Related
from several days ago whem i touch in diamond icons never select the one i touch!!!... It selects the icon on left or right but never the right one....
When i have a phone call i select the green icon and it turns the phone off
What can i do?
I aligned the screen thousands of times, i installed the different calibrators and nothing.
I align screen, it works well for a few seconds and becomes crazy again. I soft reset, a tried everything i remember and always the same.....
Obvious question: Did you Hard Reset?
Try a hard reset.
If that doesnt work then it sounds like the screen is screwed, get the unit swapped.
I've just installed a new rom! I think i have to swapp the unit
The problems are the same. Anything more i can do??
If you just installed a new ROM, did you do a hard reset? To me it sounds as if the calibration for the touch sensor is off. The first thing that you do after a hard reset is calibrate the screen.
So you can try to calibrate the screen, bofore doing the hard-reset.
You can but when you hard reset you just have to do it again
Also, you could check your local optician for any additional problems.
No, but honestly, a hardreset and recalibration should fix the problem. I'm aware that GNes/GSen can give some problems if it thinks it has rotated the screen, but I've never seen that occur outside programs that don't rotate the screen by themselves.
If that doesn't work, Sync it, back it up, whatever you want to do, possibly flash to stock and return it to whereever you bought it/HTC to get it swapped.
thank's everybody... I tried it all and the same. Going to swapp
have the same problem.. it wasn't there before, had the phone for 3 month.. i think it has to do with water under the screen, used it in the rain and then it began to behave this way (due to the big speaker hole maybe?) , it works fine otherwise! Any idea how to fix it? waterdamage? - guarantee or what?
I think it´s wierd if you can´t use it when it´s raining..?
joel78 said:
I think it´s wierd if you can´t use it when it´s raining..?
Click to expand...
Click to collapse
How many phones can be used risk free in rain?
i don't think that's the problem. no water in my phone, rain or other....
i think it started after gsen installed...may be wrong, or else or.....
Very little chance Gsen having anything to do with it. Many people are using that (including me) with no ill effects.
Hmmm, I though I was the only one with this problem. I'm on the second unit now, the first one always do soft reset by itself after every few wake up. Now the alignment always gone off after few minutes of use. I'm waiting for the replacement unit now.
Initially I thought it was because of the ROM update I did, but even after I restore the original ROM, it still happen.
Looks like I'm quite unlucky with the Diamond .
problem solved!!!!
gone to look for assistance.
After 3.30 hours new touch screen and they sad to me new components inside.
For now all good. Till when??....
hope it was the last problem
So its a guarantee issue? - bad components inside?
It still works ok, so i wait to send it away..
till now all ok.
I have done a reasonable amount of searching on this and have not found anything specific to my problem so figured I should post a question.
I have an issue with my Dimaond when it gets hot generally either using Wifi or Phone Data connection that the screen goes out. Basically everything goes to the left side of the phone so if you hit the Task Icon in the top right corner you get the Start Menu. Phone is basically useless at this point and you have to wait for it to cool down. Has happened since day one and is generally worse when using it when charging. I was watching Utube on it the other night 5min video while on AC charge and it went out. I am running Dutty 2.5 Rom and 25.07 radio have tryed 25.08 and 25.05 no difference was happening when the phone had orginal HTC ROM as well. Also will happen on a long call if the screen is on.
Basically feel issue is hardware related and maybe faulty screen still under warrenty so wanted to know peoples opinion on weather I should send back. Problem is will take a couple of weeks and I don't really wnat to wait that long if I can help it. Also assume it would be best to flash standard ROM back, should I do anything with HARDSPL eg should this be changed back as well if I send it back.
And before anyone says it I have tryed searching this topic and have found lots about HOT dimaonds but nothing related to screen going out at the same time :-(
Thanks
I had this issue in my JasJam (Hermes) whre the screen would simply go white after a while of use and I would have to leave it for a while for it to work again.
Unfortunately it sa hardware issue and you should claim a warranty repair on it
I can't see how this could be a software problem so I figured it must be the screen eg hardware related. Would be nice to know if anyone has had the same issue with a dimaond... Seems we may be spending some time apart, just hope it doesn't take long to fix..
