message and came up with this thread!
Click to expand...
Click to collapse
Search more...
With this link:
http://www.google.com/advanced_search?q=+site:http://forum.xda-developers.com&hl=en&lr=&as_qdr=all
if you search error 246 you will get the solution on 11th answer.
Search more...
Have the same [Error 246]! How can I definitly fix it?
Hi,
first of all, sorry for my poor English. I try to explain my problem so good I can... I hope you can help me.
I have the "[Error 246] Device not responding" problem.
I have used a lot the "search"-function and I have found a lot of posts which propose the same solution "restart the Rom upgrade another time". Ok I did it and my PDA works very well, but now I would like to solve the problem radicaly... How can I solve this problem? Should I use SPLexploit (I have found the guide on trinityguides.info) and then reflash a Hard-Spl?
Thx a lot
ciao
Tompo
Some specifications....
Sorry.... I have a P3600 White with Olipro 1.20 and rom Elias 1.9 SE Lite...
Tompo81 said:
Hi,
first of all, sorry for my poor English. I try to explain my problem so good I can... I hope you can help me.
I have the "[Error 246] Device not responding" problem.
I have used a lot the "search"-function and I have found a lot of posts which propose the same solution "restart the Rom upgrade another time". Ok I did it and my PDA works very well, but now I would like to solve the problem radicaly... How can I solve this problem? Should I use SPLexploit (I have found the guide on trinityguides.info) and then reflash a Hard-Spl?
Thx a lot
ciao
Tompo
Click to expand...
Click to collapse
Before flash manually enter bootloader. After start the rom update utility. (As www.trinityguides.info suggest). You will not get error 246 any more
thanks for answer
Many thanks for anwser...but...
Is this the only solution? If is so, then everbody has this problem, isn't so?
Ciao
Tompo
Tompo81 said:
Many thanks for anwser...but...
Is this the only solution? If is so, then everbody has this problem, isn't so?
Ciao
Tompo
Click to expand...
Click to collapse
www.trinityguide.info
Here is written to flash rom you should manually enter to bootoader. In this case, you will not have error 246.
Most of the people know this, so they have not this problem
Those who not manually enter bootloader can get error 246, and this way of flashing is not as safe as the manual bootloader way.
(because in this case you use the spl uploaded by RUU, not the hard-spl on the PDA)
Ok, now I really understand
Ok, this is a very good anwser, short and clear... thanks...
Ciao
Tompo
fktsndr said:
www.trinityguide.info
Here is written to flash rom you should manually enter to bootoader. In this case, you will not have error 246.
Most of the people know this, so they have not this problem
Those who not manually enter bootloader can get error 246, and this way of flashing is not as safe as the manual bootloader way.
(because in this case you use the spl uploaded by RUU, not the hard-spl on the PDA)
Click to expand...
Click to collapse
When i connect my touch hd to pc in active sync mode, then shutdown device an run in bootloader (volume down and power button at same time) i get the tricolor screen and after a while i get the progress bar on my phone and on pc. But i stays on 0% and says 'update error' after a while.
please help
I Have the Same Problem the Status bar Freeze On 0% and nothing happened
Until the Update Error Message Displayed
Please Advice
Thank You
Note: I Have HTC Diamond2 (Topaz) Without Sim Louk
Hi Me has the trinity 3600 as a VPA GPS vodafone branding, and i get the same error message trying to run the bootloader and entering tricolor screen, ---> error 246 aber manually starting into bootlaoder and restatrting the romupdateutil.exe same error 260 no connention...
So you guys have a working version of the updating ?
And please remove all the links which are not working, linking a solve for the 246 problem, there are nomore links available...
thanks
Dome
I found a way to solve the problem 246 go in you mobile device, -->start -> settings-> connections ->USB to PC open this. Remove the hook @ Advanced networksettings activation! ---> click OK--> close
try again the bootloader etc, then on the tricolore reboot screen is shown USB in the lower white field and the bootloader can do its routine complete.
Have Fun with flashing the phones!
Testet with original German Vodafone available ROM " vpa_comp_gps_RUU_Trinity_VF_DE_1_23_162_4_6275_1_29_00_01_13000_108_Ship.exe "
testet with ZackMcRofls superfast german rom " RUU_Trinity_GER_1.23.162.2_GPS_v3f_by_ZakMcRofl "
testet with
" htcp3600_RUU_Trinity_HTC_GER_1-23-407-2_103_6275_1-38-00-11_108 "
First was Zack´s rom, 2nd. was Original Rom, 3. was Trinitys rom, after trxing all, i flashed Zacks Rom again, it was the best in my view.
