Flashed DID diamond+sprint rom and my phone is stuck in the Touchdiamond screen when it vibrateds first can anyone help me..
tried a Hard Reset?
(hold down center button and volume down while pressing reset for 3 secs)
Yeah thats the first thing i did..no luck just goes back to the start screen.
can u get to Bootloader?
Not sure how to get there..
umm.. Volume key up and reset i think (if not check Wiki)
once in Bootloader you can connect to PC and try flashing ROM again
if this doesnt work, try flashing original ROM (same process) and try a different version of Hard SPL. have u flashed other ROMS ok before?
It use to go in bootloader shen i pushed volume dwn, power button and enter botton..not doing it now..
its Volume Down and reset - my bad
Got to chip off now, good luck with it PM me and i'll see it tomrrow if u still got problems
No luck i have tried everything stuck in this loop anyone have anyother sugjestions
I can get it to go to the hard reset screen but that itanyonter way to force it into bootloader the direction in the manuel are different from what wiki says..
So is it bricked?
Related
OK i did a search but did not find anything really related..
a friend of mine at work here just handed me his 8125 after "attempting" to flash his ROM. Not sure what the heck he did BUT
1) the usb is not recognized so not active sync.
3) 3 battery meter only shows a plug (lower right ) yet the battery works.
the phone does recognice the charger..
HELP !!!
thanks in advance !
Reset, enter bootloader, reflash
how do you enter boatloader .. ?
what other 2 buttons with the soft reset button ?
DUlrich1227 said:
how do you enter boatloader .. ?
what other 2 buttons with the soft reset button ?
Click to expand...
Click to collapse
Camera Button is the only one you need to hold when resetting...
i apologize but i must be missing something..
i reset (soft reset and camera button) get cingular screen
starts to boot up and goes to today screen where it does not recognize usb..
is there something else i am to do ?
DUlrich1227 said:
i apologize but i must be missing something..
i reset (soft reset and camera button) get cingular screen
starts to boot up and goes to today screen where it does not recognize usb..
is there something else i am to do ?
Click to expand...
Click to collapse
Press the reset (or power down your device by holding the power button until you get the Okay to turn-off warning).
HOLD the camera button as your device powers up. This will get the BootLoader
just woke up and read your reply thanks ..
this is what i ended up doing
i bluetoothed from one of the roms enterbootloader.exe was able to run it
than ran one of the earlier rom upgrades..
re running the lockiwizb and will install sumters rom2
one question if you read this .. on both of the phones 8125's i get an error at the end of the bat file when running the lockiwiz.. is this normal ? is it because it was already ran once ? i am running it from the root (C
I flashed my HTC 3600 over a weekago but all then for no reason my phone will only go to the splash screen displaying the HTC logo.
I have tried to reflash but the reflash gets to 1% before failing with corrupt rom message on the pc and the phone rebooting to the htc logo again..
has anyone go any ideas..
Thanks Steve
Try a hard reset.
tried a hard reset but the phone only goes to the splash screen
Try booting into bootloader, the key combination is on the Wiki. From there you can flash all again.
sorry for being an idoit but i dont understand i have the bootlader screen up,
but the flash refuses at 1% what is wiki?
http://wiki.xda-developers.com/index.php?pagename=Trinity_Resets
Bootloader mode: Hold side Camera and POWER buttons together and reset with stylus.
Thanks for that i have tried this and it bring the bootloader up fine then when i flash it says corrupt rom, with all the roms not just one,
someone says i can reflash using mtty?
Hello everybodies,
I just upgrade ROM on my kaiser htc, now it's doesn't work, it's boot indefinetly...
Someone can help me plz, thx in advance
Does it start loading the OS? Or is it on the tri-color bootloader screen.
Try enter the bootloader (camera button pressed + reset) and load the ROM again.
Try a hard reset first, if you haven't. I did something at some point that caused that to happen and a hard reset straightened it all out.
Listen to your heart....
I'll try to load it again vcespon and inform you...
It requires blood, prick your finger and feed the tilt.
Try the hard reset or see if you can put it into bootloader mode (power button + camera button + reset). Connect via active sync and see if you get USB and can reflash (or flash a different ROM).
My diamond freezes on the startupscreen where you see in the lower left conrner the R, G and D versions in RED.
Can this be fixed?
Yeah I am rite now having the same problem anyone has any suggestions the soft-reset button doesn't work and it is not recognizing my network provider... anyone has any suggestions....
hard reset also doesnt work :-(
Yea since the soft reset button doesn't work I am not sure wht to do it is just stuck up on the startup screen can anyone give any suggestions please.....
if i only could acces the internal storage, put a rom on it, and do a flash with hard reset buttons, then it could be back 2 live but now
Can you get it into bootloader? {Hold Vol. down button while pressing power}
If it will go into bootloader, you can flash from there.
It worked
1. i've put it in bootloader [Hold Vol. down button while pressing power]
2. connected the diamond to my pc with USB-cable
3. Install the original rom
Thx supersanj
I tried to unlock my diamond, now it turns over, I try a hard reset, it works not so.
when I plug in the charger, the LED does not light.
what should I do, help me pls!
Here is the link where I downloaded the flash: ppcgeeks.com/Diamond/Users/Tob...20Unlocker.rar[/url]
Yep, just did the same.. Got an error that it was the wrong model id at the end. Now i cant enter bootloader, its a brick.
http://forum.ppcgeeks.com/showthread.php?t=36062
Have you tried going back into bootloader via the power button and volume down?
I have the same problem.
Did you solve it or not?
If you did what did you done?
you can not solve this problem my friend becouse i made the same thing and the phone is dead....I just found some litle informations in my searches and it can be done only by jtag mode
so if u are an expert and if u have a programmer u maybe can do this.....
here is the link : http://forum.revskills.de/viewtopic.php?f=25&t=117[/URL]
Maybe Ill can Help
Once i stuck in the boot of my phone in a rom everytime i turned it on ? oO but i solved the problem (after 2 ****in weekz without phone)
But this is what i Did
Ill simply pressed this at same time(Vol down, reset button & back arrow)
and deleted the which deleted the old OS backup (your phone still works)
and then i turned it off and pressed the same combo again
which will turn your phone in USB mode then put it into ur PC u maybe wont see it but that doesnt matter the same happened 2 me just go 2 HTC website from ur country and download the latest ROM update they got and let it load into and when ur done just reset ur phone and everything should be OK u can just load a new custom rom (Note u need HardSPL Installed i do not think u can do without ) just PM me if u need more help
blackster said:
Once i stuck in the boot of my phone in a rom everytime i turned it on ? oO but i solved the problem (after 2 ****in weekz without phone)
But this is what i Did
Ill simply pressed this at same time(Vol down, reset button & back arrow)
and deleted the which deleted the old OS backup (your phone still works)
and then i turned it off and pressed the same combo again
which will turn your phone in USB mode then put it into ur PC u maybe wont see it but that doesnt matter the same happened 2 me just go 2 HTC website from ur country and download the latest ROM update they got and let it load into and when ur done just reset ur phone and everything should be OK u can just load a new custom rom (Note u need HardSPL Installed i do not think u can do without ) just PM me if u need more help
Click to expand...
Click to collapse
I tried this with mine and it did nothing. Anyone else have any ideas?
thanks.
EDIT: I got mine working by pressing Power + Vol Dwn + Enter (circle button) + reset and hold them till the screen turns white. then follow the steps on the screen.