I've had the same issue
http://forum.xda-developers.com/showthread.php?t=428976
My first device had been replaced recently (i.e. today) by my network provider (o2) and the new device seems to work without any problems now even if it's "hot".
(i.e. default screen adjustment + creating heat by activating the phone, wlan, bt + recharging it)
I sent an email to HTC regarding the fault and they said it would have to go back for a warrenty repair. I brought it through a resellar so has to go back to HK from NZ so will be away three weeks uurggghhh... Just seems odd I don't have any physical damage on the screen but hte problem has been around since day one as I remember having the problem the first day I got it. Juyst seems to be getting worse and is easily reproduced by usiung utube over wifi gets hot and it is all over. Just wondering if I should put an offical ROM from HTC back on the device before I send it back as I currenty am running Dutty ROM, what do you think....
i put the original rom back on and they still found out the the rom had been flashed, and would not repair on warranty
yep, i also asked about this problem
http://forum.xda-developers.com/showthread.php?t=438733
there are some youtube video's of how the phone behaves
my phone seems to do it less frequently since stopping using panosha's rom
im using alpha zero 7 at the moment..
i've also noticed that it isnt necessarily a heat issue, my phone does it completely at random
yesterday i found though, that when the phone did the alignment issue, i gave it a good shake.. and hey.. its all aligned again?!
maybe it was just a fluke, it hasnt freaked out since..
holding thumbs
Hey,
I also have the same screen problem, but my Alignment goes to right.
If I press on the left side, a press on the right side is recognized.
Good to know that Im not the only one with this problem.
greets doena
I got my phone back a week ago replaced the screen has been away for over two months, complete disaster, anyway all sorted now and I have not had the problem since....
I had this exact same issue (out of the box).
It was a hardware fault and I exchanged it for another one.
Haven't had any problems since.
Minus-1 said:
I had this exact same issue (out of the box).
It was a hardware fault and I exchanged it for another one.
Haven't had any problems since.
Click to expand...
Click to collapse
Hardware's fault ? Most likely not. I will give u an example of why I think it was software related. My device ran hot as well but I simply switched roms and now it's the complete opposite. Your most recent device most likely come with a different Rom in the phone.
hey guys
have been a reader more than a poster on this awesome site..
but i have run into some trouble :/
within the past week, everytime my phone gets slightly hot, the screen alignment goes totally out.. like really out..
for example i manage to open the notes app..
if i tap the extreme left side, the draw tool will draw in either the center, or even far right.. its extremely frustrating.
Happens mostly after a phone call, using gps, or plugging phone into usb/charging..
im using Panosha's 2.2 full
Radio .05
I have tried loading the original HTC rom that came with the phone... no difference..
any help would be greatly appreciated
oh, and i do re-align... 10-15 times a day..
when the phone is cool, it runs like a dream
eyetac said:
hey guys
have been a reader more than a poster on this awesome site..
but i have run into some trouble :/
within the past week, everytime my phone gets slightly hot, the screen alignment goes totally out.. like really out..
for example i manage to open the notes app..
if i tap the extreme left side, the draw tool will draw in either the center, or even far right.. its extremely frustrating.
Happens mostly after a phone call, using gps, or plugging phone into usb/charging..
im using Panosha's 2.2 full
Radio .05
I have tried loading the original HTC rom that came with the phone... no difference..
any help would be greatly appreciated
oh, and i do re-align... 10-15 times a day..
when the phone is cool, it runs like a dream
Click to expand...
Click to collapse
...sounds like a hardware issue!
really? :/
damn
its only 2 months old..
wouldnt have anything to do with cooked roms right?
i really cant afford a void warranty
eyetac said:
really? :/
damn
its only 2 months old..
wouldnt have anything to do with cooked roms right?
i really cant afford a void warranty
Click to expand...
Click to collapse
When you have the same probs with the htc original rom, then it has nothing to do with a cooked roms :-(
http://www.youtube.com/watch?v=5-IUzerAT0s
exactly what mine does
even right after a screen re-align
sigh
cyron_at said:
When you have the same probs with the htc original rom, then it has nothing to do with a cooked roms :-(
Click to expand...