Thank you verymuch, bb

[HELP] installing new rom stuck on 99%

After i tried to install a new rom it stuck on 99% when i put my phone on it will only go to the bootloader... what can i do???
kevinalmere said:
After i tried to install a new rom it stuck on 99% when i put my phone on it will only go to the bootloader... what can i do???
Click to expand...
Click to collapse
Always post the data of your your phone,to get help.
secondly you had a bad flash,perhaps your phone is CID locked. Which rom were you trying to flash ?
Now to recover,download the official carrier's rom and flash it while in bootloaders.The phone will start working again in default status,then,Read and understand the unlocking method and the flashing guide,read the stickies carefully and perform the method correctly.
cheers !
i have a t-mobile vario:
ipl 1.06
sp 1.06
i removed the simlock with lockwizb and a tried to put airfawizard rom on it so now i have this tricolord screen en there is nothing i can do.. tried to update i with the original carrier rom but it says update error so in seems it can't see my phone or something but my usb is plugged in i hope i can fix this i only can see this blue green red screen it drives me crazy hope you can help me.....
Help!!!
I have same Problem with TNE-V1.0n_4mb.exe
IPL 3.08
SPL 3.08
kevinalmere said:
i have a t-mobile vario:
ipl 1.06
sp 1.06
i removed the simlock with lockwizb and a tried to put airfawizard rom on it so now i have this tricolord screen en there is nothing i can do.. tried to update i with the original carrier rom but it says update error so in seems it can't see my phone or something but my usb is plugged in i hope i can fix this i only can see this blue green red screen it drives me crazy hope you can help me.....
Click to expand...
Click to collapse
If you can go to boot loader, most likely you will be ok. When you plug in the usb port, does the words in the screen change from serial to USB? Once it changes, then flash your official, and then CID unlock your device (this is different from SIM unlock). Then flash to the ROM you want!!
PS: Go read wiki about how to unlock and flash and understand more about your device. http://wiki.xda-developers.com/index.php?pagename=HTC_Wizard
The only thing it does is going to bootloader and when i plug my usb in it say usb but when i try to install my original rom from t-mobile ( a update ) it says it's looking for information on my mda but after a couple of second it's say UPDATE ERROR i use windows vista can that be a problem? and how do i know wich one is the original..?
kevinalmere said:
The only thing it does is going to bootloader and when i plug my usb in it say usb but when i try to install my original rom from t-mobile ( a update ) it says it's looking for information on my mda but after a couple of second it's say UPDATE ERROR i use windows vista can that be a problem? and how do i know wich one is the original..?
Click to expand...
Click to collapse
Vista dont like upgrading and stuff...but there is a work around, search the forum and see if you find it. Or try using XP.
okee problem solved working again
thanks for your help!!!
kevinalmere...
How did you resolve the issue I'm having very simular problems and believe it's my Vista OS causing the problem..
Orange SPV M600 G4
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 4.0.0.0
Sorry should explain my issue incase anyone can help.
I attempted an upgrade to WM6 using an Upgrade .Bat from this site. I was slightly impatiant due to not being able to complete the downgrade first anyway the upgrade frose, after a while I canceled the update and carried out a hard re-set... Since then I'm not able to boot nor connect to my desktop via Active sync (WMDC (Vista))
I've followed every instruction I can find but only to be meet with RUU Errors saying can't connect or file open. I can however acces my Bootloader screen and when connection is made the USB symbol shows on the screen of my phone...
Any help would be greatly recieved......

Hspl error check THE picS

HELLO
i'm going crzay from the hspl
the auto flash dosn't work
and the manual flash file when i run it the device is lag
so i get into the bootloader by pressing volum down and power then realese
and i start the manul flahs then here is the 7 pictures i put it in zip file cu they more than 4 file
hope we fix the proplem
plz
plz
plz
help
SYRIAN4E said:
HELLO
i'm going crzay from the hspl
the auto flash dosn't work
and the manual flash file when i run it the device is lag
so i get into the bootloader by pressing volum down and power then realese
and i start the manul flahs then here is the 7 pictures i put it in zip file cu they more than 4 file
hope we fix the proplem
plz
plz
plz
help
Click to expand...