Click to collapse
ok, thanks dude
will take it in and hopefully get a replacement
another example of what mine is doing pretty much to the T
http://www.youtube.com/watch?v=ZhQIyqnTkS4&feature=user
if anyone may have a solution.. please let me know asap.. as i will try taking it in on saturday
thanks guys
damn, mine does the same from time to time!
does anybody have a solution?
did a replacement fix the problem?
unfortunately i havnt had a chance to take it in yet, but i have logged the problem with my service provider..
the problem occurs alot more when i used panosha's rom/s
with the default (and now alphazero) the problem seems less frequent, but definitely still happens..
happened badly yesterday when i used gps to get my girlfriend to a casting, but switched on car A/C and after 5 minutes it was cool again *shrug*
its really annoying though
will let u know when i finally get to taking it in, unless u get there first
Hi there, I have the exactly problem what you had. Whenever the machine is hot, it becomes mad. Any solution could be reslove the problem?
It really sounds like a hardware issue... When you return the phone to the store please flash back to the original stock rom (for warranty purposes )
same problem
i am getting he same alignment problem.i do it many times a day but still tapping somewhere on screen taps the other way.very difficult to dial phone numbers
cyron_at said:
...sounds like a hardware issue!
Click to expand...
Click to collapse
i dont think its an hardware issue,as after i align it works fine for few hours and then i have to align again to make the taps work acurately.........i have heard there is a cab file for it.if any one can post it here.........................or make a cab file so that clicking it makes the alignment as it was default with the new phone
It is a hardware issue. the screen somehow (usually when carried in front pants pocket) will get pressed and SHIFTED. Then screen pushes against the side-cover and this fools the touch-sensitivity of the screen. Try yourself - try to shift screen to one or other side, and directly after it will be better. it's still a service matter though. Send it for repair.
This is a known issue. You need to exchange the unit for a new one.
hey guys...
so late last year i took the phone in and it spent 3 weeks at leaf (HTC distributer here is south africa)
i got the phone back, turned it on in the store.. and guess what... still screwed..
i threw my toys to say the least and got a brand new phone..
the new phone was 110% up until 2 weeks ago..
it started doing the same damn thing (to a lesser extent)
i have found that its a connection problem..
the touch pad is very all over the place if used normally (so basically its unusable)
but if i hold down the top left of the phone(pushing down just above the start menu) with my left hand and use my fingers on my right.. the phone works perfectly again..
does anyone know how to fix this?
its so frustrating, especially knowing im going to be without it for 3 weeks or more again
hmmm ...
i heard that the radio-part is for managing the curcuits.
try an other rom.
but i cant give garanty, i hard it only.
I just got my Diamond back from repairs and wanted to compare experiences:
1)
I first bought a Diamond two months ago. It came with 1.37 ROM series on it, the screen wasn't too yellowish, but touch function wasn't responsive and the GPS was a MESS!
(of course, I tried many ROMs official and unofficial, almost every Radio ROM and various Hard-SPL. None of that fixed the problems.)
I could cope with with the other flaws, but I just couldn't bear my GPS wasn't getting a fix, no matter how much sattelits were in view...
It worked at first, but soon started to display '66666' instead of the location and finally, it would never display any location again.
I tried every tips and tricks and softs, it helped giving me more and more satellits in view and apparently active, but at the end my crappy GPS could never turn the datas received into a proper location...
2)
I sent my device back to warranty (after flashing back to official ROM and SPL) and had to wait for about a month.
(the technician at first tought I was just a noob unable to set his phone properly, but after two days of attempts, he had to admit that there was something wrong with my phone and sent it to the the headquarter for replacement of motherboard and so on.
3)
The new phone I got came directly with 1.93 ROM and a little bit more yellowish screen, though, there is no spot or stain on it. So the coulour doesnt bother me.
But from the beginning I noticed the new phone was much more responsive even at the slightest touch.
From the first try, the GPS got a fix in about 1 mn time, with only 3-4 satelits in view.
I installed Hard-SPL and the latest Australian Official ROM, and though the screen seems now a little less responsive than before, the GPS is still working, fine.
I'm a VERY happy user of Diamond now, but I'm still wondering one thing:
it looks like once the warranty technicians understood that I was very demanding about quality and complete functions, they took time but gave me a phone totally different in terms of behaviour and quality of the components sensitivity of screen, GPS etc.
Is there some bad production series that they never tells publicly about, and much more better series that they give you as a replacement once they understand you will bother them until the end of time if you are not satsified?
Plz tell your experience about having received two new diamonds with totally different behaviour and quality of the components.
I guess you are totally right!!!
My first device was pealing paint in the aluminium frame on the second day, work very good by the way.
Now i´m on the second device and i my hardware keys, especially the call button is sometimes irresponsive and i have to push it several times to enter the dial.
Tried cooked rooms as well, and the call button issue still remains, so i´m a little unhappy with my diamond experience.
I've noticed that whenever i turn on my display after having left the diamond unused for sometime the lcd doesn't switch on smoothly, what i mean is that it first displays a grey pattern(only for a ms or so) and then the desktop( lcd off>>grey flash>>desktop). Usually the transition from off to desktop is quite smooth, but in my case its not!
Is this a s/w issue or h/w ?
I've never experienced that particular problem myself, but sounds like H/W problem to me...
just been through a couple of other threads related to the grey screen of death...i've had it once...it happened while i ended a call, had to soft reset to resolve it.
take a look at the grey screen of death i'm talking about
Pretty scary indeed!
It might not be a coincidence that you experienced both: grey transition when switching on the screen and once, the grey screen of death after a call...
Two different effects of the same defective part in your H/W?
a solution!, almost
untill now i've had auto brightness control switched off and the brightness was set to minimum to save battery life, but now i just tried switching on auto adjust backlight and the problem seems to have vanished.....coming out of standby is smooth as ever!
although i've to say that i don't quite understand the logic behind it.
*EDIT*
it doesn't help for long
blufade said:
a solution!, almost
*EDIT*
it doesn't help for long
Click to expand...
Click to collapse
This is what I was worrying about...
Your method sounded like a work around to avoid the display failure. But as a matter of fact, there must be a reason for the display to fail. (bad screen, power supply or something...)
By the way, I'm more and more convinced about my assumption that there are bad production series and better ones:
Today I had my device connected to my PC through USB for a couple of hours. In the meantime, I was downloading and deleting messages, watching google video on opera, after that I used wifi etc.
In this situation, my first Diamond would have got hot like hell and my hand could barely stand the pain...
Since many people were complaining about over-heat problems, I thought that was a common problem with Diamond.
But the new one did not get that hot. Just a little over-warmed, but definitely not too hot. From that phenomenon, I can see what I felt about a better touch-flow behaviour, a better GPS and so on is a part of a whole:
I was first sold a ****ty phone, and now I finally got a proper Diamond!
People with bad series, you don't have to cope with all those troubles, ask for a replacement phone!
my diamond gets heated up quite a bit at times....but i dont fully uderstand what exactly is the cause.....i've had experiences with the diamond getting pretty hot while using wifi & or gps and on another occasion i was watching a DVDRIP via wifi(@ full power) using core player and also with gps cycle running in the backgroud, still the diamond stayed well within reasonable limits.
i think it has to be a software problem, possibly the radio s/w
would you mind sharing the radio version of your diamond?
As written in my signature, I'm using the 1.00.25 which is included in all latest official ROMs.
By the way, I hope you did not cast a spell on me! (just kidding)
Today I experienced my first grey screen!!!
My Diamond was connected to the PC through USB cable, downloading e-mails, and I got a phone call. When I hung the phone, It suddainly happened, for the first time in my Diamond user carreer!
Just for one second, looking like an old black and white TV screen trying to tune on channels.
Hope that was the first and last time. In ordinary calls, (without being synchronized to the PC at the same time, it never happened so far...
sorry to hear that my friend
My Diamond was connected to the PC through USB cable, downloading e-mails, and I got a phone call. When I hung the phone, It suddainly happened, for the first time in my Diamond user carreer!
Click to expand...
Click to collapse
I'd the same experience except for the fact that my diamond wasn't connected to a PC.