Click to collapse
Might have been more help asking in the hspl thread but nevermind . Try a different cable (most mini usb cables will do)
SYRIAN4E said:
HELLO
i'm going crzay from the hspl
the auto flash dosn't work
and the manual flash file when i run it the device is lag
so i get into the bootloader by pressing volum down and power then realese
and i start the manul flahs then here is the 7 pictures i put it in zip file cu they more than 4 file
hope we fix the proplem
plz
plz
plz
help
Click to expand...
Click to collapse
no need to go crazy, this can be fixed.
you shouldn't enter the bootloader yourself, it won't flash that way.
what error did it say in automatic mode?
syrian
tha messeage talk about turning off my firewall
and the server is off
and this is my first hspl
SYRIAN4E said:
tha messeage talk about turning off my firewall
and the server is off
and this is my first hspl
Click to expand...
Click to collapse
ok did you turn firewall off? turn proxy off too, if you have a proxy.
if that doesn't sort it, I can still help you if you message us via this link: http://support.htc-unlocks.com/
syrian
i change the usb and disable the proxy and turn off all my firewall and antivirus
i think the proplem from something lagging from the hspl software
cuz i enter the bootloader and i start manual flash and it's respond and show to me the update button and i press it and tell my software version and if i wanna change to oilnex version and i press it and show to me the percentage image on the pc and in the phone then i wait then nothing happend
SYRIAN4E said:
i change the usb and disable the proxy and turn off all my firewall and antivirus
i think the proplem from something lagging from the hspl software
cuz i enter the bootloader and i start manual flash and it's respond and show to me the update button and i press it and tell my software version and if i wanna change to oilnex version and i press it and show to me the percentage image on the pc and in the phone then i wait then nothing happend
Click to expand...
Click to collapse
you shouldn't enter the bootloader like that, the flash won't work that way.
I replied to your priv. message
syrian
is there any hope CHECK THE PICTURE
1st - the cable is work well cuz i update the device with it from the offical htc website
2nd- the picx
3rd- i run the EXE in the device and it SHOW TO ME THIS MESSAGE : Lic OK
4TH- I START THE manual FLASH
2nd- more INFO
RED LINE : TOPA100 32M
SPL-2.51.0000
MicroP-Topaz (LED) V10
TURBO HW/TURBO SW
GREEN LINE : TP MFG DATA
502,547 170,876
173,200 834,210
828,869 Calibrated
BLUE LINE : E M P T Y
WHITE LINE : U S B
SYRIAN4E said:
is there any hope CHECK THE PICTURE
1st - the cable is work well cuz i update the device with it from the offical htc website
2nd- the picx
3rd- i run the EXE in the device and it SHOW TO ME THIS MESSAGE : Lic OK
4TH- I START THE manual FLASH
2nd- more INFO
RED LINE : TOPA100 32M
SPL-2.51.0000
MicroP-Topaz (LED) V10
TURBO HW/TURBO SW
GREEN LINE : TP MFG DATA
502,547 170,876
173,200 834,210
828,869 Calibrated
BLUE LINE : E M P T Y
WHITE LINE : U S B
Click to expand...
Click to collapse
the screenshots are very helpful in seeing what your problem is.
ok, after 3rd step now try copying Manual SSPL exe (link: http://forum.xda-developers.com/attachment.php?attachmentid=232407&d=1254155476) on the phone, run it, it should then show SSPL screen on the phone. then use the Manual flash mode on the PC. let me know if it works that way
syrian
the device get LAG when i launch the manual sspl and i start manual flash even whene it's lag
and here is the picture
SYRIAN4E said:
the device get LAG when i launch the manual sspl and i start manual flash even whene it's lag
and here is the picture
Click to expand...
Click to collapse
what do you see on the phone screen at this point?
syrian
nothing just the file maneger when i launch the manual sspl cuz the device lag
SYRIAN4E said:
nothing just the file maneger when i launch the manual sspl cuz the device lag
Click to expand...
Click to collapse
ok you did step "3rd- i run the EXE in the device and it SHOW TO ME THIS MESSAGE : Lic OK"
and then you run the manual sspl EXE on the phone, it still lags ?