I hard reseted my diamond yesterday, but the grey splash while i turn on the display from standby(post 3) still exists ( ......i don't suppose its a software problem anymore.
blufade said:
i don't suppose its a software problem anymore.
Click to expand...
Click to collapse
Why not trying to send it back to the seller and get a new one?
This problem is easy to demonstrate to the technicians, and I don't think they will be cheeky enough to say that's a normal phenomenon!
This problem is easy to demonstrate to the technicians, and I don't think they will be cheeky enough to say that's a normal phenomenon!
Click to expand...
Click to collapse
not that easy.....the thing is that if we turn on & off the lcd without a gap of atleast 4-5 min(dono exactly) i dont see that grey splash
i think im going to wait another 3-4 months before i approach for warranty.
I had that "gray splash" problem with my Kaiser and Diamond.
Hard reset also didn't work like above. For both devices the fix was simply flashing to a different (cooked) ROM.
As mentioned in another thread, the grey screen problem was fixed (as least for me when I flashed to dutty's rom)
blufade said:
not that easy.....the thing is that if we turn on & off the lcd without a gap of atleast 4-5 min(dono exactly) i dont see that grey splash
i think im going to wait another 3-4 months before i approach for warranty.
Click to expand...
Click to collapse
You can stay there and wait for 5 more minutes in the shop while they are attending other customers, just to proove your point.
If they are honest, they will not deny the fact!
foxium said:
I had that "gray splash" problem with my Kaiser and Diamond.
Hard reset also didn't work like above. For both devices the fix was simply flashing to a different (cooked) ROM.
Click to expand...
Click to collapse
knave said:
As mentioned in another thread, the grey screen problem was fixed (as least for me when I flashed to dutty's rom)
Click to expand...
Click to collapse
There might be some tweaks in the cooked ROMs that avoid the problem, or it might be due to some bad flashing or defective hardware.
If not, how do you explain that I've never experienced this with my previous HTC phones (wizard, Trinity...) nor I experienced it with my Diamonds (the first one and the new one) with stock or cooked ROMs.
except for that very special time, when I received a call while downloading messages through Active Sync.
Ok, this might be the first real problem I've had with my tilt, in a sense that I have no freakin clue what happened or how to fix it. The front buttons on the tilt as well as my keyboard decided they wanted to stop working and I have no clue how to bring them back... let me start from the beginning.
I installed m2d about 2 weeks ago, its kind of laggy but I'm still impressed with the overall UI as it compliments the tilt. Some bugs started popping up here and there but through the forum I was able to make it run relatively smoothly. Last night my tilt wouldn't connect to my computer, the usb contacts might have gone bad or something, it only works when I put pressure on the cable to keep the contacts together. Than today my screen would wake up for no reason, with no programs or application running in the front or background of the device. It was annoying to say the least. Than I got my first text of the day and went to respond using the actual keyboard, no dice. No response from the keyboard. So as Im typing using the stylus I tried to delete something, and the backspace button on the touch keypad isn't working, so more problems. I want to try and hard reset the device to see if that fixes the problem, but since I can't use the hard buttons on the front of the device I can't hard reset (the scroll wheel, ptt, and ok buttons aren't working either) Is this anything anyone has ever heard of? My tilt is kind of battered after a year of use, but nothing significant has happened within the last month to make me think that something inside came loose, especially since this just started today and it was just sitting on my table all night. I appreciate any and all help. Thanks in advance.
might be "m2d" not compatible ... hair wired ..
I wonder ..whether we can install window CE from pc to h/p through usb link ...
"Last night my tilt wouldn't connect to my computer, the usb contacts might have gone bad or something, it only works when I put pressure on the cable to keep the contacts"
r u using original usb cable ..b'cos now a day I saw many only using normal "small" usb cable head which easily spoil the connector at phone ... too loose for that sharp..
l3urton32 said:
Ok, this might be the first real problem I've had with my tilt, in a sense that I have no freakin clue what happened or how to fix it. The front buttons on the tilt as well as my keyboard decided they wanted to stop working and I have no clue how to bring them back... let me start from the beginning.
I installed m2d about 2 weeks ago, its kind of laggy but I'm still impressed with the overall UI as it compliments the tilt. Some bugs started popping up here and there but through the forum I was able to make it run relatively smoothly. Last night my tilt wouldn't connect to my computer, the usb contacts might have gone bad or something, it only works when I put pressure on the cable to keep the contacts together. Than today my screen would wake up for no reason, with no programs or application running in the front or background of the device. It was annoying to say the least. Than I got my first text of the day and went to respond using the actual keyboard, no dice. No response from the keyboard. So as Im typing using the stylus I tried to delete something, and the backspace button on the touch keypad isn't working, so more problems. I want to try and hard reset the device to see if that fixes the problem, but since I can't use the hard buttons on the front of the device I can't hard reset (the scroll wheel, ptt, and ok buttons aren't working either) Is this anything anyone has ever heard of? My tilt is kind of battered after a year of use, but nothing significant has happened within the last month to make me think that something inside came loose, especially since this just started today and it was just sitting on my table all night. I appreciate any and all help. Thanks in advance.
Click to expand...
Click to collapse
Go to Start/Settings/System/Clear Storage
and your usb is probably whack
@kaiserII...your usb is whack, haha. that **** made me laugh.
having same exact issue
ya it happened to me sunday night, having exact same problem. keyboard doesnt work, and my front buttons dont work exept for the the center button which ends up opening the start menu (wrong command). Im over my 1 year warrenty and not sure what to do. Had to buy a cheap 40 dollar nokia for the time being, please help if someone can. Oh and I did a hard reset, and it didnt fix anything. Booted android with it and 1 out of 5 times the buttons came back, this is really weird/vexing.
l3urton32 said:
Ok, this might be the first real problem I've had with my tilt, in a sense that I have no freakin clue what happened or how to fix it. The front buttons on the tilt as well as my keyboard decided they wanted to stop working and I have no clue how to bring them back... let me start from the beginning.
I installed m2d about 2 weeks ago, its kind of laggy but I'm still impressed with the overall UI as it compliments the tilt. Some bugs started popping up here and there but through the forum I was able to make it run relatively smoothly. Last night my tilt wouldn't connect to my computer, the usb contacts might have gone bad or something, it only works when I put pressure on the cable to keep the contacts together. Than today my screen would wake up for no reason, with no programs or application running in the front or background of the device. It was annoying to say the least. Than I got my first text of the day and went to respond using the actual keyboard, no dice. No response from the keyboard. So as Im typing using the stylus I tried to delete something, and the backspace button on the touch keypad isn't working, so more problems. I want to try and hard reset the device to see if that fixes the problem, but since I can't use the hard buttons on the front of the device I can't hard reset (the scroll wheel, ptt, and ok buttons aren't working either) Is this anything anyone has ever heard of? My tilt is kind of battered after a year of use, but nothing significant has happened within the last month to make me think that something inside came loose, especially since this just started today and it was just sitting on my table all night. I appreciate any and all help. Thanks in advance.
Click to expand...
Click to collapse
Exactly the same thing has happened to me!! Coming on randomly, draining the battery really quickly and the same keys doing the same things as yours i.e. nothing or Start menu. The backspace and space don't work on the on-screen keyboard either. Is it the end of the road or has anyone the slightest idea what the hell to do!?!?!?
Same issue but slightly different
2 days ago I started hearing a noise from my phone that was not something I normally hear. After checking my phone I found out it was the voice recorder program opening up on its own. It started repeatedly doing this and recording automatically. I had to hold down the close option (X) and before it would stop. AFter a reset and when the phone wakes up it always does this now. Along with all these whacky problems my hard buttons stopped working. My scroll wheel and D-pad sometimes work and only the up, down, left and right arrows work on the keyboard. Camera button seems to work sometimes also. All others have stopped responding. Except for holding the power key. I just reflashed my phone to latest phoenix ROM and problem is the same. Is this it for the phone or is there a fix.
Anyone??? Please!!
Try this free fix
I had the same problem as the original poster. My fix was to download AE Button Plus trial and use it to reset my keys to their original setting. I did not have to do the keyboard, just the external keys. Now my tilt works like it used to.
This fixed the problem when clear storage and reloading roms did not.