I'm asking to make sure you did not do a hard reset or anything (I mean, don't do hard reset)
syrian
i just did it in ever way that you can imagine
and i think that the manual is the proplem i'm sure
is ther any hspl type haha we can use
SYRIAN4E said:
i just did it in ever way that you can imagine
and i think that the manual is the proplem i'm sure
is ther any hspl type haha we can use
Click to expand...
Click to collapse
ok one last check.. send me a screenshot of your phone showing the IMEI to make sure it's OK.
but do not post the screenshot publicly, send it in private message.
syrian
come on xda help me lol
SYRIAN4E said:
come on xda help me lol
Click to expand...
Click to collapse
alright I realized that the second file was the wrong version. I sent you the correct file in PM, let me know if it worked
syrian
OMG it's WOrk good
thanks a LOT for you
i own you
LOT
LOOK how much time it take to fix this proplem LOL
now i have another proplem and it is if you won't
is how to download the duty or energy rom cuz they are upload on HOTFILE and RAPIDSHARE LOL
and i thanks for the second time and love to know what was the prolem
SYRIAN4E
SYRIAN4E said:
OMG it's WOrk good
thanks a LOT for you
i own you
LOT
LOOK how much time it take to fix this proplem LOL
now i have another proplem and it is if you won't
is how to download the duty or energy rom cuz they are upload on HOTFILE and RAPIDSHARE LOL
and i thanks for the second time and love to know what was the prolem
SYRIAN4E
Click to expand...
Click to collapse
glad to help. as I said, the manual SSPL in the thread was the wrong version. I forgot to update it at one point, will add it in the thread now. (most people can just go and use automatic mode so nobody noticed there was an issue with the file.)
Hi all
I really need some help please!!
I think I have read and searched and tried steps by step all the posts and threads on this, none of them work for me,
Ive flashed my HD2 & TD2 with HSPL, radios and roms many times in the past. I have a stock rom on my TD2, (havent flashed a cooked one yet but did on my HD2 and worked great),
the problem is when I try flash anything, (HSPL,Radio's and Roms)
I connect with WMDC on windows ultimate 64x and go through all the steps, the phone disconnects from WMDC when loading the tri-color screen, and installs the HTC sync drivers fine, and then (my problem) it hangs on 0%. this happens regardless of what I'm flashing after a while brings up the communication errors 208 & 260. this doesnt have any effect on the software HSPL or radio as a soft reset returns back to the homescreen just fine. I am running HSPL 1.8.3. , radio 4.49.25.17 and a shiped stock wm 6.5.
This is what Ive tried so far:
I have used 3 different micro USB cables,
updated my .net fx to 4.1
I have tried different Ruu's such as custom Ruu, Ruu from topaz, Ruu, supplied with Hspl, flashes center and KaiserCustomRUU.exe and a few others.
Ive tried the white screen fix many times. including the SDA unlocker and stuff.
I ve tried manual and automatic.
tried entering the the Tri-color screen manually and via the Ruu.
I tried different computers and different operating systems (W7ultimate and XP 32Bit and 64Bit)
tried active sync WMDC 6.0 and 6.1
Ive removed the SD card and sim and have tried flight mode
Restarted pc's mobile any reinstalled WMDC many times.
Ive tried renaming to the HSPL, radio and Rom to TOPAIMG.nbh , put 1 by 1 on formated fat32 SD card, run from Tri-color menu. all of them just hang on
loading....
Have tried mixing and matching Ruu's with HSPL's, Roms And radios and everything else i can think of, after 18 hours of this I am fed up and decided i need some help
Thanx in advance
ok
i have now download the official RUU_Topaz_S2_HTC_WWE-AFK_2.53.421.3_Radio_Signed_Topaz_61.44etc.25.35_4 .49.25.91_Ship.exe Rom
and it worked with no problems.
it updated my HSPL from 1.83 to 2.51 and radio version to 4.49.25.91 which was exactly what i was going for.
The problem now is that i still cant change my HSPL, RADIO or flash a custom Rom which is what I need. it hangs on 0% and now gives me a 262 error which states that:
ERROR [262] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process. If this happens, you can just soft reset the device and run RUU again. The update process will then continue. At this stage the rom on the device is incomplete and it will not boot back up into Windows. You will need to place it into the bootloader to continue.
which is not true as if a reboot it doesn't continue the update and just returns to the home screen as normal
help?

Categories

Resources