It doesn't hurt to try since the trial is free.
Good Luck,
Will
same here... help pls...
any one yet has found a solution for this issue??? 2days ago my Kaiser suddenly started with same problems, buttons dont work and the recorder goes on, any one yet found a way to fix it??? thanks...
I have no idea if this will actually help anyone but I installed japanese input on my kaiser once and during the process a registry got edited that stopped my hardware keyboard and the hardware keys (front keys) from working and the fix was to correct the value:
[HKEY_LOCAL_MACHINE\System\CurrentControlSet\Contro l\Layouts\e0010411]
edit the 0010411 value to "00000409"
again I have no idea if this will help but it wouldnt hurt to check to see if the registry somehow got changed. Goodluck and I hope you guys figure it out.
didnt work...
dantegl36 said:
I have no idea if this will actually help anyone but I installed japanese input on my kaiser once and during the process a registry got edited that stopped my hardware keyboard and the hardware keys (front keys) from working and the fix was to correct the value:
[HKEY_LOCAL_MACHINE\System\CurrentControlSet\Contro l\Layouts\e0010411]
edit the 0010411 value to "00000409"
again I have no idea if this will help but it wouldnt hurt to check to see if the registry somehow got changed. Goodluck and I hope you guys figure it out.
Click to expand...
Click to collapse
thanks anyways "dantegl36" but it didnt work...
I have the same issue
This is intresting, I just posted on this, as I am having the same issue, which of course just started a few days ago. I have the updated UI as well but I installed it as well.
Any idea how to fix it??
keyboard fix "edfc" problem
yes , kaiser tweak slide wake disabled ...it OK
Greetings from Olsztyn Poland
Unfortunately, the problem returned it was only a temporary improvement, sorry
For my tytn2 after rom upgrade, the front buttons do not respond except the central one. the side buttons are responding under the win only but in the bootloader screen they don't respond. and I cannot make a hard reset.
I did a hard reset through the setting menu but still the problem has not been solved. Adding on that the keyboard doesn't work except the arrow keys.
Do anyone can figure a solution for that. except the hardware problem bec I am out of warranty.
Did anyone was able to solve the problem fully?
oo wow, i have the same problem. hope theres a fix
adding to that the the bluetooth is turnino on by itself even if I switched it off and the device by itself after time of switching it off it refuse to start again unless I did a soft reset.
I tried all the avilabe suggestion but nothing worked.
Hiya
This seems to be a problem with the TyTn II - there are several threads in this forum about it, none of which have any working solutions that I ever found...
I spent ages trying different ROMS, Radios and pressing of buttons and haven't found a solution - other than to disown the TyTn II and get another phone! I did pick it up again the other day and it is still refusing to have working buttons or keyboard (as reported by others, only the central buttons seems to work all the time as a Start Menu button).
I did manage to stop it eating battery at a ridiculous rate by turning it to specific radio settings rather than letting it find its own GPRS/ 3G and phone band. I think it was in this thread
I was considering sending my TynTn II to HTC, but I'm not sure it's going to be worth the postage and their service fees as I've already replaced it with a Touch Pro 2. Then again if we ALL sent them in, they might acknowledge some sort of problem with this model.
samstables said:
Hiya
This seems to be a problem with the TyTn II - there are several threads in this forum about it, none of which have any working solutions that I ever found...
I spent ages trying different ROMS, Radios and pressing of buttons and haven't found a solution - other than to disown the TyTn II and get another phone! I did pick it up again the other day and it is still refusing to have working buttons or keyboard (as reported by others, only the central buttons seems to work all the time as a Start Menu button).
I did manage to stop it eating battery at a ridiculous rate by turning it to specific radio settings rather than letting it find its own GPRS/ 3G and phone band. I think it was in this thread
I was considering sending my TynTn II to HTC, but I'm not sure it's going to be worth the postage and their service fees as I've already replaced it with a Touch Pro 2. Then again if we ALL sent them in, they might acknowledge some sort of problem with this model.
Click to expand...
Click to collapse
can I know how did u mange to change the rom? bec even my side buttons refuse to work whenever I am at the bootloader screen and the upgrade through the active sync failed.